PROVN OF 05X HIGH MAST LIGHTS AT RESIDENTIAL COMPLEX AND ADDN/ALTN OF MT SHED (P/64) AT RMS DHOLPUR UNDER GE BHARATPUR

Amount

PROVN OF 05X HIGH MAST LIGHTS AT RESIDENTIAL COMPLEX AT RMS DHOLPUR UNDER GE BHARATPUR.

Excavation in trenches not exc 1.5 m in depth and not exc 1.5 m wide for taking out/laying/erecting LT pole / LT UG cable, and getting out in soft disintegrated rock / hard / dense soil complete all specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as speified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed

Supply & laying sub class B bricks, locally available of size 230x115x75 mm suitable for LT cable protection cover all as specified and as directed by Engineer-in-Charge

M&L for Dry sand cushioning for protection of under ground cables (8cm before laying the cable and 15cm after laying the cable in trenches) complete all as specified and directed.

M& L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25 mtr below ground level with top edge earth plate at a depth not less than 1.5 mtr below ground level, connected to galvanised earth strip of 32x6mm by means of nuts, bolts, check nuts & washers made of galvanized iron or steel and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1 pre-cast MS sheet cover 30cmx30cmx3.15mm thick with one handle for lifting made out of 8mm dia MS bar, watering pipe 20mm bore galvanized iron pipe (medium grade) with MS funnel for watering charcoal or coke and salt in alternate layers, necessary excavation and earth work in soft disintigrated rock complete all other accessories as shown on electrical plate No 3 of MES Sch Pt-I complete all as specified and directed. Note: (i) Excavation / Earth works and PCC shall be measured and paid separately. (ii) Quoted rate are included of GI strip -32X6 mm with 40 mm GI pipe light grade for protection upto 7.5 M.

Supply and laying 80 mm bore GI tubing light grade socket end laid in trenches or on ground /wall /floor or through pillars where ever directed incl screwed sockets, bends, elbows Short pieces, Connectors, backnuts, diminishing pieces, caps, as as required complete all as specified and directed by Engineer in Charge.

Supply and laying 50mm bore GI tubing, light grade, socket end, laid in trenches or on ground / wall / floor or through pillars where ever directed incl screwed sockets, bends, elbows Short pieces, Connectors, backnuts, diminishing pieces, caps, as as required complete all as specified and directed by Engineer in Charge.

Supply and install commissioning and testing factory made and tested (includng CPRI certified) LT panel box (KIOSK) out door type platform mounted suitable for 415 volt , 3 phase, 4 wire , 50 Hz AC supply system all as specified and directed having busbar chamber with insulated AL bus bars 100 amps rating installed on percelain insulators, the panel shall be dust and vermin proof double door made of 3.15 mm CRCA MS sheet outer & inner 2 mm thick and individual compartment for MCCB/MCB & volt/Amps meter and 40 x 40 x 6 mm thick angle iron for base frame .The complete feeder pillar box should be power coated including internal wiring with PVC insulated solid copper conductor FRLS cables appropriate size but not less than 4 Sqmm. Front opening type with approx for cable entry with double door shutter including locking arrangement as per manufacturers with 2 Keys. The scope of work includes provn of the followings :-

Incoming

(a) Bus bar Al for three phase and Neutral100 Amps Cap - 01set.

(b) MCCB TPN 63 AMP 25KA -01 nos

Outgoing

(a) MCCB TPN 40 AMP 25KA -02 nos

(b) Power contactor suitable for timer switch analog type with time switch

(c) LED indicator lamp -03 Nos

M&L testing and commissionig of High galvanized mast light 20mtr high in two compartment of thickness in lower pole 5mm and top pole thickness 4mm with suitable of air pressure (min) 180 KM / Hr , suitable for 9 lantern symmetrically fitted along with their accessories, clamps etc, and having two point suspension system, with stainless steel wire rope of 6mm dia 97/19 guage and double drum winch with power tools (suitable type three phase motor to up and down of light accessories ) including suitable type copper control cable with industrial type switch and socket as per OEM instruction complete with luminaire mounting arm, pulley assembly, aviation obstruction LED light(2 in one), lightning arrester spike including RCC foundation as per OEM instruction including necessary earth work on Hard /disintegrated rock complete with external control panel as per OEM design suitable for operation (on /off) of High mast light and accessories, aviation obstruction light , lowering and rising (Up and down) of high mast light luminaires (operation of power tools ) with suitable contactor assembly all as specified and as directed. Note :- (i) RCC foundation including TMT bar of suitable sizs as per OEM design with necessary excavation and earth work in Hard / disintegrated rock shall be deemed to included in quoted rate. (ii) control panel outdoor type suitable for on / off of high mast light with timer switch , up and down of light assembly on high mast , control cable from Panel to light complete all as per OEM instruction shall be deemed to included in quoted rate. Make : Bajaj, Philips, Crompton, Utkarsh Tubes and pipe metalcuats.

S&F for LED flood light fitting 250 Watt IP66 made up of pressure dia cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP 66 protection avaliable in NB/MB/WB angels system efficiency =110/125/135LPW.10KV SPD included complete all as specified and directed by Engr-In-Charge

Supply, laying and testing LT UG cable XLPE insulated, screened PVC bedded, galvanised steel stripped or wire armoured electric cable heavy duty with stranded aluminium conductor , 1100V grade of size 35sqmm 3.5 core Sqmm complete all as specified and directed by Engineer in Charge.

Supply, laying and testing LT UG cable XLPE insulated, screened PVC bedded, galvanised steel stripped or wire armoured electric cable heavy duty with stranded aluminium conductor , 1100V grade of size 50sqmm 3.5 core Sqmm complete all as specified and directed by Engineer in Charge.

Supply, laying and testing LT UG cable XLPE insulated, screened, electric cable heavy duty with stranded aluminium conductor , 1100V grade of size 70 sqmm 3.5 core Sqmm complete all as specified and directed by Engineer in Charge.

Supply and install commissioning and testing factory made and tested (includng CPRI certified) LT panel box (KIOSK) out door type platform mounted suitable for 415 volt , 3 phase, 4 wire , 50 Hz AC supply system all as specified and directed having busbar chamber with insulated AL bus bars 200 amps rating installed on percelain insulators, the panel shall be dust and vermin proof double door made of 3.15 mm CRCA MS sheet outer & inner 2 mm thick and individual compartment for MCCB/MCB & volt/Amps meter and 40 x 40 x 6 mm thick angle iron for base frame work.including change over 100amp.The complete feeder pillar box should be power coated including internal wiring with PVC insulated solid copper conductor FRLS cables appropriate size but not less than 4 Sqmm. Front opening type with approx for cable entry with double door shutter including locking arrangement as per manufacturers with 2 Keys. The scope of work includes provn of the followings :-

Incoming

(a) On load Changeover 100 Amp 4 pole suitable for 415 volts-01

(b) MCCB 4 Pole with 25 kA adjustable type - 100 Amps - 01 Nos.

(c) Bus bar Al 4 Pole 200 Amps - 01set.

Outgoing

(a) MCCB TPN 63 AMP 25KA -04 nos

(d) LED indicator lamp -03 Nos

ADDN/ALTN OF MT SHED (P/64) AT RMS DHOLPUR UNDER GE BHARATPUR

Taking down cenment plaster of any description including racking out joints, hacking for kay scrubing down with water etc complete all as specified and as directed.

Taking down shutter exceeding 1 sqm and n.exc 2 sqm each complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) and removing unserviceable material exc 100 mtr complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

S &F for factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification in SSR Part-I complete all as specified and as directed.

S&F butt hinges medium grade cold rolled 100 mm mild steel and fixed complete all as specified and as directed.

S&F mild steel barrel tower bolts 150 mm long, stove enamelled black with bright bolt complete all as specified and as directed.

S&F Mild steel pressed handles oval type size 125 mm, stove enamelled black of all as specified.

S&F mild steel sliding door bolt 250 mm long, plate type stove enamelled black, with bright bolt not less than 12 mm dia with the including a min of 6 bolts and nuts four on bolt plate and two on staple plate complete all as specified and as directed.

M&L glazed ceramic coloured tiles 300 x 450 mm x7mm thick on skirting, dado set and jointed in neat cement slurry and pointed in white cement with pigment to match the surface over 10 mm thick screed in CM 1:4 complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick (square /rectangulament ) area of each tiles exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and as directed.

M&L 15 mm thick for screed bed or bedding layer of CM 1:4 for laying floor finishes complete all as specified and as directed.

S&F as in repair vitreous china squatting pan (Orissa pattern) water closet (white) size 580mmx440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F-2 (using 40 mm graded stone aggregate) as in filling complete all as specified and as directed.

S&F in repair PVC low level flushing cistern 10 ltrs capacity white with inlet ball value, float valve and handle incl brackets, PVC flush pipe complete all as specified and as directed.

S&F in repair vitreous china wash basin white, Ovel type of size 550x400mm including 32mm dia PVC waste pipe CP brass wast coupling 32 mm dia , pair of MS angle brackets or MS fastener/ bolts for fixing arrangements/ granite counter, 450mm long pvc connection with PVC nut and washer complete all as specified and as directed.

S & F in repair vitereous China urinal ,Half stall type white with grating and union for discharge pipe ( excluding flushing cistern flush pipe and waste pipe) complete all as specified and as directed.

S&F Waste pipe 32 mm dia 550mm long PVC for urinal complete all as specified and as directed.

S&F PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and as directed.

S&F in repair Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fency type screwed for iron pipe, suitable for 15 mm bore complete all as specified.

S&F in repair angle valve cast copper chromium plated screwed down, high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type (swan neck ), screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge

S&F in repair stainless steel gratings of outer frame dia 150 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement complete all as specified and as directed.

S&F in repair Soap dish holder (SS), any type, fixed to plugs with screws complete all as specified and as directed.

Takind down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removel complete all as specified and as directed.

S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Dismantling/ disconnecting/ demolition of water storage tank of any type or description and removing from site or refixing in position complete all as specified and as directed.

S & F rotational moulded polythylene water storage tank with 20mm PTMT with epoxy coated Al rod float valve, plastic lid cover, tripled layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs incl making connections complete all as specified and as directed.

S&F in repair 20 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1.3 of girth exe 10 cm in stone, concrete block or slab wall etc complete all as specified and as directed.

S&F PVC SWR bends of 110 mm bore provided with access door complete all as specified and as directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and as directed.

M & L preparation of newly plastered surfaces and applying three coats of white wash in ceiling complete all as specified and as directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron complete all as specified and as directed.

M&L for rendering 15 mm thick on stone masonary surfaces or surfaces other than fair face of brick work or on one side of lathing in cement mortar 1:6, finished even and smooth without using extra cement.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished even and sommoth without using extra cement on edges/ Chajjas/Roof projection and simlar courses etc.complete all as specified and as directed.

M&L rendering 5mm thick in cement mortar 1:3 finished even and smooth without using extra cement on ceilling surfaces complete all as specified and as directed.

M & L preparation of newly plastered surfaces and applying three coats of white wash in ceiling complete all as specified and as directed.

M&L for three coats of white wash on new plastered or unplastered surfaces of walls including prepration of surfaces complete all as specified and as directed.

M&L for 2 coats of cement base painting on newly plastered surfaces of wall incl preparation of surfaces complete all as specified and as directed.

Cutting openings through walls of cement mortar for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for under?pinning including providing,fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning filling including spreading levelling, watering and well ramming in layers n. exc 25cm complete all as specified and as directed.

Removal of excavated soil to a distance n. exc 50m and deposited where directed n. exc 1.5m above the starting point complete all as specified and as directed.

Brick work with sub- class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed.

Surface dressing n exc 15 Cm deep in soft/loose soil complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base, floors and paving complete all as specified and as directed.

M&L 40 mm thick PCC 1:2:4 type B2 using 20mm graded aggregate finished even and smooth as in floor complete all as specified and as directed.

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding,with and including either hooks,and hinges or steel hanging,door fittings (exclusive of steel sheeting or other covering,running rails and guides) and,hanging; also fastening and,fixing complete all as specified and directed by Engr-in- Charge

M&L Mild steel, plain, black sheet 1.00mm thick in hearths; covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed,holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as require complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated etc,) sheets in roof coverings etc complete all as specified and directed.

Excavating in post holes in hard/dense soil n.exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers, n.exc 25cm and making good surface in soft/disintegrated soil complete all as specified and as directed.

M & L for PCC 1:3:6 Type C-2 using 40mm graded stone aggregate as in foundation complete all as specified and as directed.

M&L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc of FE-290 (Gde E-165) (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

Supply and fixing mild steel rolled sections such as angles etc. As in main and cross beam, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding dorrs, fixed with angle cleats or other connected plates confirming to grad FE- 290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in lintels upto 1.5 m clear span and other similar bands, plinth courses, string courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered anglesand throating, complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, molding / folding in circular / semicircular of any position and height fixed with self tapping screwscomplete all as specified and as directed.