KNMT 22-23- Construction of Knowledge centre at Sandhaipettai Market in survey no.52-1 in Tiruchengode Municipality

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Footing

PLINTH BEAM

Supplying and filling in foundation and basement with filling M sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Pest Control Providing pre-constructional anti-termite treatment including supplying of the chemical (Chlorophyriphos emulsifiable - with ratio 1:19 (one part chemical and 19 part water)) in sealed containers and diluting with ratio specified against each and injecting it creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the Top surface of consolidated earth on which apron is to be laid, surroundings of pipes and conduits etc. all complete as per specifications. Payment released in 3 stages equally. Area for Measurement will be Outer plinth area

Refilling with excavated earth in layers of 30 cm watered well rammed and consolidatred conforming to standard specification including labour charges as directed by Engineer in Charge

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials)

Foundation

Ground Floor

First Floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Basement

Ground Floor

First Floor

Brick Partition Walls using III class ground moulded chamber bricks of size 8 3/4"X4 1/4" X 2 3/4" in C.M 1:3 using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification - 10 sqm

Ground Floor

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Supplying and laying in flooring with fully polished Sinthetic Grey colour Granite stone of 10mm thick (average) of 2' X 1' in size laid in cement mortar 1:2 - 20 mm thick & pointed with same colour of cement etc., complete as per standard specification

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed. -100sq.m S.I.333

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Laying the Flooring with Anti skid coloured ceramic tiles of sizes 305mm X305mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:3 (one cement ,three sand) over 20 mm base layer plastering and pointing with white cement neatly as directed.

Dadoing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Supplying and laying rubberised inter locking paver block m40 grade providing and laying of 83mm thick high strength type confirming IS 15658-2006 of rubberised inter locking paver block in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying & fixing door shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete. FLUSH AND FOLDING DOORS (PWD SOR P.no.42 S.no.116)

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1 mm thick) of size 100 mm x 60 mm with a rebate of 30/ 35 mm x 15 mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc., PWD SOR P.NO.44 S.No.158

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification. PWD SOR Pg. No. 43 Sl.No.125 a

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work PWD SOR Pg. No. 66 S.No.266

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.PWD SOR Pg. No.65 S.No.265

Supply and erection of 6KW Solar On Grid Solar Rooftop System from Go Solar Solutions consists of following components.Make : Canadian Solar/Vikram SolarType : Poly-crystalline Power: 315/320/325/330 Wp (According to Availability)Quantity: 158 No Size : 2000mm x 1000mm (2 meters x 1 meters) Voltage : 440/220Volts On Grid Solar Inverter Make : Delta Inverter (German) Size : 50kW Phase : Three (3 Phase) Quality : Premium Quantity : 1 Unit Output : 440/230 Volts @ 50Hz Monitoring System : Yes (DelREMO-Delta Realtime Monitoring) Type : Wifi/Lan/GSM Mobile Apps : Yes Electrical Accessories (Compulsory) DC Distribution Box: Yes (Fuse+Surge Trap+MCCB Breaker) AC Distribution Box: Yes (Fuse+Surge Trap+MCCB Breaker) Mounting Structure: Type : Aluminium or Galvanized Angle : As per site requirement Design : Customized Wiring & Cabling Make : Polycab Material: Copper Size : 6mm2 Solar Power Output (Generation) Units per Day: 225 kWh Units Per Month : 6750 Units Units Per Year : 72,500 Units DC Side: Armoured Cable

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Supply delivery erection ,commisioning, testing and handing over of of 62.5KVA capacity Deisel Generator set 3 ph, 50 Hz,415 V, 1500 rpm with AMF panel as detailed belowconsisting of deisel engine capable of delivering Water Cooled Engine suitable for generator application with a shaft output of 43BHP at 1500rpm under NTP conditions as per BSS 5514/IS 10000. The Engine shall comprise the following standard scope of Supply (Kirloskar/Ashok Leyland/Equivalent) 1.Oil type Cleaner 2.Expansion below 3.Radiator,Radiator Fan and Mounting 4.Air toAir Charge Cooler 5.Exhaust gas turbo Charger 6.Lube oil coller and Lube oil filter 7.Fuel filter (Pre and Micro) 8.In-Line Mono block fuel injection pump with governer and fuel feed Pump 9. Electronic governor 10.12V battery charging Alternator 11.12 Bolt Electric starter motor 12.Engine test certificate 13.residential Muffler 14. Fly Wheel with starter ring.PWD SOR P.No.146 S.No.10.a

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase, STAIRCASEs using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete PWD SOR Pg. No.57 Sl.No.244

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Providing & fixing PVC RAIN WATER DOWN FALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes, Bemds, other clamps, screws nails etc., complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm](D)

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.(D)

110mm dia pipe

Supplying and fixing of 1000 litters capacity PVC/HDPE tank of approved quality including cost of all materials like tank fittings, lead .lift, errection etc complete. TWAD SOR PGNO:85 SL NO.17

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. (D)

25mm Gun Metal Valve

32mm Gun Metal Valve

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary (D)

SD Tap

Pillar Tap

P.V.C. Pipes (10Kg/SqCm) Supplying laying and jointing P.V.C pipes (10Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.(D)

25mm dia Pipe

32mm dia Pipe

Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements PWD SOR PG.NO:99 SI.NO:367

Coupler -25mm dia Pipe

Coupler - 32mm dia Pipe

Elbow - 25mm dia Pipe

Elbow -32mm dia Pipe

BEND-25mm dia Pipe

BEND-32mm dia Pipe

Tee-25mm dia Pipe

Tee-32mm dia Pipe

End Cap-25mm dia Pipe

End Cap-32mm dia Pipe

Reducer-25 mm x 20 mm

Reducer-32 mm x 25 mm

Reducer Tee -25 mm x 20 mm

Reducer Tee -32 mm x 25 mm

Reducer Elbow-25 mm x 20 mm

Reducer Elbow-32 mm x 25 mm

Jet Nipple -25mm dia Pipe

Jet Nipple -32mm dia Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).(D)

PVC Elbow -110mm dia

PVC Elbow with Door -110mm dia

PVC Tee -110mm dia

110mm dia

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications (D)

Supplying and fixing in position 15mm dia C.P.Shower rose & stop cock of approved make confirming to IS specifications and qulity including cost of Shellac thread etc. complying with standard specification. PWD sor pg.no:48

Supplying and fixing in position Indian make bewelled edge mirror of size 600 x 450mm quality including cost of Rawal plugs, brass screws. etc. complying with standard specification.(D)

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications(D)

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact(250lts)(PWD SOR PG NO 72 S.No.295 a

Supplying and fixing in position C.P. Soap tray of size 150 x 150mm including cost of teak wood plug and C.P. screws. etc. complete complying with standard specification.(D)

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings etc., complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank. . (D)

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings- 100 mm x 75 mm including all charges etc, complete as per standard specification.(D)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three Crushed stone sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.(D)

Conducting Geophysical survey, quality and quantity test and transportation charges etc, (This includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist)

Drilling of 150mm dia borewells

Drilling of 150mm dia borewells in overburden soil including labour charges for insertion of casing pipes.

Drilling of 150mm dia borewells in hard rock areas anywhere in Tamil Nadu including transportation to the worksite in hard rock areas and developing the bore wells

Supplying and delivery of Special Plain Blue 150mm dia Casing Pipes for Bore Wells. The rate including cost and conveyance of materials. Complete (TWAD SOR 2021-22 P.no.22 S.No.1.1

Supply of 150mm dia OD PVC End cap as per special specification. (TWAD SOR 2021-22 P.no.27)

THREE PHASE SUBMERSIBLE PUMPSET SUITABLE 50X75MM FOR 150MM DIA BOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARD clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continous rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of 5 HP direct online starter confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Labour charges for the erection of submersible pumpset in borewell / openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days. TWAD SOR 2021-22 P.no.287 S.No.17c.i

Supply and delivery of 40mm dia UPVC Column Pipe

Supply and delivery of PVC insulated and sheathed three core 4 Sq.mm Flat type copper cable conforming to IS 694/1990. Complete. (TWAD SOR 2021-22 P.no.116)

Supply and delivery of the following water supply materials with ISI make

8" bore Cap TWAD SOR 2021-22 P.no.278 S.No.1b

MS 32/40mm MS clamp set TWAD SOR 2021-22 P.no.44 S.No.5.1b

50mm dia GM Non return valve TWAD SOR 2021-22 P.no.45 S.No.5.2

12mm dia Nylon Rope for borewell

Supply and fixng of TNEB meter board suitable for 3phase 63A service connection made up of suitable angle iron frame work of size 2feetx1-1/2feet using angle iron of size1-1/2"x1-1/2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2feetx1/2feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos. 63A fuse units (500V), 1No.neutral link, copper earth flat of size 1"x1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete SD 129

Supply and laying of PVC insulated, PVC sheathed, armoured, LTUG Cable of size 2 core 10 Sqmm Al. cable clamped on Walls etc., Complete as per standard specification. (SD 210)

Earthing as per the ISI specification with an earth electrode of 2.10metre Class'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mmx50mmx6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry SD233

Supply, installation testing and commissioning of 5 KVA single phase Hybrid inverter with 2 hours battery backup, solar panel for 3 KW, suitable to connect with grid to transfer excesss power, 1 phase, 230 V single phase output, necessary protection, 40A incoming & outgoing MCB control, all connections, Junction Boxes, solar panel mounting supports, Inverter stand & all nessorary accessories (PWD SOR 2021-22 P.No.148)

Supply, conveyance, installation, testing and commissioning of 1200mm sweep -5star rated ceiling fan complete with 300mm down rod , canopies, shackles and blades and resistance type regulator working on 230V/240V single phase A/C, using standard accessories , wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required. SD 106

Supply, conveyance, installation, testing and commissioning of 450mm dia wall mounting fans of the following sizes using standard accessories excluding resistance type regulator, wiring with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring, mounting clamp etc., all inclusive as required. (Electrical SOR 2021-22 P.no.16)

Supply and fixing of 300 mm (12") sweep (light duty) 1400 RPM, AC exhaust fan complete without provision of holes in the wall SD 114

Supply, erection, testing and commissioning of 18W LED 3000K Square Type Recessed Fitting with LED suitable to iluminate wall / garden areas with tilting provision for angle adjustment, including all necessary accessories, juntion box. (PWD SOR 2021-22 P.No.115)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1 Nos x 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) SD 140

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box, modular plate, 6A switch and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. SD 23

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 14 SWG TC wire with painting of suitable colour SD 54

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with MS accessories in flush with wall with 150mm x 100mm x 75mm MS switch box concealed type with 3mm thick hylum sheet cover for 15A 3 pin flush type non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire and rnaking good of the concealed portion for concealed power plug point SD-15

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge MS coundit pipe on wall and ceiling with continous earth wire connection of 14 SWG TC wire with painting of suitable colour for Plug Point SD 44

Supply and run of 3 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable flexible conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting painting of suitable colour SD 48

Supply, installation and commissioning of conference type public address system projector with motorized screen including all material cost and all labour charges for assembling etc., (Electrical SOR 2021-22)

Chairman Unit

Conference Controller

PA Mixer Amplifier 240W

Wall Speaker 15W

Ceiling Speaker 15W

Cordless Mic UHF

8 Pin Conference Mic Socket with Modular Box and Front Plate

2 Core 1.5 sq.mm Shielded Copper Speaker Wire

3600 Ansi Lumens Projector, XGA (1024X 768 ) Resolution, Contrast Ratio: 20000:1

10’ x 8’ Motorized Screen

3 Feet Ceiling Mount Kit

20 Metre HDMI Cable

3 Core 1.5 sq.mm. PVC Power Cable for Projector

Supply and fixing 16amps DP switch with metal clad (side handle) of 500 V with F & N on suitable teak wood Board of size 30cmx20cmx6 cm including necessary internal conection,earth connection etc.,complete (SD 142)

Supply an fixing of 6way SPDB of 16A /way with 16ADP switch with metal clad of 500V with fuse and neutral (sidehandle) on suitable angle iron frame work with trunking box MS cableen try box with PWD earthing (SD 153)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with doubledoor (metal) 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall andmaking good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISImark (like standard make) (SD167)

Supply and fixing of 32A TPNMC switch with suitable angle iron frame work with MS cable entry boxes with earth connection only (SD164)

4 Core 16 sq.mm. PVC Armoured UG Cable (SD 203)

4 Core 10 sq.mm. PVC Armoured UG Cable (SD202)

Supply and fixing of brass cable gland for 4 x 25 sq.mm. PVC LTUG aluminium armoured cable with earth connection. (SD185)

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with earth connection (SD186)

Supply and installation of ground mounted 8 mtrs octagonal pole with light fitting supporting single arm, concealed M.S. box for looping incoming & outgoing cable, etc. The pole shall be manufactured from HT steel in octagonal shape & pole shaft to withstand maximum wind speed as per IS 875. The pole shall be Hot Dip galvanised with average coating thickness of 70 micron. The mounting bracket shall be bolted type suitable for single light fitting. The pole shall be tapered with single longitudinal welding and shall be Hot Dip galvanised in single process. The pole shall be ground level mounted with foundation bolts, Rate shall be inclusive of all connected civil works, foundation, suitable concealed IP65 M.S. box with openable top cover in flush with the surface of the pole for looping of incoming cable, anti corrosive polyurenthene based painting treatment complete with surface treatment, finish painting, etc. with necessary connector block, 6A SP MCB switch, wiring from M.S. box upto fitting by 3 core 2.5 sqmm. 8 Metre Length Single Bracket Pole with Base Plate (300 x 300 x 6mm) 139.70mm OD x 4.50mm Thick x 5200mm Length, 114.30mm OD x 4.50mm Thick x 2400mm Length, 88.90mm OD x 3.25mm Thick x 2400mm Length PVC sheathed FRLS wire, foundation base plate, light fitting bracket assembly etc. (PWDSOR-Page-150)

Coil earth to light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth (SD78)

Supply delivery and fixing of 48W LED Street Light Fitting with LED light. PWD SOR 2021-22 P.No.115 S.No.17.b

SMART CLASS : Supply of smart panel display : Panel size 75" Type/Tech - TFT LCD Module with LED Backlight display area (mm) 1650.24(H) *928.26(V), Aspect ratio 16:09, Native resolution 3840*2160 (4K), colors 1.307 Billion, Brightness 370 nits (typ), contrast ratio 4000:1 Typ., Response Time - ams, Refresh Rate 60Hz, Viewing Angles - H = 178, V-178Typ, Backlight life - 30000 Hours Typ., Glass thickness 400, Glass hardness 9H (pencil), 7 (Mohs), surface Treatment Antiglare (7H), Orientation Landscape, Operating System - Windows PC built in compatibility CVBS 480i, HDMI 480i, 480p, 720p, 1080p,1080i, Type A x 2 (2.0) x XL (3.0) Type B x2, for touch operating condition : Temperture (2C) 00 C to 400 C, Humidity 20% - 80% non - considering Power : Voltage AC 100-240V, 50/60Hz, consumption 220 (typ) < 0.5 W ("Standby Mode"), Main Power Switch : Yes, Ergonomics: Tilt 800*400, wall Mount Bracket 3rd party stand, Touch type / Tech, Touch Resolution 32767 x 32767, Touch Point 20 Point, OS Support Windows, Mac, Input HDMI 1.4 & 2.0 x 3 (2.0*2 in rear side 1.4*1 in front), RCB / VGA XL, YPbPr xl, YPbPr xl, MIC (Microphone) XL, RS232 XL, Audio XL PC audio (3.5mm)

Supply and Fixing of CCTV Camera with Specification of Dahua- HAC-HFW 1100DP-B-0600 720P 1 Mega Pixel Analog High Definition camera, outdoor-25/30 fps@720P,1/2.9" 1 Megapixel CMOS, 50m IR,ICR, 6mm Lens optional, IR Bullet Dahua - Channel - AHD, High Video Quality on HD 1080N, Transmit Video Signal, audio signal & Dual way data communication signal over one coaxial cable, HD Video transmission without Video quality loss & delay, extremely, long transmission distance (300), as directed by Departmental Executive Engineer.

Supply and Installing CCTV camera LMR

40" Led TV for display LMR

29" Led TV for display LMR

16 Channel - 2 SATA (2 Nos. Hard Disk) PWD SOR 2021-22 P.No.154 P.No.34.C

Rack With Accesssories -4U As per PWD SOR P.No.155 S.No.39.a

Armoured LAN & CCTV CAT 6 Cable As per PWD SOR P.No.153 S.No.29.a

PoE SWITCHES FOR CCTV IP CAMERA 24 Port PWD SOR 2021-22 P.No.154 P.No.33.C

HARD DISK FOR NVR 8TB PWD SOR P.No.155 S.No.38.d

RACK WITH ACCESSORIES 12u PWD SOR P.No.155 S.No.35.e

Brick jalli wall - Construct exposed brick jalli wall with standard wire cut bricks and use CM 1:6 (one cement & Six sand), size of 9"x 4 3/8 " 2 3/4" including finishing, curing, etc., complete complying with standrad specification

Brick work for seating - Construct 115mm thick brick wall of with standard wire cut bricks and use CM 1:6 (one cement & Six sand), size of 9"x 4 3/8 " 2 3/4" including finishing, curing, etc., complete and fill with approved coarse rubbles for filling.

Brick work for seating - Construct 230mm thick circular brick wall of with standard wire cut bricks and use CM 1:6 (one cement & Six sand), size of 9"x 4 3/8 " 2 3/4" including finishing, curing, etc., complete and fill with approved coarse rubbles for filling.

Counter top - Providing and fixing of 2 inch thick natural stone Cuddapah equivalent to the prescribed size and shape with cement Grout 1:6 as instrcuted by site engineer

Seating area - Providing and fixing of 1 inch thick natural stone Cuddapah equivalent to the prescribed size and shape with cement Grout 1:6 as instrcuted by site engineer

Supply and delivery of childrens Outdoor play materials.

TIC TAC TOE

Abacus

Mirror Maze

Marble panel

Sign language panel

Interactive panels

Supply, delivery and installation 24-dp 1802 / i5 processor / 8GB RAM / 11th Gen core /500Gb HDD / DVD RW / HP 19.5" wide LED Monitor / HP USB Keyboard and optical mouse / three years onsite OEM Direct warrenty including GST Charges of 18% etc., Complete as per standard specifications

SRI JAYABALAAJI BUIDERS