JOINT FILLING OF RUNWAY AND TAXI TRACK AND OTHER WORKS UNDER GE NASIK ROAD CAMP

Amount

M&L for raking out existing construction joints/dummy joints 10mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

M&L for raking out existing expansion joints 20mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

M&L for filling construction joints/ dummy joints 10mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

M&L for filling expansion joints 20mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

M&L for painting lines, dashes, arrows, letters, and painting dispersal area etc. on roads, concrete pavements and the like exc 10cm wide with two coat of water based paint, white or golden yellow including preparation of new or previously treated surfaces to receive the painting. (Painting shall stand out boldly and solidly without showing signs of brush marks or surface underneath. If necessary, the surface shall be repainted by one or more coats until the desired result is obtained.)

M & L for painting lines, dashes, letters, arrows etc. on road pavement, parade ground and aplying 2mm thick road marking strips (reflective) of specified shade/colour using hot thermoplastic material by fully/semi automatic application mechine fitted with profile shoe heater; driven by experienced operator including preperation and cleaning of surfaces complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Dismantling wrought iron or mild steel work of any description such as purlins ofor roof and window guard bars.

Supply and fixing steel work in tubular or rectangular hollow section in rafters, purlins etc. and connected works complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 2mm thick Fibre glass reinforced translucent reinforced corrugated sheeting with two corrugations side lap fixed with coach screw and washers in roof wall etc complete all as specified and as directed.

M&L for Preperation of new untreated steel or iron surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enemel paint over a coat of red oxide, zinc chrome primer.

Taking down aluminium door shutters of any description.

Taking down aluminium window shutters of any description.

Taking down aluminium door and window frame of any description.

M&L for Aluminium (minimum 50 micron powder coated) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

M&L for Aluminium (minimum 50 micron powder coated) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

M&L for Aluminium (minimum 50 micron powder coated) window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21, 100mm long (2 Nos.), suitable handle (1 No.), rollers, grip etc. complete all as specified

M&L for 5.5mm thick sheet glass plain or tinted, ordinary quality, fixed in aluminium doors and windows.

M&L for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple or fixed in alumionium frames.

M&L for Floor door closer hydraulically regulated, universal type (cast iron body) suitable for aluminium door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

M&L for Preparation of old or previously treated steel or iron surfaces of any description over 10cm width or girth and two coats of aluminium paint over a coat of red oxide primer.

S & F Turbo Ventilator of size 24" dia on roof top of Hangar building inclunding all fixing arrangements complete all as specified, as directed by the Eng-in charge.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level).

M&L for 75 mm thick cement concrete 1:4:8 type D2 (40 mm graded aggregate) in sub floor.

M&L 100mm thk Cement concrete type B-1, 1:2:4 (20mm graded aggregate)

M/L for screed bed or bedding layer20mm thick in cm 1:6 for laying floor finishes complete all as specified and directed by Engr-in-Charge.

M/L for rough shahabad stone 25mm to 30mm thick in flooring /plinth set and jointed in neat cement slurry and pointed in cm 1:4 complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block with grey cement and pigment with rubber moulded glossy finished surface, any shape and size confirming to IS 15658-2006 of 60 mm thickness M-30 grade laid over and including 30 mm thick stone dust cushion.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished in skirting etc. cut out of tiles of area not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick cement mortar rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match.

Non Skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm , in floors etc. including 15mmm thick cement mortar screed bed in cement mortar 1:6,set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick including 15mm thick cement mortar rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work finished fair and even.

M&L preparation of newly plastered surfaces and applying two coat of cement base paint on wall complete all as specified and directed.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling RCC posts or struts any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

S&F rolled section for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire.

Supply only chain link MS galvanisd fencing, any size or type.

S & F 4mm dia plain mild steel wire, galvanised class 3 in fencing including straining and fixing to concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured).

S & F flat iron fillets (for securing wire mesh, chain link fencing etc.) including all necessary drilling, bolting or riveting etc., MS stiffener bars for chain link fencing and similar work.

S & F mild steel screw bolts (machine made) diameter of neck 5 to 10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm.

M&L reparing new untreated steel or iron surfaces any description exc 10cm width or girth and two coats of aluminium paint over and including a coat of red oxide zinc chrome primer.

M&L preparing new untreated steel or iron surfaces any description n.exc 10cm in width or girth and two coats of aluminium paint over and including a coat of red oxide zinc chrome primer.

M/S SAMEER SUBHASH PATANI

Kishor Suresh Patil

M/S K. K. Construction

HINDUSTAN BUILDERS

M/S ANAND G NUNSE