Electrical Installation for Renovation of Research Lab No.1 (Room No 317) at 2nd floor of Chemistry department in P.U Campus, Sector-14, Chandigarh

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable etc. as required (Ref to DSR 1.8)

Group C (Ref to DSR 1.8.3)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. (Ref to DSR 1.17)

3 x 2.5 sq. mm (Ref to DSR 1.17.12)

3 x 4 sq. mm (Ref to DSR 1.17.21)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in urface/recess including cutting the wall and making good the same in case of recessed conduit as required (Ref to DSR 1.21)

25mm (Ref to DSR 1.21.2)

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required (Ref to DSR 1.23)

5/6 A switch (Ref to DSR 1.23.1)

3 pin 5/6 A socket outlet (Ref to DSR 1.23.4)

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required (Ref to DSR 1.30)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (Ref to DSR 2.4)

4 way (4 + 12), Double door (Ref to DSR 2.4.1)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Ref to DSR 2.10)

Single pole (Ref to DSR 2.10.1)

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required. (Ref to DSR 2.16)

Providing and fixing 6 SWG dia G.I. wire on surface or in recessbfor loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required (Ref to DSR 5.18)

Providing, fixing, testing & commissioning of 63 amp MCB TPN, 10kA, 'C' curve in the existing distribution board, complete in all respect to the entire satisfaction of engineer in-charge. (Ref to N.S.)

Fabrication and Erection of "D" Type Fan Hook. The Fan Hook should be fabricated with M.S bar 1/2" mounted on M.S Clamp having provision of 4 Nos Fasteners. The fan hook should be painted white in color after applying primer and should be installed at site with 4 Nos fastners complete in all respect to the entire satisfaction of the EIC. (Ref to N.S.)

Supplying and fixing 100W socket type 5 step fan regulator on existing plate with all petty materials complete in all respect to the entire satisfaction of the EIC. (Ref to N.S.)

Supply and laying of XLPE insulated PVC inner sheathed aluminum conductor Un-armoured (3.5 core) cable of size 25 sqmm on wall surface complete in all respect to the entire satisfaction of the EIC. (Ref to N.S.)

Providing, Installation, Testing and Commissioning of 1200 mm sweep, BEE 1 star rated (min), ceiling fan, double ball bearing, 100% copper wound motor with 3 nos. blades, down rod as per site requirement, 2 nos. canopies, shackle kit, safety rope, Power Factor not less than 0.9, Air delivery minimum 210 Cum/Min, THD less than 10%, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. (Ref to N.S.)

Supplying, installation, Testing & Commissioning of Panel light 36 Watt, 1x4 ft., with Driver (Ref to DNIT item No. 15)

Supply and Erection of Exhaust Fan (Heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making good the damage, carriage charges, connection, testing, commissioning etc as required to complete the job to the entire satisfaction of the EIC. (Ref to N.S.)

380MM Sweep 900RPM (min) with louver. (Ref to N.S.)

Please Enable Macros to View BoQ information