SPECIAL REPAIR TO BLDG NO. 62 01 TO 08 QTRS ORs SF Accn AND ALLIED WORKS AT LAXMITEK AREA UNDER GE BELGAUM

Amount

M&L for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete, complete all as specified and as directed.

M&L for Light Shade Coloured Vitrified Ceramic tiles 08mm to 10mm thick (square/rectangular) area of each tile exc. 0.18 Sq.m. but n. exc. 0.36 Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed.

M&L for Light Shade Coloured Vitrified Ceramic tiles 08mm to 10mm thick (square/rectangular) area of each tile exc. 0.18 Sq.m. but n. exc. 0.36 Sq.m, as in skirting / Dado etc., laid over and including 10mm thick screed bed or bedding layer in CM (1:3), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed.

M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exc. 0.06 Sq.m. but n. exc. 0.11Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed.

M&L for Premium quality, joint free ceramic glazed coloured wall tiles of 7 to 8mm thick (square / rectangular) area of each tile not exc 0.18Sqm, on vertical surfaces such as dado and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over & including 10mm thick rendering in CM 1:3 and including taking down existing dado/skirting with backing mortar, complete all as specified.

Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area n. exc 1.5 Sqm each, complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed.

Taking down shutters of any description of area n exc 1sqm each, complete all as specified and as directed.

Taking down shutters of any description of area exc 1sqm but not exc 2sqm each, complete all as specified and as directed.

M&L for Second class hard wood plain solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints , complete all as specified and as directed.

S&F 35mm thick factory made 2nd class hard wood plain, framed, panelled shutters (two panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, size of rail and style as per IS - 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

M&L for Factory made 2nd class hard wood Glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (with divided in to square with plain, chamfered or rounded, mitered and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats, complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window Frame/ Chowkhat of size 45mm x 70mm with virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibbers (wood powder/ rice husk/ wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) with mitre joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant, and fixed in position with and including MS hold fast/lugs/SS dash fasteners as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension rade), calcium carbonate and natural fibbers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, complete all as directed by Engineer-in-Charge.

S&F Factory made powder coated aluminium sliding type window (Triple Track type), fabricated to required size with standard aluminium sections with bottom track of size 92x31.75x1.6mm, side & top frame 92x31.75x1.4mm, top & bottom shutter rail with 39 x 17 x 1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39x27x1.4mm of approved make according to IS (thickness of powder coating not less than 50 micron) including necessary glazing clips, with and including 4mm thick sheet frosted glass for two shutters fixed with rubber gasket and SS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for wire mesh shutter fixed with aluminium beading, anodised aluminium fitting/fixture such as required number of rollers of suitable size, interlocking cleats/plates etc as required, complete all as specified and directed by the Engineer-in-Charge. Note : Quoted rate shall be inclusive of frame, shutter, sheet frosted glass, SS wire mesh and hardware such as butt hinges, tower bolts, handles, locking arrangement etc, complete as required at site.

M&L Framed work such as grills, gratings, rungs etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladder, framed baluster, walk ways, railings, and similar work confirming to Fe-290, Gde E-165, complete all as specified and as directed.

S&F MS butt hinges, cold rolled, medium weight 100mm size, ISI marked, complete all as specified and as directed.

S&F Stainless Steel butt hinges, medium weight, 100mm size, ISI marked, complete all as specified and as directed.

S&F Mild Steel Helical door spring, 300mm long ordinary rat tail pattern spring, ISI marked, including roller and roller plate complete fixed to wooden/steel chowkats complete all as specified and as directed.

S&F IN REPAIR Mild Steel Helical door spring, 300mm long ordinary rat tail pattern spring, ISI marked, including roller and roller plate complete fixed to wooden/steel chowkats complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed.

S&F IN REPAIR Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed.

S&F 150mm long Extruded aluminium alloy 'D' type handles, fabricated type, anodised complete all as specified and as directed.

S&F 125mm long Extruded aluminium alloy 'D' type handles, fabricated type, anodised complete all as specified and as directed.

S&F Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed.

S&F IN REPAIR Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed.

S&F IN REPAIR Brass lock of 50mm for cupboards & drawers, two levers, grade 1, complete all as specified.

S&F Floor door stopper of brass body and tongue,anodised,with 140mm long cover plate and hard drawn steel spring, fixed in door, complete all as specified and as directed.

S&F IN REPAIR Floor door stopper of brass body and tongue,anodised,with 140mm long cover plate and hard drawn steel spring, fixed in door, complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

S&F IN REPAIR Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

S&F IN REPAIR Mild Steel curtain rod, chromium plated, powder coated, fancy type, 25mm bore dia with brackets, fixing stops, roller bracket, wooden nobs etc., with Harrison rails, complete all as specified.

S&F Prelaminated particle board 18mm thick, Interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to cub board shelves / cabinets etc., complete all specifed.

S&F Teak wood lipping of size 18mm wide x 6mm thick, fixed around edges of particle board / plywood with nails, with and including french polishing, complete all as specified.

M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed.

M&L for Rendering 10mm thick on fair faces of new brick work or concrete surfaces of walls in CM 1:6 finished even and fair without using extra cement, complete all as specified and as directed.

M&L for PCC type C1 [1:2:4] (using 20mm graded granite stone aggregate) as in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, finished plain fair faces, including demolition of old cement concrete of any type, complete all as specified and as directed.

M&L for Rendering 5mm thick in CM 1:3 as in ceiling surfaces, finished even and smooth without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even and fair without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed.

M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instructions and finish the surface even and smooth without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed. Note: Supply of WPC will be measured and paid separately.

Supply only Integral Water Proofing Compound. Make: Pidilite Industries Ltd Taloja / FOSROC / Dr Fixit / Asian paints

M&L for preparation of new ceiling surfaces and applying three coats of white wash, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer and 1mm thick wall care putty, complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of new plastered surfaces of any description, all as per manufacturer's instructions, complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including complete removal of existing treatment on wall with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed.

M&L for applying two coats of Oil Bound Distemper over a coat of primer and a layer of 1mm thick wall care putty on walls with and including complete removal of existing treatment on wall with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed.

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for Preparing old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 (using 40mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B2 (using 40mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for rubber coated chequered cement concrete coloured tiles 23-25mm thick, of approved shape and size, as in floor / path, set, jointed and pointed in neat cement slurry with grey cement and pigment, glosy finish on top, laid over and including 15mm thick screed bed in CM 1:4, including demolition of old floor of any thickness, complete all as specified.

M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 mtres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for Factory made Machine pressed pre-cast cement concrete interlocking paver block of any shape and size with glossy finish on top, confirming to IS 15658-2006 of 60mm thick, M-35 grade with grey cement and pigment, with and laid over and including 50mm thick sand cushion (crushed stone sand / M sand) under interlocking paver block including watering and consolidation, with and including dismantling existing stone sett paving of any thickness, removing rubbish off the permises, complete all as specified and as directed.

S&F 20mm outer dia, CPVC pipe SDR 11 with and including all CPVC SDR 11 fittings, fixed to walls/ceilings/ laid in floors, cutting chases as required at site and making good with CM 1:3, including testing, with and including taking down existing u/s GI pipe, complete all as specified and as directed.

S&F 25mm outer dia, CPVC pipe SDR 11 with and including all CPVC SDR 11 fittings, fixed to walls/ceilings/ laid in floors, cutting chases as required at site and making good with CM 1:3, including testing, with and including taking down existing u/s GI pipe, complete all as specified and as directed.

S&F IN REPAIR Bib tap, chromium plated, quarter turn, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed.

S&F IN REPAIR Bib tap, PTMT of any colour, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed.

S&F IN REPAIR Stop Valve, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed.

S&F IN REPAIR 15mm bore chromium plated pillar taps, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F IN REPAIR Vitreous china wash hand basin, Oval Type, white, of size 550x440mm, waste coupling and porcelain stopper including brackets including cutting for and pinning in ends of brackets, 40mm dia CP brass waste fittings, complete all as specified and as directed.

S&F IN REPAIR Vitreous china squatting pan, Orissa pattern size 580mm x 440mm white with integral foot rest including 'P' or 'S' trap etc., with and including cement concrete bedding, complete all as specified and as directed.

S&F IN REPAIR PVC valveless, syphonic action type low level flushing cistern, 10 ltrs capacity, white with inlet ball valve, float and handle soft touch type including brackets, PVC flush pipe, fixed with CP brass screws, complete all as specified and as directed.

S&F IN REPAIR Stainless steel sink of overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, made of 1.0mm thick Stainless steel sheet 304 grade for kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, with and including PVC waste pipe and coupling, complete all as specified and directed.

S&F IN REPAIR PVC Flexible pipe (waste pipe) 32mm bore dia, suitable for 32mm bore waste coupling of sink, WHB, etc., complete all as specified.

S&F IN REPAIR 32mm bore dia Waste coupling of PTMT (half or full threaded) of minimum weight 45gms , suitable for 32mm bore waste pipe of sink / WHB etc., complete all as specified.

S&F IN REPAIR Tubular Towel rail 20mm dia, 600mm long, D type, Brass chromium plated, fixed with CP brass screws, wooden / plastic cleats, completed all as specified.

S&F IN REPAIR Brass shower rose of 15mm inlet and 125mm outlet, chromium plated with swivel joint, CP shower arm 300mm long and CP flange of approved make and quality, fixed to 15mm bore dia pipe, complete all as specified and as directed.

S&F IN REPAIR PVC connections 15 mm size with PTMT nuts 600mm long, completeall as specified and as directed.

S&F IN REPAIR Stainless Steel grating doom 125mm dia (minimum weight 40grams) with / with waste hole, fixed with white cement, complete all as specified and as directed.

S&F IN REPAIR Stainless Steel grating doom 100mm dia (minimum weight 40grams) with / with waste hole, fixed with white cement, complete all as specified and as directed.

S&F IN REPAIR 110mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, fixed to wall with brackets, complete all as specified and as directed.

S&F IN REPAIR 110mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, laid under trenches or laid under floor, complete all as specified and as directed.

S&F IN REPAIR 75mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, fixed to wall with brackets, complete all as specified and as directed.

S&F IN REPAIR 75mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, laid under trenches or laid under floor, complete all as specified and as directed.

S&F uPVC (SWR) bend any radius with access door, suitable for 75mm bore pipes, including jointing with solvent, complete all as specified and as directed.

S&F uPVC (SWR) bend any radius with access door, suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed.

S&F uPVC (SWR) Branch Piece, Single Y, equal or unequal with access door, suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed.

S&F uPVC (SWR) Vent Cowl suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed.

S&F uPVC (SWR) Floor / Nahani trap with grating of 75mm dia outlet, setting and jointing with solvent, complete all as specified and as directed.

M&L PCC 1:5:10 type E2 (using 40mm graded granite stone aggregate) as in foundation, filling and mass concrete etc as in sunken floors, with and including demolition of existing floor, complete all as specified and as directed.

M&L Applying evenly a coat of cold applied bituminous primer @ 1.50Kg/per Sqm and blinding with clean dry sand @ 0.50Cum/Sqm with and including preparation of sunken floor, complete all as specified.

Excavating in post holes (or similar holes), as in hard/dense soil, each not exceeding 0.5cum, getting out , returning ,filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m where directed and making good surfaces, complete all as specified and as directed.

M&L for Moorum/Red bajri filling brought from out side MD land including filling in floors or pavings or in foundations laid in layers n.exc. 15cm thick spread, levelled and rammed including watering, complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

M&L for Hardcore of gauge exc. 63mm but not exc 100mm, broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed.

S&F Rolled mild steel work in tubular trusses, posts, including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to IS-1161:1979 grade St-240, complete all as specified and as directed.

S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle channel or flat sections including distance pieces, cleats etc. conforming to grade Fe 410-W Gde E - 250 quality 'B', complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, with and including taking down existing u/s AC sheet roof of any description, complete all as specified and as directed.

M&L for Mild steel Wind Tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe 290 Gde-E-165, with and including distantling existing steel work of any description, complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete and making good disturbed ground, complete all as specified.

Dismantling ballies, hard or soft wood, any position, except in posts and struts, including taking out iron straps, bolts and nuts, etc., of any type, complete all as specified.

M&L for Bees-wax polishing with machine on kota stone surfaces of any description, width or girth including cleaning and preparing the surface, complete all as specified.

S&F Machine cut cudappah stone slab 20-25mm thick, as in flooring, steps, cooking platform and the like, laid over and including 15mm thick backing coat in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, with and including demolition of existing floor, complete all as specifed and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for complete all as specified and as directed. Note: Quoted rate shall be inclusive of Cutting / separating of reinforcement as required.

S&F Aluminium powder coated frame for doors, partitions, windows and ventilators with one or more rebates of extruded built up standard tubular and other section of approved make, according to IS 1868 (Thickness of powder coating not less than 50 micron) fixed with rawl plugs, screws or fixing with clamps or with expansion hold fasteners including necessary filling up of gaps of junctions at top, bottom and sides with aluminium sections should be smooth, rust free, straight mitred and jointed mechanically wherever required including cleat angle, aluminium anodised screws etc. complete all as specified and as directed.

S&F Minimum 5.0mm thick sheet glass of ordinary quality of approved brand fixed in position with and including PVC/Neoprene gasket for glazing, glazing clips in doors, windows, partitions etc., as in squares exceeding 0.50 Sqm in each pane etc., with all required accessories, complete all as specified and as directed by Engineer-in-charge.

M&L for Pully operated ceiling mounted cloth drying system, with four Numbers of aluminium pipe of outer dia 22mm of each length 1.80m with end caps, pullies made out of delrin with rope guide, mounted with 2 chaneels of 24" inches length fixed to ceiling with self tapping screws, locking arrangement to hide rope knot, rope of polyester braided undyed of 4mm dia and L angle made of 20mm MS square tube of built in system with 4 holes for mounting with nails & holding caps, complete all as per manufracturers instructions.

M&L for water proofing treatment including complete removal of old roof treatment, removal of debris out side MD land and applying new roof treatment consisting of following:- (a) Removing existing plastic felt roof treatment with cement screed, preparation of roof surface by brushing with a neat cement slurry @ 3Kg/SqM and applying 10mm thick plaster with cement mortar (1:3) mixed with WPC @3% by weight of cement. (b) Preparation of roof surface thoroughly cleaning by using wire brush [Mechanical / hand brush] to make it free from any loose particle, dirt / dust, etc. and applying one coat of cold applied bituminous primer @ 0.20 Lit per sq.m. (c) Providing Atactic polypropylene polymeric modified prefabricated water proofing membrane five layered reinforced with non woven polyester matt of minimum 3mm thick weight not less than 3 Kg/Sqm shall be laid using butane torch application over entire roof surface with over laps of 100mm in both the directions. (d) Ponding complete all as specified and as directed by Engineer-In -Charge. (e) Finally roof shall be finished with two coats of bituminous aluminium paint @ 0.10 Kg/Sqm for each coat. Note: WPC shall be measured and paid separately.

Earth work in excavation in trenches or drains (not exceeding 1.5m in width as well as 10Sqm on plan) not exceeding 1.50 m in depth, including dressing of sides and ramming of bottoms, lift upto 1.5m, as in all kind of soil, as in foundation, laying pipe lines / cables etc., complete all as directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D2 (using 40mm graded granite stone aggregate) as in foundation, filling and mass concrete etc., complete all as specified and as directed.

M&L for 150mm dia Reinforced Concrete Pipe NP2, with bends, collars tec., laid in trenches and jointed, with and including cement concrete bed PCC 1:3:6, type C2 (using 40mm graded granite stone aggregate), forming cradles, laid, packing & haunching sides, laid and tested, including dismantling existing sewage line of any description, complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded granite stone aggregate) as in surface channels and drains, complete all as specified and as directed.

M&L for Precast RCC (1:2:4), Type B-1, using 20 mm graded stone aggregate as in precast cover slabs, set in CM 1:4, with necessary formwork of any type, with and including demolition of existing u/s cover slabs of any description, removing rubbish off the permises, complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately.

M&L for Reinforcement TMT bars of Grade Fe–500D upto 10mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded, complete all as specified and as directed.

S&F Mild steel work such as flat iron, angles, etc., as in manhole handles with and including drilling holes etc., cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil, as in any type soil, complete all as specified. [Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.]

Removal of excavated material [Soil] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified.

M&L for Cutting into existing manholes for connecting new drains of internal dia of pipe 200mm bore dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, complete all as specified.

M&L for Reinforced cement concrete 1:2:4 type B-1 (nominal mix) using 20mm graded stone aggregate, as in foundations for drain, including footings, or similar items etc., with and including demolition of existing drain foundation of any type, complete all as specified and as directed.

M&L for Reinforced cement concrete 1:2:4 type B-1 (nominal mix) using 20mm graded stone aggregate, as in drain walls or similar items etc., with and including demolition of existing drain walls of any type, complete all as specified and as directed.

Steel formwork to faces of walls and similar work vertical or to batter for rough finished surfaces of concrete, complete all as specified and as directed.

M&L for 300mm dia Reinforced Concrete Pipe NP2, with bends, collars tec., laid in trenches and jointed, with and including cement concrete bed PCC 1:3:6, type C2 (using 40mm graded granite stone aggregate), forming cradles, laid, packing & haunching sides, laid and tested, including dismantling existing sewage line of any description, complete all as specified and as directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in any type of soil, including removal of the rubish upto 50m, complete all as specified and as directed by the Engineer-in-Charge.

M&L for Point wiring with 1.5 Sq.mm FRLSH PVC insulated unsheathed copper conductor cable, single core multi stranded 1100Volt grade conforming to IS 694: 1977, drawn in and including PVC concealed rigid conduit (minimum 20mm) meadium grade ISI marked, with accessories, junction boxes, tees, terminal boxes with and including factory made metal flush boxes with modular top cover plates with frame for switches / sockets etc., including one run of 1.5 Sq.mm single core FRLS PVC unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly, for one light / fan /bell point controlled by one way switch/MCB, including taking down old u/s point wiring of any type with fittings, complete all as specified and as directed. Note: Cutting chases and making good surfaces shall be included in the unit rate.

All as per Serial Item No. 115 here-in-before but for 3 pin 5/6Amp switch socket point, on same board, complete all as specified.

All as per Serial Item No.115 here-in-before but for 3 pin 5/6Amp switch socket point, on independent board, complete all as specified.

All as per Serial Item No. 115 here-in-before but with 2.5Sqmm copper conductor cable and 2.5 Sqmm cable as earth continuity conductor for 3 pin 6/16Amp switch socket point, on independent board, complete all as specified.

S&F Modular switch 1 way 5/6Amp, 1 Module, 240 Volts, complete all as specified and as directed.

S&F Modular Socket, 5/6A, 2/3 pin combined , 2 module, 240 Volts, complete all as specified and as directed.

S&F Modular switch 1 way 15/16A, 1 Module, 240 Volts, complete all as specified and as directed.

S&F Modular Socket, 6A/16A, 2/3 pin combined multipurpose, 2 module, 240 Volts, complete all as specified and as directed.

S&F Modular Fan regulator, 240Volt, 120 watt electronic step & socket type regulator, 2 Module, for ceiling fan of any sweep, complete all as specified.

S&F Modular Bell push, 5Amp, 230Volt, white, 1 Module, complete all as specified.

S&F Ceiling rose, 3 terminals PVC/Polycarbonate, 3 phase, isolated body, complete all as specified and as directed.

S&F Ding Dong type Calling Bell, 230Volt, AC, complete all as specified.

S&F IN REPAIR LED Industrial Luminaries batten type fitting 1X20watt, 220Volt, >100 lum/W, PF>0.95, AC, integrated type batten, with driver and LED tube light and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified.

S&F IN REPAIR LED Industrial Luminaries batten type fitting 1X10watt, 220Volt, >100 lum/W, PF>0.95, AC, integrated type batten, with driver and LED tube light and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified.

S&F IN REPAIR Lamp holder, PVC/Polycarbonate type with back plate suitable for B22 base with and including 9watt LED Bulb, complete all as specified and as directed.

S&F IN REPAIR LED Building Security light fitting 35Watts, 230 volts, >100lum/W, with Suitable size GI bracket made out of 32mm GI light grade pipe fixed with clamps, nuts&bolts etc., with IP 65/66 protection with LED lamp, driver, bracket with impact, corrosion resistant and all accessories, complete all as specified and as directed.

S&F Ceiling fan complete with blades, down rod, 3 blade type, including electronic regulator step type and accessories, 230Volt, 1200mm sweep, minimum air delivery 210 CFM with service value 6.0BEE, with brushless direct current motor (BLDC), five star rating, including taking down existing u/s ceiling fan and depositing to AGE E/M Store yard, complete all as specified and as directed.

S&F Exhaust fan, steel body, AC single phase, 230Volt, 300mm sweep, heavy duty with blades, frame, louvers, wiremesh with all accessories and necessary fixing details, including taking down existing u/s exhaust fan and depositing to AGE E/M Store yard, complete all as specified and as directed.

S&F IN REPAIR factory made epoxy powder coated distribution board double door TPN 4 ways (VTPN MCCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts and suitable for one FP MCCB 100 Amps as incomer and SP/TP MCBs (or any combination of SP/TP MCBs ) as outgoings, complete all as specified.

S&F IN REPAIR MCCB, 3pole, 125 Amps, 415Volts, thermal magnetic, Ics=100% Icu, 16kA current rating conforming to IEC-60947-II along with spreader incl Phase Barreir to be fixed in distribution board, complete all as specified.

S&F IN REPAIR, Factory made epoxy powder coated sheet metal enclosure for DBs (Fixed flush to the wall), SPN, 415 volt, 8 Way, double door, IP-42 protection with 200 Amp rated copper bus bar 415Volt, and 1.5 Sq. mm copper PVC sheathed cable for earth continuity and suitable for having MCB’s, complete all as specified.

S&F IN REPAIR MCB SPN 40 to 63Amp, 10kA, 230Volt, C curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed.

S&F IN REPAIR MCB SP 10 to 32Amp, 10kA, 230Volt, C curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed.

S&F IN REPAIR Sheet Moulded Compound box of size 250mm x 200mm x 105mm, made out of SMC / FRP with IP 65 protection of thermoplastic circuit breaker boxe suitable for single phase AMR meter, off white colour, with front hinged type door and locking arrangement, fixed on wall with suitable screws, including providing the electrical connection for incoming / outgoing cable through proper lugs/thimbles, complete all as specified and as directed. Make of Box:- Hensel / MECO / Sintex & Make of MCB :Indo Asian/L&T/ABB

M&L for Circuit / Sub main wiring with two runs of 4.0Sqmm PVC FRLSH insulated copper conductor cable, single core multi stranded 1100Volt along with one run of 4.0Sqmm as earth wire, drawn through and including rigid PVC conduit of suitable size (minimum 25mm dia), concealed /surface type, medium grade as per IS 9537 (Part 1-1983) with conduit accessories, including taking down old submain wiring of any type, complete all as specified and as directed. Note: Two runs of cable, one run of earth wire and one run of conduit shall be measured as one unit.

S&F GI pipe light grade pipe 40mm dia for cable protection, complete on pole/walls/in road etc for cable protection, complete all as specified.

Supply, laying, testing and commissioning of LT XLPE insulated, screened with extruded PVC inner sheathed, PVC bedded, galvanised steel strip armoured electric FR power cable [heavy duty] of size 3.5core x 35.0Sqmm, with stranded aluminium conductor, 1100 volts grade, suitable for earthed system with and including cable glands, ferrules and connected accessories, laid in trenches or ducts or through the pipe etc., including taking down old u/s cable, complete all as specified. Note: Necessary excavation & earth work & cable protection pipe shall be measured and paid separately under respective items.

M&L for Dry & clean tibba river sand cushioning in two layers, first layers of 80mm thick before laying of cable and second layer of 150mm thick after laying of cable, levelled and punned down to a depth of 100mm above the top of the upper-most cable, for cable protection in trenches, complete all as specified and as directed. Note: The punned down thickness shall be measured for payment.

Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm, complete all as specified and as directed.

S&F Electric water heater, storage type, SS body with copper inner tank and heating element upto 2 KW, capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pieces and along with inlet & outlet hot water connecting pipes, with and including taking down existing u/s water heater and depositing to AGE E/M Store yard, complete all as specified and as directed. Make : 5 Star rated Monza EC of Havells Code No - GHWAMFSWH025 or equivalent in make specified here in after.

M&L for IN REPAIR Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead 4mm GI wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part-I, including excavation / earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with 8mm dia TMT bars @150mm c/c in bothways, suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 15mm bore GI pipe medium grade for GI wire protection and 4mm GI earth wire, including testing after completion, complete all as specified and directed. Note : Earth wire will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), three layered, 1000 Litres capacity, hoisted and fixed in position all as specified in SSR Part I, with and including 25mm dia PTMT ball valve, including taking down old u/s water tank of any description, complete all as specified and as directed by the Engineer-in-Charge.

S&F IN REPAIR Galvanised steel water tubing 50mm bore dia, medium grade, conforming to IS:1239 (Part I) with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) laid under trenchs and including testing, complete all as specified and as directed.

S&F IN REPAIR Galvanised steel water tubing 25mm bore dia, medium grade, conforming to IS:1239 (Part I) with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) laid under trenchs and including testing, complete all as specified and as directed.

S&F IN REPAIR Gun-metal, globe or gate valves, with iron wheel head, screwed both ends, suitable for iron pipe of 50mm bore, complete all as specified and as directed.

S&F IN REPAIR Gun-metal, globe or gate valves, with iron wheel head, screwed both ends, suitable for iron pipe of 25mm bore, complete all as specified and as directed.

S&F IN REPAIR Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe of 25mm bore dia or brass ferrule and fixed, complete all as specified.

DHAIRYASIL RAMAKANT DESAI (BID ID -3274789)

ASHOK M RAJGOLKAR (BID ID -3274261)

WESTERN DREDGING (BID ID -3275100)

PURVIK CONSTRUCTIONS (BID ID -3274734)

M/S MAHADEV M PATIL (BID ID -3274791)

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS (BID ID -3274685)

SHRIDHAR PATIL (BID ID -3273287)

M/s. VIJAY ELECTRICALS (BID ID -3274652)

M/s. KIRAN M CHOUGULE (BID ID -3273370)

M/s S N Atiwadkar (BID ID -3274243)

ASHIRWAD ELECTRICALS (BID ID -3274519)

M/S JAYDEEP CONSTRUCTION (BID ID -3274204)

M/s.Y.N.PATIL (BID ID -3274563)

M/s. N D KALING (BID ID -3274618)

M/s B C CHOUGULE (BID ID -3274306)