Separate Water Supply Scheme for village Dhuge, Loothre , Ditan, Dhilwan, Haleran , Badewal, Bilna Chandpur in tehsil Haroli Distt Una HP

Amount

Excavation in foundation trenches upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing or pumping out water, blasting soft / hard rock or chieselling soft/ hard rock where blasting is prohibited, in all lifts including trimming and dressing of sides, levelling of beds to correct grade including, shoring, strutting, planking, timbering and dewatering, wherever required, stacking the useable and unuseable material/ soil separately and after laying, jointing and testing of pipes returing the useable soil in trenches in 15 cm ( Fifteen centimeter ) layers including consolidating of such deposited layer by ramming and watering and then disposing of all surplus excavated soil /un-useable materials as directed within all leads and lifts including restoration of un-metalled surface to its original condition and including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respect within all leads and lifts complete in all respect to the entire satisfaction as per the directions of Engineer-in-Charge.

Providing and laying cement concrete by using M-10 graded stone aggregate 40 mm nominal size )complete in all respect within all leads and lifts complete in all respect to the entire satisfaction as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12 (1cement: 6 sand) 12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundation and plinths in all leads and lift and to the entire satisfaction of Engineer-in-charge.

1st. class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement : 6 sand) in all lead and lifts and as per the directions of the Engineer-in-Charge.

P/L DPC 38 mm thick cement concrete 1:2:4 (1 Cement:2 sand: 4graded stone agreegate 12.50 mm nominal Size) in all leads and lifts and as per the direction of the Engineer-in-Charge.

Applying a coat of ho bitumen (Mexphalt 80/100 of equivalent) using 1.70 Kg/Sqm on damp proof course complete in all respect all leads and lifts and as per the direction of the Engineer-in-Charge.

Brick work using common burnt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) complete in all respect including all lead and lifts and as per the directions of the Engineer-in-Charge.

Providing and laying cement concrete 1:1.5:3 ( 1cement 1.5 Sand :3 graded stone aggregate 20 mm nominal size and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :-

Foundations,footings bases of columns and the like

Suspended Floor, roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever upto floor two level

Walls (any thickness but not less than 0.10 mtrs. thickness) including attached pilasters, buttersses, plinth and string courses etc. from top of foundation level.

Arches upto floor two level

Half brick work using common burnt clay building bricks in super structure above 1st. floor level in cement mortar 1 : 4 ( 1 cement :4 sand) of 2nd. Class bricks complete in all lead and lifts as per the direction of the Engineer-in-Charge.

Providing form work with steel plates 3.15 mm. thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:

Flat surfaces such as soffits of suspended floors, roofs,landings and the like. Floors etc.upto 200mm. in thickness within all leads and lifts as per direction of Engineer-in-charge.

Beams, cantilever, girders and lintles Sides and soffits of beams, beam haunchings cantilevers bressumers and lintles not exceeding 1 mtr. in depth in all height from floor in all leads and lift to the entire satisfaction of Engineer-in-charge.

Vertical Surface such as wall (any thickenss) partitions and the like including attached plasters, buttresses, plinth and string courses and the like.

Providing Tor steel reinforcement for RCC work including bending binding & placing in position complete upto floor two level complete in all respect including all leads and lifts and to the entire satisfaction of Engineer-in-charge.

15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and /or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

20mm Cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement: 6 sand) within all leads and lifts as per direction of Engineer-in-charge..

6 mm cement plaster to ceiling in cement mortar 1:3 (1cement : 3 sand) within all leads and lifts and as per direction of Engineer-in-charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jumb lock jamb,beed and if reuired angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel butt hinges 2.5 mm thick with guards,lock strike plate and shock absorber as specified and applying a coat of approved steel primer after pretretment of the surface complete in all respect including all leads and lift to the entire satisfaction of Engineer-in-charge. Profile-A

Providing and fixing 1mm thick MS sheet door with frame of 40mm x40 mm x6mm angle iron 3.15 mm MS gusset plate at the junction s and corners including all fittings complete including applying priming coat of read lead paint using flat 30 mm x6mm for dioagonal braces and control cross/pioeces complete in all respect including all leads and lift to the entire satisfaction of Engineer-in-charge.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 graded stone aggregated 20mm nominal size) including carriage of materials and as per directions of the Engineer-in-charge.

Providing and laying cement concrete flooring 1:2:4(1cement:2sand: 4graded stone agg., 20mm nominal size) laid in one layer finished with a floating coat of neat cement within all leads and lifts as per direction of Engineer-in-charge. 40mm thick.

Providing 40x3mm flat iron hold fast 40 cms long in cement concrete block 30x10x15 cms 1:3:6 (1 cement :3 sand : 6 graded stone aggregate 20 mm nominal size )

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing MS handles with necessary screws etc complete in all respect i/c all leads and lifts and as per the directions of the Engineer-in-Charge.. . 100 mm

Providing and fixing MS. tower bolts ((Barrel type) with necessary screws etc complete in all respect i/c all leads and lifts and as per the directions of the Engineer-in-Charge.. 200x10mm.

Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with necessary screws etc complete in all respect i/c all leads and lifts and as per the directions of the Engineer-in-Charge 300x16mm

P/F on wall face Cast Iron rain water pipe 100 mm dia i/c all fittings and joints with spun yard and cement Motor 1;2(1cement; 2sand) including clamps complete in all respect i/c all leads and lifts and as per the directions of the Engineer-in-Charge..

Applying priming coat over new steel and other metal surface after and including repairing the surface by thoroughly cleaning oil grease dirt & other foreign matter & papering & knotting red lead paint brushing complete within all leads and lifts as per direction of Engineer-in-charge..

Painting two coats (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint with brushing complete within all leads and lifts as per direction of Engineer-in-charge..

White washing with lime on undecorated walls surface (Two coats) to give an even shade including throughly brooming the surface dirt, dust motor dust and other foreign materail complete in all respect in all leads and lifts and as per the direction of the Engineer - in- Charge.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt,dust and remains of loose powdered material in all leads and lifts and as per the directions of the Engineer-in-Charge.

P/F MS fan clamps type 1 of 16 mm dia bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of roof as per standard design complete in all respect and as per the direction of the Engineer-in-Charge.

Pointing on brick work with cement mortar 1:3 (1cement: 3 sand) raised and cut point within all leads and lifts and as per direction of Engineer-in-charge.

Steel work welded in built up sections,trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paintcomplete in all respect and as per the direction of the Engineer-in-Charge.

P/F CI man Hole Cover with frame (medium duty) 500 mm internal dia weight of cover not less than 58 Kg including all leads and lift.

Proving and fixing Sand Cast/ Cast iron spun spigot & socket soil waste and vent pipe 100 mm dia including all leads and lift.

Providing form work of ordinary timber plankings so as to give a rough finish including centring, shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 metres and removal of the same for insitu reinforced concrete and plain concrete work in Arches upto 6 metres span complete in all respect and as per the direction of the Engineer-in-Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) complete in all respect and as per the direction of the Engineer-in-Charge.

Fixing GMS tube (Light class) tube fitting for Outlet, Inlet, Scovr pip (earth work in trenches to be measured and paid for separately) complete in all respect and as per the direction of the Engineer-in-Charge.

GMS pipe 100 mm dia

Providing and fixing C.I. Sluice valve (With hand wheel) as per IS -780-1984 class-I upto 300 mm dia (including brass spindle and as per IS; 2906-1984 class -II dia >300 mm) complete with nuts, rubber insertion etc. complete ( The tail piece if required shall be measured and paid fior seperately )

100 mm dia for overflow pipe & Scover pipe

Prv. & fixing SFRC Man hole cover with frame having frame size of 560 mm internal dia should not less than 116 Kg. complete in all respect and as per the direction of the Engineer-in-Charge.

Providing and fixing white vitreous china wash down water closet (Orrisa type W.C.pan) withintegral 'P'or 'S' trap including jointing the tap with soil pipe in CM 1:1 of Parryware / Hindware/ CERA as per the direction of engineer in charge.

Providing and Fixing 500 Liters cap Sintex water Storage tank double Layer with top lid and making connections complete in all respect as per the direction of Engineer- in -Charge.

Providing and fixing 10 liters PVC low level flushing cistern with necessary screw complete with fitting such as lead valve with polythene float C.P brass handle, unions and couplings for connecting with inlet, outlet and overflow pipes 15mm dia. C.P flush bend complete in all respect as per the direction of Engineer- in -Charge.

Wiring for light point/fan point/exhaust fan/ call bell point with 1.55q. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core e (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable complete in all respect. "Group-C

Wiring for 3pin 5/6 amp socket outlet point on swich board in (surface/recessed PVC wiring system) and 5/6 amp tumbler piono type switch earthing the 3 pin painting etc as required with in all leads & lifts complete.

Wiring for power plug with (2x4 Sq.mm) PVC insulated, heat resistant flame retardant (HRFR) and low smoke single core(flexible)copper conductor cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm. HRFRLS/PVC insulated sigle core copper conductor cable for earthing as required including carriage of material with in all leads & lifts complete.

Wiring for light plug with (2x1.5 Sq.mm) PVC insulated, heat resistant flame retardant(HRFR) and low smoke single core(flexible)copper conductor cable in surface/recessed PVC conduit along with 1 No. 1.55q.mm.HRFRLS/PVC insulated sigle core copper conductor cable for earthing as required including carriage of material with in all leads & lifts complete.

Wiring for circuit/sub-main with 2x10 Sq. mm size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required including carriage of material with in all leads & lifts complete.

Supply and fixing of metal box of 180x100x60 mm deep( nominal size ) on surface /recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 3 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, ainting etc. as required.

Supplying and erection of floor mounted fixed type metal frame work/boards of esting and commissioning etc comple complete Cat A es required with in all leads Hitswelded construction for switch gear mounting fabricated with M.S. angle iron (50 mm x 50 mm x 6 mm thick) of suitable dimensions with supporting members grouted 23 cm underground and frame work covered with 3um thick M.S. sheet from top to a given height, with M.S. angle iron/50mmx50mmx 6mm thick welded on the back and grouted into the back wall complete with painting and bonding to the existing earth as required with in all leads & lifts complete.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required with in all leads & lifts complete. Double

Supplying and fixing 40Amps to 63 Amps rating 240 Volts "L" series miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material within all leads and lifts. Category- A, 63 Amps.

Supplying and foxing 63 amp rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 30 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc as required with in all leads & lifts complete Cat. A

Supplying and fixing 5 to 32 amp rating 240 volts "L" series MCB of single pole in the existing MCB DB complete with connection, testing and commissioning etc as required with in all leads & lifts complete.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required with in all leads de lifts complete. Ceiling Fan 1200 mm sweep, Category-A

Providing, Installation, testing and commissioning of prewired flourscent tube fitting 1x40 watt box type Cat A Bajaj make complete with balast starter and capacitor but excluding flourscent tube rod suitable to operate on 240volt single phase AC supply directly on surface with copper wiring as required complete as per direction of the Engineer in Charge.

Earthing with G.1 earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt)complete as required.

Extra for using salt and charcoal for pipe earth electrode complete as required.

Supplying and laying 6 SWG G1 wire on surface / recess for loop earthing as required complete as per direction of the Engineer-in-charge.

P/F street light fixture 40watts 4 feet long complete with choke starter i/c connection complete as required complete as per direction of the Engineer-in-charge

OHSRS

Excavation in foundation trenches etc. in earth work in all kinds of soil such as spade work, pick work, jumper work, blasting work in soft and hard rock chieselling / wedging out rock where blasting is prohibited and in saturated soil etc. in all leads and lifts, stacking the excavated soil not more than 3 mtrs clear from the edge of excavation and then returning the stacked soil in fifteen centimeters layers, when required into plinths sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lifts as per the directions of Engineer-in-Charge.

Providing and laying cement concrete by using M-10 graded stone aggregate 40 mm nominal size )complete in all respect within all leads and lifts complete in all respect to the entire satisfaction as per the directions of Engineer-in-Charge.

Providing and laying cement concrete using M-25 concerete mix with graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :-

Foundations, footings, bases of columns etc. and the like mass concrete.

Columns, pillars posts and struts above GL to floor two level

floor two level to floor three level

floor three level to floor four level

Lintels, beams, girders, bressumers and cantilevers upto all heights.

floor two level to floor three level

floor three level to floor four level

Arches

floor two level to floor three level

floor three level to floor four level

Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever upto floor two level complete in all respect and as per the direction of the Engineer-in-Charge.

Walls (any thickness but not less than 0.10 mtrs. thickness) including attached pilasters, buttersses, plinth and string courses etc. from top of foundation level.

from three level to floor four level

from floor fourl level to floor five level

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30 x 30 x 5mm, so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu-reinforced concrete and plain concrete work in all leads and lifts and as per the directions of Engineer-in-Charge.

Foundation, footings, basis of columns etc. and mass concrete.

Columns, pillars, posts and struts Circular or curved in plan upto all heights.

beyond 4 mtr

Sides and soffits of beams, beam haunchings,cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floors.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like.

upto 4mtr

for vertical surface of tank

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc. upto 200 mm in thickness upto all heights..

Providing form work of ordinary timber plankings so as to give a rough finish including centring, shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 metres and removal of the same for insitu reinforced concrete and plain concrete work in Arches upto 6 metres span complete in all respect and as per the direction of the Engineer-in-Charge.

not exceeding 4 mtr

beyond 4 mtr

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete in all respect including carriage of materials within all leads and lifts and as per directions of the Engineer-in-charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) complete in all respect and as per the direction of the Engineer-in-Charge.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt,dust and remains of loose powdered material in all leads and lifts and as per the directions of the Engineer-in-Charge.

Providing and fixing 500 mm dia SFRC manhole cover with frame and (Medium grade duty) weight of cover and frame to be not less than 100 Kg.

Fixing inlet, outlet, over flow and scour pipe of GMS pipe of following internal dia (medium grade) including extra carriage within all leads and lifts and as per directions of the Engineer-in-charge.

Inlet Rising Main

100 mm dia

65 mm dia.(MG)

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting ,fixing in position and applying a priming coat of red lead paint In gratings, framed guard bars, ladders, railling, brackets and similar works within all leads and lifts and as per the direction of the Engineer-in-Charge. .

Fixing GMS pipe confirming to IS 1239-1979 ( part-1) screwed &socketed joints (Light grade) excluding the cost of excavation in trenches 50 mm dia

Providing and fixing CI sluice valve (With hand wheel) as per IS -780 class for following dia (including brass spindle and as per IS; 2906 class -II including M.S. Flanges, bolts, nuts, rubber insertion etc. complete in all respects including carriage of material within all leads and lifts.

100 mm dia

65 mm dia

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 graded stone aggregated 20mm nominal size) including carriage of materials and as per directions of the Engineer-in-charge.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

P/F of below items required for OHSR complete :-

Providing and fixing of water measuring gauge of standards design complete in all respect.

MS sheet locking arrangement for man hole cover complete in all respect including carriage and as per the directions of Engineer-in-Charge.

Providing and fixing of sky lightening arrestor complete in all respect including carriage and as per the directions of Engineer-in-Charge.

Water measurement gauge complete in all respect including carriage and as per the directions of Engineer-in-Charge.

Providing and fixing of vent opening including cowl with mesh in the top of the tank complete in all respect including carriage and as per the directions of Engineer-in-Charge.

Ankush Dhiman

Om Parkash Govt Contrator

aditya govt. contractor

Ravinder Kumar Sahore

Pershant Rai

SG Engineers and Consultants