construction of building for University Line Department Coordination Centre at Panchkula

Amount

Civil work 1 to 170:- Earth work excavation in ordinary soil exclusive of compensation of earth- b. earth-work undressed with a combined lead upto 15 metres including breaking of clods (HSR 6.2 (b)

Earth work excavation in ordinary soil exclusive of compensation of earth- (HSR 6.2) c. Lead i) Extra for 15.00 meters additional lead beyond 15 metres, but upto 60 meters by manual mean (2 leads)

Dressing of earthwork :-new work or remodelling work (HSR6.3 (i))

Earth work in excavation in foundations, trenches, etc .in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches ,stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Earth filling under floors with surplus soil, excavated from foundation and taken only from outside the building plinth, in 15 cm layers, including ramming watering and consolidating lead upto 30 metres {HSR 6.13(a)}

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead upto 50 m and lift upto 1.5 m (a) Soft/loose soil.{HSR 6.25}

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chhajjas, shelves etc., inclination not exceeding 25 degree with horizontal.{HSR 9.1 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Centering and shuttering for faces of walls, partitions, retaining walls, well steining and the like (vertical or battering) including attached pilasters, buttress etc. (HSR 9.5)

Centering and shuttering for sides and soffits of beams haunching, girders bressumers and lintels .{HSR 9.7 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Centering and shuttering for staircases with sloping soffits including risers and stringers .{HSR 9.8 + Note} 1st storey

2nd storey

3rd storey

4th storey

Centering and shuttering for columns (square or rectangular or polygonal in plan) (HSR.9.9 + Note) 1st storey

2nd storey

3rd storey

4th storey

5th storey

Centering and shuttering for columns (circular orcurved in plan) (HSR.9.10 + Note) 1st storey

2nd storey

3rd storey

4th storey

Shuttering for faces of concrete foundations and foundations beams (vertical or battering) {HSR 9.13}

Extra for smooth exposed concrete finish as desired which is not to be touched or plastered but is to be left as it comes out of the shuttering for columns (square or rectangular or polygonal in plan) (45% labour rate of item No.9.9) 1st storey

2nd storey

3rd storey

4th storey

Cement concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth (HSR 10.38)

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation and plinth(HSR 10.39)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth {HSR 10.41 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in Charge in foundation and plinth (Note: Cement content considered in this item is @ 330 kg/cum). {HSR 10.66 + Note}

Providing and laying in position machine batched and machine mixed design mix M-35 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in Charge in foundation and plinth (Note: Cement content considered in this item is @ 350 kg/cum). {HSR 10.68}

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in Charge in 1st storey upto to 4 meters above plinth level. (Note: Cement content considered in this item is @ 330 kg/cum). {HSR 10.73+ Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Providing and laying in position machine batched and machine mixed design mix M-35 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in Charge in 1st storey upto to 4 meters above plinth level. (Note: Cement content considered in this item is @ 350 kg/cum). {HSR 10.75 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone aggregate with 2 coats of bitumen 20/30 penetration at 1.65 kg per sqm laid hot and sanded {HSR 10.114)

Providing and laying 80 mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 30 mm thick fine sand complete in all respects (HSR 10.159)

First class brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7+note) 1st storey

2nd storey

3rd storey

4th storey

5th storey

11.43 cm thick brick wall with every fourth course reinforced with hoop-iron laid in 1:4 cement stone dust (from crusher) mortar in superstructure {HSR 11.51 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Providing and fixing factory manufactured jali of reinforced cement concrete consisting of cement, coarse sand and 10 mm and down gauge bajri in the ratio of 1:1:2 with 8 mm dia for steel. Outer frame of the jali will be 50 mm wide and 25 mm thick and inner frame of jali will be 25 mm wide and 25 mm thick with smooth finish as per the design approved by the Engineer in Charge including fixing in position up to any height with cement sand mortar 1:4, complete in all respect.{HSR 11.103}

Top khurra 0.6 m X 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50}

Bottom khurra on ground 1.2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57)

Cement concrete 1:2:4 gola 10 cm X 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified (HSR 13.64)

Providing and fixing PVC rain water pipe pressure of ISI mark in cement mortar during masonry work {HSR 13.89(a)} (a) 100 mm dia PVC pipe 6 kg. pressure

Providing and fixing PVC bend ISI mark (a) 100 mm dia PVC bend {HSR 13.90(a)}

Providing and fixing false ceiling with 12 mm thick Gypsum Board fixed on M.S. steel runners frame including cost of screws angles, cleats, rawel plugs with taping, filling with Gypsum compound and applying priming coat etc. complete in all respects{HSR 13.91}

Providing and fixing mineral fibre false ceilings tiles at all hieghts of size 595 x 595 mm of approved texture, design and pattern, the tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 85%, Thermal Conductivity K = 0.052 (-) 0.057 w/m k, Fire Performance as per (BS 476 pt - 6 & 7) in true horizontal level suspended on interlocking T-Grid of hot dipped all round gavanized iron section of 0.33 mm thick (galvanized @ 120 gsm) comprising of main T runners of 15 x 35 mm of length 3000 mm, cross T of size 600 x 600 mm suspended from celing using galvazied mild steel item (galvanizedd @ 80 gsm) 50 mm long 8 mm outerdiameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm, spaced at 1200 mm centre of centre along main 'T'. The suystem should rest on periphery walls/partitions with the heop of GI perimeter wall angle of wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all hieghts, The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-charge. with or without groves (HSR 13.92)

Terracing consisting of 19 mm thick heat resistant tiles for roof insulation, 300 mm x 300 mm laid on 20 mm thick 1:3 cement coarse sand mortar including grouting with neat white cement over average 75 mm thick screed of 1:8:16 including two coats of bitumen laid hot at 1.65 kg per sqm on top of RCC slab and cleaning of top surface, complete. The tiles shall be made of white cement blended with fibrous polymer having flextural stress value of ≥150 kg/ cm² & thermal conductivity value ≥0.18 w/m.k. (HSR 13.97)

Providing and fixing GI clip in Metal Ceiling System of 600 x600 mm module which includes providing and fixing 'C' wall angle of size 20 x 30 x 20 mm made of 0.5 mm thick pr painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10 x 38 x 10 mm made of GI steel 0.7 mm thick from the soffit with the help of soffit cleat 7 x 27 x 25 x 1.6 mm, rawl plugs of size 38 x 12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with: b) CI metal Ceiling clip in plain Beveled edge global white colour tiles of size 600 x 600 and 0.5 mm thick with 25 mm height, made of GI sheet having galvanized of 100 gms/sqm (both sides inclusive) and 20% perrforation area with 1.8 mm dia holes and having NRC of 0.5 electro statically polyester powder coated of thickness 60 microns (minimum) including factory painting after bending and perforation. (HSR 13.100)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling (HSR 14.1)

Screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping (HSR 14.4 + Note) 2nd storey

3rd storey

4th storey

5th storey

Kotah stone flooring, minimum 25 mm thick, in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.(HSR 14.62) (Note : The flooring shall be finished with granite polish and nothing shall be paid extra). 1st storey

Kotah stone 20 mm thick in skirting risers of steps, dados pillars and wall facing(lining) in any pattern as specified 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. (HSR 14.66) (Note : The skirting shall be finished with granite polish and nothing shall be paid extra). 1st storey

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in flooring laid in any patterns as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.89} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.90} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this. {HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92} (b) size of ceramic glazed tiles 300 mm x 450 mm

12 mm thick cement plaster 1:6 on walls {HSR 15.7 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

Providing edge moulding to 17-20 mm thick granite stone counters, Vanities etc., including machine polished to edge to give high gloss finish etc. complete as per design approved by Engineer in Charge. (Moulding) (HSR 14.98) (a) Single moulding

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10+ Note) 1st storey

2nd storey

3rd storey

4th storey

5th storey

18 mm cement plaster in 2 coats under layer 12 mm thick cement plaster 1:5 (1 cement, 5 coarse sand) and top layer 6 mm thick with cement mortar 1:3 (1cement, 3 coarse sand) finished rough with sponge. {HSR 15.20 + Note} 1st storey

2nd storey

3rd storey

4th storey

5th storey

10 mm thick plaster 1:3 under ceiling (HSR 15.52 + Note) 1st storey

2nd storey

3rd storey

4th storey

5th storey

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead , linseed oil, varnish and chalk mitti including finishing the surface to required finish complete {HSR 16.1}

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc.{HSR 16.2}

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade {HSR 16.3}

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces {HSR 16.25}

Distempering with washable oil bound distemper (of approved manufacture) two coasts excluding priming coat on new work{HSR 16.57}

Providing two coats of exterior acrylic emulsion paint {HSR 16.79} b) 1st quality

Providing and applying two coats of white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete (J.K/ Birla make). (HSR 16.81)

Wire gauze commercial hard wood such as hollock , champ, chikrassy , etc., ( Non –coniferous timber other than teak conforming to I.S. specification no. 1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position ( excluding the cost of tower bolt and handles but including the labour for fixing the same)- {HSR 17.31 (i)} (i)30 mm thick Note: Nothing shall be paid extra for additional vertical style (any size) if required by the Architect or by the Engineer-in-Charge)

Providing and fixing six-leavers brass 10 cm mortice latch and lock, and a pair of lever handles with necessary screws, etc. complete in all respect. (HSR 17.73)

Providing and fixing six leaver brass 10 cm mortice latch, with one dead bolt and a pair of leaver handles with necessary screws etc. complete (Indian make of reputed firm. such as Godrej or equivalent) (HSR 17.74)

Providing and fixing 150 mm floor brass door stoppers, with rubber cushion, screws, etc., to suit shutter thickness complete (HSR 17.75)

Supplying and fixing hydraulic door closer, I.S.I. mark, with necessary screws , etc., complete- (HSR 17.82(b )} (c) I.S.I. designation No. III ( size of door 701 mm to 850 mm)

Providing and fixing 65 mm x 35 mm special quality brass cup-board locks, six levers, of reputted farms such as Godrej or equivalent, including necessary screws, etc. complete (HSR 17.85) a) Brass

Providing and fixing 30 cm long aluminium finger plate, 65 mm x 1.6 mm, including necessary screws, etc. complete (HSR 17.86)

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (HSR 17.93(a)} (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :- (i) 25 mm thick

(iii) 35 mm thick

Providing and fixing Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS;733 and IS; 1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth rust free straight mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, all complete. (HSR 17.95) Fixed portion (Anodized Aluminium transparent or dyed to required shade according to IS;1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS; 733 and IS;1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including clear angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, etc. complete. (HSR 17.96) Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including of cost of PVC/ neoprene gasket required including Aluminium fitting.

Providing and fixing 12 mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to IS;12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with CP brass/ stainless steel screws etc. complete. (HSR 17.97(b)} (b) Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, windows, ventilator shutter and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). {HSR 17.98(b)} (b) With float glass panes of 5.00 mm thickness.

Providing Aluminium Jali of thickness 7 mm thick with openings – 75 mm x 75 mm of including anodizing and fixing in frame with cost of screws etc. complete. (HSR 17.100)

Providing and fixing of casement and fixed windows made from multi chambered UPVC profiles of 56 to 68 mm width in natural from stablized for heat, light, impact & UV radiation. The UPVC profiles should be reinforced with galvanized steel profiles of designed thickness. All openalble sashes shall be having weather seal fitted in continuous lengths made from Bubble EPDM Rubber and side hung/top hung with upto 90 degree opening friction stays of SS 304 with provision of multipoint locking system made from Espag rods. All handle shall be made from Die Cast Zinc alloy (Model ESPAG) BS-1004A in white finish with suitable locking arrangement. The windows shall be fixed to opening using expandable screws and friction stays that shall be able to with stand wind speeds upto 180 km/hr. the shoot bolts in windows shall be rust proof metallic coated steel. The window frames shall be fixed in masonary wall RCC with necessary fasteners, nuts, bolts, washers, caps, silicon sealant etc. complete (HSR 17.103) (c) Double glass glazing comprising of 6 mm thick toughened clear glass + 12 mm air gap+ 6 mm annealed cleaar glass.

Providing and fixing double glazing consisting of 6 mm (toughened) and 6 mm annealed plain glass including 12 mm air gap including cost of structural silicon sealant & weather sealant (DC 795/DC789) and double sided acrylic foam tape in structural glazing works upto four storey. The outer glass shall have U value ≤ 1:8, solar factor and ≤0.35 Light transmission ≥ 49% (HSR 17.104)

Wrought iron and mild steel (using angles, flats square bars. tees and channels) ladders, grills, gratting frames, window guards, iron door openable or fixed stair case or parapet or any other type of railing , gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC incluidng straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position, complete in all respect for all heights/depths/storeys/basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separtely for different diameters as actually used in work excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Supplying openable steel doors and windows, of standard steel sections, joints mitred and electrically flash welded including provision for arrangement of receiving handles, peg stay, catcher will also be welded with the frame and providing and fixing pressed steel projected hinges, iron lugs, glazing clips (excluding wooden shutters, glazing and fittings such as handles, peg stay and catcher etc.) and finished with one coat of ready mixed red lead non setting primer (HSR 18.24)

Pressed steel sheet frames (chowkhats), consisting of 2.00 mm thick steel sheet of the specified section, including iron lugs (hold fasts, iron hinges, confirming to PWD specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red led non-setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs, complete:- (HSR 18.34 (a)} a. door and window frame of size 89mmx 50mm with 40mm wide single rebate

M.S. Angle iron nozing of specified section including cutting to size, welding of M.S. bars for embedding in flooring and steps etc., fixed in position. (HSR 18.39)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm (NS)

Providing and fixing 25 mm dia stainless steel curtain rods weighing 0.560 kg/meter with brackets & side covers (balls) of vista make, clamps, plastic gutties/rawl plugs etc., complete in all respects. (NS)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).(NS)

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.(NS)

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 15-18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.(NS)

Providing and fixing 15-18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:3 (1 cement : 3 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of cat eye colour and shade Area of slab upto 0.50 sqm

Extra for pre finished nosing to treads of steps of marble/granite stone with approved adhesive, complete in all respect

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 15-18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a) Polished finish Granite stone slab Cat Eye

b) Polished finish Granite stone slab Cherry Red

c) Polished finish Granite stone slab Elite Brown

Providing and fixing Polished Granite stone slab 15 to 18 mm thick in risers of steps, skirting, dado and pillors laid on 12 mm (average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a)Polished Granite stone slab Cat Eye

b) Polished finish Granite stone slab Cherry Red

c) Polished finish Granite stone slab Elite Brown

Providing and fixing of ‘Unistone’ or equivalent Glass Reinforced Concrete (G.R.C) Wall Cladding Tiles in approved design, size, texture, thickness, pattern and color. The thickness of the tiles should range between 12 to 18 mm (depending on the texture of the tile), allowing variance of ± 2 mm in accordance with IS: 1237‐1980. The composition of tiles should be ‘43’ Grade Portland cement, reinforced with Alkali Resistant Glass Fiber and homogeny pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX / Lanxess (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and concrete mix design compressive strength equivalent to M‐40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on 12 mm thick rough plaster of 1:3 cement mortar 1:3 (1 cement: 3 coarse sand) and the fixing of tiles should be done by ‘Unistone’ tile adhesive or equivalent as per manufacturer’s laying instruction. (NS)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).(NS)

Providing and fixing trap door in the false ceiling using 19 mm thick commercial block board laminated with approved finish 1 mm thick laminate with necessary teak frame work of size 50 mm x 40 mm, teak wood mouldings as per Architect's drawing, brass hinges, latches etc. complete in all respect as directed by the Engineer in charge (NS)

Providing and fixing 12mm thick toughened glass of AIS/Modi Guard/Saint Gobain make duly toughened by standardized plant for making the door and cabins/partitions of different size with required holes and cut outs in fixed partition & openable panels/leaf for fully glazed single/double leaf doors including fixing of glass in partitions by using 3mm to 6mm wide silicon adhesive, complete in all respects as per architectural drawing and design or instructions of Engineer-in-Charge. (NS)

Providing and fixing fittings/accessories of DORMA make as given below. {NS} (i) Wall Connecting Profile (WCP) suitable for 12 mm thick glass DORMA XL-C-4026-A-12mmS

(ii) Connector for overpanel and sidelight DORMA XLC-4004 A

(iii) Patch fitting for overpanel and sidelight DORMA XL-C 4003A

(iv) Pull handle D type (pair) of size 300x22mm DORMA XLC-3002 A

(v) Glass door package with lock DORMA XL-C 4001 B

Providing and fixing aluminium tubular handle bar 32 mm outer dia 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer in Charge Powder coated minimum thickness 50 micron aluminium tubular handle bar (NS)

Providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing & polishing of cut edges etc. complete (NS)

Providing, diluting and injecting chemical emulsion for pre-constructional anti-termite treatment and creating a continous chemical barrier under and all round the column pits, wall trenches, basement excavation, top surface of plinth filling junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surronding of pipes and conduits etc., complete as per PWD specifications (plinth area of the building at ground floor only shall be measured of payment (NS) ( the material i.e. Chlorphriphos Emulsifiable concentrate 20% with 1% conentration shall be arranged by the contractor)(NS)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.(NS)

Providing and mixing integral crystalline admixture for waterproofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc.. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R- 2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.(NS)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. a) For vertical surface two coats @ 0.70 kg per sqm(NS)

b) For horizontal surface one coat @1.10 kg per sqm.(NS)

Designing, providing and fixing 4mm thick Aluminium Composite Panel (ACP) cladding at all height of ALUCOBOND, DIBOND,ALUCORE over Brick/RCC surface either segmental / straight in plan wherever specified with extruded aluminium U section of size 25 mm x 19 mm x 2 mm, aluminium angle cleats of required size, weather sealants, backer rods of required size, stainless steel screws, rivets, brackets, drilling and fixing the cladding to either masonry or reinforced cement concrete as the case may be as per manufacturer's specifications, complete the work in all respects including all necessary accessories. At all soffits Aluminium Cladding shall be bend at 90 degree and joints at corner or edges will not be acceptable. On horizontal surface, the size of sheet should be maximum available of size, complete in all respect as per architectural drawing and design. (NS)

Providing & fixing open cell ceiling This includes Uni T grid Wall angle of 19mmx19mm shall be screw fixed to brick wall/partition with the help of approved screws at 600mm centers. Then suspending Uni T Main T grid of 15mm x 38mm of length 3600mm is hung with adjustable level clips 80x30x0.7mm & 4mm diameter GI rod which are connected to Soffit Cleat 27x35x1.5mm and Approved 50mm dash Fasteners @1200mm centers or as approved from RCC Slab. The Cross T of 15mm x 38mm of 1200mm length shall be interlocked between main T Grid at 600mm centers to form 1200 x 600mm modules. 600 x 600mm modules to be formed by click fitting Cross T of 15mm x 38mm of 600mm length centrally between the 1200mm cross T’s. Then Open cell ceiling panels are formed with mounting end and edge rails to get Cell Sizes of (75x75mm)/ (100mm x 100mm) / (150X150mm) / (200X200mm) , which shall be placed into the above grid of size 600x600mm. The Web Height of the open cell shall be of 50 mm. Mounting and edge rail are made out of are 0.5mm thick Pre coated GI with 25 to 30 Micron polyester paint thickness. Brand USG Boral (NS)

Providing & fixing High Pressure Laminated (HPL) sheet for Internal Wall Cladding / Panelling at all height wall punched of "Shaurya-Wall Punched" made from 6mm High Pressure Laminated (HPL) compact laminates which are manufactured from sheets of special Kraft papers and decor paper with thermosetting resin, fused together under high pressure and temperature as per IS 2046 and EN 438. Which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. NOTE: It is a natural occurrence under the various climatic condition that HPL compact board may undergo dimensional changes within the range ±3 mm. Profiles used:-Cover profile A4: Aluminum , Aluminum Corner Profile-Anodized. The cover profile A4 offers a smooth shape to the structure. Corner profile is affixed with a compact on corner to provide corner protection ect. complete in all respect as per architectural drawing and design (Make: Merino, Windermax, Frontage).(NS)

Providing and fixing 5mm thick toughened glass at all height of AIS/Modi Guard/Saint Gobain make duly toughened by standardized plant for railing in required shape and size as per drawing including making holes and cut outs for fixing in railing with SS 304 grade (excluding cost of stainless steel railing) screws, clamps etc. all hardware fittings complete in all respect as directed by Engineer in Charge.(NS)

PH work 171-321:- Excavation of trenches in streets, lanes or in open areas for storm sewer, sewers running by gravity and manholes to full depths as shown in drawing including shoring, timbering of poling boards, frame system type, dressing to correct sections and dimension, according to templates and levels, dewatering, provision for diversion of traffic, cutting trees and bushes, etc., night signals, profiles, pegs, sight rails, boning rods, crossing over trenches, for access to the houses, watching, fencing, etc., fixing and maintenance of caution boards, refilling of trenches, watering of refill, in 15 cm layers, ramming and restoration of unmetalled or unpaved surface to original condition and removal of surplus soil, from site of work, up to a lead of 1 K.M. in ordinary soil {HSR 6.10(a)} (a) for depth of excavation not exceeding 3 metres below ground level

Cement concrete 1:5:10 with brick ballast 40 mm nominal size in foundation and plinth. {HSR 10.34}

Providing and fixing CAST IRON DOUBLE FLANGED SLUICE VALVES PN-1.6 MARKED WITH IS: 14846 including nuts & bolts marked with IS:1363, rubber sheet Is: 638 etc. carriage, loading unloading, stacking handling, we-handing etc. complete in all respect to the satisfaction of the engineer in charge ( makes- AARKO, VENUS LEADER SI. PANJA, UPADHAY). (HSR 28.10) (Amended) (a) 100 mm i/dia of valve

(b) 150 mm i/dia of valve

(c) 200 mm i/dia of valve

Providing, lowering, laying, cutting (cut surface to be uniformly finished), jointing with rubber rings marked with IS:5382 and testing of spigot and socketed RCC NP-2 marked with IS:458-1998 and specials into trenches for all depths including carriage, loading, unloading, stacking, handling, rehandling etc. complete in all respect to the satisfaction of the Engineer-in-Charge. (HSR 28.60) (i) 200 mm i/d

(ii) 250 mm i/dia

Providing and fixing steel bar embedded plastic steps of size 263 mm x 165 mm of orange colour, conforming to specifications, in pump chambers, manholes etc., having minimum 3 mm thick polypropylene on 12 mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1:2:4 cement concrete including carriage, loading, unloading, stacking, handling, re-handling etc., complete in all respects to the satisfaction of Engineer-in-Charge. (HSR 29.28)

Providing and fixing 25 mm thick marble partitions for different type of urinals. (HSR 30.40) (II) LARGE SIZE 835 mm x 355 mm (a) white

Providing and fixing 40 mm i/dia chromium plated brass trap with chormium plated brass pipe to wall with wall flange, complete (as per requirement of the Engineer-in-charge) for use with sinks. (HSR 30.63 (a) (a) With Bottle Trap (Indian make)

Providing and fixing in position best Indian make shower with 15 or 20 I/d out let. (HSR 30.66) (c) C.P. brass with revolving joint

Providing and fixing in position best Indian make paper holder fixed into wall with C.P. brass screws complete in all respect including cutting and making goods with wall etc. (HSR 30.67 (a) (a) C.P. Brass

Providing and fixing in position best Indian make towel rails fixed in with rawlslugs embedded in walls with C.P brass screws. Complete in all respects including cutting and making good the walls etc.(HSR 30.68 (d) (d) C.P brass two swivel towel rail 400mm long

Providing and fixing in position best Indian make soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the walls etc. {HSR 30.70(a)(i)} (a) C.P. BRASS (i) soap dish large

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P brass screws and rawl plugs etc. complete including cutting and making good the walls etc. {HSR 30.73(a)(ii)} (a) C.P. BRASS (ii) two way

Providing and fixing in position C.P brass stop cock (as approved by the Engineer-in-charge) {HSR 30.76(a)(ii)} (a) 15 MM STOP COCK (ii) concealed stop cock with flange

Providing and fixing C.P brass liquid soap container of best quality (as required by the Engineer-in-charge). {HSR 30.77}

Providing and fixing in position best Indian make C.P brass inlet connection 15mm with 375mm pipe and C.P brass nuts. (HSR 30.83)

Providing and fixing in position automatic brass ball valves in tanks {HSR 30.110(a)(iv)} (a) WITH COPPER BALL (iv) 32 mm internal diameter

(v) 40 mm internal diameter

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150 mm X 150 mm cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm X 300 mm and outside size 330 mm X 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundations, and cement concrete 1:2:4 in coping around C.I. cover and frame et. With three coats of black bitumastic superior paint of approved manufacture on all C.I. work as per standard design, minimum depth of water should be 150 mm with a minimum seal 50 mm {HSR 30.114(b)} (b) 100 mm internal diameter H.C.I. gully trap

Providing and fixing HDPE WATER STORGE TANKS of sintex, diplas O.K. Supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. {HSR 30.119) 500 ltrs, capacity

Supply and erection of PVC copper insulated and sheathed 2 core circular flexible wire {HSR 31.9 (i) (d)} (d) Size 1.50 sqmm (48/0.20 mm)

Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switched etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide. (HSR 31.13 (ii) (ii) Size 40mm x 40mm x 6mm

Supply and erection of underground cable, loose in existing pipe or trences complete with necessary connection:- (HSR 31.26) (i) 4 core 10 sqmm

(ii) 4 core 16 sqmm

(iii) 4 core 25 sqmm

(iv) 3.5 core 35 sqmm

Earthing. (HSR 31.22[xv]) (xv) Providing and fixing 25 mm x 5mm G.I. strip on surface or in recess for connections etc. as required with all labour and material.

Supply and erection of suitable compression type brass cable glands for underground Cable:- (HSR 31.28) (i) Upto 6 sqmm cable 2 to 4 core

(ii) 10 to 16 sqmm cable 2 to 4 core

(iii) 25 to 50 sqmm cable 2 to 4 core

Providing and fixing in position quality stainless steel sink built in draining board of size 600mm X 450 mm complete in all respect as per AISI 304/18/8 of best quality. (NS) a) 600mm X 450mm X 200mm

Providing and fixing in position white vitreous china wall mounting water closet, soft close seat cover, concealed cistern with dual flush plate, of flushing capacity 2 litre/4 litre, including seat cover, and cistern fittings, nuts, bolts and gasket etc complete in all respect. (NS) Make : JAQUAR/PARRYWARE/KOHLAR.

Providing and fixing white vitreous china wash basin with fabricated MS brackets painted white synthetic enamel paint over a coat of primer of approved brand, all of approved brand and manufacturer to wall with C.P. wall flange and rubber adopter for waste connection complete, including cutting and making good the walls & Floors wherever required. a) Oval Type (NS) Make : JAQUAR/PARRYWARE/KOHLAR

Providing & fixing low flow C.P. brass single hole basin Mixer Tap with aerator of approved make complete in all respect as directed by Engineer-incharge. (Make Jaquar, Modal No:- ALD-CHR-233, OPP-CHR-15233KPM) OR Equivalent Kohlar & Essel (NS)

Providing & fixing low flow C.P. brass pressmatic pillar tap of approved make complete in all respect as directed by Engineer-incharge. (for public Toilet) (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing, Fixing satin finish stainless steel AISI 316 grade wall mounted twin coat hook on door complete in all respect as directed by Engineer-in-charge. (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing, fixing, testing and commissioning Hand Shower (Health Faucet) with 8mm Dia,1 Metre Long Flexible Tube & Wall Hook of approved make and manufacture complete as per direction of Engineer in Charge.(NS) Make : JAQUAR ALD-573/KOHLAR/ESSEL

Providing and Fixing 2 No. hand rail size 600X100mm and grab bar 450mm long to mounted on the track (vertically and laterally) for handicaped toilet complete in all respects as directed by Engineer-in-charge. (NS) Make : JAQUAR AHS-1503/KOHLAR/ESSEL

Providing and fixing low flow type two way bib tap and flow restrictor 6 LPM at 3 Bar Pressure as per approved make complete in all respect as per engineer in the charge. (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing, testing & commissioning of C.P. brass shower assembly comprising of Exposed Shower Pipe with Provision For Simultaneous Working Of Showers with Operating Divertor Knob, Flat Shape 071X50X15mm & 350mm Wide with Sliding Holder For Hand Shower, Wall Bracket & 8mm dia, 0.5M Long Flexible Tube (for Connection to Exposed Shower Mixer) Without Shower. (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing & fixing low flow C.P. brass Bib tap of approved make complete in all respect as directed by Engineer- incharge. (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP and one layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 20 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. i) DN 40 mm o/d PP mineral filled SWR pipe (NS) Make : REHAU/POLOPLAST/WAVIN

(ii) DN 50 mm o/d PP mineral filled SWR pipe

(iii) DN 75 mm o/d PP mineral filled SWR pipe

(iv) DN 110 mm o/d PP mineral filled SWR pipe

Providing and fixing Brass Floor Clean Out plug with suitable insert keys for opening to soil pipe / waste pipe of uPVC pipe as required complete as per drawing, approved sample and direction by Engineer-in-charge: (NS) Make : REHAU/POLOPLAST/WAVIN

Providing & Fixing Low Noise Floor trap with minimum 50mm water seal with 110mm Top inlet and 1nos of DN 110mm outlet, Height riser minimum 150mm height and above connection to basin, shower area in P-Trap to complete the work as per satisfaction of engineer in the charge.110 x110 mm outlet (NS) Make : REHAU/POLOPLAST/WAVIN

Providing and fixing floor drain of 110X50 size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects. (NS) Make : REHAU/POLOPLAST/WAVIN

Providing and fixing 125mm chromium plated grating with ring and S.S anti cockroach basket and two S.S screws of approved design with grating screwed down to the ring with s/s screws and embedding and setting ring into the floor with cement mortar .(As per approved make or equivalent) (NS) Make : JAQUAR/KOHLAR/ESSEL

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall and terrace a) 15 mm dia (NS) Make : AKG/SUPREME/PRINCE

(b)20mm dia

(c)25mm dia

(d) 32mm dia

Providing, Fixing, Testing & Commissioning of nitrile rubber insulation on hot water supply pipes. of approved make complete in all respect as directed by Engineer-in-charge.(NS) Make : INDIGO/RAJCO/LAWTON a) 15mm dia (13 mm thickness)

(b) 20mm dia (13 mm thickness)

(c)25mm dia (13 mm thickness)

(d) 32mm dia (13 mm thickness)

Providing and fixing gunmetal wheel valve of approved quality (Screwed end) a) 15mm dia nominal bore (NS) Make : NVR/ZOLOTO/KARTAR

(b) 20mm dia nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) withh R.C.C. top slab withh 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick withh cement mortar 1:3 (1 cement : 3 coarse sand) finished withh floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished withh a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover withh frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With Sewer bricks conforming to IS : 4885 (NS)

Extra for depth for manholes : (DSR 19.8) Size 90x80 cm With Sewer bricks conforming to IS : 4885 (NS)

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 ( 1 cement : 4 Coarse sand ), in side cement plaster 12 mm thick withh cement mortar 1:3 ( 1 cement : 3 coarse sand) finished withh a floating coat of neat cement, foundation concrete 1:3:6 mix ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 ( 1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished withh a floating coat of neat cement all complete as per stander design. (DSR 19.9) 0.91 m deep withh S.F.R.C . cover and frame ( heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 Kg. fixed in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation , foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) With Sewer bricks conforming to IS : 4885 (NS)

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m With Sewer bricks conforming to IS : 4885 (NS)

1620 lpm at 55 m Head ( Electric Pump):- Supply, installation, testing and commissioning of Horizontal type, single stage centrifugal, split casing pump with bronze impeller Stainless steel shaft factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP‐ 55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles AC. Capacity 1620 LPM at 5.5 Kg/cm2 delivery pressure for Fire Hydrant Network.(NS) Make: LUBI/XYLEM/EBARA

1620 lpm at 55 m Head (Diesel Pump) Supply, installation, testing and commissioning of Horizontal single stage centrifugal pumping set with CI volute and bronze impeller with mechanical seals directly coupled to automatic Diesel Engine complete with all accessories like self starting by means of Battery powered electric starter motor, Paper Filter type air cleaner, exhaust silencer etc. complete in all respects. The engine & the pump will be mounted on common base plate on anti‐vibration mountings.150 mm diameter M.S. Class 'C' diesel pump exhaust pipe includings all fittings, like bends, tees etc. clamps / structural steel supports. The pipe shall be provided with 75mm thick fiberglass insulation & covering the insulation with 500 g polythene sheet giving proper overlaps & sealing the joints with suitable adhesive compound. The pipe shall be provided with 24 gauge aluminium sheet cladding. Capacity 1620 LPM at 5.5 Kg/cm2 delivery pressure for Fire Hydrant. (NS) Make: LUBI/XYLEM/EBARA

180 lpm at 55 m Head ( Jockey Pump) Supply, installation, testing and commissioning of Horizontal type, single stage centrifugal, split casing pump with bronze impeller Stainless steel shaft factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP‐ 55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles AC. Capacity 180 LPM at 5.5 Kg/cm2 delivery pressure for Fire Hydrant Network. (NS) Make: LUBI/XYLEM/EBARA

CONTROL PANEL Supplying, installation, testing and commissioning of cubicle type free floor / wall mounted front operated panels sheet metal enclosed dust and vermin proof confirming to IP-42, compartmentalized design Form-3B made out of 2.0 mm powder coated sheet steel for load bearing structure and 1.6 mm for non- load bearing structure, and Side Partition & MS angle iron framework, powder coated finish with two coats of red oxide primer, including internal wiring with PVC insulated FRLS conductor , 1100 volts grade in a ccordance with Technic al Specific ations & , 25 x 3 Sq.mm aluminium earth tape from end to end of the panel, provision of c able entry from top / bottom both option, consisting of the following, (G.A. drawing of panel to be approved before fabric ation) Make: Adlec / Tricolite / Ambit / SPC / Neptune NOTE-a) All motor starters shall be provided with auxiliary conta ct for Integration with Fire Alarm Panel/BMS. b) Potential free conta cts shall be provided for automatic control of pumps and for Inte gration with Fire Alarm Panel/BMS. c) All a ccessories and internal control wiring shall be done in all respect. d) Motor Duty MCCB shall be provided for Incoming and Outgoing ( Motor e) All control wiring shall be of 2.5 mm² and CT wiring shall be of 2.5 mm². (a) Incoming 1 No. 250 Amps, FP Motor Duty MCCB (35 KA) (b) Metering & Instruments (i) 1 Set 96 mm x 96 mm Digital Voltmeter (0-500V) with suitable rating CTs. (ii) 1 Set 96 mm x 96 mm Digital Ammeter (0-630A) with suitable rating CTs. (c) Busbars, 1 Set of 300 Amps, 415 Volts, 50 Hz, 3 phase, 4 wire colour coded Al. bus bars. (d) Outgoing: (i) 1 Nos. 125A TPN Motor duty MCCB, 415V, 35 KA with Rotary operating (ii) 02 Nos. DOL starter suitable for 15 HP, Type-2 Co-ordination (as per IS/IEC (e) 1 No. 200A TPN MCCB Outgoing Spare Feeders (f) 1 No. 32A TP MPCB Outgoing Spare Feeders (g) 2 Nos. 63A TP MCCB ( For 1 No. Terra ce Booster pumps motors and 1 No. Sp are) (h) Providing and fixing 1 No. Auto Start Panel a ctivated with pressure switch for Diesel Engine complete with all a ccessories, batteries, battery charger of suitable rating, DC Ammeter, Voltmeter, MCB timers, push buttons, 8 window fault annunciator, wiring and control c abling including connection to diesel engine com plete as required read y for working. (NS)

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (NS) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation 900LPM @35M HEAD Make: LUBI/XYLEM/EBARA

Providing & fixing heavy duty double flanged Flexicon rubber expansion joint (suitable for system test pressure) of standard length as per manufa cturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required. (NS) (a) 80 mm dia

(b) 100 mm dia

(c )150 mm dia

(d) 200 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : (NS) Make: EPAGO/SAFEGUARD/MINIMEX Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : (NS) Make: SPAGO/SAFEGUARD/MINIMEX Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia Stainless Steel short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : (NS) Make: SPAGO/SAFEGUARD/MINIMEX Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.(NS) Make: SPAGO/SAFEGUARD/MINIMEX 30m

Providing & fixing angle iron (40mm x 40mm x 5mm ) door frame and MS sheet (2mm thick) cum glass shutter of size 2.1 mtr x 1.2 mtr (N.S) with 25mm x 25mm x 3 mm angle frame all around & stiffened in between i/c hinges, handle, locking arrangement, painting with approved synthetic enamel paint i/c sign writing on glass at internal hydrant including providing & Fixing MS sheet 2mm thick on remaining portion above door to close opening i/c painting etc as required. (NS) Make: SPAGO/SAFEGUARD/MINIMEX

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : (NS) Make: SPAGO/SAFEGUARD/MINIMEX 2 way-100 mm dia M.S. Pipe

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(NS) Make: TATA/JINDAL/PARKASH (SURYA) (a) 200NB dia

(b) 150NB dia

(c )100NB dia

(d)80NB dia

(e)25NB dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.(NS) Make: TATA/JINDAL/PARKASH (SURYA) 150NB

Supplying, fixing, testing & commissioning of Butterfly Valves of rating PN 1.6 with mating flanges ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : (NS) Make: SPAGO/SAFEGUARD/GURU (a)150 nominal bore

(b)100 nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : (NS) Make: NVR/ZOLOTO/KARTAR (a) 150NB dia

(b)100NB dia

Providing and fixing in position the industrial type pressure gauges with gun metal /brass valves complete as required (NS) Make: SPAGO/SAFEGUARD/MINIMEX

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard (NS) Make: SPAGO/SAFEGUARD/MINIMEX conforming to IS 926.

Supplying and fixing ofAir release valve as per IS:14845 ISI Marked (NS) Make: SPAGO/SAFEGUARD/MINIMEX

Providing, installation, testing and commissioning of Cast iron double flange strainer with stainless steel mesh, PN 1.6 rating complete with accessories as required.(NS) Make: SPAGO/SAFEGUARD/MINIMEX (a) 200 NB

Providing and fixing of CO2 4.5 kg High Pressure Portable Fire Extinguisher, filled with Co2 Gas as per IS 15222, Control discharge mechanism fitted with 1 Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2,Applicable on Class B, C and electrically started Fire, Fire Rating 21B, External coating is of enamel spray painting, Valve Confirm to IS 3224 ISI Marked, CO2 Cylinder construction : hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 15683:2006 and ISI marked.(NS) Make: SPAGO/SAFEGUARD/MINIMEX 4.5kg capacity cylinder

SITC of carbon-di-oxide 9 Kgs capacity fire extinguisher, made of mild steel with chromium plated gun metal union (cap), fitted with braided hose The extinguisher is internally coated with Lead Tin by electrolitic Process and externally coated with lead tin with Fire red Paint and cylinder bearing with ISI 15683. Incuding the cost of all petty material required to complete the job upto entire satifsfatction of Engineer-in- charge. (CO2 MOBILE EXTINGUISHER WITH 55B FIRE RATING) 9 kg capacity cylinde (NS) Make: SPAGO/SAFEGUARD/MINIMEX

Providing and fixing of Dry Chemical Powder (UL Listed MAP-50% ABC) 6 Kg, Stored Pressure Type, UGTS Pressure Gauge, Controllable discharge mechanism, Jet Range 5 Meters, applicable on Class A,B & C and electrically started Fire, A Rating- 3A, B Rating 21B, Can Construction : Deep drawn & CO2 Mig welded, CE Marked Valve with inbuilt NRV & Safety Release Provision, EPDM Rubber Hose with both end Aluminum clamped, External Coating - Pure Polyester Powder coating (UV Resistant), Brass forged valves with safety Pin is of SS material, Helium Leak Detection Tested, ISI Approved IS 15683:2006 and CE Certified.(NS) Make: SPAGO/SAFEGUARD/MINIMEX Dry Chemical Powder ABC type of 6 Kg

SITC of CLEAN AGENT TYPE fire extinguishers, 4.0 kg capacity conforming to IS:15683 with extinguishing agent: FE 36 (HFC-236fa) and enviromentally save with ZERO ODP, wall bracket handle fitted with high pressure flexible discharge hose with ISI certitifcation mark.Incuding the cost of all petty material required to complete the job upto entire satifsfatction of Engineer-in-charge. 4 kg Capacity cylinder (NS) Make: SPAGO/SAFEGUARD/MINIMEX

Supplying, installation, testing & commissioning of repeater panel wih 320.Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. character/ (NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounde complete as required. (NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Supplying, installation, testing & commissioning of addressable manual call point complete as required. (NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Supplying, installation, testing & commissioning of fault isolator complete with base as required.(NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Supplying, installation, testing & commissioning of addressable fire control module complete as required. (NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.(NS) Make: Polycab/Paramount/Proshield/CMI 2 x 1.5 sq. mm

Supplying, installation, testing & commissioning of addressable Multicriteria Detector complete as required.(NS) Make: Ansul/Edwards/Notifier/Wissenchaflter/Rux

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes,hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.(NS) (a) Thickness 0.63 mm sheet

(b) Thickness 0.80 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.(NS) (a) Thickness 0.63 mm sheet

(b) Thickness 0.80 mm sheet

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications. (NS)

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications. (NS) Make: Balance/Trox/Caryaire

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required. (NS) Make: Balance/Trox/Caryaire

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. (NS) Make: Balance/Trox/Caryaire

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core. (NS) Make: Balance/Trox/Caryaire

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. (NS) Make: Balance/Trox/Caryaire (a) Fire damper

(b) Actuator

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. (NS) Make: UP Twiga/Oweans Corning/Styrene

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.(NS) Make: Kflex/Armacell/Surpreme (a) 19mm

Supplying and fixing 50 mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/ cu m after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications) (NS) Make: Kflex/Armacell/Surpreme

Laying and fixing of one number PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1.1kv grade of size not exceeding 25 sq.mm on surface as required. (NS) Make : RR/Polycab/AKG (a) Upto 35 sq. mm (clamped with 1mm thick saddle)

(b)Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

(b) First Floor: VRV ODU with multiple modules in each ckt : 20 HP

(c)Second Floor: VRV ODU with multiple modules in each ckt : 24 HP

(d)Third Floor: VRV ODU with multiple modules in each ckt : 20 HP

(e) VRV ODU : 10 HP For TFA UNIT

(b) VRV type Hi wall 2.0 TR

VRV CASSETTE AC (NS) Make : O GENERAL/MITSUBSHI HEAVY/TRANE (a) VRV type Cassette 1.59 TR

(b) VRV type Cassette 2.0 TR

(c )VRV type Cassette 2.55 TR

(d) TFA UNIT 1800 CFM

FITTINGS & CONTROLLERS Central remote Controller (Touch Screen Type) : Supply, installation, testing & commissioning of the Graphic central remote Controller. It must act as an advanced air conditioning management system to facilitate complete control of VRF air conditioning equipment, It should be user friendly through its touch screen, icon display and color LCD display. Integratable upto 64 remote controller groups (including TFAs) and BMS compatible with ethernet/Wi-Fi communication protocol for remote monitoring. In addition to basic controls such as settings for on/stop,the operation mode & temperature,the air quantity and auto louver can be set.If a problem occurs, an alarm code immediately shows the details of the problem. An external input terminal is provided as standard. External signals enable the following function: central operation/stop,demand control,emergency stop,central operation output,& central alarm output. (a) Imported fittings Y-joints and headers etc. (Refer HVAC Drawings).(NS) Make : O GENERAL/MITSUBSHI HEAVY/TRANE

(b) Corded remote controllers

(c)Touch screen type centrallised controller suitable for indoor units as mentioned above.

REFRIGERENT PIPING WORK Supply, fabrication, installation, testing of Interconnecting refrigerant pipe work with Armacell insulation (19 mm / 13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with Gripple hanger and all external piping shall run in covered cable tray.( for complete system) (NS) Make: Indigo/Rajaco/Lawton

Supply & installation of Rigid CPVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. (NS) Make: Prince/Supreme (a) 40 mm dia

(b) 32 mm dia

(c)25 mm dia

(b) Capacity : 250 cfm (Inline exhaust fans Dia 160 mm / 12 mm S.P)

(c)Capacity : 300 cfm (Inline exhaust fans Dia 200 mm / 12 mm S.P)

(d) Capacity : 500 cfm (Inline exhaust fans Dia 400 mm / 12 mm S.P)

(e)Capacity : DIA 200 MM (Propeller exhaust fans)

INDUSTRIAL ELECTROSTATIC AIR CLEANER EXHAUST FAN DRY SCRUBBER SITC Of Dry Scubber Having 18 G GI Sheet metal enclosure dully powder coated, prefilter and after filter for the uniform distribution of air on high efficiency electronic Air Purification system with very low pressure drop. Dry Scrubber with the efficiency of 90-95% at velocity of 500 FPM down to 2.5 microns. Electrostatic module should have 9 ionization stainless steel spikes for producing crona field and should have all safety features with ESP module charging from the main electical panel does along with limit switches and solid state power supply with in built transformer.(NS) Make: Kruger/Nicotra/Greenheck Capacity: 2500 CFM / 70 mm S.P

FAN SECTION FOR EXHAUST Supply, installation, testing and commissioning of factory fabricated Double Skinned Fan section unit horizontal type fabricated out of extruded aluminium section consisting with 0.6mm pre-plasticized/pre-coated Galvanised steel sheet outside & 0.6 mm plain alvanised steel blower section and Blower shall be didw Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply The Fan section shall be insulated with 23 mm thick & 36 Kg/m³ density PUF foam. It includes Starter panel with accessories. (NS) Make: Kruger/Nicotra/Greenheck Capacity: 2500 CFM / 70 mm S.P

EI work 322- 446:- Wires and Cables (ii) S/E of 3 core PVC copper insulated and sheathed circular flexible wire:- (HSR 31.9) (d) Size 1.50 sqmm (48/0.20 mm)

S/E of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide. (HSR 31.13) (ii) Size 40 mm x 40 mm x 6 mm

Supply and erection of 3 mm thick mild steel sheet duly welded on existing MS angle iron frame for fixing the main switch etc., as required, duily painted with three coats of approved paint including one coat of red oxide. (HSR 31.14)

Supply and erection of blanking sheet in existing distribution board (HSR 31.16)

Supply and erection of miniature circuit breaker/ isolator 240/415 V in the existing distribution board including making necessary connection:- (HSR 31.17- a) Miniature Circuit Breakers of 9 K.A. breaking capacity ii) SP MCB 6 amp. To 32 amp.

ii) SPN MCB of 9 KA breaking capacity 40 amp. to 63 amp.

iii) TPN 40 amp to 63 amp.

Supply and erection of Fittings and Accessories. (HSR 31.18) xxvi) S/E of hexagonal M.S box 1.60 mm thick having each side 8 cms 7.5 cms deep top covered with M.S lid by means of screws including 10 mm dia 30 cm long mild steel rod made into suitable Suspension hook and erected in R.C.C slab for erection of fan, the bottom covered with 3 mm thick bakelite sheet with suitable holes, Painting etc. complete with all labour and material required to complete the job.

S/E of pipe for wiring purpose i/c bends inspection boxes etc., where necessary and painting as required. (HSR 31.21) (xvi) Heavy guage welded Conduit pipe 25 mm dia 1.60 mm thickness on surface. (HSR 31.21

(xxii) Heavy guage welded Conduit pipe 25 mm dia 1.60 mm thickness on flushed. (HSR 31.21

S/E of PVC pipe of 6 kg pressure, laid 1 mtr. Below ground level complete i/c digging & reffling of trench with jointing extra {HSR 31.21 (xxx)} (a) PVC pipe 120 mm dia.

(b) PVC pipe 80 mm dia.

Earthing (HSR 31.22) iii).Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as equired. .

v) Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

(xv) Pdg. And fixing 25mm x 5mm GI strip on surface on in recess for connection etc. as required with all labour and material.

xvi) Pdg. and fixing 4.00 mm dia G.I.wire on surface or in recess for loop earthing as required .

Galvanised Iron (HSR 31.24) (ii) Excavation earth pit 180cm round at top and 90cm at bottom 4.5m deep and refilling the same in plains including supply of necessary charcoal / coke and salt mixture.

(iv) Supply and erection of 60cm x 60cm x 6mm thick galvanised iron plate including necessary bolts and nuts to GI tape.

(v) Providing standard watering tank incluidng down pipe and CI cover with locking arrangement etc.

(vi) Supply and erection of 20mm x 3mm thick lightening conductor GI tape fixed with suitable GI stapples of same size.

(vii) Supply and erection of GI tape 32mm x 6mm thick from earth electrode directly in ground and surface fixed with GI stapples of same size.

(viii) Supply and erection of 25mm diameter 1.5m long lightening GI tube rod tapered into a point at the top with 16cm x 16cm x 3mm thick GI base plate and necessary nuts and bolts with washers.

(ix) Providing and fixing testing joints made of 20mmx3mm thick GI strips 12.5mm long with 4Nos. bolts and nuts with wahsers complete.

UNDERGROUND CABLES (HSR 31.25) S/E of underground cable 1 metre below ground level covered with sand and bricks including necessary connections, digging and refilling of trenches. xxx) 120 sq mm, 3.50 Core cable (Armd)

Supply and erection of under ground cable loose in existing pipe or trenches complete with necessary connections.(HSR 31.26) xxvii) 50 sq mm, 3.50 Core cable (Armd)

xxix) 95 sq mm, 3.50 Core cable (Armd)

xxx) 120 sq mm, 3.50 Core cable (Armd)

Supply and erection of suitable compression type brass cable glands for underground Cable. .(HSR 31.28) (iii) 50 sq mm, 3.50 Core cable (Armd)

(iv) 95 sq mm, 3.50 Core cable (Armd)

(v) 120 sq mm, 3.50 Core cable (Armd)

Miscellaneous (HSR 31.35) (i) Supply of M.S. Pipe (B-Class) for suspension rod of ceiling fan including threading if required. (a) 15mm dia

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work. {HSR 31.35-(ix)} (g) 50 sq mm.

(i) 95 sq mm.

(j) 120 sq mm.

Supply and erection of PVC unsheathed copper conductor cable single core 1100V grade in pipe of suitable size excluding cost and erection of pipe. (HSR 31.40) i) size 1.5 Sqm

ii) size 2.5 Sqm

iii) size 4.0 Sqm

iv) size 6.0 Sqm

(v) Size 10.0 Sq mm

(vii) Size 25.0 Sq mm

Supply and rection of double door sheet enclosure distribution board suitable for MCB and ELCB etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work. (HSR 31.41) (ix) 4-way , TP&N ( Vertical)

(x) 8-way , TP&N ( Vertical)

Supply & erection double pole /Four pole Residual current circuit breaker (RCCB/ELCB) suitable suitable for operation on 240/415V, 5 Hz. AC supply installing in existing sheet steel enclosures including necessary connections & bonding to earth with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer- in -Charge of the work. (HSR 31.42) (viii) 40A/240V DP ELCB with 100 mA sensitivity.

Supply and eretion of PVC conduit pipe ISI marked (Medium) recessed in wall/ceiling etc. (HSR 31.44) (b) 25 mm dia

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary conneciton, complete in all respect. (HSR 31.56) (i) 10 amp. 1 way switch

(ii) 10 amp. 2 way switch

(iii) 20 amp.switch

(iv)10 amp. Socket

(v) 16 amp. socket

(vi) Bell Push

(vii) Fan regulator

(viii) Call bell Ding-Dong (Monica)

(ix) Blanking Plate

Providing and fixing GI concealed sheet metal boxes with inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respect. (HSR 31.57) 1 & 2 Modules

3 Modules

4 Modules

6 Modules

8 Modules

12 Modules

Supply and erection of PVC pipe ISI marked (Medium) recessed in wall/ceiling etc. incluidng the cost of pVC bands. (HSR 31.58) PVC pipe of 32 mm dia

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of Engineer-in-Charge of the work. (HSR 31.78) i) 2 Pair Telephone wire

ii) 10 Pair Telephone wire

iii) 20 Pair Telephone wire

(iv) 50 Pair Telephone wire

S/E/T/C of RG-11 COAXIAL cable in existing PVC conduit/PVC channel complete in all respect with all labour and material required to complete the job in all respect. (HSR 31.79)

S/E/T/C of Cat-6 cable in existing PVC conduit/PVC channel complete in all respect with all labour and material required to complete the job in all respect.(HSR 31.80)

Supply & Erection of Wall / free standing floor mounting dust & vermin proof campartmentlized cubical panel made out of 2mm thick CRCA sheet, required hardware for bus bar and cable alley seperating switching compartment & supporting suitable channel duly painted by 2 coat of zinc / red oxide primier followed by 2 coats of powder coating in grey or required shade after rinsing. The panel having complete with PU / Neoprane rubber gasket of not less than 3mm thick, seperate detachable gland plate / MS Channel hinged door with interlocking arrangement for equipment /switch wear.Transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to busbar bakelite sheet 3mm thick for separetely cable allely to BBC from switch chamber extended solid copper bars up to cable alley shall be provided for outgoing connection which shall be paid as extra items. Side walls & cable alley compartments shall be having bolted type doors with detachable extension type structure.the pannel will be complete with copper control wiring and fuse protection.(only outer area on all sides shall be measured)( HSR-31.63)

Supply & fixing of copper bus bar duly tinned by means of SMC/DMC type high tensile nuts & bolts, spring washers fixing to same in existing panel i/c bending,cutting in required shape and size with insulation & colour coding heat shrinkable PVC insulation complete in all respect.( HSR-31.64)

Supplying&Fixing of Rotary handle for on/off operation of existing MCCB in the L.T. panel including fixing the same in position with all labour and material required to complete the job in all respect. (H.S.R.-31.66) a) Rotary handle up to 125 A, MCCB

b) Rotary handle above 125 A, MCCB

Supply and erection of moulded case circuit breaker single pole/four pole on wall or on existing pedestal including bonding to earth and necessary connections. (HSR 31.69) (iv) 4 pole MCCB 6amp. to 63 amp

v) Four Pole MCCB 100 Amp

vii) Four Pole MCCB 300 Amp to 400 Amp

S/E of ISI marked propeller type ventilation fans (Exhaust fan) Size 300 mm, 1400 rpm Heavy Duty suitable for single phase A.C. 230 Volts, 50 HZ supply, A.C capacitor run conferming to IS:23/2/67 , complete with mounting ring with four no.s fixing holes without regulator as per rate contract specifications.with all labour and petty material required.(Havell's - Make & Model -Torboforce or Cormpton Greaves). Orient/hawells (NS)

Supply and erection of 300 mm aluminium anodized louver shutter for exhaust fan (Thickness of frame 1.00 mm & blade thickness 0.80 mm) including all labour and other petty material required to complete the job. (Canon, National-Make) (NS)

S/E of recessed type 42 Watt full window glare free opal diffuse LED Panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 4600 or above in cool day light (5600K to 6500K), Power factor >0.95, CRI (Ra) >80, LED Lamp efficiency ≥ 140 lm/w, Average life > 50000 hours, complete with all accessories as required with connections (Industrial) Make: Havells/Bajaj/Phillips (NS)

Supply & Erection of electric ceiling fan capacitor type sweep size 1200mm type of regulator fitted in ceilling fan electronic ISI marking energy efficient star rating 5 star complete in all respect. (NS) Make:- Orient/Havells/Bajaj

Supply & Erection of 300 mm Sweep wall mounting fan with pull cord control for speed and oscillation including the cost of all petty material required to complet the job upto entire satisfaction of Engineer-in- Charge (NS) Make:- Orient/Havelles/Bajaj

S/E of surface/wall mounted ≤20W integrated LED 4 feet fitting with Epoxy Powder coated white/Grey extruded aluminium channel housing for efficient heat dissipation. Total system lumen of 20 watt LED should be ≥ 2000 or above in cool day light (5700K to 6500K), Power factor >0.95, CRI >80, Average life >50000 hours. Complete with mounting Brackets & accessories as required with connections(Industrial) Make: Philips, Havells, Wipro, Bajaj. (NS)

Supply & errection of 9 W bulk head light with high efficient LED’s, CCT‐6500 K,CRI >70, Lumens ≥ 1000, with polycarbonate sheet and Ingress protection IP‐65, Driver shall be of constant current type, operating temperature from ‐10 to +50 degree celcius, power factor>0.90, rated voltage 220‐240V AC working range:‐ 140‐270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection ‐ Inbuilt 5KV, optional 10KV with external Surge Protection device. Complete in all respect with the entire satisfaction of Engineer‐in‐Charge. (NS) Make:- Phillips/Bajaj/Havells

Supply and erection ≤ 9W LED Mirror Light made of high Grade Coloured ABS and all other petty material required to complete the job upto entire satisfaction of Engineer In Charge & having following specification :- (NS) PF - ≥ 0.90 THD (%) - ≤ 20 Average Life - ≥ 30000 Burning hours Lumens Outpur ≥ 865 operating temp. - 10°C to 45°C Electronic Driver - Integral Electronic Driver (SMPS based Constant current supply) with output short circuit Protection, Surge Voltage Protection Make:- Phillips/Bajaj/Havells

Supply and erection of ≤ 50W LED flood light having following specification IP voltage –AC 100-265V, total power consumption – 50 W (i/c driver), Lamp Luminous efficiency - >90 lm/W, Lumens - >7200 lm, Colour-cool white, CCT - 5000-6000K, CRI-more than 70, operating tempracture = -35°C to + 50°C, IP rating luminiare - IP65, IP rating LED module - IP67, power factor = ≥0.95. Complete in all respect with the entire satisfaction of Engineer-in-Charge. (NS) Make:- ISI Fisture

Supply and erection ≤ 24 W Flexible LED strip for Cove Lighting with flexible PCB, Dual layers, of size 5000 mm x 10mm x 2mm with all other petty material required to complete the job upto entire satisfaction of Engineer In Charge & having following specification :- (NS) Product Life - ≥ 30000 Burning Hours P.F.- ≥ 0.50 operating temp. - 10°C to 45°C Make:- Phillips/Bajaj/Havells

Providing and fixing modular type accessories of approved make in existing box (NS) including fixing and making necessary conneciton, complete in all respect. i) S/I/T/C TV socket single shutter one module, complete in all respect including making necessary connections and labour etc.

iv) S/I/T/C RJ-11 one module, complete in all respect including making necessary connections and labour etc. (NS)

v) S/I/T/C RJ-45 one module, complete in all respect including making necessary connections and labour etc (NS).

S/I/T/C of push ON/OFF type 25 A modular type motor starter switch (white color) for AC's including the cost of petty material required to compete the job upto entire satisfaction of Engineer-in-charge. (NS) Make;- Schneider/Crabtree/Athena

Supply, installation, testing & Commissioning of Telephone tag block including DP box with loking arrangement Make: Krone (NS) i) 10 pair

ii) 20 pair

iii) 50 pair

UPS PANEL INCOMER 2 Nos. 100 amps 4P MCCB(25 KA) METERING & INDICATION 1 set of R,Y,B phase indicating lamps 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB 1 No. (0-100A) Ammeter with ASS with 3 nos. 100/5A CT's BUS-BAR 1 Set of 160A TPN Copper Bus Bar with colour coded PVC Sleeves OUTGOINGS 2 Nos. 63 A, 4P MCB (10kA) 3 Nos. 40 A, 4P MCB (10kA) 3 Nos. 32 A, DP MCB (10kA) UPS PANEL as described above (NS)

Supply, Installation and commissioning of 20 KVA UPS with battery bank Each UPS of 20 KVA/16 KW should have following specifications in addition to tender requirements : True online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/ three phase output with SMF batteries Suitable for 30 Min backup on Full load at 0.8 output power factor. Input voltage range 360- 478V at 100% load, 220-478 V @ 50% load. Input power factor 0.99,Output THD is less than 3% for linear load. Less than 5 % for nonlinear load. Crest factor 3:1, over load 125% for 10 min, 150% for 1 min and should be able to operate continuously at 115% load on bypass mode. Battery voltage Adjustable from 384VDC to 480 VDC on site. Battery Bank sizing as 42 AH x 40 nos. Battery type should be Valve regulated lead-acid (VRLA) of make Exide/Panasonic/QUANTA/Rocket. Audible noise level should not exceed 63 dB (A). Parallel communication port, RS232. USB EPO and SNMP interface, BMS interface are required. EMC-IEC62040-2 safty-IEC62040 II operating temperature 0 40 deg C, relative humidity 95% Non-Condensing. No derating e to 40 Deg temp.. UPS shall have inbuilt Input Isolation Transformer. static by pass and manual by pass built in required. Third party test report through accredited lab like TUV is required for IEC 62040-3 and IP20. UPS should be provided with environment monitoring probe to measure temperature and humidity of UPS room. UPS shall have dust filter sat Air Inlet level to improve UPS reliability. The UPS should be provided with phase corrector system. LCD Display indicating all important parameters. SNMP software should be compatible to Microsoft windows XP, Windows Vista, Window 8, Window server 2003 R2, UPS software should be compatible to google chrome, Mozilla fire fox and Microsoft internet explorer. Battery rack, battery interlinks battery breaker, battery to UPS cable as required should be provided with UPS systems. Make: Eaton, Elnova, Peagasus, GE, Gutur, Emmerson. (NS)

Lift:- Supply, erection, testing and commissioning of 16 passengers Capsule Type Electrical Traction Elevator, Roomless , Gearless With Speed of 1.00 mtr./ Second serving 4 Stops & 4 Opening (G+3) with SS Honeycomb finish, 5 Side Observation Glass, hand rail, Glass Vision Panel of 500mmx150mm with protection grill on each door, decorative false ceiling with LED Lights, blower / rotor motor fan & Antiskid PVC Flooring on heavy duty M.S plateform to be erected in accordance with the following Technical Specification and as per latest IS Specification. (NS) (i) Make of Lift :- OTIS / KONE / MITSUBISHI /ORBIS ii) Type & capacity : Passanger Elevator 16 person iii) Speed mps : 1.0 mtr per second iv) Travelling (max) in mtrs : Aprrox. 12 mtrs v) Serving : (G+3) 04 stops, 04 opening all opening on same side) vi) Power Supply : 415 V, 3 phase, 50 HZ A C supply. vii) Control : Simplex full collective control with or without atendant. viii) Operation : Automatic ix ) Motor : Permanent Magnet Synchronous ElectricTraction Gearless Motor to be hoisted on guide rail within the elevator hoistway x) Location of Motor : Motor to be hoisted above the rail within the elevator hoist way. xi) Type of Drive : A. C . Variable Voltage Variable frequency with 16 Bit Microprocessor xii) Car Size : A s per manufacturer design. xiii) Hoist way available : 2700 mm Wide x 3220 mm Deep xiv) Car Enclosure : SS Honeycomb finish, 5 Side Observation Glass, hand rail, Glass Vision Panel of 500mmx150mm with protection grill on each door, decorative false ceiling with LED Lights, blower / rotor motor fan & Antiskid PVC Flooring on heavy duty M.S plateform, Car Area Inside- 1000Wide x2700 Deep. xv) False Ceiling : SS Honeycomb finish Decorative false ceiling with LED Lights, blower / rotor motor fan xvi) Car Panel : SS Honeycomb finish xvii) Flooring : G ,1,2,3, ( Antiskid PVC Flooring ) xviii) Clear Opening of door : 900 mm wide x 2000 mm high xix) Door Operation : Automatic DC/AC with adjustable Door Opening and closing timings with center opening sliding door xx) Door Frame : Stainless steel in hair line finish Other features: i) Battery operated intercom, emergencfy alrarm and emergency light with maintenace free rechareable battery. ii) Adjustable guide shoes.(Ensures good ride comfort) iii) Digital direction & position indicator in Car & at all landing. iv) Integral full height car opening panel with luminous combined with direction arrows, overload warning indicator and services cabinet v) Hands free press and speak intercom with EPABX for three way communication. vi) Automatic rescue device with Manual rescue Lever (to rescue the Passanger in case of emergency) the device will bring the elevators to the nearest floor and open the door automatically in Case of power / phase failure / low voltage. vii) Full height infrared safety curtain( Highly sensitive safety device for safe entrance & exit of the Passanger into the Car & automatic floor announcer. viii) Diffused lighting in car. x) Looking mirror in side of lift car. xi) Face plate Finish : stainless steel in hair line. xii) Face plate : Rectangular. xiii) A three feet high railing shall be provided on car top xiv) The motor shall be high starting torque and low starting current and shall be arranged for self lubrication. xv) Proper weight screen shall be provided at the hoist way. xvi) Fire retardant compound coated traveling cable shall be used. xvi) 2 Phase Device Fire Man Drive & Fireman switch at ground floor xvii) Micro Movements L.E.D. based Buttons. xviii) Load Weighing device with overload bypass feature.(Audio Visual over load indicator in the car) xix) Steel items such as Door Frames Sill Angles, Fascia Plates, Spring Buffers. xx) Braille fixtures, Lift announcement system, Pit ladder, Hand rail , Pressure sensing device & Additional Car Gate Lock. xxi) Two Side Hand Rails in Stainless Steel Finish. xxii) System Capable of withstanding +10% to –10% Variation in Supply Voltage Fluctuations. ( C.V.T should be provided for Protection of lift against Single phase, Low voltage & over voltage) xxiii) Car Platform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel. xxiv) Fire Rated Landing Doors for a Period of One Hour Only. xxv) The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice and vibration. xxvi) A handrail not less than 0.60mtr long and 1.0 mtr. Above floor level shall be fixed adjacent to the control panel. xxvii) The time of automattically closing door shall be minimum 5 seconds and the closing speed shall not exceed 0.25mtr./ Seconds. xxviii) Overspeed governor ( Electro-mechanical device that prevents free fall in case the lift is travelling at speed more than 10% of the rated speed in downward direction. xxix) All other required features relates the operation of lift by the Handicappeds & Blind person as per instruction of lift inspector.

OIL TANK:- Supplying, unlaoding, placing on foundation testing commissioning of 990 Ltrs. 14 SWG MS diesel oil storage tank duly painted with two coats of primer after pre- treatment and one coat of synthetic enamel paint with manhole, glass gauge, calibration of oil, inlet and outlet connections with gate valve, drain plug, piping between tank and engine, vent etc. mounted on suitable MS staging to maintain gravity flow of diesel oil from tank to DG Set including painting. (NS)

Supplying, Erecting, testing, commissioning of additional following dia. exhaust piping with heat resisting aluminium cladding insulation wrapped all along the pipe including fixing of pipe with MS clamps on walls/ ceiling complete as required. (NS) (a) 125mm

Telephone system:- Supply, Installation, Testing & Commissioning of IP PBX System complete As per Specification. Digital, Non-Blocking, ISDN / ATM, IP ready on control cards, Communication Server with SIP. Equipped with: Industry Standard IP Communication Server with RPS – 02 Nos. a) IP/SIP Users : 2 Nos. b) digital users : 2 Nos c) Analog Users with CLIP : 50 Nos d) P & T Lines : 02 Nos e) PRI Lines Interfaces : 02 Nos. f) DISA & DOSA Facility g) Remote Maintenance Facility h) IP Desk Phone Based Operator Consoles with 28 Key DSS: 02 Nos. i) Web Based Management Software: 01 j) Call Accounting Software: 01 k) 100 Ports Integrated Multi-Level Automated Attendant l) Integrated voice mail 08 port – 01 NosGSM Handset. m) Power Back up for 1 Hour – 1Nos n)VOIP Capability o) System Documentation on CD-ROM p) Support for OFC Connectivity q) Expandable up to 10,000 ports. r) For Caller ID, Analog Push Button Phone Should have the capability of CLI Only on PRI Lines/Trunk lines s) Music In Hold - 01 No. t) Paging Interface / Fire Alarm Interface - 01 No. u) Voice mail (08 Ports) - 01 No. v) Call billing software - 01 No. Exchange described as above (NS)

Supply, installation, testing and commissioning of IP based Telephone system with 2 Lines & HD voice, graphical LCD. (NS)

Supply, installation, testing and commissioning of Analouge Telephone system. (NS)

Supply Installation testing & commissioning of AP Management License including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (MAKE : RUCKUS/CISCO/ARUBA) (NS)

Supply Installation testing & commissioning of Cat 6 UTP Cable including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (MAKE : DigiLink/AMP/Dlink) (NS)

DATA & SWITCH:- Supply Installation testing & commissioning of 24 Port POE Access Switch with the 3 years comprehensive NBD and 24x7 direct OEM TAC Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : Access switch should support minimum 16K MAC addresses and minimum 4K active VLANs. Access Switch should have 24 ports of 10/100/1000 RJ45 PoE/PoE+ with 370 Watt of PoE Budget and 2 ports of 1/10G SFP+ fibre Access Switches should support non-blocking switching fabric capacity of min 132Gbps (including stacking BW) and min forwarding capacity of 98 Mpps. Access switch should support min 16K MAC addresses and min 4K active VLANs. Access Switch should have dedicated stacking ports of min stacking BW of 40Gbps with support of minimum 9 units stacking.Access Switch should have stacking capability with minimum stacking bandwidth of 40 Gbps and should support a minimum of 9 units in a stack. Stacking cables must be supplied with switch.Access switch should support up to 8 hardware queues per port Access Switch should support full Layer 2 features like STP, RSTP, LACP, ACL, QoS, IGMP v1/v2 from day 1. Access Switch should support basic L3 features like IPv4 & IPv6 static routing, Layer 3/4 ACLs, ECMP, virtual interfaces and routed interface (NS) Make:- RUCKUS/CISC/HP/Alcatel Switch should have advance Layer 3 features like, IPv4 and IPv6 dynamic routes, RIPv1/v2, OSPFv2, OSPFv3, VRRP, VRRPv3 and PBR from day one.. Access Switch should support minimum 1K IPv4 routes. The Access Switch should support IPv6 management features like IPv6 ping, IPv6 trace route, IPv6 Telnet, IPv6 TACACS, IPv6 and IPv6 RADIUS. All Switches and Transceivers should be of same OEM make.Access switch should support minimum 2K ACL rules ACL per Switch.Access switch should support SNMP v1/v2/v3, SSH, NTP and web managementAccess switch should have 1G of RAM and 2G of Flash Memory.Access switch should have minimum 2Mb Buffer memory support.The Access Switches should be quoted with 3 years warranty including 8 X 5 OEM direct Technical Assistance Centre (TAC) support and Next Business Day hardware replacementThe OEM must feature in the Leaders/ Challengers/ visionaries segment of the Gartner Magic Quadrant for Enterprise Wire and Wireless Networking published in year 2016 or latest.Manufacture Authorization form required from OEM.MAKE : RUCKUS/CISCO/HP/Alcatel.

Supply Installation testing & commissioning of 24 U Server rack with Accesserieoes including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) MAKE :VPRO/Dlink/DYNAMIC

Supply Installation testing & commissioning of 15U Server rack with Accesserieoes including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE :VPRO/Dlink/I-DYNAMIC

Supply Installation testing & commissioning of Cat 6 UTP Cable including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) (MAKE : Molex/Siemon/Dlink)

Supply Installation testing & commissioning of Category 6-7ft Modular RJ-45 UTP Patch Cord including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) MAKE : MOLEX/dlink/Siemon

Supply Installation testing & commissioning of Category 6 RJ-45 UTP Information Outlet for Field Side including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : MOLEX/Dlink/Siemon

Supply Installation testing & commissioning of Face plate Single port with Shutters. including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) MAKE : MOLEX/SIEMON/Dlink

Supply Installation testing & commissioning of Fully Loaded Jack Panel, 24 port including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. MAKE : MOLEX/Dlink/Siemon

Supply Installation testing & commissioning of 12-core Multimode OM3 OFC including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) (MAKE : Molex/Siemon/Dlink)

Supply Installation testing & commissioning of Om3 Fibre Patch cord duplex including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) (MAKE : Molex/Siemon/Dlink)

Supply Installation testing & commissioning of Black, 12F, 1U, Loaded with, Splice tray, Couplers & Pigtails including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) (MAKE : Molex/Legrand/Dlink)

CCTV :- Supply Installation testing & commissioning of 4MP IP Network Dome Camera with 3 Year Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : MAKE : HYUNDAI/AXIS/PELCO/DAHUA (NS) Image Sensor : 1/3” 4 Megapixel Progressive scan CMOS sensor or better Effective Pixels : 2688(H)x1520(V)) or better Electronic Shutter : Auto/Manual, 1/3(4)~1/100000s Scanning System : Progressive Scanning System : Progressive S/N Ratio : More than 50dB Min. IR LEDs Length : 50m IR Leds : 1 Day/Night : Auto(ICR) / Color / B/W Back Light Compensation : BLC / HLC / WDR White Balance : Auto/Natural/Street Lamp/Outdoor/Manual Motion Detection : Off/On (4Zone, rectangle) Region of Interest : off/on(4Zone) Video Compression : H.265+/ H.265 Resolution : 4MP or better Bit Rate : H.265: 14 ~ 9984Kbps Network Ethernet : RJ-45 (10/100Base-T) Flip : 0°/90°/180°/270° Protocol : HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPOE; IPv4/v6; QoS; UPnP;NTP; Bonjour; 802.1x; Multicast; ICMP; IGMP; SNMP Power Supply : DC12V, PoE (802.3af) Working Environment : -30°C~+60°C / Less than 95%RH (no condensation) Ingress Protection : IP67 Audio Interface : Built-in-Mic

Supply Installation testing & commissioning of 2MP WDR IR Bullet Network Camera with 3 Year Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : (NS) Image Sensor : 1/2.8” 2 Megapixel Progressive scan CMOS sensor or better Effective Pixels : 1920(H)x1080(V)) or better Electronic Shutter : Auto/Manual, 1/3~1/100000s S/N Ratio : More than 50dB IR Distance : 60m IR Leds : 4 Day/Night : Auto(ICR) / Color / B/W Back Light Compensation : BLC / HLC / WDR(120DB) White Balance : Auto/Natural/Street Lamp/Outdoor/Manual Focal Length : 3.6mm Video Compression : H.265+/ H.265 Resolution : 1080P(1920x1080)/1.3M(1280x960)/ 720P(1280×720) Frame Rate (3 Stream) : Main stream 1080P (1~50/60fps) & Sub stream : D1(1 ~ 50/60fps)& Third Stream : 1080P (1 ~ 25/30fps) Bit Rate : H.265: 14K ~ 9984Kbps Motion Detection : Off/On (4Zone, rectangle) Region of Interest : off/on(4Zone) Network Ethernet : RJ-45 (10/100Base-T) Protocol : HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPOE; IPv4/v6; QoS; UPnP;NTP; Bonjour; 802.1x; Multicast; ICMP; IGMP; SNMP Compatibility : ONVIF Digital Zoom: 16x SD Card : Min 128GB SD card support Power Supply : DC12V, PoE (802.3af) Working Environment : -30°C~+60°C / Less than 95%RH (no condensation) Alarm : 1 channel In: 5mA 5VDC, 1 channel Out: 300mA 12VDC Vandal Resistance : IK10 Ingress Protection : IP67 Casing: Metal Audio Interface : 1/1 Channel In/out Intelligence (IVS) : Tripwire, Intrusion, Object Abandoned/Missing , Advanced Intelligent Functions : Face Detection MAKE : HYUNDAI/DAHUA/PELCO/SAMSUNG (NS)

Supply Installation testing & commissioning of 2MP IR Dome Network Camera with 3 Year Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : Image Sensor : 1/2.8” 2 Megapixel Progressive scan STARVIS CMOS sensor or better, Effective Pixels : 1920(H)x1080(V)) or better Electronic Shutter : Auto/Manual, 1/3(4)~1/100000s S/N Ratio : More than 50dB , IR Distance : 20m , IR Leds : 10 , Day/Night : Auto(ICR) / Color / B/W, Back Light Compensation : BLC / HLC / WDR(120DB) White Balance : Auto/Natural/Street Lamp/Outdoor/Manual,Focal Length : 2.8mm Angle of View : H: 110° ,V: 58°, Video Compression : H.265+/ H.265 Resolution : 1080P(1920x1080)/1.3M(1280x960)/ 720P(1280×720) Frame Rate (3 Stream) : Main stream 1080P (1~50/60fps) & Sub stream : D1(1 ~ 50/60fps)& Third Stream : 1080P (1 ~ 25/30fps) Bit Rate : H.265: 14 ~ 5632Kbps, Motion Detection : Off/On (4Zone, rectangle), Region of Interest : off/on(4Zone) Flip : 0°/90°/180°/270°, Network Ethernet : RJ-45 (10/100Base-T) Protocol : HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPOE; IPv4/v6; QoS; UPnP;NTP; Bonjour; 802.1x; Multicast; ICMP; IGMP; SNMP, Compatibility : ONVIF Digital Zoom: 16x, SD Card : Min 128GB SD card support Power Supply : DC12V, PoE (802.3af) Working Environment : -30°C~+60°C / Less than 95%RH (no condensation) Vandal Resistance : IK10,Ingress Protection : IP67 Audio Interface : Built-in-Mic, Intelligence (IVS) : Tripwire, Intrusion, Object Abandoned/Missing ,Advanced Intelligent Functions : Face Detection MAKE : HYUNDAI/AXIS/PELCO/DAHUA (NS)

Supply Installation testing & commissioning of 2MP 30x IR PTZ Network Camera with Mounting Kit 3 Year Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : (NS) MAKE : HYUNDAI/AXIS/PELCO/DAHUA Image Sensor : 1/2.8” 2 Megapixel Effective Pixels : 1920(H)x1080(V)) or better Electronic Shutter : 1/1s~1/30000s S/N Ratio : More than 55dB IR Distance : Distance up to 150m IR Leds : 4 Day/Night : Auto(ICR) / Color / B/W Back Light Compensation : BLC / HLC / WDR(120DB) White Balance : Auto,ATW,Indoor,Outdoor,Manual Focal Length : 4.5mm~135mm Angle of View : H: 67.8° ~ 2.4° Optical Zoom : 30x Focus Control : Auto/Manual ,Pan/Tilt Range : Pan: 0° ~ 360° endless; Tilt: -15° ~ 90°,auto flip 180° ,Manual Control Speed : Pan: 0.1° ~300° /s; Tilt: 0.1° ~200° /s , Presets : 300 , PTZ Mode : 5 Pa ern, 8 Tour, Auto Pan ,Auto Scan Power up Action : Auto restore to previous PTZ and lens status a er power failure , Video Compression : H.265+/ H.265 Resolution : 1080P(1920×1080)/1.3M(1280×960)/720P(1280× 720) Bit Rate : H.265: 448K ~ 8192Kbps Region of Interest : Support Flip : 180° Network Ethernet : RJ-45 (10/100Base-T) Protocol : HTTP; HTTPs; TCP; ARP; RTSP; RTP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPOE; IPv4/v6; QoS; UPnP;NTP; Bonjour; 802.1x; Multicast; ICMP; IGMP; SNMP Compatibility : ONVIF Digital Zoom: 16x SD Card : Min 128GB SD card support Working Environment : -40°C ~ 70°C (-40°F ~ +158°F) / Less than 90% RH Alarm : 2 channel In, channel Out: 1 Vandal Resistance : IK10 Ingress Protection : IP66 Casing: Metal Audio Interface : 1/1 Channel In/out Intelligence (IVS) : Tripwire, Intrusion, Object Abandoned/Missing Certification : CE, FCC,UL Motion Detection : Support

Supply Installation testing & commissioning of Wireless Video transmission Device with 3 Year Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specification : (NS) Wireless Feature : Wireless Standard : IEEE802.11 a/n Working Frequency : 5745~5825MHz(extended range: 4920~6100MHz) Wireless Speed : 300Mbps Modulation Mode : OFDM Antena : Built-in-antena : gain 15dbi Output Power : 27dBm Receiving Sensitivity : -74dBm@65Mbps,-96dBm@1Mbps Transmission Distance: 0-3KM Wireless Direction Angle: Horizontal 40°, vertical 15° Power : 1*PoE RJ45(IN: 220V, OUT: 24V/0.5A); Power Consumption : Max. *W Working Temperature : -30°C~+70°C Working Humidity : 5%~95%RH(no condensation) Ethernet Port : 1*LAN RJ45 + 1*LAN RJ45 from passive PoE adapter Encryption Type : WEP/WPA-PSK/WPA2/CCMP(AES)/TKIP Network Mode : Route/Network Bridge Network Protocol : TCP/UDP/ARP/ICMP/DHCP/HTTP/NTP TDMA Enhancement : Support(TDMA eliminate hidden nodes influence and greatly improve one-to-many performance) Webpage Configuration Management : Support Webpage Configuration Long-Distance Communication Throughput Rate : ≤40Mbps@3km Bandwidth Flexible : 5M/10M/20M/40MHz MAKE : HYUNDAI/AXIS/PELCO/DAHUA (NS)

Supply Installation testing & commissioning of Video Management Recorder with 3 Year free comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specifications : (NS) MAKE : HYUNDAI/DAHUA/PELCO/SAMSUNG Main Processor : Intel Dual-core Processor or better Operating System :Embedded LINUX IP Camera Input : 64 Channel or More Two-way Talk : 1 Channel Input, 1 Channel Output/RCA Interface : ≥2 HDMI (up to 3840 x 2160 , Different Source), ≥1 VGA Compression : H.265/H.264 Resolution : 12MP, 8MP, 6MP, 5MP, 4MP, 3MP, 1080P, 1.3MP, 720P etc. Bandwidth : >340Mbps Record Mode : Manual, Schedule (Regular, MD (Motion Detection), Alarm, Analytics), Holiday, Stop / Video Detection : Motion Detection/ Video Loss and Tampering/ Multiple VCA Events Alarm input : ≥16 Channel Relay Output : ≥8 Channel Search Mode : Time /Date, Alarm, MD / Smart Search Backup Mode : USB Device/Network/eSATA Device Network Interface : 4 RJ-45 Ports (10/100/1000Mbps) Ethernet Port : 4 Ethernet Ports Joint Working or 4 Independent 1000Mbps Ethernet Ports Network Function : HTTP, HTTPs, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE,DDNS, FTP, Alarm Server, IP Search etc. User Access : ≥128 users Smart Phone : iPhone, iPad, Android Interoperability : ONVIF 2.4, CGI Conformant Internal HDD : Internal min 8 SATA HDD port , upto 8TB HDD support per slot HDD Mode : Single, Raid 0/1/5/6/10, Support Global HDD Hot-spare eSATA : 1 eSATA Port SAS : 1 Mini SAS Port, for Storage Expansion Front Cover : Support Hot-swap, USB : 4 USB Ports (2 USB 2.0 , 2 USB 3.0 ) RS232 : 1 Port, for PC Communication and Keyboard RS485 : 1 Port, for PTZ Control Power Supply Redudant Power supply : Support Operating Conditions : -10°C ~ +55°C Certifications : CE,UL,FCC

Supply Installation testing & commissioning of outdor 4*4 box including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : STRONGER/MOLEX/AMP)

Supply Installation testing & commissioning of 6TB surveillance hard disk including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : WD-PURPLE/SEGATE

Supply Installation testing & commissioning of Cat 6 UTP Cable including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. MAKE : MOLEX/Dlink/Siemon (NS)

Supply Installation testing & commissioning of Full HD 43 inch LFD including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : HYUNDAI/DAHUA/PANASONIC

Ram Nath Aggarwal