SPECIAL REPAIR TO NP-8/FFL(S) AT AEC TRG COLLEGE AND CENTRE

Amount

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Dismantling timber scantling, unframed, 40 Sqcm and over in section in any position complete all as specified and directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Taking down and refixing shutters in the same opening of any description and Area exc 1.0 sqm but not exc 2.0 sqm each including easing and adjusting and making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed:-

Taking down and refixing shutters in the other opening of any description and Area exc 1.0 sqm but not exc 2.0 sqm each including easing and adjusting and making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down shutters of any description, .area not exc 1.0 sqm each complete all as specified and directed

Taking down shutters of any description, .area exc 1.0 sqm but not exc 2.0 sqm each complete all as specified and directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

Dismantling of water tank of any description of capacity exc. 500 litres but not exc. 1000 litres, removing to store or from the site complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling of AC (corrugated or semi corrugated etc.) sheets including ridges in roof coverings complete all as specified & directed.

Providing and injecting chemical emulsion for Post Constructional Anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion@ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Anti-termite treatment for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Material & labour for 75mm cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in Plinth Protection complete all as specified and directed.

M&L chequred cement concrete tiles 20cm X 20cm X 25mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors, over and including 15mm thick cement screed beeding layer in cement mortar 1:4 complete all as specified and directed.

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard/ dense soil complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in hard/dense soil complete all as specified and directed.

M&L hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection/path complete all as specified and directed.

Forming 12 mm thick expansion joints filled withpre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ complete all as specified & directed.

Providing and injecting chemical emulsion for Post Constructional Anti-termite treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate for floor finishes complete all as specified and directed.

M&L for vitrified light shade tiles in floor of size 600mmx600mmx10mm thick of approved colour laid over and including 15mm thick screed bed in CM 1:6 jointed and pointed with approved materials as per manufacturers instructions complete all as specified and directed.

Material & labour Glazed ceramic White/light shade tiles in vertical surfaces riser of steps ,skirting, dado and pillar of size 350x250mmx7mm /450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4.complete all as specified and directed.

M&L Non Skid ceramic White/light shade tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and 15mm thick screed bed in CM 1:6 complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

Material & labour Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in, built in CM 1:4 complete all as specified and directed.

Material & labour for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM(1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound ISI Marked, of make as approved by AGE(I) complete all as specified & directed.

Material & labour for preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over a coat of primer complete all as specified & directed.

M&L of preparation of new plastered surfaces of wall and applying two coat of distemper oil emulsion white or coloured over one coat of primer( alkali resistant priming paint) complete all as specified and directed.

Preparation of old distempered or painted wall surface such as washing, rubbing down and stopping of distempered and painted surface with alkali resistant priming paint and applying two coat of distemper oil emulsion white or coloured complete all as specified and directed.

M&L Concrete bed to drain pipes 150mm, including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) Type D-2. complete all as specified and directed.

M&L Slat-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as specified and directed.

M&L PCC(1:3:6) type C1 as in benching to man hole complete all as specified and directed.

M&L for precast reinforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in cover slab for manholes and setting in cement mortar 1:4 complete all as specified and directed.

M&L for PCC (1:3:6) type C-1, using 40mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including finishing the top of benching even and smooth using extra cement complete all as specified and directed.

M&L for suspended false ceilling comprising of 6mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

S&F 60 mm thick Machine pressed precast concrete coloured interlocking paver block any shape and size conforming to IS 15658-2006 , M-35 Grade of concrete, with grey cement and no pigment over and including 50mm thick sand cushioning complete all as specified and directed.

M/L 75 mm thick cement concrete(1:4:8) type D-2 using (40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

S&F Pre-cast cement concrete block masonry (1:2:4) Type B-1 (using 20mm graded crushed stone aggregates) with solid blocks, exc. 10 cm in width and setting in cement mortar(1:6), complete all as specified and directed.

M & L Second class soft-wood timber framed and fixed in roof truss scantlings as in repair to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions complete all as specified and directed

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based 0.50mm thick(AZ-150)corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50mm thick(AZ-150) plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) fixed with self tapping screws complete all as specified & directed.

S&F Mild steel flat iron as in wind ties including cutting drilling holes and securing bolts conforming to FE 290 Gde E-165 complete all as specified and as directed.

M&L for 11 to 15mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 Cm but not exceeding 10Cm long complete all as specified & directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or including butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and as directed.

S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

S & F rolled mild steel plates ( plain on chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe 410 W (Gde E. 250) quality ‘A’ complete all as specified & directed

Supply & fixing pressed steel frames for doors with double rebates including necessary fixing lugs lugs, hinges, lock strike plates etc completed size of frame 125x60mm made out of 1.25mm MS sheets complete all as specified & directed.

S&F Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified & directed.

M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed. Notes:- (i) glazing will be measured and paid for separately. (ii) Butt hinge will be measured and paid for separately .

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fixed in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed.

Supply & fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified & directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

Supply & fix butt hinges, 100 mm long of stainless steel, complete all as specified & directed.

M&L for mild steel work conforming to Fe-290 Gde -165 as in hand rail, holdfast, half round or other steel section or core for wooden hand rail strait portion, drilled and countersunk for balusters running bars for doors, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

Supply & fix 125mm size aluminium alloy handles cast type anodized complete all as specified & directed.

S&F aluminium tower bolts 150mm long, of extruded section complete all as specified and directed. .

Supply & fix Aluminium. Sliding door bolts, plate type, complete, 250mm long complete all as specified and directed.

S&F Anodised Powder Coated aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified.

S&F Powder coated aluminium(minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge.

Material & labour for Precast reinforced cement concrete type B0, 1:2:4 (12.5 mm graded aggregate) in door and windows frames, any size, single or double rebated, including ar?rangement for fixing of hinges and fixtures as required complete all as specified and directed.

M&L preparation of old wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of Previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L preparation of new steel surface and applying two coats of synthetic enameled paint over a primming coat of red oxide etc complete all as specified and as directed.

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by AGE(I) complete all as specified & directed. .

Supply, fix 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply, fix 20 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply & fix in PVC connections of 450mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F as in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) fixed with ‘P’ or ‘S’ trap, including making good the disturbed surfaces and to match with existing surface complete all as specified and directed.

Supply & fix white plastic seat cover for W.C.(E.T.) white including M.S. CP or aluminium hinging device complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting exc 10 cm but not exc 20 cm girth all as specified.

M&L for loose filling with aggregate of gauge 80 to 150mm of broken bricks complete all as specified & directed.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F as in repair 20mm bore Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC (SWR) vent cowl of 75mm bore, any radius complete all as specified & directed.

S&F PVC (SWR) vent cowl of 110mm bore, any radius complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F PVC (SWR), junction single, (Single T) equal or unequal 110 mm bore complete all as specified and directed

S&F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC(SWR) bends 110mm bore provided with access door, any radius complete all as specified & directed.

S&F in repair PVC(SWR) bends any radius of 75mm bore provided with access door, any radius complete all as specified & directed.

S&F for 110 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.

Supply & fix in repair bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fix in repair angular valve, 15 mm dia, cast copper alloy, chromium plated, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm White ( minimum), with grating and union for discharge pipe ( excluding flushing cistern, flush pipe , and waste pipe) , fixed in repairs including connections to flushing pipe and outgoing complete all as specified and directed.

S&F Urinal spreader as in repair of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified & directed.

S&F as in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling complete all as specified and directed.

Supply & fix in repair pillar taps cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

M & L repair to Pillar/Column (cross sectional area =15 square cm) by providing PCC(1:2:4) Type B-0 and finished with CM(1:3) after taking down of damaged portion of RCC work by using required formwork and providing same finish as existing surface complete all as specified and directed. (Height of work to be considered upto 3.00m from FFL of Ground Floor.) (Note : Wherever reinforcement is required to be provided will be paid separately under relevant item of this BOQ)

M&L for mild steel TMT bars 8 mm dia as in stirrups, spacers and binders for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

S & F stack clamps out of 100 mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof complete all as specified & directed.

Taking down carefully surface aluminium point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including PVC casing-caping not less than 32x12 mm ISI marked ivory colour with all fittings / fixing accessories and sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting cover plates with frame for mounting of modular switches, sockets, fan regulators etc as required for the following :-

(a) One light point controlled by one switch 5/6 AMP.

(b) One fan point controlled by one switch 5/6 AMP.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches .

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including PVC casing-caping not less than 32x12 mm ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame for mounting modular switches, sockets as required for 3 pin 16 amps socket outlet controlled by one switch.

S&F angle holder, insulated polycabonate body with back plate complete all as specified and directed.

S&F modular switch one way 6 amp 1 module complete all as specified and directed.

S&F modular switch one way 16 amp 1 module complete all as specified and directed.

S&F modular socket 6/16 - 2/3 pin combined 2 module complete all as specified and directed.

S&F modular socket 6 amp 2/3 pin combined 2 module complete all as specified and directed.

S&F modular hum free electronic step fan regulator, 100 watt 2 module complete all as specified and directed.

S&F MCB distribution board SPN 08 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door (double door) , recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and directed.

S&F MCB distribution board VTPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and directed.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete all as specified and directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

S&F LED batten (1.2 m) made of aluminium housing with a PC glossy difusser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete all as specified & directed.

S&F energy efficient recessed/surface mounted LED luminaire 36 Watt suitable for 2'x2' grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable in renewal of any type luminaire as required complete all as specified & directed.

S&F MCBs as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

Single pole 6 to 32 amp.

Single pole and neutral (SPN) 40 amp.

Three pole 63 amp.

S & F MCCB 125 Amp, 4 pole, 25 KA complete all as specified & directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC)complete all as specified & directed.

M&L earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm x6.0mm thick buried directly under ground vertically to a depth not less than 2.25 meter below ground level with top edge of the plate at a depth not less than 1.5m below ground level connected to and including galvanized iron wire 4.0mm not exceeding 7.5meters for each earth without protection pipe, including test point by means of bolts, nuts, check nuts, and washers made out of GI all as shown on plate No 5 of SSR Part I to the extent applicable to this item including necessary making PCC pit of size 0.3 m x 0.3 m x 0.3 m (inner size) in mix 1:3:6 type C1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 6 mm dia MS bars 3 Nos both ways with lifting hook made out of 6 mm dia bar and testing on completion to achieve value complete all as specified and directed.

S&F LED 35 Watt streetlight made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LED's with secondary optics and IP 65/66 protection complete with fixing arrangement and connection as directed

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 35sqmm, 3.5 core including jointing materials such as cable glands & lugs etc Complete all as directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed. ( Note : Punned thickness shall be considered for payment purpose)

Supply and laying unreinforced precast concrete cable cover, class LV, type 1 with flat, size 250 mm x 150 mm x 40 mm c complete all as specified and as directed.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete all as specified and as directed.

Taking down carefully aluminium submain wiring with PVC surface conduit and making good disturbed surfaces complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Schedule of credit amount of Rs 1,57,532.00 to be deducted during AOC

SHIV SHANKAR MISHRA

CREATIVE CONSTRUCTION

GHASI RAM SAHU

Dev Enterprises

SHRI KRISHNA CONSTRUCTIONS