PROVN OF 05 X SACTIONED WORKS AT 2003 STN UNDER GE (AF) GURGAON

Excavation in post holes (or similar holes) in hard /dense soil each n exe 0.5 cu.m, gettting out, returning, filling in and ramming earth or broken rubble mixed with earth around , in layers not exeeding 25cm, watering, and removing surplus soil to a distance n exe 50 m and making good surface complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 1.50 km and n exc 5.0 km depositing outside of MOD land or where directed

Hardcore of guage exc63mm,Broken bricks, spread & leveled in two layers n exc. 15 cm thick , watered & rammed to a true surface

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregates) as in foundation filling and mass concrete , post holes, cills, steps; seismic and other similar bands, plinth courses, string courses, ramp, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , on roofs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, etc including necessary formwork complete all as specified and directed by Engineer-in-Charge.

S&F rolled sections, MS Angles, MS tubular Structures, MS Channels, Tee, etc. (Fe 410-W Gde-E-250 quality-A) as in main and cross beams, hip and jack rafters, purlins , posts,trusses (framed or unframed) structures where connected to common rafter and running rails and guides for sliding doors, fixed with angles clleats or other connecting plates all as specified.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,with riveted, bolted or welded attachment Fe-410-W(Gde E-250) quality B.

M&L for preparation of new surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surface over 10cm width or girth complete all as specifed. (Note : Design and colour shall be any type as approved by Engineer-In-Charge.)

M&L for surface dressing upto a depth of 15 cm (on average) as in soft/loose soil all as specified and directed

M&L for 75 mm thick PCC 1:4:8 ( 40 mm aggregate ) as in subbase all as specified

Machine pressed precast concrete glossy interlocking color rubberised paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade finishes All as specified and dircted

M&L for 25 mm thick sand cushioning including watering and consolidations etc complete all as specified and directed.

Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed

M&L Rendering 10mm thick in Cement Mortar 1:4 (Externally) on Fair Faces of Brick Walls finished Even and Smooth without using Extra Cement and applying two coats of cement based paint complete all as specified and as directed.

Supply and fixing factory made uPVC door/window frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

M&L for 8 mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes, fixing in frames with all allied fittings required complete all as specified

Supply and fixing factory made uPVC white colour Three track three panels sliding door with fly proof S.S. wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required). stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fastener 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge.(Rates are inclusive of Glass and wiremesh).,

M&L for Virified Ceramic tiles light/ coloured shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm screed bed complete all as specified and directed

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa with hot dip alloy of 55% Al, 43.5% Zinc and 1.5% silicon and finished with resin coat on both side

S&F pre-painted mangalore pattern galvatume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour and shape( conical, round etc) as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding/ridge to wall, fixed with self tapping screws as specified and directed by Engineer-in Charge

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out all as completed.

Excavation in trenches n.exc 1.50mtr wide and 1.50mtr in depth for foundation etc or for shafts, wells cessipts, manhole etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr deth and getting out in soft /loose soil etc complete all as specified and as directed

Removing excavated soil/ building material/debries to a distance exc 250 mtr but not exceeding 500 mtr and depositing where directed etc complete all as specified and directed

Returning filling in, with soil inlcuidng spreading, levelling, watering and well ramming in layers not exc 25 cm thicks etc complete all as specified and as directed

M&L for cement concrete 1:2:4 typeB-2 (using 40mm graded aggregates) as in foundation and mass concrete etc complete all as specified and directed

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) foundations, including rafts, footings, foundation ,beams; plinth beams; bases for columns, etc.; basement slabs, under- eamed piles and mass concrete complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Columns, pillars, piers, posts and struts complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Slabs including roof beam supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs,stairs and in shelves and the like complete all as specified and as directed .

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter all as specified.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) all as specified.

M&L Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. all as specified.

M&L for fly ash brick work straight or curved on plan exc 6.0 mtr mean radius built in CM 1:4 etc complete all as specified and directed

M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:6 finished surface even and smooth without using extra cement.Note the area includs in this up to 4th stories building complete all as specified and as directed .

M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:4 finished surface even and smooth without using extra cement complete all as specified and as directed .

M&L for 5mm thick Rendering on ceiling surface fair faces of brick work or concrete sureces in Cement Moratar 1:3 finished surface even and smooth without using extra cement complete all as specified and as directed .

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F powder coating anodised aluminium section for shutter/frame for door, window and ventilator complete all as specified.

S & F powder coated frame sections for doors and windows approved and fixed all as specified and directed (Note : (i) Paneling such as glass , Gauge etc will be measured and paid saperately.(ii) The rate quoted under this item deemed included for necessary jointing cleates, glazing clips, alluminium beading, screws, rubber packing and locking devices & in built handles for sliding windows. However, no element on account of weight will be taken into consideration for these item.(iii) Floor door spring/locks/tower bolts/ handles/ door closure/hinges for doors measured saparately.(iv) Size of door / windows shall be all as directed at site.(v) Grills will be measured saparately.(vi) Second class hard wood batten of appropriate size to be inserted inside the frame for fixing hinges and the same is included in the rate quoted.)

S & F plain sheet glass 5 mm thick tinted, fixed to aluminium doors/ windows / ventilators complete all as directed by Engr-in-Charge (Note:- Beading/rubber packing is included in the rates for aluminium sections above.)

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125x60/105x60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-0 (12.50 mm graded aggregate) back of chowkhats and incl two coats of synthentic enamel paint all as specified.

S&F in repairs Factory made solid panel moulded PVC door shutter wood grain 30mm thick(style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall becovered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottim rail. Penelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F PVC wood grain moulded Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS Square tub, suppling & fixing in opening as per specification and drawing.

S&F 100mm Butt hinges, meduim weight, cold relled stainless steel and fixed

S & F for aluminium anodised, barrel tower bolts of extruded section 125mm long and fixef

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

S&F 30 mm thich 2nd class Hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, guaze etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securiing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats complete all as specified and as directed .

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed .

S & F for Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed .

S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of exctruded sections or cast aluminium alloy and fixed.

M&L Glazed coloured ceramic tiles in vertical surfaces 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed .

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and directed

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and directed

M&L 25mm thick Cement concrete 1:2:4 type B-O(using 12.5mm graded aggregate) as in flooring, finished surfaces even and smooth without using extra cement complete all as specified and as directed .

S&F 15 mm bore CPVC tube all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed .

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed .

S & F 15mm bore Bib taps, fancy type chromium plated cast copper alloy with crutch or butterly handle, screwed down, screwed with cup for iron pipe or for brass ferrule and fixed complete all as specified and directed

S & F 15mm bore Stop Valve/ angle valve fancy type chromium plated , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends with cup for iron pipe or for unions and fixed complete all as specified and directed.

S & F 15mm bore Pillar taps central hole Basin mixer with regular spout without popup waste system with 450 mm long braided hosedd 20 mm carttridge size fancy type, cast copper alloy, chromium plated, complete all as specified and directed.

S & F 15mm bore brass CP wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting & wall flange fancy type, cast copper alloy,chromium complete all as specified and directed.

S & F single towel rall 450mm long fancy type chromium plated fixed with PVC plug and steel screw complete all as specified and directed.

S & F towel ring round with round flange fancy type cromium plated fixed with PVC plug and steel screw complete all as specified and directed.

S & F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

M & L in repair for hand shower (health faucet) with 8mm dia 1.20 mm lonf flexible tube and wall hook complete all as specified and directed.

S & F in repair for PVC conection 15 mm size with PTMT nuts of length 450 mm long

S & F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe Minimum weight 40gms complete all as specified and directed.

S & F Vitreous Chine wash down water closet pan single piece with UF seat cover hinges, fixing accessories set, cistern fitting of size 365x655x760 with S trap complete all as specified and directed.

S&F vitreous China wash basin white, flat back size 550x400mm including S&F 32mm dia waste coupling, waste PVC pipe complete all as specified and as directed.

Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float, handle including bracket complete all as specified and directed with glaged finish.

S& F stain less steel decorative cutrain rod of 25 mm bore inluding 2 nos steel finale and bracket 02 nos etc and fixed to wall with plastic rowl plug and steel screw complete all as specified and directed.

S&F 100mm pvc waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors all as completed.

S&F 75mm PVC waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors all as completed.

S&F 75mm bore Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls all as completed.

S&F 75mm bore Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as completed.

M &L for prepepring the entire surface with appliying 2-3 mm thick putty on wall surface internal surface finished even and smooth complete all as specified and directed.

M & L for new plaster surface applying two coat Oil Bound distember on wall surface with roller brush complete all as specified and directed.

M & L for prepring new plaster surface and applying two coat of cement base paint on wall surface complete all as specified and directed.

M & L for new plaster surface applying three coat white wash ceiling surface with roller brush complete all as specified and directed.

M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over pink primer complete all as specified and as directed .

M&L for preparing new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enemal paint complete all as specified and directed.

S&F rotational moulded polythene, triple layers, (white)water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position incl S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed incl Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr complete all as specified and as directed .

M&L for steel work FE-410W as in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. Complete all as specified and directed

Appliying 15 mm thick cement plaster with CM 1:4 smooth with adding 200ml water profing compound at 50 kg of cement finish the surface clean with water at roof complete all as directed by Engr-in-Charge.

M&L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) with 15 cm longitudinal & horizontal over lapping and joints finally pasted with thermo- fused withblow lamp laid over a coat bitumen @ 1.20 Kg /Sqm over bituminous primer 0.30 ltr per sqm as per APP manufacturer instructions etc complete all as specified and as directed. Note :-item includes repair in patches complete all as specified and directed by Engr-in-Charge.

M&L two coat of aluminium paint over top surface of water proofing membrane etc complete all as specified and as directed

Excavation in trenches, n.exc 1.5 m wide and n.exc 1.5 m depth, for foundation, etc. and getting out Soft or loose soil all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exc 25 cm. all as specified and directed.

Removing excavated material N exc 50 m and deposited where directed at a level n.exc 1.5m above the starting point. all as specified and directed.

M &L for Plain cement concrete in foundation filling type D-2 1:4:8 (using 40mm graded aggregate) and mass concrete.

M&L Providing PCC 1:2:4 Type B-1 as in PCC Band,coping etc. all as specified and directed.

M & L for brick work with old size sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius in cement mortar 1:6 all as specified and directed.

M&L for double wall corrugated drain pipes of 150 mm dia bore class SN-8, laid and jointed using rubber ring joints complete with collars etc complete all as specified and as directed.

M&L rendering 15 mm thick in CM 1:4 finished the surface even and smooth without using extra cement with water profing compound.

Supply only liqiued water proofing compound complete all as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required

Providing precast cement concreteRCC 1:2:4 type B-1 but in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces all as specified and directed

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including craking, bending,hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips etc. all as specified and directed.

Surface dressing not exc. 15 cm deep and getting out in any type of soil, complete all as specified

M&L for 75 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

Sand filling under floors or in Foundation including watering & consolidation etc complete all as spd.

M & L for machine pressed coloured rubber moulded precast concrete interlocking paver block with pigment any shape and size confirming to IS-15658-2006 of 60 mm thickness, M-35 grade all as specified and directed by Engineer-in-Charge.

Providing cement concrete Type B-0 (1:2:4), 12.5 mm graded aggregate as in in benching etc complete all as spd and directed .

Dismantling floor, hearth or wall tiling, any type of flooring including wooden and sports flooring including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed

S&F Kiln Seasoned Imported Maple Wood surface board finished with 21 mm thick, 55 to 85 mm width and in random length in tongue and groove shape (The edges of the boards will have a finger lock grove and the bottom side with air pass groove) over commercial quality Fir/Spruce/Pine wood runners of 70 mm X 45 mm treated with anti-termite solution and fixed on the bottom side with 10 mm thick EPDM air cushioning pads by nails through the two wings at 350 mm clc and a total thickness of 76-85 mm including After installation the floor will be machine sanded with floor sander machine and finished with Polyurethane Lacquer. The Game line marking to be carried out in required colors before applying the finish coat. (Note : Rates are inclusive of line marking.)

Providing and laying 10mm thick WOODEN FLOORING, DADO &SKIRTING of Armstrong, Egger or equivalent make (design/color approved by Engineer-In-Charge) consisting of panels of size 1194mm x 194mm or as per manufacturer specification. The panels having a click system tongue and groove joint to secure a long lasting joint with the edges duly impregnated with paraffin. The Floating laminate flooring shall be laid over a 0.20mm thick polythene film to form a vapor barrier and 2mm to 3mm thick approved FOAM The panels used shall be of high solidity, high impact strength, high temperature resistance without change in shape). Each panel shall have click system (tongue and groove profile) and to be laid in approved pattern with suitable glue as per manufacturers specifications including alround suitable egde profile alround/wherever required for firm end locking

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along internal wall using chemical emulsion at the rate of 7.5 litres per sq.m of drilling the floor upto depth of 300mm complete all as specified and directed

E&M ITEMS

Supply, installation & testing of air cooled inverter based split AC unit , Air conditioner is electridriven single phase minimum 5 star rating of capacity 1.5 TR with charged with Eco friendly Refrigerent R410A/R32 and comes with special health filter and all connected accessories and copper tubing from indoor to outdoor with poper nitrile insulation and making of hole in any type of wall, including PVC drain pipe from indoor unit upto plinth protection of building , Outdoor split AC hanging wall mounted stand and flexible PVC pipe minimum 40mm dia covered on all exposed copper insulated pipe line and PVC wire with connected accessories etc all as specified and directed by eng-in-charge.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA .

S&F sheet metal enclosure 20 Amps single pole and natural with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 20 Amp fixed properly in concealed position including making good disturbed surface all as directed by Engineer-in-charge.

Supply, laying in trenches,connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core with suitable clamps for fixing on wall complete all as specified and directed.

Supply, laying in trenches,connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed.

Boring of hole under road/ hard standing by manual means suitable for passing 80 mmGI pipe .

Excavation in trenches not exc. 1.5 m wide and not exc 1.5 mtr deep in soft loose soil for laying / taking up/ taking down of cables and getting out and levelling of bottom suface to required level all as specified and directed by Engineer- in- Charge.

Returning filling in,. Including spreading, levelling,. Watering and well ramming soil in layers not exceeding 25 cm thick all as specified and directed.

Removing excavated material (ie soil) from site to a distance n. exc 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr above the starting point all as specified and directed by Engineer-in-Charge.

Material and labour for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables etc, complete all as specified.

S&F sub class B bricks having minimum compressive strength 75 Kg/ Sqcm laid in trenches for cable protection etc complete all as directed by Engineer-in-Charge.

Supply and installation,testing ,commissioning outdoor type feeder pillar box made out of 3.15 mm thick CRCA sheet, 415 Volt, 3 phase, 50 HZ supply factory made & MS angle section 40 x 40 x 5mm frame with front and back openable double door with provision of locking arrangemnt dust & vamin proof, gasket, Aluminium 400 Amp TP busbar & 600 Amp for neutral shall be insulated with colour costed heat shrinkable sleeves and sahll be mounted on proper insulator, gland, welding hinges of dust proof duly spray painted inside and outside of panel with one coat of red oxide primer and two coat of synthetic enamel paint grey complete all as specified and directed & Connisting of the following equipments:- (i) MCCB, 4 pole, 25 KA, 315 Amp-01 No (Incomming) (ii) MCCB, 4 pole, 25 KA, 125 Amp-04 Nos (iii) MCCB, 4 pole, 16 KA, 63 Amp-02 Nos (iv) Single multifuction meter RE485 Port-6436 -01 Nos, Make- schneider/siemens/socomec) (v) Indication Lamp 22.5 mmm dia LED type 240 Volts AC to show three pahse availablity -01 set (vi) Solid aluminium bus bar 600 Amp for 3 phase, 300 Amp for neutral (vii) Pcc and block Mesonry work for grouting of panel complete all as specified and directed by Engg-in-Charge.

S & F LED street light 35 watt 230 V pressure die cast aluminium housing , heat resistant toughened glass with frame , IP protection IP 66 better optics for uniform distribution having surge protection 10 KV , sealed driver fixed on suitable size medium grade GI pipe bracket with nuts bolts and washers on existing wall Make-Crompton/Phillips /Wipro.

Supply and laying Sub main wiring complete with 03 runs (Phase, Neutral & Earthing colour code) of single core 4 sqmm fire retardant low smoke (FRLS) PVC insulated copper conductor cable multistranded and sheathed LT 1100 V grade drawn through and including non metalic regid PVC medium conduit & conduit 20 mm dia ISI marked and allaccessories including cutting chasing in walls for concealed wiring using mechine and making good the disturbed surface complete all as specified and directed Note :- 2 run of 4 sq mm , 1 run of PVC conduit & 1 run of 4 sqmm cable shall be measured as single unit length.

a)One light/bell point controlled by one switch, with cables 1.5 mm² size

b)One fan point controlled by one switch, with cables 1.5 mm² size

c) One switch socket outlet 3 pin 6 Amp on same board.

d) One switch socket outlet 3 pin 6 Amp on Independant board.

All as per description of serial item No. 126.00 here in before but for for One 3-pin socket outlet 15 Amp on independent board with 2.5 sqmm FRLS cable including 2.5 sqmm FRLS multistranded copper cable as earth continuity wire.

S&F energy saving decorating box type batten light fitting 230 volts surface mounted complete with high effeciency glare free light LED lamp 20 watt blue coloured end caps with all accessories, pre- wired,aluminium housing,polycorbonate difuser integrated heavy duty electronic driver havinng THD < 10% including providing flexible copper wire twin core cable complete all as specified and directed by enginer in charge. Make :- Havells/Crompton/Philips /Wipro

Supply and fix in repair stepped type electronic fan regulator,2 Module white polycarbonate body, flush type, 230 V, including connecting complete all as specified and directed.

S & F modular type 2/3 pin combined shuttered type 6 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

S & F modular type 2/3 pin combined shuttered type 16 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

S & F modular type 6 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

S & F modular type 16 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge

Supply and fix Ceiling rose surface Bakelite 65 x 50 mm three terminals complete all as specified and directed.

supply and fix as in repairs MCB DB single pole and neutral 240 volt SPN 04 way with 200 Amps rated bus bar double door type complete all as specified and directed. Make :- Legrand /L&T/Havells

Supply and fix MCB SPN 10 to 32 Amps 10 KA 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and directed.Make :- Legrand /L&T/Havells

Supply and fix MCB SP 6 to 32 Amps 10 KA 'C' curve 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and directed.Make :- Legrand /L&T/Havells

M&L for earthing complete with GI earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.50 Mtr below ground level. The earth plate to be connetced with earth lead of 4 mm dia galvanised iron or steel wire all as shown in para no 4 the earthing test point all as specified and directd.The GI earthing strip to be protected by galvanised iron pipe 40 mm bore (medium grade) up to ground level and there after with 40mm dia HDPE pipe up to test point. Earthing shall be include with providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) up to 90 cm all around earth plate further filled with 60 cm thick Tibba sand and 2nd layer with 30 cm of Magnesium sulphate powder (compact thickness ) , 3rd layer with tibba sand up to the ground level. Earthing shall also be include for providing concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work all as specified and directed.

S & F modular cover plate with frame, of following modules complete all as specified and directed. Note- Modular switches, sockets & Cover plates with frame shall be of same make & model.

8 Module

6 Module

3 Module

S&F rectangular modular flush mounted Sunken block of following modules suitable for mounting, Modular switches & sockets, complete all as specified and directed.

8 Module

6 Module

3 Module

Please Enable Macros to View BoQ information