PROVN OF OR LIVING BARRACK WITH ALLIED INFRA AT KIARI AND PROVN OF 01TOILET BLOCK WITH ALLIED INFRA AT NYOMA UNDER GE 860 EWS

Amount

Surface dressing n exc 15 cm deep in soft /loose soil complete all as specified and directed by Engr in charge.

Excavating in post holes (or similar holes) each n. exc 0.5 cum, getting out, returning, filling in and ramming earth, broken rubble mixed with earth around, in layers not exc 25 cm complete all as specified and directed by Engr in charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard /dense soil complete all as specified and directed by Engr in charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr in charge.

M&L for Cement concrete type D2 1:4:8 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engr in charge.

M&L Cement Concrete Type-B1 (1:2:4) using 20mm graded crushed stone aggregate as in foundations, including rafts, footings complete all as specified and directed by Engr in charge.

M&L for reinforced cement concrete (Nomonal mix) 1:2:4 (using 20mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and as directed.

S&F Mild steel TMT bars 10 mm dia and over Fe-410 W(Gde E 250) cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and directed by Engr in charge.

M&L mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.

S&F steel work in tubular/Rectangular/Square hollow section trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 complete all as specified and directed by Engr in charge.

M&L for Pre-cast cement concrete block masonry type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed by Engr in charge.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr in charge.

M&L 75 mm thick in PCC type C1 1:3:6 (using 20 mm graded aggregate crushed stone aggregate) as in plinth protection laid in alternate bays (not exc 2 Sqm each) finishing even smooth at top without using extra cement and providing joints throughout the thickness of plinth protectio, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed by Engr in charge.

M&L for PCC 100 mm thick 1:2:4 type D2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed by Engr in charge.

M&L for coloured jointless Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 complete all as specified and directed by Engr -in-Charge.

M&L for Glazed ceramic tiles450x300x7mm thick coloured/shaded as in vertical surfaces such as skirting dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface with 10 mm thick rendering (1:4)

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr in charge.

S&F Factory made shutter 35 mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed by Engr-in-charge.

S&F 30mm thick Second class hard wood Glazed and skeleton windows,ventilators open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc.sizes of members of shutters as specified in SSR Part I, Section 8 Clause 8.24(a) complete all as specified and directed by Engr in charge.

S&F 3.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr in charge.

S&F Figured glass, pin head type 3 mm thick, confirming to SI-5437 (1969) and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed by Engr in charge.

M&L PCC type B-1 1:2:4 (using 20 mm graded crushed stone aggregate) for fixing hold fast complete all as specified and directed by Engr in charge.

S&F MS flat iron of size 25x3 mm as in hold fast conforimg to Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr in charge.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed by Engr in charge.

Rendering 15 mm thick on fair faces of brick wall or cement concrete surface in cement mortsr 1 :4 finished even smooth without using extra cement complete all as specified and directed by Engr in charge.

S&F 100 mm size extruded alluminium alloy with galvanised mild steel hinge pin type C-21 complete all as specified and directed by Engr in charge.

S&F Aluminium anodised, barrel tower bolts of extruded section with 150 mm long bolt and fixed complete all as specified and directed by Engr in charge.

S&F Aluminium handles, cast type, anodised 125 mm size complete all as specified and directed by Engr in charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm long complete all as specified and directed by Engr in charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 150 mm long complete all as specified and directed by Engr in charge.

S&F 0.50 mm thick Pre- painted galvalume aluminum zinc coating GI based corrugated in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as directed by Engr-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts complete all as specified and directed by Engr in charge.

S&F Viterous China wash urinal, half stall type, white complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement incl 32mm dia PTMT waste coupling, 32mm dia PVC waste pipe and urinal spreader complete all as specified and as directed.

S&F Viterous China wash hand basin with pedestal coloured, flat back of 550 x 400 mm including brackets, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of 750mm long complete all as specified and directed.

S&F vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of lime concrete including P/S traps complete all as specified and directed by Engr in charge.

S&F PVC (Plastic polymer Cistern) low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle etc and S & F of 32 mm dia PVC flush pipe of suitable length and making all connection complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and jointed in position all as specified in SSR Part-I (1000 ltr capacity) and providing all necessary fittings for connecting with pipe line, metal lockable cover complete all as specified and directed by Engr in charge.

S&F 16 mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UN stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threated polypropylene random fittings laid in trenches etc complete all as specified and directed by Engr in charge.

S&F 20 mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UN stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threated polypropylene random fittings laid in trenches etc complete all as specified and directed by Engr in charge.

S&F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr in charge.

S&F 20 mm bore ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr in charge.

S&F 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr in charge.

S&F 15mm bib taps, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engr in charge.

S&F brass chromium plated tubular towel rail 20mm dia 600 mm long fixed complete all as specified and as directed.

Supply and laying 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

Supply and laying 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

M&L for PVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm fixed complete all as specified and directed.

S&F 75 mm dia PVC floor trap , plain with grating including jointing with solvent complete all as specified and directed by Engr in charge.

S&F angle/stop valves 15mm bore (for iron pipe) fancy type PTMT any colour screwed down high pressure with butterfly handle screwed both ends complete all as specified and directed by Engr in charge.

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes etc. with riveted, bolted or welded attachment confirming to Fe 410-W (Gde E-250), complete all as directed by Engieer-in-charge.

Mild steel bolts neck exc 10 mm dia and n exc 15 mm dia, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each scre-wed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long complete all as specified and directed by Engr in charge.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and treating with two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified and directed by Engr in charge.

Preparing newly plastered surfaces of wall and applying two coats of cement base paint with one coat of primer complete all as specified and directed by Engr in charge.

Preparing newly plastered surface of wall of any description and applying two coats of distemper oil emulion, with one coat of primer complete all as specified and directed by Engr in charge.

Prepration of new wooden or wood based Surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr in charge.

M&L for plywood Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 6 mm thick ( 5 Nos of ply) fixed with nails to timber frame work complete as in walls complete all as specified and directed by Engr in charge.

M&L for plywood Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 4 mm thick ( 3 Nos of ply) fixed with nails to timber frame work complete as in ceiling complete all as specified and directed by Engr in charge.

M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 6 Sq cm n.exc 13 Sq cm secured with nails or brads complete all as specified and directed by Engr in charge.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by Engr in charge.

Excavating over areas, exc 1.5 m and n.exc. 3.00m deep and getting out in hard/dense soil complete all as specified and directed by Engr in charge.

M&L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, build in cement mortar 1:6 complete all as specified and directed by Engr in charge.

M&L for Walling of random rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar work complete all as specified and directed by Engr in charge.

M&L for reinforced cement concrete Type B1 1:2:4 using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and as directed.

M&L for formwork Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in cover slab for manholes set in CM 1:4 including necessary form work complete all as specified and directed by Engineer in Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms complete all as specified and directed by Engr in charge.

M&L plain cement concrete 1:3:6 Type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW pipe complete all as specified and directed by Engr in charge.

Supply and laying 150mm dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr in charge.

M&L Rendering 15mm thick in CM 1:4 on fair faces of stone surface work with water proofing compound @ 3% weight of cement including finishing the surface even and smooth without using extra cement. Note : WPC shall be measured and paid seperately.

Supply only water proofing compound complete all as specified and directed by Engr in charge.

M&L for broken boulders stone n. exc. 80 to 100mm of gauge in loose filling complete all as specified and directed by Engr in charge.

M&L for Cement Concrete type D-2, 1:4:8 (using 20 mm graded crushed stone aggregate) 100mm thick as in sub base complete all as specified and directed by Engr in charge.

M&L for 40mm thick Cement Concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in floor sub base complete all as specified and directed by Engr in charge.

M&L for coloured non-skid ceramic tiles 7 to 8 mm(square/rectangular) rea of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc 15 mm thick cement mortar screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engr-in-charge.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr in charge.

S&F 300 mm aluminium alloy anodised sliding door bolt with hasp, staple complete all as specified and directed by Engr in charge.

M&L 4 mm thick glass panes ordinary quality and glazing with oil putty in square n .exc 0.50 Sqm in each pane complete all as specified and directed by Engr in charge.

M&L for preparing newly plastered surface of walls and applying two coast of white wash complete all as specified and directed by Engr in charge.

S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and directed by Engr in charge.

S&F 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr in charge.

M&L for PCC 1:3:6 type C-2 (Nominal Mix) using 40 mm graded stone aggregate as in foundation filling mass concrete and similar work complete all as specified and as directed.

M&L TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr in charge.

M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I (2009) complete all as specified and directed by Engr-in-Charge.

M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110 mm complete all as specified and directed by Engr in charge.

M&L Point wiring with 1.5 Sq.mm. FRLS PVC insulated unsheathed copper conductor multi stranded 1100 Volts grade, ISI marking drawn through and including non metallic PVC rigid concealed conduit and conduit accessories medium grade, ISI marked, including modular metal flush box with and including modular white cover plate with frame for mounting modular switches/sockets/fan regulators etc. including one run of 1.5 Sq.mm. PVC insulated unsheathed copper cable for earth continuity, connected to earth dolly, for One light point controlled by one switch or One fan (ceiling fan/exhaust fan/wall mounted/air circulator) point controlled by one switch or one 3 pin socket outlet 5 Amps on independent board on independent board complete all as specified and as directed by the Engineer-in-Charge.

Description all as per Srl item No. 89.00 here-in-before but for one 3 pin socket outlet 15 Amps on independent board with 4 Sq.mm. FRLS PVC wire and one run of 2.5 Sq.mm. copper cable for earth continuity.

Description all as per Srl item No. 89.00 here-in-before but for one 3 pin socket outlet 5/6 Amps on independent board with 1.5 Sq.mm. FRLS PVC wire and one run of 1.00 Sq.mm. copper cable for earth continuity.

Supply and fix Switch piano flush type single pole, one way 5 Amp complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed by the Engineer-in-Charge.

S&F Inverter LED lamp, 6500K,900lm in white colour of 9 Watt base cap B-22 with poly carbonate difusser and aluminium heat sink ,complete all as specified & directed.

Supply and fix Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Switch socket outlet combination 3 pin, 5 Amp, flush type complete all as specified and as directed at site by the Engrs-in-Charge.

Supply and fix of Switch socket outlet combination, 2 in 1, 3 pin 5 and 15/16 Amp, piano flush type, 240 volts, complete all as specified and as directed at site by the Engrs-in-Charge.

S&F energy efficient LED tube light fitting (Mirror optic) with tube 1x20 Watt, 240 Volts, 50 Hz, luminous efficiency 100 Lumen per Watt, CRI>80, PF>0.9, surface mounted, decorative ultra slim square profile LED lighting fixture etc. with extruded polycarbonate environmental friendly, energy efficient ready to use pack complete with mounting bracket etc. including connecting up with 1.0 Sq.mm. 3 core flexible copper conductor cable complete all as specified and as directed by the Engineer-in-Charge.

S&F LED building security light fitting 36 Watt, luminous efficiency 100 Lumen per Watt, CRI>80, PF>0.9, new generation energy saving & environmental frindly long life made up of pressure die cast aluminium housing with high efficient LED as lighting source and lens embedded PC cover having bottom opening seperate driver compartment with IP 66 protection pre-wired with 1.0 Sq.mm. copper conductor cable up to connector including 1.5m long GI tubing light grade 32mm dia., bend to shape for fixing on wall/pole with suitable MS brackets nuts and bolts etc. complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Factory made flush shutter type sheet metal enclosures, double door, for MCCB DB load link, Vertical, single pole and neutral, 12 way IP-43, Suitable for MCCB up to 160A as incommer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SP-06 to 32 Amp, 240 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB TPN-40 to 63 Amps Amp, 240 volts 50Hz AC supply complete all as specified and as directed by the Engineer-in-Charge.

M&L earthing complete with copper plate electrode 60cmx60cmx3mm thick, buried directly in ground (Earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to copper earth strip 38x5mm size by means of bolts, nuts, check nuts and washers of copper all as shown in electrical plate No.3 of SSR Part-I connected to earhing test point & anti static flooring all as specified or indicated including excavation and connected earth work in hard/dense soil, PCC 1:3:6 type C1 as in pit, 20mm dia. GI pipe medium grade for watering pipe, 15mm bore GI light grade earth lead protection pipe, and 50mm thick RCC cover slab with handle, reinforced with 10mm dia. bars in both the directions, funnel, strainer, charcoal and testing on completion all as specified and as directed by the Engineer-in-Charge. Notes:1.Rate quoted deemed to include GI protection pipe, funnel, excavation and earth work, in soft/loose soil with PCC type C1 in bed and pit complete all as specified and as directed.

S&F exhaust fan made out of steel body complete with louvers shutter, 230 Volt, 50 Hz, 1200 RPM copper winding of sweep 450mm, fixed on wall including making opening, fixing and making good the distrubed surfaces etc complete with and inclussive of making necessary electric connection from ceiling rose to fan through 1 Sq.mm. twin core flexible wire complete all as specified and as directed by the Engineer-in-Charge.

S&F Steel pipe glavanized grade of 40 mm core laid in trenches or under ground/floor or road of fixed with pole for protection of cable including clams with bolts nuts and washers complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying cable XLPE FRLS Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 4 core 16 sqmm complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for trench of cable/foundation of pole and stay etc and getting out in hard/dense soil soil complete all as specified and as directed by the Engineer in charge.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and as directed by the Engineer-in-Charge.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all as specified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts1.5 Sqmm ( multi-stranded) copper conductor single core( Green co lour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point/fan point independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

One light point or one fan point controlled by one way, single pole switch

One 3 pin socket outlet, 6 Amp on “independent board”

Description all as per serial item No. 110.00 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing LED 9 Watt complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 1x10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing sheet Metal enclosure singlr shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.

Supply and fixing MCB single pole and neutral 35 to 60 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 1991 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .

S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 10 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.

M/S ULTRA INDUSTRIES (BID ID -3324604)

M/S HONY CAPT RIGZIN SAMPHEL (BID ID -3324844)

M/S GLOBAL ENGINEERS (BID ID -3324424)

M/s Koul & Sons (BID ID -3323761)

M/S MOHD KARIM (BID ID -3324600)

M/S ASGAR ALI TIMBER SHOP (BID ID -3324557)

M/S MA CONSTRUCTION Co (BID ID -3324901)