SPECIAL REPAIR TO BLDG NO T 55 AND T-53 UNDER AGE BR - I OF GE WEST MATHURA

Amount

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified and directed by Engineer-in-charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed.

Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section in framed work, in any position complete all as specified and directed.

Demolition of Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work cement concrete (reinforced) complete all as specified and directed.

Dismantling of wall and ceiling boards of any type and any thickness including cover fillets complete all as specified and directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified and directed by Engineer-in-charge.

Dismantling of cast iron pipes jointed in cement mortar and takin out from trenches, wall etc up to 100mm bore pipe complete all as specified and directed.

M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 13.00 here-in-before but except brick. Note : Old serviceable brick retrieved from serial item No 2.00 of BOQ here-in-before shall be used under this item.

S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

M&L for cement concrete type C-1, (1:3:6) using 20mm graded aggregate as in bed block or filling of chowkhats including necessary form work complete all as specified and directed.

M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed.

S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 30mm thick factory made solid PVC moulded door shutter with particle board core with 5mm thick PVC moulded sheet on the front face and 5 mm thick PVC plain colour sheet on back face complete all as specified and directed by Eng-in-charge.

M&L for Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 incl portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilator shutters side hung type without sash, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips rubber packing, anodised aluminium snap beading screws Anodise aluminium fitting such as peg stays 150 mm long (1 No ), including pag stay and hinges type B-21 100 mm long (2 No) and suitable handle (1 No) complete all as specified and directed.

S&F powder coated Anodised aluminium door section, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws Anodise aluminium fitting such as including hinges 100 mm long (2 no) and suitable handle(2 No) complete all as specified and directed.

M&L for aluminium grill mesh made out of 6mm dia having girth not exc 25mm both ways fixed with aluminium cleat to window frame complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood plain solid in truss, purlin, straight chowkhat and frames wrought, frame rebated on the solid, rounded or chamferred put together with glue pinned at joints etc complete all as specified and directed.

Fixing only 2nd class hard wood plain solid in truss, purlin, straight chowkhat and frames wrought, frame rebated on the solid, rounded or chamferred put together with glue pinned at joints etc complete all as specified and directed. Note : Old serviceable 2nd class hardwood retrieved from serial item No 8.00 of BOQ here-in-before shall be used under this item.

S&F steel work in tubular trusses including columns, special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1998 grade St-240 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of red colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, overall size 915mm x 460 mm / (36" x 18") bowl size 410mm x 355mm / (16" x 14") and depth 175mm / (7") including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated 32mm bore with long screwed shanks and fly nuts including making holes in brick walls for brackets and fixed in CM (1:3) or PCC 1:2:4 type B0 complete all as specified and directed by Engineer-in-charge. Make :- Nirali model Elegance (Glossy) / Prayag model No 1128-D Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd) model No SSSB-52 (Glossy) or equivalent in makes mentioned in Appendix 'A' here-in-after. Note :- Size of sink for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide sink as per cat No mentioned against make of sink. where cat No is not mentioned against any make, in that case sink of size mentioned in description has to provide, if exact size of sink is not available, then next higher size sink has to be provided. Nothing extra shall be paid on this account.

S&F in repairs stainless steel Kitchen plate rack overall size 900mm x 900mm make out of 0.8mm thick stainless steel sheet etc. complete all as specified and directed.

S&F 5.5 mm thick plain glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane.

S&F Sheet glass 4 mm thick in glazing to aluminium door, window & partition including pad, gasket complete all as specified and directed.

S&F Mortice latch with two levers (vertical type), aluminium, anodised body and fixed complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 300 mm aluminium alloy, anodised sliding door bolts with hasp, staple and fixing clips of sheet, cast or extructed section and fixing bollts and sliding bolts of extruded section or cast aluminium ally and fixed complete all as specified and directed.

S&F Aluminium handles cast type anodised of size 125mm size, complete all as specified and directed.

S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1, using 20mm graded stone aggregate for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and other similar works complete all as specified and directed and directed.

M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1, using 20mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified and directed and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished of flat surface complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. for rough finished surface of concrete complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

M&L for vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed.

All as per item No 52.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for vitrified paving tiles (any colour) of size 30cm x 30cm x 10mm thick, with gray cement & pigment set, jointed and pointed in neat cement slurry in floors laid over and including 15mm screed bedding in cement mortar (1:4) complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block with grey cement & pigment any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

M&L for sand filling under floors or in foundation complete all as specified and directed.

M&L 100 mm thick Cement concrete type D-2, (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, coping, parapets and railing upto 60cm height, copings bed block,roof kerbs or mud stops, kerb stone, kneelers, apex stones, bed plates, surface channels and drains, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type C2 1:3:6 (40 mm grade aggregate) in surface channel & drain complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. complete all as specified & directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface,finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed.

Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

M&L for Cutting chases, pinning in, making good to facing where required & pointing in CM 1:3 for conc water tubing and like not exc 10CM girth in brick wall etc complete all as specified and directed.

S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed.

S&F 20mm dia PTMT ball PVC valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Eng-in-charge.

S&F in repair 20mm Gate valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete all as specified and directed.

S&F PVC (SWR) 100 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore junction single, (Single T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) 110mm bore junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed.

S&F 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for repair 32mm Waste fittings, brass, chromium plated for glazed ware wash hand basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified

S&F in repair chromium plated shower rose with or without swivel joints including fixing to steel pipe of 100 mm size complete all as specified and directed by Eng-in-charge.

S&F in repair CP Jet spray butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed by Eng-in-charge.

S&F in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore CP angle valve, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F in repair 15 mm dia stop cock fancy type, chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs peg set of five of stainless steel bright finished, fixed complete all as specified and directed by Eng-in-charge.

S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge.

S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge.

S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed.

S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

S&F Factory made box type steel windows with hung shutters both glazed and guaged shutter frame 60x25 mm ERW hollow 'P' section with wall thickness not less than 1mm fixed to pressed steel frame 120mm x 70 mm x 1.6mm thick including fixing glazed portion, iron grills 8mm square MS bar hunges with steel handle and fitting, lugs etc, including one shop coat of primer complete all as specified and directed.

M&L preparation of new plastered surfaces and applying two coats of exterior weather coat and primer on walls all as specified.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer and a coat of wall putty to achieve smooth finish complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surface of walls and applying two coat of distemper oil emulsion distemper on wall incl applying a coat of wall care putty to achieve smooth finish to wall etc complete all as specified and directed.

M&L for complete removal and preparation of old painted surfaces of wall and applying two coat of exterior emulsion paint complete all as specified and directed.

S&F in repairs curtain rod, stainless steel of 25mm dia with fixing brackets stop rollers etc fix complete all as specified and directed.

S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Eng-in-charge.

M&L for bands, straps, supports or stays for rainwater, Ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and lintle hanges, large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters ; knee piece inserts; two way and three ways straps , plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge.

S&F in repairs toilet paper holder of mild steel chromium plated 'D' type fixed to walls with chromium plated brass screws, complete all as specified and directed.

S&F in repair Glass shelf 450mm long x 100 mm wide including brackets fixed to wall with sleeves and screws complete all as specified and directed.

S&F in repairs chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge.

S&F in repair stainless steel grating 100mm bore size fixed with white cement complete all as specified and directed by Eng-in-charge.

S & F 605X605 mm size of grid GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended form soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. GI (up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40X 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia. 40 mm long etc complete all as spd and as directed. Incl providing and fixing coloured designer board 4 mm thick in ceiling fixed with screw as per manufacturer's instructions complete all as specified and directed by Eng-in-charge.

S & F 605X605 mm size of grid GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended form soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. GI (up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40X 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia. 40 mm long etc complete all as spd and as directed. Incl refixing old (retrieved from serial item No 10.00 of BOQ) serviceable board 4 mm thick in ceiling fixed with screw as per manufacturer's instructions complete all as specified and directed by Eng-in-charge.

S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet, heavy duty as per sample approved by GE, inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed.

S& F 18 mm thick Alstone Hybrid Water Proofing Board in cupboard shutter with decorative on one side & other side balancing white fixed by drilling screws complete all as specified and directed by Engr-in-charge.

S&F 100mm long stainless steel handles, oval type complete all as specified and directed.

S & F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised 30 mm Width of flaps (when open) in mm all as specified all as directed.

S&F Magnetic catcher fixed in with nut,screw washer complete all as specified and directed by Eng-in Charge.

S&F door closer hydraulically regulated designation No. 3 universal type cast iron body suitable for door shutters of 851 to 1000mm in width and fixed complete all as specified and directed by Eng-in-charge.

S&F 300mm mild steel (Helical door spring) ordinary rat tail rod pattrern spring including roller and roller plate complete with necessary welding work complete all as specified and directed.

Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed.

M&L for Point wiring complete with 2.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 2.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

All as per serial item No. 124.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board.

All as per serial item No. 124.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches.

M&L for point wiring with 2.5 sqmm PVC insulated, unsheathed FRLSH multistrand copper conductor cable 1100 volts grade drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all and including conduit fittings and fixing accessories 1.2mm thick sunken anodised pressed steel terminal boxes with 3.0 mm thick hylam sheet cover for mounting switches, socket etc including 2.5 Sqmm FRLSH multistrand copper conductor cable as continuous earth wire complete for one socket 16 Amp socket outlet controlled by one switch on independent board complete all as specified and directed.

M&L for Sub main wiring with 2 runs of 6 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 6 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length.

S&F switch piano flush button single pole, one way 5 Amp 240 Volt complete all as specified and directed.

S&F switch piano flush button single pole, one way 15 Amp 240 Volt complete all as specified and directed.

S&F socket outlet 6 amps 5 pin flush type, 230 volts complete all as specified and directed.

S&F socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type 230 volt complete all as specified and directed.

S&F in repair sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 Volt complete with one single pole MCB of cap 20/25 A, C series complete all as specified and directed.

S&F ceiling rose 63x30 mm three terminal, polycorbonate body complete all as specified and directed.

S&F fan regulator electronic, five step type hum free suitable control speed of fan from 0 to 100% and connecting electrically all as required complete all as specified and directed.

S&F Angle / batten holder polycorbonate type body suitable for batten fitting complete all as specified and directed.

S&F LED bulb of capacity 10/12 watts not less than 700 lumens output at 6500K colour temp, complete all as specified and directed.

S&F in replacement surface and wall mounted 20 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed.

S&F in replacement 10W integrated LED bulk head luminaire environment friendly, ultra modern, energy saving, surface mounted decorative oval bulk head with LED light, complete all as specified and directed.

S&F in replacement surface and wall mounted 10 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed.

Supply and fixing in replacement of burnt conventional fans with BLDC ceiling fans, 5 star rated by Bureau of energy with service value of not less than 8.40, (26W±10%) with or without remote, with rated speed 350 Rev per min, air delivery 220 Cum/min complete with blades, down rods, electronic regulator and accessories, 230 volt, 1200 mm sweep, suitable for single phase supply complete all as specified and directed. Note : Old unserviceable ceiling fan shall be deposited in AGE E/M store yard.

Supply and fixing in replacement Exhaust fan metallic body of size 300 mm sweep, 50 Hz, AC 240Volt, 900 RPM, dynamically balanced impellers for smooth & vibration free operation, pre-lubricated double ball bearing for maintenance free running with aerodynamically designed & balanced blade, air delivery 1275 Cum/hr, noise level 40dB- 45dB and power consumption (50 W±10%) heavy duty single phase supply including mild steel louvers all as specified and directed. Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard.

Supply and fixing in replacement Geyser 25 ltr capacity in 5 Star rating, digital display, feather touch panel, shock safe plug, incoloy glass coated element, feroglass technology, PUF insulation 0.8 Mpa high working pressure, Whirlflow technology, IPX-4 protection suitable for, 50 Hz, AC 240Volt, single phase supply, white blue with overall length approx 620 mm with wall mounting accessories & 02 Nos flexible pipe connections all as specified and directed. Note : Old unserviceable geyser shall be deposited in AGE E/M store yard.

M&L for cutting existing tubing and taking up for tapping/termination of pipe line, screwing including existing steel tubing of size 15mm dia complete all as specified and directed.

S&F in repair building security light of 30 Watt New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source and electronic driver including all fixing arrangements complete all as specified and directed.

Supply & fixing in replacement ceiling light with 36W Watt, 6000 K, slim LED panel 2' x 2' LED panel for recessed on ceiling) dust-free installation with high brightness LEDs for glare-free homogenous illumination with driver and all other connected accessories complete all as specified and directed.

Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply & Fixing in replacment MCB SPN, 240 Volts, 32 Amps breaking capacity 10 KA, 'C' curve complete all as specified and directed.

Supply & fixing in replacement of MCB single pole 240 volt any rating from 6 to 32 amps, B series with rupturing capacity 10 KA complete all as specified and directed.

Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core including taking out old unserviceable cable complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground not less than 2.25 mtrs deep below normal ground level with top edge of the plate not less than 1.5 mtrs below normal ground level, surrounded from all sides with mixture of charcoal and common salt, connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel protected by galvanised iron light grade 15 mm dia pipe and GI pipe 20mm light grade for water filling including 15x20mm reducer socket funnel wire mesh, RCC cover with concrete 1:2:4 using 8 mm# bar@100 mm c/c both ways ,PCC chamber pit with PCC (1:3:6) type C-2 and excavation and earth work,disposal of suplus spoil to a dstance not exceeding 50mtrs all as specified and shown on electrical plate No. 3 of 2009 (Part-I) complete including taking down old unserviceable earthing complete all as specified and directed. Note :- The unit rate includes for protection pipe and GI wire 4mm dia from top of earth plate up to 7.5 meter above ground level.

B S ENTERPRISES (BID ID -3104904)

mh enterprises (BID ID -3104961)

VANI CONSTRUCTION (BID ID -3102202)

Ahmed constructions (BID ID -3111234)

VASUNDHARA AND COMPANY (BID ID -3104788)

Deepak Saxena (BID ID -3103318)

BHARDWAJ CONSTRUCTIONS (BID ID -3118476)