REPAIR TO JOINERY CUPBOARD SANITARY FITTINGS FLOORING AND CERTAIN B AND R MAINT WKS IN MD AND OTM ACCN AT DIAT DU AND MILIT GIRINAGAR PUNE 25

Amount

S&F in repairs 25mm dia powder coated aluminium draping rods corrugated of approved quality complete all as specified and directed.

S&F in repairs powder coated aluminium decorative end brackets suitable for 25mm dia pipes complete all as specified and directed.

Complete removal of entire existing water proofing treatment in any position including tarfelt, Plaster/screed bed, lean concrete of any thickness, gravels etc. and removing rubbish the debries out side MD land complete all as specified and directed.

M&L for providing PCC (1:1½:3) type A0 (using 12.5mm graded stone agg) as in padding over roof & chajja (at any respective height of bldg) with using integral water proofing compound as per manufacturer's instructions complete all as specified and directed. Note : Water proofing compound shall be measured & paid for separately as "supply only"

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

Supply only water proofing compound of approved make all as specified and directed.

M&L Acrylic emulsion polymer of acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc complete as per following procedure :- (a) Surface & surface preparation : Remove all the loose particles , dirt & dust clean by water , wire brush & mechanical cleaning , grease & oil should be cleaned using solvents, If the surface is previously coated with tar, it should be thoroughtly scraped off. The surface should be dry before application . All the cracks and crevices in the concrete slab to be filled with polyurethene based sealent with and including application of PU based primer all as directed by Engr-in-Charge. (b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied ,non toxic,VOC complaint)in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers specificationand as dircted by EIC/GE Make:-Bostic,Berger,Fosroc,Sika,Asian,or any other make approved by E-in-C'sBranch for PU based water proofing treatment.

M&L for making hole and fixing the metalic packer for hydrophobic PU foam and sealer without distrubing existing structure as per manufcturers instrction and froming agent like coreseal 357A/ coreseal 357C for carrying out nondistrctive waterproofing treatment of sunkun portion slab, floor and walls of bathroom, WC/WHB and floor traps (Combine Unit) by using construction chemical methods such as hydrophobic PU grouting, epoxy coating etc including cleaning of surfaces with wire brush, detecting the sources of leakage and reapairing, removing/ taking down unsound treatment/ surfaces and followed by material and labour for second course injection of resin like Coreseal 135A/ 135B without distrurbing existing structure complete all as per manufacturers instrctions and as directed by Engr- In- Charge. Make- Buildcore Chemicals/ Pidilite/ Chemistic/ Fosrock or any eqivalent chemicals as approved.

M&L grouting the joints of flooring any type and any size of tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade 0.10 kg of hardener and 0.20 kg of resin per kg, including filling grouting and finishing complete as per direction of Engrineer -in charge.

Dismantling floor or wall tiling including cement mortar bedding ( but not backing) removing serveaceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggre) as in sub base of floor complete all as specified and directed.

M & L for coloured vitrified tiles 9-10mm thick (square/rectangular) of colour and pattern as approved by GE, polished, area of each tile exc. 0.18Sqm but not exc. 0.36 Sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of dark shade tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M & L for coloured non skid ceramic tiles of size 300mm x 300mm x 7mm thick of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar (1:6) as in floors complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles of size 450mm x 300mm x 7mm thick as in dado/ skirting of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

Refixing 20mm dia old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) complete all as directed.

Refixing 15mm dia old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) complete all as directed.

Supply and fix for 15 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fix for 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

S&F for 20mm dia CPVC pipes SDR 11 including all Brass CPVC fittings for 20mm bore pipe on walls/ceiling or laying in floors and including 20 to 15mm dia fittings for fixing of sanitary fittings complete including taking up or down steel tubing and connections or removal to store all as specified & directed.

M&L cutting chases pinning in brick work for concealed water tubing etc. and making good to facings where required and pointing in cement motar 1:3, cutting n.exc. 10cm girth complete all as specified and directed.

Material and labour for PP-R gate valves (brass insert) of 20mm bore complete including taking down old unserviceable valve all as specified and as directed.

S&F in repairs 15 mm bore, 45 cm long PVC connecting pipe fitted with brass unions to connect iron pipe to PVC pipe on both ends complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc.1.5 sqm each complete all as directed.

Taking down shutters of any description, area not exc.1 sqm each complete all as directed.

Taking down shutters of any description, area exc.1 sqm and not exc. 2 sqm each complete all as directed.

S & F for pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames complete all as specified and as directed.

S & F for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames complete all as specified and as directed.

Supply and fix for 30mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35X6mm all around the shutters complete all as specified and as directed.

Supply and fix for 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze,etc.(without sash bars), edges of framing plain,chamfered or rounded, fitted with cut and mitred beads for securing glass,etc; the size of the rail and stile as specified in SSR Part-I, Section 8, clause 8.24 (a) complete all as specified and as directed.

S & F in repair for stainless steel wire cloth 0.63 mm nominal dia of wire, average width of aperture 1.40 mm, fixed with tinned tacks or galvanised wire staples complete all as specified and as directed

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

S & F for factory made solid Panel PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 4mm thick moulded PVC sheet on the front face and 4mm moulded prelam colour PVC sheet on back face wirth wood free EPS, fixed in frame at site as per manufacturer's instructions including fittings complete all as specified and as directed.

S&F in repairs 12mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in cupboard shutters, Kitchen cabinets etc fixed with screw including 3mm thick, 1st class HW(TW) beading all around on edging to timber frame work complete all as specified and directed.

S&F in repair 18mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in cupboard shutters, Kitchen cabinets etc fixed with screw including 3mm thick, 1st class HW(TW) beading all around on edging to timber frame work complete all as specified and directed.

Hacking out old unserviceable glass / broken glass panes of any description, from old wooden or metal frames, or stone, concrete or brick surrounds any thickness or size complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in suitable size for wooden frames in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

All as per item No 39.00 above but Figured glass, pin head type in squares n exc 0.5 sqm each pane complete all as specified and as directed.

S&F 4mm thick plain transperent Fibre glass sheet , pin head type in squares n exc 0.5 sqm each pane complete all as specified and as directed.

S&F steel windows with side hung Double shutters ( one for galzing and other for fly proof shutter) including projecting type hinges with steel handles,steel peg stays complete with glazing bars,and as fly proof shutters complete all as specified and directed.

S&F steel ventilators with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

S& F in repairs 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs 150 mm long aluminium, anodised, or matt finished barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 150 mm size extruded aluminium alloy bow handles, fabricated type with plate, matt or anodised finish complete all as specified and directed.

S & F in repairs for butt hinges, 100mm size, mild steel cold rolled, medium weight complete all as specified and as directed.

Supply and fix in repairs for 75mm size butt hinges, extruded brass with mild steel hinge pin, bright polished and fixed type D-11 complete all as specified and as directed.

Supply and fix in repairs for 300mm, mild steel, ordinary rat tail rod pattern spring (helical spring) including roller and roller plate complete all as specified and as directed.

Supply and fix in repairs for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

Supply and fix in repairs for floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 150mm all as specified and as directed.

M&L for preparation of Interior wall surface,or any waterfall area including removing all fungus, dirt, grease and patches and drying surfaces and filling cracks if any with crack filler and appling two coats antifungal damp proof coating with time difference of min 04 hrs make Asian /Dr Fixit Sure seal or equivalent & approved make, making surface ready to receive final surface finish area and applying two coats 1.50 Sqm per Kg material in horizental and vertical application and as per manufacturer's instructions / specifiaction and directed by EIC.

M & L for preparation of old painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) including necessary scaffolding required for painting work & safety measures at any height of bldg all as specified and directed by Engr-in-Charge.

M & L for preparing old painted surfaces of wood and wood based surfaces of any description over 10 Cm width or girth & applying one coat of synthetic enamel paint all as specified & directed.

M & L for preparation of old distempered surfaces of wall and applying one coat of oil bound distemper etc complete all as specificed and directed.

M&L for preparation of plastered or unplastered old decorated surfaces of ceiling etc. including pillasters and cornices etc. including brooming down of steel wire brushing, scrapping down smoke, soot maoulds mass and efflorescence salts and trading oil and grease spot, washing etc & applying one coat of oil emulsion disteper Complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls/roof projection/chajja including concrete (plastered or un plastered) by brooming down and scraping wherever necessary and applying one coat of external waterproof emulsion paint Apex Ultima or equivalent with primer including necessary scaffolding required for painting work & safety measures at any height of bldg complete all as specified and directed

S & F in repirs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf corner type three tyres with chromium plated brackets, bracket guard and railing 30cm size incl screws, fixed as in repair complete all as specified and directed.

Supply and fix in repair for polycarbonate fibre glass reinforced translucent corrugated/ Plain sheeting 6.00 mm thick hollow section fixed with coach screw and washer in roof, wall etc. complete all as specified and as directed.

Taking down cement plaster on brick/ stone walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement including preparation on old walls to receive new plaster complete all as specified and as directed.

M & L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement including preparation on old walls to receive new plaster complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving n. exe 15 cm thick below or above ground level & removing rubbish/ debries out side MD land complete all as specified and as directed.

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in floors, paving, plinth protection, finished even and smooth without using extra cement complete all as specified and directed .

Material and labour for cast iron Nahani trap, with and including grating of diameter of outlet 75mm including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20mm graded broken stone aggregates) complete all as specified and as directed.

S&F in repair for vitreous China wash basin, white, flat back, size 550x450mm including necessary brackets, CP couplings, PVC waste pipes etc. complete all as specified and directed.

S & F in repairs for vitreous china EWC of white colour with plastic water closet seat cover closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, including connection to drain or out going pipe and to PVC flusing pipe, antisyphonage pipe and all necessary fittings etc complete all as specified and as directed.

S&F in repairs plastic water closet seat cover, white closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs 10 liters capacity PVC low level flushing cistern with ISI marked body, fixed in repairs complete all as specified and directed.

S & F in repairs for 15mm dia PVC connection 450mm long including PTMT check nuts etc complete all as specified and as directed.

S & F in repairs chromium plated faucet health (hand jet) 15mm bore with fittings, and including two way bib tap and accessories complete all as specified and directed.

S&F in repairs stainless steel grating doom 100 mm dia complete all as specified & directed.

S&F in repairs Chromium Plated Toilet Roll Paper Holder with stainless steel flap complete all as specified and directed.

S & F in repairs soap dish chromium plated of size 100 x 100 mm any type, chromium plated brass screws complete all as specified.

S & F in repairs kitchen sink waste couplings size required at site etc. complete all as specified and directed by EIC.

S & F in repairs hand wash basion waste couplings size required at site etc. complete all as specified and directed by Engr-in -charge.

S&F in repairs 15 mm dia PTMT ball valve, high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repairs 20 mm dia PTMT ball valve, high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union complete all as specified and directed.

S & F in repair for 15 mm bore bib taps chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

S & F in repairs 15 mm bore pillar tap CP fancy type complete all as specified and as directed.

S & F in repair for 15 mm bore chromium plated, mixer for mixing hot and cold water screwed down for iron pipe including wall flanges complete all as specified and as directed.

S & F in repairs for CP 15mm dia stop cock(Concealed) with long shank and cup complete all as specified and as directed.

S & F in repairs for 15mm dia CP bib tap long body with flange complete all as specified and as directed.

S & F in repairs spindel of brass of any size/ type and in any position complete all as specified & directed.

S&F in repairs low density polyethylene(LDPE) pipes for working pressure rating 6 Kgf / Sqcm with polyethylene thread union and check nuts for waste pipe of WHB, 750 mm long, 32 mm dia complete all as specified and directed.

S&F in repairs 40 mm dia, 75 cm long PVC low density waste pipe for stainless steel sink of working pressure rating @ 4 Kg / Sqcm with polyethylene union and check nuts complete all as specified and directed.

Welding in repairs n.exc. 2.5 cm in length and thickness of metal/steel to be welded n.exc. 6mm complete all as specified and as directed.

Supply & fixing PVC bath cabinet, size 450 x 600mm, comprising of looking glass, space for bath soaps, shampoo, tooth brush and paste, handle towel rail, fixed as in repairs complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

All as per item no 91.00 above but 110mm dia including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along along the centre line over fittings and accessories) complete all as specified and as directed.

M&L for PVC (SWR) bends of any radius with oval and access door of 75mm dia complete all as specified and as directed.

All as per Srl item No 93.00 above but 100 mm dia complete all as specified and as directed.

Dismantling of stone slabs, cudappah, of any description or thickness in floor/fixed to walls, apron etc laid bedded and pointed in cement mortar complete all as specified.

M&L machine cut Granite slab 18 mm thick as in steps, pillars, window cills, cooking plateforms and like and incl 10mm thick (avg thickness) cement mortar 1:4 screeding and setting coat in cement morter 1:2:3mm thick, set and jointed with white cement sturry mixed with pigment to match the shade of slab incl cutting, waste, rubbing and polshing etc complete all as specified and directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish complete all as specified and directed.

Labour only for full round moulding to 18 to 20mm thick granite slab complete all as specified & directed.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 15 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repairs stainless steel plate rack, made out of 1.00mm thick sheet of size 75 cm x 75 cm fixed as in repairs complete all as specified and directed.

J D Contruction

OM GANESH CONSTRUCTION

J.G.Goel