Open Tender Notice for Open Tender Notice for Conservation and Developmental work of Jagadiswarswami Temple at Buguda, Dist - Ganjam for 2024-25

Amount

Conservation and Developmental work of Jagadiswarswami Temple at Buguda, Dist - Ganjam

Item No.1: Raking out joints of stone masonry surface to the required width and depth, with due care and precaution, by manual means, including preparing and cleaning the surface for re-pointing/refilling of joints, including disposal of rubbish to the dumping ground within 50 metre lead.

Item No. 2 : Recess / Flush pointing on Red sand stone /Local stone masonry surface with lime, surkhi and marble dust mortar in the ratio of 1:1.5:1/2 {One lime: 1.5 surkhi (50% red and 50% light yellow surkhi ) : 1/2 marble dust}. (The rate is inclusive of all materials & labours involved except scaffolding).

Item No. 3 :Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : (In Cement Concrete)

Item No. 4 : Coursed rubble masonry (first sort) with hard stone in foundation and plinth with :Cement mortar 1:6 (1 cement : 6 coarse sand)

Item No.5: Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Item No.6: Disposal of moorum/building rubbish/malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge

Item No. 7: Removing mortar from and cleaning stones and concrete articles (net quantity of stacks of cleaned materials will be measured), (In cement mortar)

Item No. 8: Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of entering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Item No. 9: Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/m²

Item No. 10: Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.1.00 mm thick with zinc coating not less than 275 gm/m²

Item No. 11: Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:( GS Sheet)

Item No. 12: Stone work in plain ashlar in super structure upto floor five level in cementmortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment matching the stone shade : Both face dressed (Red/Buff sand stone of matching colour and textures) as per the direction of the site in-charge.

Item No. 13: Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. (Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix),

Item No. 14: Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above

Item No.15: Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood

Item No. 16: Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Item No. 17: Providing and fixing stainless steel (Grade 304) structure as per approved design for NB/Direction Board/Visitors Information board, made of Hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same in a pit (0.3X0.3X0.4)m with necessary earth work and cement concrete (1:2:4). Write up of the PNB should be trilingual (Odia, Hindi and English) as per approved matter and etching in nature on the 18 gauge SS sheet (3'X2') including dismantling the old PNB wherever required and carriage to the office with suitable arrangement etc all complete as per approval of Engineer-incharge

Item No. 18: Providing stone work in plain ashlar with machine cut laterite stone in cement mortarCement mortar 1:3 (1 cement : 3 coarse sand), after necessary PCC work (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) below the foundation for Cultural Notice board. RCC slab in inclined manner should be provided on the top of the stone structure as per approved design. 30 mm sand stone veneering work of backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade should be provided. Trilingual wite up of the CNB should be etching in nature on 18 gauge SS sheet (304 grade) (900mmX600mm) and each language should be etched in seperate SS sheet with approved write up and fixed on the top of the sand stone veneered CC slab etc all complete as per direction of the EIC

Item No. 19: Providing & fixing of buff sand stone benches having 4 legs of size (0.26x0.26x0.45)m with simple moldings and 8cm thick buff sand stone top size 1.50x0.60 m as per design and matching to the exProviding & fixing of buff sand stone benches having 4 legs of size (0.26x0.26x0.45)m with simple moldings and 8cm thick buff sand stone top size 1.50x0.60 m as per design and matching to the existing pattern at site.

SHASANK SEKHAR NAYAK (BID ID -3183075)

UTKAL ENTERPRISERS (BID ID -3174278)

BIBHUDANANDA MOHANTY (BID ID -3182896)