Provision of surveillance system in SLF Ghazipur

Amount

Part A: Survillance S/I/T/C of 2MP varifocal lens Bullet IP Camera with following specifications:- Image Sensor: 1/2.8 2MP CMOS or better** Minimum Illumination: 0.1 lux color, 0 lux with IR or better ** Shutter Speed:1/3 – 1/100,000 s Frame Rate:25 fps or better ** Lens: 2.8 to 12mm Varifocal lens Video Compression: H.265 or better ** S/N Ratio: >45dB Resolution: (1920x1080) or better Protocol: should comply to IPv4/v6, TCP/IP, HTTP, HTTPS, FTP, PPPoE,DDNS, IEEE802.1X IR Range: Minimum 20m Operating Temperature: -20 to 55 deg Cent Weatherproof Standard:IP66 or better ** Safety standard: UL

S/I/T/C of 4MP PTZ Camera with following specifications:- Image Sensor: 1/2.8 2MP CMOS or better** Minimum Illumination: 0.1 lux color, 0 lux with IR or better ** Shutter Speed:1/3 – 1/100,000 s Frame Rate:25 fps or better ** Lens: 30 X ZOOM Video Compression: H.265 or better ** S/N Ratio: >45dB Resolution: (1920x1080) or better ** Protocol: should comply to IPv4/v6, TCP/IP, HTTP, HTTPS, FTP, PPPoE,DDNS, IEEE802.1X IR Range: Minimum 20m Operating Temperature: -20 to 55 deg Cent Weatherproof Standard:IP66 or better ** Safety standard: UL

Supply and installation of PoE switch having the speed of minimum 1 GHz or better with 10/100/1000 base Tx PoE Port, 1 no. dual personality Gbe Port for copper/fiber uplink, 3.7 Gbps switching capacity, 2.7 MPPS forwarding rate. The PoE should have the PoE +facility to drive all the cameras etc. as required of following ports 8 port

SITC IP65 box (without PoE switches)of dimention 310mmX160mmX140 mm on pole or wall with suitable arrangement for support/installation of 8 port Giga PoE switch and 1 nos. 15/16 amp modular switch socket set

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supply Installation testing and Commissioning of Pigtails 1 meter with Splicing and testing.

Supply Installation testing and Commissioning of optical media converter gigabit sc type up to 10 km single mode

Supply Installation testing and Commissioning of LIU boxes complete with all accessories etc. as required of 12 ports

Supplying and laying of Optical Fiber Single Mode Cable (6-Fiber) on surface or in existing conduit etc complete i/c connections etc complete as required

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm. ARMOURED

Supplying and fixing OF WIRELES POINT TO POINT LINK FOR 100 MPS WITH ALL PROGRAMMING FROM 2KM DISTANCE

PART B: Pole arrangement and allied work Fabrication, supply & erection of following size flange mounted hot dip galvanized octagonal pole made from HT steel plate, window with flash cover with full verticle window cover at appropriate height from the base plate on existing cement concrete pedestal as required. i/c supplying and fixing of 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. GI strips 4 mm thick of suitable length and having suitable size tapped holes as reqd, terminal block suitable for 25 sq mm conductor – 4 nos. & shorting links on DIN channel i/cpdg and fixing DIN channel of suitable length,, 6 Amp. SPMCB ‘C’ characteristics, earth stud, cable support clamp suitable for 4x25 sqmm cable.Logo/Name of manufacturer shall be embosed on the pole, galvanization as per relevant IS.(c) 7.0 mtr height, 3 mm thick, bottom dia of 130mm & top dia of 70mm base plate of size 225 x 225 x 12 mm thick.

Providing and laying in position M25 grade reinforced cement concrete foundation of size 600 mm (L) ×600 mm wide and 1200 mm deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia- 1160 mm long(approx)-8 nos. and reinforcement of cold twisted bars of 8 mm dia- 1600 mm (approx) -8 nos.(with 150 mm spacing) as required with supplying and positioning of 4 nos. foundation bolts 20mm dia, 750 mm long, J type i/c 2 nos. template anchor plates of size 225mm×225mm×3mm and providing DCW HDPE for cable entry and exit as required for 7m and 8 mtr pole.

Fabrication , Supplying,Installation,testing,Commissioning of raising and lowering type 30 mts.high mast System with top diameter 150 mm (nominal size) and bottom diameter 540 mm(nominal size) as per specification and made out of not less than 4 mm thickness of material for top, 5 mm thickness of material for middle, 6 mm hickness of material for bottom including its all accessories and suitable for wind velocity as per IS 875 part 3 .There shall be in longitudinal seam weld per section and No circumfrential weld. It should also included accessories and suitable aviation obstruction light at the top of the mast For High Mast head frame ,2 point suspension system with steel wire rope 6mm dia. (7/19 construction) double drum winch ,galvanized lantern carriage arrangement suitable for 6/8 Nos. flood light luminaries symmitrically And its control gears boxes and lighting finial ,the mast shall have power motor of 2 HP motor amd manual type mounted at the base compartment of its raising and lowering operation with foundation bolts (M-30 , 12 Nos. of PCD 740 mm and length 850 mm) and Anchor plate and control panel housing suitable RCC(1:2:4) shallow foundation of size 3 m(L)x 3m wide and 3 mtr deep I/C excavation of earth , providing cutting,bending and placing in position ,reinforcement of cold twisted bars of 10 mm dia -3200 mm long(approx)-136 nos and reinforcement of cold twisted bar of 12mm dia -3000 mm(approx) -28 nos (with 150mm spacing) and 8 mm dia cold twisted bar for rings- 10 nos. of length 3200 mm as per specification reqd with positioning of foundation bolts and providing DWC HDPE pipe for cable entry or exit as required for the high mast considering the safe soil bearing capaciy at site as 10T/sqm at 2 mts .Depth with all material i/c 6/8 Nos S.P MCB ,63 A Dp Isolator etc as reqd Logo/Name of manufacturer shall be embossed on the pole. Galvanization as per relevant IS

Supply and fabrication of pole protection system made up of 8SWG steel wire mesh of size25mmx75mm rectangular with 50mmx50mmx6mm MS angle iron for supporting the mesh and grounding the protection system in suitable quality of CC etc as reqd.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

S I T C of Hot Press moulded SMC panel/Canopy Box of size(OD) 920 mmx460 mmx260 mm & (ID) 900 mmx450 mmx250 mm , anti- corrosive, dust proof , rust proof, shock proof , Self-extinguishing property , resistant to heat, Vermin proof, Ultra Violet stabilized , Pilfer resistant, Suitable for mounting 1 no 3 phase Energy meter , socket for outgoing connection with pilferage proof SMC door duly welded with S/S handle having danger logo on its outer surface and with 1 no Hot Dip galvanized iron stand for base of size 40 mm x 40 mm x 5 mm and height of the stand is 600 mm including 300 mm height below the ground with side strip of size 25 x 5 mm

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (e ) 100 amp,16ka, TPMCCB

Earthing with G.I. earth pipe 4.5 mtr long, 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or coke and salt) as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

PART C - Maintenance comprehensive maintainance of whole system for another four years (Excluding the item of Pole and allied works) afte completion of 1 year warranty 2nd year

3rd year

4th year

5th year

JINDAL INDUSTRIES