REPAIR/MAINT OF SUBMERSIBLE PUMP SET, MONO BLOCK PUMP SET, HORIZONTAL SUBMERSIBLE PUMP SET, WATER FOUNTAIN, DOL/STAR-DELTA STARTER AND OTHER MACHINERIES OF WATER SUPPLY SYSTEM ALONG WITH CERTAIN CONNECTED WORKS UNDER GE E/M LUCKNOW

Amount

Transporting Oil immersed starter of capacity 7.5 HP to 50 HP of any Make /size from Pump House to Contractor work shop , dismantling for carryout necessary repairs to starter and overhauling, including re-assembling complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/ parts shall be measured & paid separately for unserviceble parts under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Attending the complaint of Oil immersed star delta starter with auto transformer upto 50 HP capacity And AMF Panel round the clock including Sunday & Holiday at any location in Lucknow Cantt area with in specified time not more than two hours complete all as specified and directed by Engineer-in-Charge. Parts renewed shall be measured & paid separately

Supply only set of fixed and moving Contact complete all as specified and directed by Engineer-in-Charge

Supply only of base Plate assembly complete all as specified and directed by Engineer-in-Charge

Supply only set of auxiliary switch I No (Normal open contact) + 1 NC (Normal closed contact) complete all as specified and directed by Engineer-in-Charge

Supply only magnet coil with auxiliary winding rated 415V, AC, 50 Hz complete all as specified and directed by Engineer-in-Charge

Supply only Set of current bar assemblies(Front) complete all as specified and directed by Engineer-in-Charge

Supply only set of current bar assemblies (L1,L2;L3) complete all as specified and directed by Engineer-in-Charge

Supply only set of current bar assemblies (RYB) complete all as specified and directed by Engineer-in-Charge

Supply only thermal overload relay type RB-1 63 range 25 to 40 Amp or 36 to 60 Amp complete all as specified and directed by Engineer-in-Charge

Supply only start & Stop Switch complete all as specified and directed by Engineer-in-Charge

Supply only thermal time delay, relay without transformer type RZ-12 having actuating time range 3 to 12 second complete all as specified and directed by Engineer-in-Charge

Supply only kit kat fuse suitable for 25 HP starter complete all as specified and directed by Engineer-in-Charge

Supply only terminal links RYB & Delta complete all as specified and directed by Engineer-in-Charge

Rewinding of unserviceable / burnt auto transformer with existing size of winding wire complete all as specified and directed by Engineer-in-Charge

Supply only reset push button assembly complete all as specified and directed by Engineer-in-Charge

Supply only wire shapes from contactor to auto transformer complete all as specified and directed by Engineer-in-Charge

Supply only wire shapes with lugs from contactor to contactor complete all as specified and directed by Engineer-in-Charge

Transportation of submersible pump or motor 20 HP to 35 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump and reassembling complete motors/pump sets & depositing the same after necessary repair to site complete all as specified and directed by Engineer-in-Charge Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

M&L for cutting out the burnt existing winding of startor of submersible motor of any make and rewinding with the same size of , copper winding wire, etc as per existing complete all as specified and directed by Engineer-in-Charge

Straightening only of the slots of stator of submersible motor complete all as specified and directed by Engineer-in-Charge

Supply only thrust of ball bearing block complete for submersible motor complete all as specified and directed by Engineer-in-Charge

Renewal only of worn out gun metal bushes for submersible motor as per manufacturer's design complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 16 sqmm size, 8 mtr long complete with suitable clips complete all as specified and directed by Engineer-in-Charge

Supply only sand guard of submersible motor complete all as specified and directed by Engineer-in-Charge

Supply only sleeves of end plates of submersible motor complete all as specified and directed by Engineer-in-Charge

Supply only cable grommet (guard) complete all as specified and directed by Engineer-in-Charge

Supply only water seal complete all as specified and directed by Engineer-in-Charge

Re-metaling of PUMP shaft, turning to bring it to original size and shape and polishing of shaft of submersible pump complete all as specified and directed by Engineer-in-Charge

Supply & fixing coupling of submersible motor and pump with key complete all as specified and directed by Engineer-in-Charge

S & F in repair of broken PUMP shaft with new piece, making key slot, grinding to make coupling size, and balancing the rotor complete all as specified and directed by Engineer-in-Charge

Complete overhauling of submersible pump by carrying out, balancing of pump shaft and cutting of key slots, repairs to bowl assembly, rethreading of wornout studs holes and provding over size studs with nuts complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after.

Supply only bowl bushes complete all as specified and directed by Engineer-in-Charge.

Supply only neck ring complete all as specified and directed by Engineer-in-Charge.

Supply only steel distance pieces & key complete all as specified and directed by Engineer-in-Charge.

Supply only impellor gun metal as per existing complete all as specified and directed by Engineer-in-Charge.

Supply only cast iron, bowl complete all as specified and directed by Engineer-in-Charge.

Supply only CI, non return valve of required dia complete all as specified and directed by Engineer-in-Charge.

Supply only Head Extention (cast iron), complete all as specified and directed by Engineer-in-Charge.

Supply only of Wedges of slots, complete all as specified and directed by Engineer-in-Charge.

Jointing of 3 core cable of any size by using puncture/ rubber compound roll & tape / Sealing compound complete all as specified and directed by Engineer-in-Charge.

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed by Engineer-in-Charge. Note:- Painting shall be done by spray machine.

Transportation of submersible pump or motor 15 HP/7.5/5.0 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump & depositing the same after necessary repair, reassembling complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

M&L for cutting out the burnt existing winding of startor of submersible motor of any make and rewinding with the same size copper winding wire, etc as per existing complete all as specified and directed by Engineer-in-Charge.

Straightening of the slots of stator in repair of submersible motor make as complete all as specified and directed by Engineer-in-Charge.

Supply only thrust ball bearing block as per existing size complete for submersible motor make complete all as specified and directed by Engineer-in-Charge.

Renewal worn out gun metal bushes for submersible motor as per manufacturer's design and specification complete all as specified and directed by Engineer-in-Charge.

Supplty & fixed PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 10 sqmm size, 8 mtr long complete with suitable clips complete all as specified and directed by Engineer-in-Charge.

Supply only sand guard of submersible motor complete all as specified and directed by Engineer-in-Charge.

Supply only sleeves of end plates of submersible motor complete all as specified and directed by Engineer-in-Charge

Supply only cable grommet (guard) complete all as specified and directed by Engineer-in-Charge.

Supply only water seal complete all as specified and directed by Engineer-in-Charge.

Supply only studs with nuts of required length & dia complete all as specified and directed by Engineer-in-Charge.

Re-metaling of pump shaft, turning to bring it to original size and shape and polishing of shaft of submersible motor complete all as specified and directed by Engineer-in-Charge.

Supply only coupling of submersible & pump with key motor complete all as specified and directed by Engineer-in-Charge.

Complete over hauling of submersible pump by carrying out, balancing of pump shaft and cutting of key slots, repairs to bowl assembly, rethreading of wornout studs holes and provding over size studs with nuts complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after.

Supply only bowl bushes complete all as specified and directed by Engineer-in-Charge.

Supply only neck ring complete all as specified and directed by Engineer-in-Charge.

Supply only steel distance pieces & key complete all as specified and directed by Engineer-in-Charge.

Supply only impellor gun metal as per existing complete all as specified and directed by Engineer-in-Charge.

Supply only cast iron bowl assembly complete all as specified and directed by Engineer-in-Charge.

Supply only CI non return valve of required dia complete all as specified and directed by Engineer-in-Charge.

Supply only Head Extention (cast iron) complete all as specified and directed by Engineer-in-Charge.

Jointing of 3 core cable of any size by using puncture/ rubber compound roll & tape / Sealing compound complete all as specified and directed by Engineer-in-Charge.

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed by Engineer-in-Charge. Note;- Painting shall be done by spray machine.

Transportation of Centrifugal monoblock pump set/Horizontal submersible Pump- 10HP to 15HP, AC, 3 phase, 415/420 V from pump house at any location/Yard transporting to contractor's work shop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Cutting out the existing winding of the motor, opening of winding, re winding of motor with same size of winding wire as existing including varnishing, drying and making connection complete all as specified and directed by Engineer-in-Charge.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer complete all as specified and directed by Engineer-in-Charge.

Supply only driven end bearing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only gun metal / stainless steel bush of pump shaft complete all as specified and directed by Engineer-in-Charge.

Balancing and repairing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only non driven end bearing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only of gland and packing complete all as specified and directed by Engineer-in-Charge.

Supply only cooling fan complete all as specified and directed by Engineer-in-Charge.

Supply only cooling fan cover complete all as specified and directed by Engineer-in-Charge.

Supply only CI impeller of similar make complete all as specified and directed by Engineer-in-Charge.

Supply only connection pipe complete all as specified and directed by Engineer-in-Charge.

Supply only coupling with studs between motor & pump complete all as specified and directed by Engineer-in-Charge.

Supply only sleeve of motors as per existing size complete all as specified and directed by Engineer-in-Charge.

Re-metaling of pump shaft, turning for bring it to Internal dia size of bearing in rear end cover complete all as specified and directed by Engineer-in-Charge.

Supply only Neck ring complete all as specified and directed by Engineer-in-Charge.

Removing of Centrifugal pump Set/Horizontal submersible pump set from its existing position and re-fixing of repaired pump set including renewal of worn out nuts & bolts and electric connection complete all as specified and directed by Engineer-in-Charge.

Supply only driven end bearing of motor shaft complete all as specified and directed by Engineer-in-Charge.

Supply only non driven end bearing of motor shaft complete all as specified and directed by Engineer-in-Charge.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed by Engineer-in-Charge. Note;- Painting shall be done by spray machine.

Transportation of monoblock pump sets/ Horizontal submersible pump set 1 HP to 7.5 HP, AC, Single phase, 220/240 V from pump house at any location/Yard in Cantt area contractor's workshop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete all as specified and directed by Engineer-in-Charge. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Cutting, opening of winding, re- winding of monoblock pump set/ Horizontal submersible pump set of any make and rewinding with same size of copper winding wire, varnishing, backing complete all as specified and directed by Engineer-in-Charge.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer. Balancing and repairing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only water seal and packing complete all as specified and directed by Engineer-in-Charge.

Supply only driven end bearing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only non driven end bearing of pump shaft complete all as specified and directed by Engineer-in-Charge.

Supply only cooling fan complete all as specified and directed by Engineer-in-Charge.

Supply only cooling fan cover complete all as specified and directed by Engineer-in-Charge.

Supply only CI impeller of as make complete all as specified and directed by Engineer-in-Charge.

Supply only connection plate complete all as specified and directed by Engineer-in-Charge.

Supply only capacitor of required capacity complete all as specified and directed by Engineer-in-Charge.

Removing of Monoblock pump Set from its existing position and re-fixing of repaired pump set including replacement of worn out nuts & bolts and supply and fixed nuts, bolts and electric connection complete all as specified and directed by Engineer-in-Charge.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed by Engineer-in-Charge. Note:- Painting shall be done by spray machine.

Supply and fixed in repairs Single Phase Preventor Relay complete all as specified and directed by Engineer-in-Charge. Make: L&T/Minilac/C&S)

Dismantling and taking out faulty analog type Ammeter from LT panel and supply and fixing three phase Ammeter digital type upto 0 to 100 Amps with suitable CT's ratio of size 96 mm x 96 mm of any range as required at site including necessary control wire connection and testing complete all as specified and directed by Engineer-in-Charge. Make: L&T/C&S/AE/Secure

Dismantling and taking out faulty analog type voltmeter from LT panel /feeder pillar box and S&F three phase power voltmeter digital type suitable for ( 0-500 volts) range, size 96mmx96mm size including necessary control wire connection and testing complete all as specified and directed by Engineer-in-Charge. Make: L&T/C&S/AE/Secure

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 7.5 to 15 HP, 3 Phase, 415 V electric motar including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all as specified and directed by Engineer-in-Charge. Make: L&T/C&S/Bharat Cutler Hammer/Maxwell/Jyoti.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 20 to 25 HP, 3 Phase, 415 V electric motar including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all as specified and directed by Engineer-in-Charge. Make: L&T/C&S/Bharat Cutler Hammer/Maxwell/Jyoti.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 30 to 50 HP, 3 Phase, 415 V electric motar including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all as specified and directed by Engineer-in-Charge. Make: L&T/C&S/Bharat Cutler Hammer/Maxwell/Jyoti.

Supply and fixed in repairs MCCB 160 Amps, 415 volts AC 50Hz, 3 pole, bracking capacity 36 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repairs MCCB 200 Amps, 415 volts AC 50Hz, 4 pole, bracking capacity 36 kA ajustable thermal setting, Ics=100%Icu@ with suitable size of sheet metal enclosure complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repairs Contactor ML-2, 3 pole, 415 Volts, 32 Amps rating including necessary electrical connection complete all as specified and directed by Engineer-in-Charge. Make; L&T/C&S/ABB

Supply and fixed in repairs Contactor ML-3, 3 pole, 415 Volts ,40 Amps rating including necessary electrical connection complete all as specified and directed by Engineer-in-Charge. Make; L&T/C&S/ABB

M&L Mild screw nut, bolts with washer 12 mm dia and 100 mm long ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs electronic control timer type ET-100 of suitable capacity as required at site, complete all as specified and directed by Engineer-in-Charge. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix in reapirs engine starter relay of suitable capacity as required at site, complete all as specified and directed by Engineer-in-Charge. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix in repairs under voltage relay, complete all as specified and directed by Engineer-in-Charge. (Make:- PIC / EC / Wader.)

Supply & fix in reapirs 8 / 11 pin relay, complete all as specified and directed by Engineer-in-Charge. (Make:- PLA.)

Supplying, laying or fixing, in repairs, jointing and testing LT under ground electric power cable Crossed linked polyethylene ( XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 70 sqmm cross sectional area, 3 1/2 core, complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc.( Excavation, earth work, sand cushioning, protection bricks/ tiles/ block,Clamps, nuts , bolts, washers and pipe shall be measured and paid separately under appropriate items.

All as per item No. 114 above but size of 50 sqmm 3.5 core.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 16 sqmm 3 core complete all as specified and directed by Engineer-in-Charge.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 10 sqmm 3 core complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repair, connecting, testing and commissioning rupturing capacity MCCB 100 Amps , TP , 415 Volts, 16 KA, 50 Hz including spreader terminals complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repair, connecting, testing and commissioning rupturing capacity MCCB 125 Amps , TP , 415 Volts, 16 KA, 50 Hz including spreader terminals complete all as specified and directed by Engineer-in-Charge.

Supply, installation, testing, commissioning & electrically connected feeder pillar outdoor type, single door compartmentized with looking arrangement canopy at top weather proof, verman/dust proof of suitable size cubical type factory made of CRCA MS sheet 3.15 mm thick machine pressed of size 60x60x40 cm & angle iron frame 40x40x6 mm for legs and including grouted in PCC 1:2:4 type B1 (20 mm graded stone aggregate) suitable 440 volts AC 3 phase 4 wire bus bar 4 pole made out of suitable size copper strip capacity 200 Amps Fully mounted on procelain insulator enclosed chamber with open able shutter both sides comprising with following complete all as specified and directed by Engineer-in-Charge.

S&F tail pipece in replacement Made out MS ERW pipe heavy Grade 100 mm dia upto 1.5m in length suitable for submersible pump upto 30 HP including making arrangements for fixing of tie rod, cutting thread & welding flange all as sper site requirement complete all as specified and directed by Engineer-in-Charge.

Disconnection of submersible pump set of any size from existing system water supply & electrical and Taking out /Uplifting the U/S pump set from deep borewell with disconnected from lowering pipe line of any size with manual or suitable electric driven chain pully upto 240 ft depth reassembling after neccesary repair and re-lowering the pump set in same borewell re-connection of complete all as specified and directed by Engineer-in-Charge. Note:- i) Repair of U/s pump set will be paid separately. (ii) All type of T/P required to complete the job will be arranged by contractor. (iii) Job will be done round -o-clock continued as per site requirement as directed by AGE. (iv) Delay in job will be charged on the basis of Rs. 500/- per hour. (v) Items required for motor connection such as PVC insulation tape, valcanised rubber / puncture tube etc will be provided by the contarctor to complete the work and rate as deemed to be quoted in unit rate no extra payment will be made to the contractor.

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 100 bore flange lowering pipe cut type complete all as specified and directed by Engineer-in-Charge.

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 150 bore flange lowering pipe cut type complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations of poles, laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete all as specified and directed by Engineer-in-Charge.

M&L laying well burnt old size Fly ash bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing galvanised mild steel pipe/tubing, 80 mm bore dia, light grade complete with all fittings, laid in trenches / under roads, drain, paths, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers complete all as specified and directed by Engineer-in-Charge. Note:- Excavation & Earth work, mild steel clamps, bolts , nuts and washers shall be measured and paid separately.

S & F in repair , assy to spare parts of Submersible pump cap.15 HP suitable for and upto 12 stages not less than 07 stages incluiding bearing,bush ,shaft,bowels,thrust bearing ,bronze impellers and cashing of pump etc comprising /suitable for directly coupled with motor cast iron body for 250 mm dia borewell multi-stages ,discharge of 1000 LPM at 91 Metre head and complete with suitable end connecting tail piece ,NRV complete all as specified and directed by Engineer-in-Charge.

S & F In repair, assy to spare parts of Submersible motor cap.15 HP with Stator incluiding insulated copper winding ,rotor ,ball bearing ,bush ,terminal plate and cashing of motor comprising with arrangement of directly coupled with pump cast iron body electric driven 415V, TP along with connecting tail piece ,NRV and submersible cable minimum 7.5 RM complete all as specified and directed by Engineer-in-Charge.

S & F in repair , assy to spare parts of Submersible pump cap.25 HP suitable for 12 stages incluiding bearing,bush ,shaft,bowels,thrust bearing ,bronze impellers and cashing of pump etc comprising /suitable for directly coupled with motor cast iron body for 250 mm dia borewell multi-stages ,discharge of 1000 LPM at 91 Metre head and complete with suitable end connecting tail piece ,NRV complete all as specified and directed by Engineer-in-Charge.

S & F In assy to spare parts of Submersible motor cap.25 HP with Stator incluiding insulated copper winding ,rotor ,ball bearing ,bush ,terminal plate and cashing of motor comprising with arrangement of directly coupled with pump cast iron body electric driven 415V, TP along with connecting tail piece ,NRV and submersible cable minimum 7.5 RM complete all as specified and directed by Engineer-in-Charge.

commercial construction

Magneoflux