D1/2024-2025

Amount

Furniture Details

PPO Unitized T25+1 Table Providing, supplying and placing of PPO Unitized T25+1 Table Size of main table should be 1500 mm in width, 600 mm in depth and 750 mm in height with end return unit of 900 mm witdth, 450 mm depth and 750 mm height with matching corner flawless design. Main Worktop-Made of 18mm Thick Pre-laminated board (PLBof High grade and approved shade confirming from engineer, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Return Worktop-Made of 18mm Thick Pre-laminated board (PLBof High grade and approved shade confirming from engineer, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel-Made of 18mm Thick Pre-laminated twin board (PLTof High grade and approved shade confirming From engineer, Edge banded with matching 2 mm thick PVC lipping. Legs-Cube legs are fabricated from MS ERW Tube of 50 mm x 50 mm x 1.2mm thick and 50 mm x 50 mm x 1.2 mm thick . At the top surface of leg, support brackets of 3 mm thick HR are welded for fixing worktop. These are welded togesther by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, Cross Members-Cross Members in Unitized T-2 Desk Series are made from 50mm X 50mm X 1.2mm thick ERW tube . These are coated with 50 micron epoxy polyester coating.Cross Members are assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Access Flap-Soft closing access flap is used in Unitized T-2 Desk Series. Provision for standard size of 8 module electrical (Anchor Romais offered. Access flap is made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power Box-Power box made with 0.8 mm thick CRCA , with switch plate (8 Module cutout provision for Anchor Roma). This is fixed with worktop along the depth at Access Flap position. Integrated Hinge Door Storage with Drawer-Made of 18mm Thick Pre-laminated twin board grade and approved shade confirming From engineer, Edge banded with matching 2 mm thick PVC lipping. Door is fixed with slide on hinges and handle is provided for ease of opening. Drawer is provided with ebco metabox slide and lock for security.

TABLE @ 1800LX 900DX740Ht. Providing, supplying and placing of Main Table Finness 6030 table Table size shall be 1800 Width mm x 900 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board PPB Clad with both sides. Edge Sealed with 2 mm thick PVC beading.

ERU PPO ERU 1550LX 450DX705HT. Providing, supplying and placing of ERU PPO ERU ERU size shall be 1550 Width x 450 Depth x 705 Height.The top of Finesse ERU shall be 25 mm thick plain particle board Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board . Edge sealed with 2 mm thick PVC Beading.

PPO Aristo Table 2350x2350x750 mm Providing, supplying and placing of Main Table, ERU & pedestal. PPO Aristo Table ARISTO TBL 2350 RH RU 1200 PDL 2350x2350x750 mm Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming from engineer Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25 mm thick pre-laminate board . Modesty Panel Made of 18mm thick pre-laminate board confirming from engineer. Under structure Made of 25mm Thick Pre-laminated twin board and approved shade confirming from engineer, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 18mm Thick Pre-laminated twin board confirming , Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick pre-laminate board confirming Pedestal construction is BOX-BOX-FILE type Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

MID BACK CHAIR for staff. Providing, supplying and placing of briyo mid back chair SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (Wx 58.0 cm. (H). SEAT SIZE 47.0 cm. (Wx 48.0 cm. (D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3. TUBULAR FRAME : The powder coated DFT 40-60 microns tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene.

Visitor chair staff Providing, supplying and placing of Visitor Chair pearl visitor as per order SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort. BACK SIZE: 49.5cm. (WX 45.5cm. (H). SEAT SIZE: 49.5cm. (WX 43.0cm. (D). HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should be scratch and weather resistant tant. The armrests should be fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel. FIXED TYPE mechanism: The fixed type mechanism should be without back tilt. TUBULAR UNDERSTRUCTURE: The understructure should be made of Ø2.54 2.54±0.03cm.x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 45.0cm. Height -84.0cm. Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-58.0 cm.

High back chair for N.T. Providing, supplying and placing of High Back Chair PPO Unitized T25+1 Table SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back Executive chairs onlyfor extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (Wx 82.0 cm. (H) SEAT SIZE 53.5 cm. (Wx 51.0 cm. (D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf for 25% compression. ARMRESTS (THRILL PLUS CHAIR: The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon.· Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · Any position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY THRILL PLUS: The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM.

High back chair Providing, supplying and placing of High Back Chair La Selva leather chair as per order SEAT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HRPolyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (Wx 49.2 cm. (D) BACK SIZE : 47.5 cm. (Wx 77 cm. (D) ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • Seat/back tilting ratio of 1: 2 SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Polypropylene.

Visitor Chair,SDO and Tahsildar cabins Providing, supplying and placing of Visitor Chair Briyoo visitor chair as per order SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressedplywood measured upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contouredlumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area. MID BACK SIZE 47.5 cm. (Wx 58.0 cm. (H). SEAT SIZE 47.0 cm. (Wx 48.0 cm. (D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam is moulded withdensity = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated DFT 40-60 microns tubular frame iscantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair WIDTH (W): 61.4 CM. DEPTH (D): 64.5 CM. HEIGHT (H): 89.5 CM. SEAT HEIGHT (SH): 46.5 CM.

High back chair for computer room Providing, supplying and placing of High Back Chair Motion Highback Chair as per order SEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Back Size : 45.5 cm. (/W/x 53.0 cm. (H Seat Size : 48.5 cm. (Wx 49.0 cm. (D HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam used in seat and back cushion is moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf for 25% compression. TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "S" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted which should be inbuilt in seat base and the tension (return forceshould be user weight dependent. ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide: The height adjustment feature should be button operated having adjustment of 6.6±0.5cm. The Armrest Top should be made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. PNEUMATIC HEIGHT ADJUSTMENT: The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm . PEDESTAL ASSEMBLY: The pedestal should be injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors . TWIN WHEEL CASTORS :5 nos. twin wheel castos are injection moulded in Poly-amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal.

Mid back chair for Auditorium dias Providing, supplying and placing of Conference Mid Back Chair Legacy PPO Conference Chair SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(WX 64.5cm.(H) SEAT SIZE: 51.0cm.(WX 48.0cm.(D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS:The armrest top should be made of moulded polyurethane (P.Uand mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FRONT PIVOT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • Any position locking with anti-shock feature. • Seat back tilting ratio of 1:2. FIXED BACKREST :The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment. PNEUMATIC HEIGHT ADJUSTMENT :The pneumatic height adjustment has an adjustment of 10.0 ±0.3cm. PEDESTAL ASSEMBLY:The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0 ±0.5cm. Pitch-center dia. (76.0 ±1.0cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.2 to max 57.2cm. Height - min 96.5 to max 106.5 cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.

HIGH BACK CHAIR FOR VIDEO COFERENCE ROOM Providing, supplying and placing of Conference High Back Chair Legacy conference PPO HB chair SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(WX 76.0cm.(H) SEAT SIZE: 51.0cm.(WX 48.0cm.(D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS:The armrest top should be made of moulded polyurethane (P.Uand mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FRONT PIVOT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • Any position locking with anti-shock feature. • Seat back tilting ratio of 1:2. FIXED BACKREST : The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment of 10.0 ±0.3cm. PEDESTAL ASSEMBLY:The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet. chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0 ±0.5cm. Pitch-center dia. (76.0 ±1.0cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.2 to max 57.2cm. Height - min 107.8 to max 117.8cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.Gaslift - Gaslift should have minimum 100 mm stroke length and should be BIFMA Compliant and tested with 122kg on seat, for 60,000 cycles rotation @ 5-10 rotation / min. Base - Base should be Aluminium die cast base and should be BIFMA compliant and tested for 1450 kg of load. Castors- Castors should be twin wheel castors having 60 mm dia.

High back chair for video conferencing Providing, supplying and placing of High Back Chair PPO Chill LC HB SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back Executive chairs onlyfor extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (Wx 82.0 cm. (H) SEAT SIZE 53.5 cm. (Wx 51.0 cm. (D) HIGH RESILIENCE (HRPOLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · Any position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM.

Public seating Chair Providing, supplying and placing of three seater waiting chair. It should be made up of black powder coated rectangular M.S.ERW tube having 8.0 ± 0.03 cm x 4.0 ± 0.03 cm x 0.2 ± 0.014 cm size. It should be Powder coated made of cold rolled steel with 0.12 ± 0.013 cm thinkness. It should be powder-coated perforated shell made from cold rolled M.S. sheet 0.14+/-0.013cm thickness.The Side Bar should be made of Powder Coated solid steel 3.0+/-0.03cm * 1.2+/-0.3cm with fluting and plastic inserts. The Shell should be assembled on the Cross Beam with help of M8 Bolts (Per Seat - 8 nos. Seat to Bracket and 4nos. Bracket to Cross Beam). Overall Dimensions Seat Height - 40.0cm, Height - 67.5 cm, Width & Depth of Chair as - Width-163.0cm and Depth-57.0 cm.

Steel Almirah 916mm(W) x486mm(D)x1981mm(H) Providing, supplying and placing of storage unit. steel almirah storewel plain as per order steel almirah storewel plain as per order Overall size of 916mm(W)x486mm(D)x1981mm(Hwith welded construction. It should have the shelf thickness of 0.8 mm, Back thickness of 0.7mm, Door thickness of 0.8mm (high yield strengthand all other components shall have a thickness of 0.5mm. These components shall be made of CRCA ‘D’ grade high yield strength :513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Slotted Angle Rack Supply and installation of slotted angle rack Slotted angle- Slotted angle is made up 1.2mm thick CRCA sheet confirming the IS grade coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 50 to 60 microns. Angle length is equivalent to the height of the storage which is approx. 2100mm or 1830mm Shelf-Is made up of 0.6mm CRCA sheet confirming . All the four edge is having a bend of 25mm. Shelf is supported by T-Hat in the middle portion. T-hat is made up of 0.6mm CRCA sheet confirming Each shelf is having loading carrying capacity of 14kg UDL and total load carrying capacity of unit is 30kg UDL.Finish- The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder. It involves an Oxsilan pre-treatment consisting of Hot water degreasing, cold water rinse I & cold water rinse II, iron phosphate, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5microns. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Fasteners:- Assembly is done with the help of M8 NUT nuts & HEX BOLT M8 X 16.

Book case Providing, supplying and placing of Bookcase. Book Case as per order Overall size of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.5mm high yield CRCA and other components from 0.6mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 50 Kg. The It shall have 18mm PLB Top straight edge with PVC lipping. The finishing shall include Epoxy powder coated to the thickness of 80 microns (+/- 10).

Auditorium chair Providing, supplying and placing of cafeteria Chair PPO unwind MS Chair The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (Wx 53.2 cm. (DBACK SIZE : 51.6 cm. (Wx 40.5 cm. (HThe powder coated DFT 50±10 microns welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame. Overall Dimensions of Chair Seat Height - 45.0 cm Height - 84.5cm Width-52.5 cm and Depth-55.8 cm

Video Conference Table Providing, supplying and placing of conference table Mingle Conference Table 22seater Worksurface : Made of 25mm Thick Pre-laminated and approved shade Edge banded with matching 2 mm thick PVC lipping. Understructure : It consist of 18mm Thick Pre-laminated twin board of grade and approved shade Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Modesty Panel : Made of 18mm Thick Pre-laminated twin board grade and approved shade conforming Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA 513,epoxy polyester powder coated (DFT 40-60 microns) Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 micronsis used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.

Computer table Providing, supplying and placing of office Table PPO T20+1 Table Worktop-Made of 18mm Thick Pre-laminated board approved shade confirming From engineer, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of grade and approved shade confirming to, Edge banded with matching 2 mm thick PVC lipping. Legs-Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 50 mm x 50 mm x 1.2 mm thick. At the top surface of leg, support brackets of 3 mm thick HR are welded for fixing worktop. These are welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members-Cross Members in Unitised T-2 Desk Series are made from 50mm X 50mm X 1.2mm thick ERW tube (:7138). These are coated with 50 micron epoxy polyester coating.Cross Members are assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Access Flap-Soft closing access flap is used in Unitized T-2 Desk Series. Provision for standard size of 8 module electrical (Anchor Romais offered. Access flap is made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power Box-Power box made with 0.8 mm thick CRCA , with switch plate (8 Module cutout provision for Anchor Roma). This is fixed with worktop along the depth at Access Flap position

Pedestal NOVA FREE STANDING PEDESTAL WITH SIZE 390W X 435D X 646HT, 1DR = 1 BOX + 1 FILE, CENTRAL LOCKING. All Dry film/ coating thickness, Finish, Gloss 60°, Colour retention, Scratch hardness, Impact resistance test, DFT measurement, Salt spray test, Adhesion Cross cut test. All item are made of prelaminated partical board. with 3 drawersand as directed and apporved by Consultant and Engineer in charge.

Vertical blinds Providing and Fixing Vertical Blinds of approved and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)

Sintileit Technologies

NISHAD INDUSTRIES