PROVN OF INTERLOCKIN PATHWAY, PROVN OF PARKING SHED, PROVN OF 01 X TOILET CUM BATHROOM, PROVN OF 50X TWO WHEELER PARKING AND PROVN OF PIPE RAILING IN AOR OF AGE BR-II IN DIFFERENT LOCATION UNDER GE(WEST)PATHANKOT

Amount

Sch 'A' Part-I B/R Portion:- Surface excavation not exceeding 30 cm deep and average 15cm deep and getting out in soft / loose soil, complete all as specified.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes 50mm dia and 16 guage, channels, plates etc., fixed in vertical /horizontal position cut to length required size and welding in position alongwith foots and caps of required size including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts alongwith 4mm dia chain of SS fixing in between SS pipe post in 3 layer/line complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by the Engg-in-Charge.

Surface dressing in any type of soils not exc. 15 cm deep and removing surplus materials to a distance exc. 250 mtr as directed by Engr-In-Charge.

Excavation over areas, not exceeding 1.50m deep and getting out in soft/loose soil complete all as specified & directed.

M&L for broken stone or boulders in hardcore of gauge exc 63 mm but n exc 100 mm deposited spread and levelled in layers n. exc 15 cm thick watered and rolled/rammed to a true surface complete all as specified and as directed.

M&L for plain Cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate), 75mm thick as in sub base complete all as specified and as directed.

M&L for 60mm thick glossy finish factory made chamfered edge cement concrete rubber moulded paver block of M-35 grade with approved colour, design & pattern with pigment as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other, Colour of paver blocks & laying pattern approved by GE.

M&L for 80mm thick glossy finish factory made chamfered edge cement concrete rubber moulded paver block of M-40 grade with approved colour, design & pattern with pigment as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other, Colour of paver blocks & laying pattern approved by GE.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as secified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in copings, kneelers, apex stones,bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Excavating in post holes (or similar holes) in any type of soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded aggregate crushed stone aggregate) in foundation and mass concrete complete all as specified

S&F Rolled mild steel roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel, or flat sections) including distance pieces, cleat etc. or other connecting plates confirming to Fe-290 (Gde E165) including appling two coat of synthetic enemal paint over a coat of red oxide primer on exposed surfaces complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft & loose soil complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling or mass concrete as specified and directed

Returning, Filling in, including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc 250 m and depositing where directed at level n exc 1.5m above the starting point complete all as specified and directed.

M&L for Brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using12.50 mm graded crushed stone aggregate as in flooring and surface finished rough all as specified and as directed.

M&L for Brickwork with subclass 'B' old size bricks, straight or curved on plan any radius in half brick, built in CM (1:4) complete all as specified and directed.

M&L for MS TMT bars of Grade Fe 500D, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

All as per srl item No. 21 here-in-before but 5 to 10mm dia in stirrups, spacers & binders etc complete complete all as specified and directed.

Use & Waste Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for RCC, M-20(Nominal Mix) using 20mm graded crushed stone aggregate for roof Slab supported on wall, beam and column etc complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work ,concrete surface of wall finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on other than fair faces of brick work ,concrete surface of wall finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade over and including a coat of primer complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified .

S&F factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

M&L for 100 mm thick Cement concrete type D-2, 1 : 4 : 8 (using 40mm graded crushed stone aggregate) as in sub floors/sub bases etc. complete all as specified and as directed.

M&L for 100mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base even and rough finish complete all as specified and as directed.

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified.

S&F tube medium grade galvanized with all fittings and fixed to walls or laid in floors of 15mm bore including cutting chasing in walls etc if required complete all as specified and directed.

S&F tubes medium grade galvanized with all fittings and fixed to walls or laid in floors of 20mm bore including cutting chasing in walls etc if required complete all as specified and directed.

Cutting chase, pining in making good to facings where required and pointing in cement mortar (1:3) to ends, cutting chases for concealed water tubing ror concealed conduit wiring etc and making good cutting not exc 10cm girth.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete, including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F 15 mm dia PVC connection of 450mm long, PTMT nuts.

S&F Aluminium, anodised, barrel tower bolts of 200 mm long and 10mm dia stove enamelled black with bright bolt fixed complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised fixed complete all as specified and directed.

S&F stainless steel hinges, 100 mm long of medium weight, fixed with screws, complete all as specified & directed.

S&F 5 mm thick sheet glass plain/figured pin head type ordinary quality and glazing with oil putty wire clips in square n.exc 0.5 sqm in each pane upto triple story building complete all as specified and directed.

M&L for cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in benching, cills, lintels up to 1.50 mtr clear span, bed plates for securing hold fasts & back filling of hollow portion of chowkats etc complete all as specified and directed.

M&L for Preparation of new steel surface of any descripion over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed..

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant priming, of any approved colour including necessary scaffolding if required, all painted areas site to be cleaned and hand over as earlier without any extra cost, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles, area of each tile exceeding 0.11 square metre but not exceeding 0.18 square metre of 7 to 8 mm thick set and jointed in neat cement slurry and pointing in coloured cement to match shade as in skirting/dado including 15mm thick rendering in cement mortar 1:6 complete all as specified and as directed.

M&L for Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming with Fe 410-W (Gde E- 250) quality- A complete all as specified and as directed by Engg-in-Charge

S&F pre-painted galvalume aluminum zinc coating AZ-150, GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in sunshades, roof covering, cladding to wall etc fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminum zinc coating AZ-150, GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall and as in ridge etc fixed with self-tapping screws as specified.

S&F false ceiling with fibre cement designer tiles ivory painted (high pressure steam cured) of 4mm thickness (as per IS:14862) of size 595 x 595 mm and any one of the design (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600 mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to exising rafter, purlin, etc with galvanised butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T-sections shall be centra black pre-painted with polyester paint, and havng a load bearing capacity of 12Kg/sqm, and refixed all existing electric wiring and fixture all complete at all heights as per direction of Engineer-in-Charge

M&L for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate, in cover slabs( for manholes etc.) chulla hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:6) complete all as specified and directed. (Reinforcement shall be measured and paid separately).

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed including fixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as spd & directed.

S&F CP stop cock/angle valve cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as specified & directed.

S&F stop valves, 15mm dia, cast copper alloy,chromium plated fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed

S&F pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

S&F Brass CP shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. Make Jaquar Cat part no. Health Faucet SKU ALD-573 or equivalent in any of the make metnioned in list of product.

S&F Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F Wash basins, Vitreous China (flat back type) 550 x 400mm, including cutting for and pinning in ends of brackets or erecting stand, including 32 mm dia 75 cm long PVC flexible waste pipe etc complete all as specified and as directed.

S&F Viterous China urinal, half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S&F 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F PVC (SWR) bends any radius 110mm dia all as specified and directed.

S&F PVC (SWR) accessible door bends any radius 110mm dia all as specified and directed.

S&F PVC (SWR) 110mm bore vent cowl complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) reducers 75/100 dia all as specified and directed.

S & F 125mm dia chromium plated perforated grating with hole/without hole for waste pipe fixed over floor/nahani trap complete all as specified and directed.

S&F 75/110mm PVC floor trap, ISI marked with CP grating with/without waste pipe hole incl jointing to waste pipe fixed with solvent cement complete all as specified and as directed.

S&F PVC (SWR) 110mm bore 'T' equal or unequal complete all as specified and directed.

Powder coated (of approved color) aluminium sections as in frame & shutter of Door, windows, ventilators as in sliding / openable / louvers / fixed type with and including necessary rolling for smooth moving & locking arrangement, etc. fixed to wall including, preparation of disturbed portion both sides (internal & external surfaceof wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-in-charge.

M&L for point wiring for one light/one fan controlled by one switch with 1.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H 1100 volte grade cable, with and including PVC rigid concealed conduit (ISI marked) with all fittings including sheet steel/CI terminal box of adequate size including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly, complete all as specified and directed. Note:- 1. connection of cable with MCBs/switch sockets shall be done through proper size copper /brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible. 3. Proper colour coud will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 76 here-in-before but for 5 pin 5 amps socket outlet on the independent board controlled by one switch SP, one way 5 Amp, 240 Volts. complete all as specified and directed.

M&L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable with in and including PVC concealed conduit heavy duty with all fittings including anodise pressed steel sunken box with bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S&F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S&F mirror light 10 Watt LED 2 feet length complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of suitable size complete all as required at site or directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F CFLs with LED Lamp, B22 type ,12 watt,complete all as specified and directed.

S&F sleek LED Batten light fitting, 1x20 W including LED tube 4 feet long of same make having ballast , bipin holder, connector block etc. complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of suitable size complete all as required at site or directed.

S&F sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F MCB SP 240 volts any rating from 6 to 40 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F MCB SPN 240 volts any rating from 6 to 40 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length not less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

Supply and installation of the electric water storage heater of ABS body type, 25 ltr capacity with rated power 2KW, 5 star rated, vertical type, thermally insulated mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostat, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm bore with GI hexagonal adopters/nuts on both sides for inlet (cold water supply) & outlet (hot water supply) and including provision of wall mounting arrangements and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I and connecting to existing earth test point complete all as specified and directed or including testing on completion.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Supply, laying and testing LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 16 sq. mm 2 core complete all as specified

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of cable ,pole foundation,stay,laying of pipe etc complete all as specified and directed.

Returning filling in, including spreading ,leveling ,watering and well ramming in layers not exc 25 cm complete all as specified.

Removing excavated soil to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified (Note:-Punned thickness shall be measured and paid)

M&L for brick covering equal to length of bricks as mechanical protection to cable with well burnet sub class ‘B’ bricks laid as directed by the Engr-in-Charge.

S&F GI tubing light grade 50 mm bore for cable protection laid in trenches in road crossing or fixed to wall/Pole including fittings /clamp complete all as specified and directed.

M&L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and S&Fing propeller MS ventilating fans, Single phase, 230 volts 300 mm or 12" sweep complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core of suitable size copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S&F tubes medium grade galvanized with all fittings and fixed to walls or laid in floors of 20mm bore including cutting chasing in walls etc if required complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, Bore dia of pipe 20 mm

M&L for cutting/drilling of 50/80mm GI pipe for connection of 15mm GI pipe including all required fitting and accessories complete all as specified and as directed.

JP AND CO. (BID ID -3436565)

HARI OM ENTERPRISES (BID ID -3430707)

M/S SATYA SAI CONSTRUCTION (BID ID -3436837)