STRUCTURAL REPAIR AND OTHER REPAIRS TO DISTRESS CONCRETE AND SUNKEN FLOOR AND REPAIR TO JOINERY LEAKAGE SEEPAGE AND PLUMBING WORKS INCLUDING WATER TANK AND FLOAT VALVE AT MAP D TYPE E TYPE F TYPE QUARTERS IN SAILORS MARRIED ACCOMODATION AND OTM A

Amount

Dismantling of galvalume aluminium zinc coating GI based plain or corrugated steel sheets of any thickness in roofing all as specified and as directed.

S&F Pre- painted Galvalume Aluminium Zinc coating GI based corrugated steel sheets 0.5 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and as directed.

M&L for roof tiles, mangalore pattern class 'AA', interlocking at side joints, laid dry complete all as specified and as directed.

M & L for ridge or hip tiles to suit Mangalore pattern or roofing tiles, bedded and jointed in cement mortar 1:3 in small patches including dismantling existing ridge tiles complete all as specified and as directed.

Demolition of cement concrete of any description and any position all as specified and as directed.

M&L for plain cement concrete type B-0 ,1:2:4 using 12.5 mm graded stone aggregate as in coping,holdfast,cills,steps,water troughs and the like including weathering ,slightly rounded or chamfered angles and throating etc all as specified and as directed.

M&L for plain cement concrete type C-0 ,1:3:6 using 12.5 mm graded stone aggregate as in roof kerbs or mud stops rounded or chamfered edges all as specified and as directed.

M &L for applying two coats of water proofing coating system of approved make over a coat of respective primer including preparation of plaster surface by complete removal of existing treatment including filling of crack with respective crack filler all as per manufacturers instructions complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation) or insulation boards /slab /blankets of any description and thickness including frame/grid of any description all as specified and as directed

M&L for anodised aluminium snap grid (minimum 15 microns anodisation) of size 605 x 605 mm with anodized aluminum angle of size 40mm x 25mm x 2mm thick weighing 0.36 Kg per running meter and anodized aluminum main and cross T of size 36.50 x 23.50 x 1.50 mm thick weighing 0.254 Kg per running meter and 23.50 x 23.50 x 1.50 mm thick weighing 0.202 Kg per running meter respectively for false ceiling all as specified and as directed

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia, 40mm long suitable for size of snap grid 605 x 605 mm complete all as specified and as directed

M&L for gypsum board 12mm thick in ceiling fixed with screws on snap grid all as per manufacturer instructions.

Demolition of stone slabs and tiles of any description or thickness in floors,aprons etc laid bedded and pointed in any mortar all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing all the rubbish ete all as specified and as directed.

M&L for screed bed or bedding layer 15mm thick in cement mortar 1:4 to receive topping layer such as tilling etc complete all as specified and as directed

M & L for rendering 10 mm thick in cement mortar 1:3 on fair faces of concrete/brick work surfaces finished fair and even without using extra cement to receive tiles complete all as specified and as directed.

M&L for screed bed or bedding layer 20 mm thick in cement mortar 1:6 to receive topping layer such as tilling etc complete all as specified and as directed

M & L for non skid ceramic coloured tiles (Ist quality) 7 to 8 mm thick (Square/rectangular), area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm as in floors etc set and jointed in neat grey cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic coloured tiles (Ist quality) of size 300 x 200 x 6 to 7 thick on vertical surface such as skirting,dado and rises to steps etc set and jointed in neat grey cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and as directed

M&L for machine cut kota stone slab flooring 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed Note:Size of kota stone shall not be less than 60cm x 60cm

M & L for non skid ceramic coloured tiles (Ist quality) 7 to 8 mm thick (Square/rectangular), area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm as in floors etc set and jointed in neat grey cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 22 here in before but in vertical surfaces such as skirting, dado etc complete all as specified and as directed

Taking up or down 15 mm bore steel tubing and connections all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections all as specified and as directed

Taking up or down 25 mm bore steel tubing and connections all as specified and as directed

S & F 15 mm bore UPVC pipes of pressure rating 10 Kgf/ Sqcm fixed to walls ,ceiling or laid in floors etc all as specified and as directed.

S & F 20 mm bore UPVC pipes of pressure rating 10 Kgf/ Sqcm fixed to walls ,ceiling or laid in floors etc all as specified and as directed.

S & F 25 mm bore UPVC pipes of pressure rating 10 Kgf/ Sqcm fixed to walls ,ceiling or laid in floors etc all as specified and as directed.

S & F in repair 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, ISI marked (Minimum weight 210 gms), screwed & suitable for iron pipe 20 mm bore, all as specified and as directed.

S&F in repair 20 mm dia gun- metal globe or gate valves, with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair 25 mm dia gun- metal / bronze gate valve ISI marked with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floor and pavings not exceeding 15 cm thick (below or above ground level) and removing all the rubbish as directed by Engineer-in-charge complete all as specified and as directed

M&L for 75mm thick PCC type-C2 , 1:3:6 using 40 mm graded stone aggregate as in plinth protection and finishing the concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 100 mm thick PCC type-C2 , 1:2:4 using 40 mm graded stone aggregate as in hard standing / floor and finishing the concrete surface even and smooth without using extra cement complete all as specified and as directed.

Taking down wooden/PVC/FRP chowkats or frames with shutters (without taking off shutter from the frame ), area exceeding 1.5 sqm but not exceeding 4 sqm each including making good disturbed portion to match with adjoining surfaces and offering credit as per schedule of credit all as specified and as directed.

All as per item No 36 here in before but not exceeding 1.5 sqm all as specified and as directed.

Taking down wooden door / window /CB shutters of any description, area exceeding 1 sqm but not exceeding 2 Sq m each and offering credit as per schedule of credit all as specified and as directed.

All as per item No 38 here in before but not exceeding 1 sqm each all as specified and as directed.

Refixing shutters of any description of area exceeding 1 sqm and not exceeding 2 sqm each all as specified and as directed.

All as per item No 40 here in before but not exceeding 1 sqm each all as specified and as directed.

Refixing in repairs chowkhats or frames of area exceeding 1.5 sqm but not exceeding 4 sqm each all as specified and as directed.

M&L for second class hard wood (Sal) plain solid, straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints all as specified and as directed.

S & F Factory made PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition complete all as specified and as directed

S&F 35mm thick plain framed second class hard wood panelled factory made shutters (two panel) with lock rail and panel of 9mm thick BWP commercial ply with size of rail and stiles as per IS 1003 (part-1), kin seasoned and chemically pressure treated all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified in drawing on sl page No 156 of SSR 2010 part –II complete and as directed

S & F 35 mm thick plain factory made second class hardwood skeleton shutters ,open rebated and prepared to receive glass/gauge etc.(without sash bar) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass / gauge etc., sizes of members of shutters as specified in SSR Part-I kin seasoned and chemically pressure treated all as specified and as directed .

M&L for 18 mm/ 19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in kitchen cabinets/shutters fixed with screws as in repairs all as specified and as directed.

M&L for 12 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in kitchen cabinets/shutters fixed with screws as in repairs all as specified and as directed.

S&F Powder coated aluminium window/ventilators shutter including frame, any type sliding or openable with frame, & other similar work etc. fabricated by using the standard section including necessary arrangements to receive 4mm thick glass or wire mesh with aluminium channel beading & stainless steel screws including the cost of rubber gasket/rubber beading etc. complete including necessary handles, roller wheels, hinges etc complete all as specified and as directed. Note :- Weight of aluminium section shall be measured exclusive of all fittings fixtures, hinges, handle, bolts, rubber gasket/rubber beading and locking arrangements.

S & F Aluminium powder coated (minimum thickness of powder coated 50 micron) window / ventilator shutters, sliding type without sash bars,aluminium section weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium snap beading, screws etc. complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed

S & F Mild steel framed work such as grills, gratings or guard bars etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars etc conforming to fe 410-0 or fe 310-0 ,complete all as specified and as directed

S&F Aluminium grills of DG 104 (10 mm) powder coated of approved make all as specified and as directed

S&F 40 mm dia ,cupboard knobs fixed with nut,screw and washer of powder coated aluminium bright finished all as specified and as directed

S&F Aluminium hasp and staple size 100 mm powder coated with hinge pin including bolt to hinge plate and fixed with screws all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames glazed with putty or fixed with beads all as specified and as directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with wooden beading not exceeding 0.5 Sqm in each pane all as specified and as directed.

M&L for 4mm thick figured glass, pin head type and glazing with wooden beading not exceeding 0.5 Sqm in each pane all as specified and as directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm and fixed with aluminium wire staples all as specified and as directed.

S&F in repairs aluminium alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm and fixed with aluminium wire staples all as specified and as directed.

S&F Butt hinges 75mm sizes, extruded aluminium alloy with galvanised mild steel hinge pin anodised, type C-21 all as specified and as directed.

All as per item No 62 here in before but 100mm size, type B-21 complete all as specified and as directed

All as per Item No 62 here in before but 125mm size complete all as specified and as directed

S&F Aluminum alloy sliding door bolt 300 mm long and not less than 12mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and as directed.

S&F Aluminum alloy sliding door bolt 250 mm long and not less than 12mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and as directed.

S&F Aluminium barrel tower bolts of extruded section 200mm long complete all as specifed and as directed.

All as per Item No 67 herein before but 150 mm long complete all as specified and as directed

All as per Item No 67 herein before but 100 mm long complete all as specified and as directed

All as per Item No 67 herein before but 75 mm long complete all as specified and as directed

S&F Extruded aluminum alloy handles, fabricated type and powder coated, 100mm size all as specified and as directed

All as per Item No 71 herein before but 75mm complete all as specified and as directed

All as per Item No 71 herein before but 150mm complete all as specified and as directed

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece fixed in floor overal length of plate 140mm complete all as specified and as directed

S&F Mild steel articles such as bands, straps, supports or stays for rain water, holdfasts etc conforming to Fe- 410- WA (Gde E-250) all as specified and as directed.

M&L for plain fillets second class hard wood bull nosed,splayed,chamfered or rounded on one edge or face sectional area exceeding 3sqcm and not exceeding 6 sqcm all as specified and as directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc all as specified and as directed.

M&L for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 150 mm bore including taking down of existing one all as specified and as directed.

M&L for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 110 mm bore all as specified and as directed.

M&L for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 75 mm bore all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10cm width or girth including preparation of surfaces all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on old steel surfaces of any description over 10cm width or girth including preparation of surfaces all as specified and as directed.

M & L for providing and injecting emulsion for post construction anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion at the rate of 2.25 litres per linear meter including drilling holes and plugging the holes with cement mortar & matching the existing surface etc complete all as specified and as directed.

M & L for providing and injecting emulsion for post construction anti termite treatment for soil under existing floors using chemical emulsion at the rate of one litre per hole, 300mm apart including drilling 12 mm dia holes and plugging the holes with cement mortar (1:2) etc to match with existing floors complete all as specified and as directed.

M & L for providing and injecting emulsion for post construction anti termite treatment at points of contacts of wood with masonry / concrete surfaces using chemical emulsion mixed with oil or kerosine at the rate of 0.5litres per hole including drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and plugging the holes with cement mortar (1:2) etc to match with existing surface complete all as specified and as directed.

M & L for providing and injecting emulsion for post construction anti termite treatment along the external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per square metre on vertical surfaces pf the sub structure to d depth of 300 mm including excavating channel along the wall and rodding etc all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10cm width or girth including preparation of surfaces all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces of wall/ceiling and likes including racking out joints, hacking for keys scrubbing down with water etc all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick/cement/stone surfaces and finishes the surfaces even and smooth without using extra cement all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on brick/cement/stone surfaces and finishes the surfaces even and smooth without using extra cement including mixing with liquid WPC on top 5 mm thick only all as specified and as directed. Note: WPC shall be measured and paid separately

Supply only liquid water proofing of approved make ,200 ml per bag of cement all as specified and as directed.

M&L for applying two coats of colour wash over a coat of white wash including preparation of newly plastered surfaces all as specified and as directed.

M&L for applying two coats of acrylic emulsion exterior paint (anti fungal paint-APEX or Equivalent) over a coat of acrylic emulsion primer including preparation of surface of any description all as specified and as directed.

M&L for chisel the crack to a "V" groove of 5 mm x 5 mm clean the groove to remove all loose laitance and wash with apply crack filler of approved make with a putty blade all as specified and as directed.

M&L for filing of gas between window and wall with silicon sealant over cement mortar 1:1 all as specified and as directed

Removing loose concrete/plaster upto sound stratum of ceiling chajjas ,columns and beams and cleaned the surfaces with water using water jet etc all as specified and as directed.

M&L for applying one coat of rust remover chemical of approved make on old rested reinforcement after necessary preparation of surfaces by brush application all as specified and as directed.

M&L for priming the old/new steel reinforcement bars with one coat of zinc primer of approved make by using brush application all as specified and as directed

M&L for previously prepared steel surface and apply concrete penetrating corrosion inhibitor of approved make .After few minutes wipe the concrete/steel surface with moist cloth to remove residual materials all as specified and as directed

Bonding the exposed surface with one coat of SPR latex of approved make all as specified and as directed

M&L for applying two coats of oil bound distemper over a coat of alkali resistant primer on new plastered surfaces including necessary preparation of surfaces, complete all as specified and as directed.

M&L for polymer modified mortar 20-50 mm thick as required at site prepacked,single component structural grade mortar of approved make including fair finishes to surfaces all as specified and as directed.

Disconnecting existing water tanks up to 500 Ltr capacity, setting aside for repairs, cleaning, etc and hoisting if required reconnecting and refixing in position including cleaning all scales and dirts from inside of tank using bleaching powder and washed with water all as specified and as directed.

All as per Item No.103 here in before but for 1000 Ltr capacity all as specified and as directed.

All as per Item No.103 here in before but for 2000 Ltr capacity all as specified and as directed.

S&F in repairs rotational moulded polytylene water storage tanks of 300 litres capacity (cylindrical vertical with closed top) double layer construction , ISI marked,provision of tank neeple including dismantling and removing the existing tanks,dismantling and hoisted and fixed in position reconnection of existing pipe lines all as specified and as directed.

All as per Item No.106 here in before but for 500 Ltr capacity all as specified and as directed.

All as per Item No.106 here in before but for 1000 Ltr capacity all as specified and as directed.

All as per Item No.106 here in before but for 2000 Ltr capacity all as specified and as directed.

S & F PVC water tank cover for 500 Ltrs rotational moulded polytylene water storage tanks all as specified and as directed

S & F PVC water tank cover for 1000 Ltrs rotational moulded polytylene water storage tanks all as specified and as directed

S & F PVC water tank cover for 2000 Ltrs rotational moulded polytylene water storage tanks all as specified and as directed

Treatment of sunken floor slab comprises of the following specifications and all as specified and as directed :- (i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope (ii) Rendering of uneven surfaces with 5 mm thick cement mortar 1:4 mixed with integral water proofing compound @ 3% by weight of cement consumed. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting to be carried out (WPC shall be measured and paid separately) (iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.

(v) Applying two coats of polymer modified cementious water proof coating as per manufacturers instruction to bottom and vertical sides up to finished floor level (+100mm height). The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (This item shall be measured and paid separately ) (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick cement mortar 1:4 mixed with integral water proofing compound @3% weight of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately ) Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of PMG and record for each sunken slab shall be maintained. The treatment shall be carried out by authorized applicators of chemicals. Cost of testing is included in the rates quoted above. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint (Painting shall be measured and paid separately)

Supply only Integral Water proofing compound complete all as specified and as directed.

M&L for applying two coats of polymer modified cementious water proof coating as per manufacturers instruction to bottom and vertical sides up to finished floor level +100 mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed.

Taking down aluminium sliding window shutter not exceeding 1 sqm from track / tube by removing frame / track and refixing the same after replacing damaged/perished/rusted gauge /wire mesh etc all as specified and as directed

Taking down existing aluminium doors/windows and refixing after tightening loose screw including replacement of unserviceable screw all as specified and as directed

M&L for replacement of damaged aluminium beading of aluminium doors windows with new beading all as specified and as directed

M&L for replacement of unserviceable rubber packing of aluminium door & window including taking down carefully glass panels and refixing the same all as specified and as directed

S & F in repair double action floor spring hydraulically regulated made up minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty including taking down un-serviceable floor spring complete all as specified and as directed

S&F 5mm thick tinted glass in aluminium doors & windows with rubber packing including hacking out old broken glass ( any thickness, size from aluminium beading ) complete all as specified and as directed

S&F in repair 12 mm thick particle board medium density ,flat pressed, single layer type or three layer type with BWR type adhesive, fixed in aluminium frame complete all as specified and as directed

S&F in repair mortise lock vertical type & 4- levers of 100mm brass body with two keys complete all as specified and as directed

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring overal length of plate 140mm complete all as specified and as directed

S&F in repair aluminium (Die cast ) body door closer hydraulically regulated designation No-3 universal type suitable for door shutters of 85 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed