REPAIR/MAINTENANCE OF SECURITY LIGHT AND CONNECTED ITEMS AT BHISIANA IN DOMESTIC AREA UNDER GE (AF) BHISIANA

Material and labour for repair, maintenance and restoration of LED light fitting any wattage such as street lights, security lights, flood lights or any other type of external led light fitting, whether fixed in position on poles, high masts, buildings/structures or other supports, including carrying out the work in position or taking down the light fitting to ground level wherever required, inspection and testing of all components, parts, wiring and electrical connections, identification and rectification/replacement of defective components such as electronic drivers, connectors, terminals and other minor components, checking and tightening of loose connections, tightening of loose fitting, replacement of nut bolt, checking and rectification of incoming and outgoing wires at junction boxes, minor repair of wiring and connections, minor repair and maintenance of street light control timer, junction box and associated fittings, including refixing and securely restoring the light fitting to its original position after completion of repair, testing for proper functioning and illumination, complete in all respects as specified and directed by the Engineer-in-Charge. Note: (i) The quoted unit rate shall be deemed to include the cost of all labour, tools, tackles, lifting/access arrangements, taking down and refixing of light fittings, and all minor consumables and components, including electronic drivers, connectors, terminals, lugs, insulation tape and other incidental items required for completion of the work. (ii) Only the repaired light fitting shall be measured and paid for under this item. No separate payment shall be admissible for inspection, checking, tightening of loose connections, tightening of fittings, or minor repairs carried out in junction boxes, timer/control boxes or other common control arrangements serving one or more light fittings, the cost of which shall be deemed to be included in the quoted unit rate. (iii) In case replacement of an MCB is required, the same shall be measured and paid for separately under the relevant BOQ item.

Material and labour for repair, maintenance and restoration of light fitting other than LED any wattage such as street lights, security lights, whether fixed in position on poles, buildings/structures or other supports, including carrying out the work in position or taking down the light fitting to ground level wherever required, inspection and testing of all components, parts, wiring and electrical connections, identification and rectification/replacement of defective components such as choke (ballast), igniter, capacitor, lamp, lamp holder, connectors, terminals and other minor components, checking and tightening of loose connections, tightening of loose fitting, replacement of nut bolt, checking and rectification of incoming and outgoing wires at junction boxes, minor repair of wiring and connections, minor repair and maintenance of street light control timer, junction box and associated fittings, including refixing and securely restoring the light fitting to its original position after completion of repair, testing for proper functioning and illumination, complete in all respects as specified and directed by the Engineer-in-Charge. Note: (i) The quoted unit rate shall be deemed to include the cost of all labour, tools, tackles, lifting/access arrangements, taking down and refixing of light fittings, and all minor consumables and components, including choke (ballast), igniter, capacitor, lamp, lamp holder, connectors, terminals, lugs, insulation tape and other incidental items required for completion of the work. (ii) Only the repaired light fitting shall be measured and paid for under this item. No separate payment shall be admissible for inspection, checking, tightening of loose connections, tightening of fittings, or minor repairs carried out in junction boxes, timer/control boxes or other common control arrangements serving one or more light fittings, the cost of which shall be deemed to be included in the quoted unit rate. (iii) In case replacement of an MCB is required, the same shall be measured and paid for separately under the relevant BOQ item.

Supply and fixing in replacement of energy-efficient LED security light fitting/street light of 60 Watt, complete with pressure die-cast aluminium housing/body with top-opening driver cover for easy maintenance, heat-resistant clear toughened glass and suitable optical system for uniform distribution of light, complete with LED module, LED driver and all necessary internal components, terminals, connectors. The work shall include taking down and removing the existing defective/obsolete light fitting of any make and condition, whether fixed in position on poles, high masts, buildings/structures or other supports, fixing the new LED light fitting on the existing suitable bracket/support, making necessary electrical connections, proper alignment and adjustment, testing for satisfactory illumination and ensuring proper and safe functioning of the complete fitting, complete in all respects as specified and directed by the Engineer-in-Charge. Technical specification :- (a) Lumen system efficacy of luminaire should be minimum 120 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range: Minus 10°C to Plus 50°C (d) Power factor: Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Minimum 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing in replacement of energy-efficient LED security light fitting/street light of 45 Watt, complete with pressure die-cast aluminium housing/body with top-opening driver cover for easy maintenance, heat-resistant clear toughened glass and suitable optical system for uniform distribution of light, complete with LED module, LED driver and all necessary internal components, terminals, connectors. The work shall include taking down and removing the existing defective/obsolete light fitting of any make and condition, whether fixed in position on poles, high masts, buildings/structures or other supports, fixing the new LED light fitting on the existing suitable bracket/support, making necessary electrical connections, proper alignment and adjustment, testing for satisfactory illumination and ensuring proper and safe functioning of the complete fitting, complete in all respects as specified and directed by the Engineer-in-Charge. Technical specification :- (a) Lumen system efficacy of luminaire should be minimum 120 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range: Minus 10°C to Plus 50°C (d) Power factor: Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Minimum 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing in replacement of energy-efficient LED wide-angle flood light fitting of 80 W capacity, complete with suitable LED driver, epoxy powder-coated pressure die-cast aluminium alloy housing/body and front cover of clear heat-resistant toughened glass, suitable for outdoor applications, including LED module, optical system, heat dissipation arrangement, terminals, connectors, gaskets and all necessary internal components and accessories. The work shall include taking down and removal of existing defective/unserviceable flood light fitting of any make and condition, wherever fixed, and fixing the new flood light on the existing suitable bracket/support, replacement of nut-bolts if required, including necessary electrical connections, proper alignment and adjustment for required wide-angle illumination, testing and commissioning, complete in all respects as specified and directed by the Engineer-in-Charge. Technical specification :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : More than 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply and fixing in replacement of energy-efficient LED wide-angle flood light fitting of 120 W capacity, complete with suitable LED driver, epoxy powder-coated pressure die-cast aluminium alloy housing/body and front cover of clear heat-resistant toughened glass, suitable for outdoor applications, including LED module, optical system, heat dissipation arrangement, terminals, connectors, gaskets and all necessary internal components and accessories. The work shall include taking down and removal of existing defective/unserviceable flood light fitting of any make and condition, wherever fixed, and fixing the new flood light on the existing suitable bracket/support, replacement of nut-bolts if required, including necessary electrical connections, proper alignment and adjustment for required wide-angle illumination, testing and commissioning, complete in all respects as specified and directed by the Engineer-in-Charge. Technical specification :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : More than 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply and fixing in replacement of energy-efficient LED wide-angle flood light fitting of 150 W capacity, complete with suitable LED driver, epoxy powder-coated pressure die-cast aluminium alloy housing/body and front cover of clear heat-resistant toughened glass, suitable for outdoor applications, including LED module, optical system, heat dissipation arrangement, terminals, connectors, gaskets and all necessary internal components and accessories. The work shall include taking down and removal of existing defective/unserviceable flood light fitting of any make and condition, wherever fixed, and fixing the new flood light on the existing suitable bracket/support, replacement of nut-bolts if required, including necessary electrical connections, proper alignment and adjustment for required wide-angle illumination, testing and commissioning, complete in all respects as specified and directed by the Engineer-in-Charge. Technical specification :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : More than 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Material and labour for electric connection of street light with and including by using two core (2x1.5sqmm) high-conductivity multistranded annealed copper (Class 5 flexible) flat/round cable, PVC insulated and overall PVC sheathed, 1100 volt Conforming to IS 694 : 2010, from junction box to light fitting drawn through existing protection pipe, including taking down old connection wire of any size and condition complete all as specified and as directed. Note :- Protection pipe where required shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in replacement security light fitting bracket made out of GI tubing light grade 50mm dia, 1.5 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron of size 25x4 mm with suitable nuts and bolts for holding/fixing of bracket on steel/PCC pole including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement security light fitting bracket made out of GI tubing light grade 40mm dia, 1.5 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron of size 25x4 mm with suitable nuts and bolts for holding/fixing of bracket on steel/PCC pole including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.