Special Repair and Renovation of official Premisses for Holding Sarkar Tuhade Dwar by Honble Chief Minister Punjab At Jalandhar Under Head 4215

Amount

Sub Head 1 - Sanitary Installation

Providing and fixing in position Chinaware extended wall mounted E. W.C. type suite (size 66 x 46 x 77.5 cm ) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge

Chinaware wall mounted E.W.C without cistern including seat cover complete in all respect.

Providing and fixing in position concealed cistern including flushing plate of approved make (to the approval of the Engineer-in- charge) complete in all respect.

Providing and fixing in position Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Chinaware Floor Mounted One Piece EWC rim less type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) size 69x36x74 cm with P trap or S trap and seat cover complete in all respect.

Providing and fixing Stainless steel health faucet complete in all respect.

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair 115mm long without CP fittings complete in all respect.

Table Top (size 49 x 40 x 15 cm)

Size 630 mm x 450 mm x 830 mm

Providing and fixing vitreous chinaware pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

Vitreous chinaware standard white pedestal for wash hand basin.

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect.

Note:-To be provided only for VIP Installations and with prior approval of the Engineer-in-charge.

C.P. Brass Accessories:

C.P. brass towel rail 600 mm long

C.P brass towel ring square

C.P. brass toilet roll holder with flap

C.P. brass towel rack 600mm long with lower hangers

C.P. brass soap dish holder with glass dish

C.P. Glass Shelf 600mm long

C.P. Brass fittings:

C.P. brass 3-Hole Basin Mixer Without Popup Waste System

C.P. brass Bib cock with Wall flange

C.P.brass 15mm Angular stop cock with Wall flange

C.P. brass 15mm Concealed stop cock with adjustable wall flange with seal.(Outer +Inner Body)

C.P. brass overhead shower Φ180mm round shape single flow with shower arm with 20mm i/d Inlet and 300mm long round shape with 900 bend with flange

Providing and fixing in position CP Brass Grab Bar of approved make (to the approval of the Engineer-in-charge) fixed in to wall with brass screws complete in all respect.

Providing & Fixing in postion liquid soap container of approved make (to the approval of Engineer-in-charge ) complete in all respect. (A)C.P. brass liquid soap Dispanser

Providing & Fixing in position mirror of superior glass Size 1500mm x600mm or any other required size (of approved quality) and of required shape and size with high quality polystyrene moulding frame of 40 to 50mm size (of approved quality and shade) with 4mm thick hardboard backing fixed in with rawl plugs 50mm, C.P. brass screws and washers complete in all respect

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect

PVC tube connection of size 15 mm x 450 mm with C.P. Brass nut

Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect.

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete. ii)25mm i/d Brass Ball valves

Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-in-charge )with various fixtures complete in all respect.

i) C.P. Brass extension piece, 25mm long to 50mm long

Providing and fixing divertors of approved make (to the approval of Engineer-in-charge) for bath and shower system complete in all respect.

Single lever concealed divertor for bath and shower system (3 inlet flow) with body and upper part

Providing & Fixing in postion CP Brass bath tub spout with wall flange of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer - in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank.

Triple Layer Tanks

Providing and installing in position premium range water pressure boosting pump (To the approval of Engineer-in-charge) including all pump accessaries but excluding cost of G.I pipe & specials complete in all respects.

Pressure pump of 0.7 HP with 3100 LPH, 25.6 meter head with SS pump & 24 litre capacity Tank Model : CM 3-4

Construction of Platform for HDPE tanks complete in all respect.

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.

G.I. tank nipple 25mm i/d

Providing and fixing in position automatic brass Ball Cock in tanks.

Brass Ball Cock with rod and Plastic Ball

Providing and Fixing in position Glass shower enclosure L shaped 8mm thick with chrome finish with sliding door and entry from the front of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in postion storage type automatic electric water heater pressure / non pressure type thermostatically controlled, single phase, vertical wall mounted of approved make (to the approval of Engineer-in charge) with thermostats, inner container of stainless steel complete with 1 Mtr. three core flexible cord with plug, non return valve and pressure release valve complete including fixing and testing complete in all respect.

25 litre capacity water heater

Sub Head 2 -Internal Water Supply

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in- Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.

b) c CPVC SDR 11 Pipe & fitting 20mmo/d

c) c CPVC SDR 11 Pipe & fitting 25mmo/d

d) c CPVC SDR 11 Pipe & fitting 32mmo/d

e) cCPVC SDR 11 Pipe & Fitting 40 mm o/d

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition.

Size 150 mm x 150 mm

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required.

Through wall 11.43 cm thick

Through wall 22.86 cm thick

Dismantling concrete

Cement concrete plain1:2:4 mix

Sub Head 3 -Internal & Estate Sewerage System

Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.

160 mm o/d pipes

200 mm o/d pipes

Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, trimming sides and side slopes for sewers and manholes to full depths as shown in drawings,including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ramming and restoration of surface to original level and removal of surplus spoil from the site of works, upto one chain (15m) complete in all respects.

For depth exceeding 3.0 m but not exceeding 4.5 m B.G.L. For all classes of soil except rocky

(50 x 0.75 x 1.30 = 48.75 say 49 cum

Providing and filling sand grading as per specifications or fine grade around the various sizes of G.I. pipes in external work.

For covering Sewer Line Type II

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonagepipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.

Single Socket Type B

b) 110mm o/d SWR UPVC pipe lines laid complete

c) 90mm o/d SWR UPVC pipe lines laid complete

Providing and fixing in position SS Gratingwith frame of approved make (to the approval of engineer in charge) complete in allrespects

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.

For 110mm o/d pipes

ii) Single Tee With Door

iii) Single Tee

iv) Door Elbow 90 Degree

vi) Vent Cowls

vii) Reducer 110mm x 75mm

ix) P Trap/Floor Trap 110mm x 110mm

xi) Single Y-Junction

(v) Elbow 90 Degree (All side socketed)

For 90 mm o/d pipes

ii) Single Tee With Door

iii) Single Tee

iv) Door Elbow 90 Degree

v) Elbow 90 Degree

vi) Vent Cowls

xi) Single Y-Junction

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement,R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

600mm x 900mm inside with 455mm x 455mm cover and frame light duty double seal

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.

100mm internal Diametre H.C.I. gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Constructing brick masonry manhole in cement mortar 1:5 ( 1 cement : 5 coarse sand ) R.C.C. top slab 20cm thick using M-20 mix by using mixer and vibrator, TMT Fe500 @ 80.00 kg/per cum, foundation concrete 1:4:8 mix (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making 40mm thick benching in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, Orange coloured PVC steps including RCC cover with frame complete as per standard design complete in all respects.

Inside size 75x120 cm and 120 cm deep

Sub Head 4 - Flooring Wall Tiles & Dismantling

Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

12.5 mm thick cement plaster 1:2

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/ Highlighter/ emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x600 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling using mechanical mixer for mixing of material

Providing and laying Anti skid Matt Finish floor tiles of size 600x600 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading.

By Manual Means (A) Stone (building or pitching) Sand, Earth, Fly Ash, Bajri, Shingle, Spalls, Brick bats, Brick ballast and Stone metal.

(i) Earth,Surkhi, Sand, Earth, Fly Ash, Bajri, Ballast, Stone boulders, Kankar and building rubbish, Earth.

Scraping

(a) White wash and colour wash

Preparation of plastered surfaces for distempering including surface, applying filling with approved quality filler consisting of plaster of paris and chalk mitti including finishing the surface to the required finish complete

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Dismantling concrete

Cement concrete plain1:2:4 mix

Cement concrete 1:2:4

a With stone ballast or shingle I mixing by manual means

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled.

Doors of area 3 sqm and below.

Dismantling H.C.I Soil pipes including disposal as desired by the Engineer-in-Charge.

100mm i/d H.C.I. pipe

Dismantling H.C.I specials including dismantalling of lead joints including cartage / disposal within 5 Km.

100mm i/d H.C.I. specials

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes,M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Dismantling Sanitary fixtures such as Eurpoean/Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr. complete in all respect as required by Engineer-in-Charge.

Eurpoean/Indian/Orissa W.C.,

PVC / China Ware Cistern

Wash Hand Basin / Urinal Pot

CP Bib Cock/Angle Cock/Stop Cock/Shower/Bottle Trap

Wall mixer / Sink Mixer / Basin Mixer / Concealed Stop Cock

Bathroom Assessories such as Soap Dish, Towel Rail, Towel Ring, Towel Bracket, Mirror, Toilet Paper Holder, Seat Cover, Jet Pressure and all other accessories.

Coloured Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps.

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. (80 sft)

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

115mm thick brick wall in cement sand mortar 1:4 without reinforcement in foundations and plinth

12.5 mm thick cement plaster 1:4

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

The Dashmesh Cooperative Labour and Construction Society Limited