Construction of demonstration building at CSIR-CEERI Pilani

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead within CEERI campus as per direction of Engineer In Charge.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering,lead within CEERI campus and for all lift

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering - All work up to plinth level

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Stairs, (excluding landings) except spiral-staircases

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. including dismantling of existing kota stone slab with mortar and preparation of surface etc complete

Granite stone slab of all colour and texture Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Providing and fixing Ist quality ceramic glazed wall tiles (Size not less than 300 mm x 450 mm) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades (light,dark and designer etc ) of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand),having below rough plaster of average 20 mm of 1:4 ( cement :4 coarse sand) for surface preparation and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing aluminium body Cam Action Slide Channel Overhead hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment and 90 degree stop arrangement, of approved quality and make with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Size 250x10 mm

Size 100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Size 125 mm

Providing and fixing bright SS finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of strainless steel 304 lever handles of approved quality and make with necessary screws etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Hot finished welded type tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Plate in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete

Providing and laying vitrified floor tiles with spacer in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Glazed Vitrified tiles Matt/Antiskid finish of size 600x600 mm

Providing and laying Vitrified tiles in different sizes with spacer (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Glazed Vitrified tiles Matt/Antiskid finish of size 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Size of Tile 600x600 mm

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

12 mm cement plaster of mix : including proper double scoffolding system

1:4 (1 cement: 4 coarse sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade including proper double scoffolding system

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing bright finished SS304 hard drawn hooks and eyes :

Size 150 mm

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe and cp health facuet, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets and dash fastner, 15 mm C.P. brass pillar cock , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :

White Vitreous China Wash basin size 550x400 mm with C.P. brass pillar basin mixer with central hole and long braided hoses

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe 32 mm dia

Providing and fixing mirror of size 600x450 mm superior glass (of approved quality) and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing, fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soil, waste and vent pipes :

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

75 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

75 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree.

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

75 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing terminal guard

100 mm Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe

100 mm dia SS 304 grade coupling with EPDM rubber gasket

75 mm dia SS 304 grade coupling with EPDM rubber gasket

Providing and fixing Steel finished clamps with base holder plate with accessories etc complete for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :

100 mm dia

75 mm dia

Providing and fixing P-trap / Floor trap of self cleansing design with screwed down or CP hinged grating with frame with or without hole, vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

100 mm inlet and 75 mm outlet Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls and floor etc. Internal work - Exposed on wall including synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling ,including painting with anti corrosive bitumastic paint and connection with main linewith fillings etc complete

20 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall

15 mm dia nominal bore

Providing and fixing uplasticised PVC connection pipe in SS finish with brass unions :

45 cm length & 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

15 mm nominal bore

20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water torage tank,IS: 12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes with 03 nos tank nipples and the base suppport for tank & including providing and fixing 20mm dia ball valve (brass) of approved quality, High or low pressure, with plastic floats complete for each tank.including taking down existing pvc tank & deposited in store yard as per direction of Engineer in-Charge.

Providing and fixing C.P. brass bib cock with wall flange of approved quality conforming to IS:8931 as per direction by Engineer in charge.

15mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 with wall flange as per direction by Engineer in charge

15mm nominal bore.

Cutting holes up to 30x30 cm in walls including making good the same:

with common burnt clay F.P.S. (non modular) bricks

Providing,laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints including trenching , refilling and dismalting of existing old SW pipe etc.complete :

100 mm diameter S.W.pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

100 mm diameter S.W.pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight FRP/GRP cover with frame of 300 x300 mm size (inside) the load capacity of cover to be not less than 12.5T as per standard design:

150 x 100 mm size P type without common burnt clay F.P.S (non modular ) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing strainless steel hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge

Powder coated minimum thickness 50 micron aluminium

Grading roof for water proofing treatment with

Cement mortar 1:4 (1cement : 4 coarse sand)

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above.

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).

Cellular Light Weight Block (Size: 300X150X150)mm Masonry of M10 Grade in super structure above plinth level up to floor V level in:Cement mortar 1:4 (1 cement : 4 coarse sand).

Providing and Fixing 0.50 mm thick PVDF (Poly Vinylidene fluouride) both side of aluminium thickness 3.00 mm overall thickness 4.00 mm on walls,in doors & ceiling with proper required haging system and having fire rating of 120 minutes and fixing with silicon tape/ adhessive material as required ,in opening shutters and fixed sections including cutting PVDF sheet as per required at site, preparing smooth surface and making holes/making good as required cutting hoisting and fixing aluminium members etc. complete as directed by Engineer-In-Charge

Part 'B' Electrical Work - Point Wiring :- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C (Irrespective of any length)

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed steel conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base, cover & blanking plate for modular switches in recess etc. as required. etc as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections butexcluding modular plate etc. as required.

Telephone socket outlet RJ 11

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3pin, 6 amps modular socket outlet with 1 No. 16 amp moduler switch and 1No. 6 pin 5/6 & 15/16 amps modular socket with 1no 16 amp moduler switch, blanking ,connection, painting etc. as required (different in colour of cover plate from general power for UPS / computer applications), making good the wall with matching colour distemper/ white wash etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch/removing recessed existing board, disconnection making connections and testing etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

2 x 1.5 Sq. mm

Telephone & Data : Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying & Fixing of following sizes of steel conduit along with heavy duty accessories, junction box etc. in surface / recesse including painting in case of surface conduit, or cutting the wall, repair and making good the same as required.

Supplying and drawing of 23 AWG UTP Data Cable (CAT 6) gigaspeed LAN Cable in the existing surface/ recessed Steel/ under floor trunking as required.

1 run of cable

P & F following modular accessories made out of unbreakable and fire retardant poly carbonate with silver contacts Simplex Faceplate with RJ-45, information outlet with shutter with colour coding on existing modular plate, including making connections testing etc. as required

Supplying and fixing 6-10 amp 'C' Curve modular DP MCB on the existing modular plate including connections but excluding modular plate etc. as required.

Light and Fan :- Supplying of Surface / Ceiling mounted LED 18 watt light fixture- Circuler light Surface Light, 6500 K with housing approved make including, connection wire of suitable length, all accessories etc. as required.

Supplying of recessed mounted 35 Watt full glow, slim energy efficient, Green Square 2'x2' LED lighting luminaires, with Luminous Flux 4200 lm, approved make complete with hanging arrengment all accessories, metallic CRCA powder coated housing etc. complete as required.

Installation, testing and commissioning of above LED tube light fittings complete with all accessories on surface of wall/ ceiling or suspended from ceiling including providing hanging arrangment with clutch wire, transperent connection wire/ 1.5Sq.mm FR PVC copper conductor etc. as required.

P/ F IP-65/66 30 watt protected LED street light luminaries of following sizes on existing bracket. Fixture made from powder coated single piece pressure die cast aluminum housing with heat dissipation fins on housing with high power LED lights and driver should have minimum 2 year warranty. Diffuser / glass cover for ensuring IP-65 protection for lamp and control gear compartment, Integrated driver having efficiency more than 85 % and in compliance to IEC standards etc. as required. approved make.

Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of LED / HPMV / HPSV street light fitting on wall/ pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

Supply of following sizes of BLDC energy saver ( 5 star rated) ceiling fan without regulator complete with double ball bearing, motor, blades, down rod, canopy, etc. complete as required.

Size 1200 mm.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of length upto 30 cm with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. complete as required.

Cables:- Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supply of XLPE insulated PVC sheathed 1.1 kv. Grade copper/Al. conductor armoured Cable IS: 7098 Part-1 of approved make.

4 X 50 Sqmm Al. Cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.

Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade on wall/ roof/ duct/ shaft including fixing by means of screws & rag bolts, suitable size MS U clamps complete as per specifications, repairing works etc as reqd. of following sizes of cables.

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp

Supply& making one end termination with heavy duty single compression brass gland SIBG type, aluminium/ copper lugs duly crimped with crimping tool, PVC tape etc. for following size of XLPE insulated & PVC sheathed aluminium/ copper cable of 1.1 KV grade as required.

4 X 50 Sqmm

P & F Recessed/ surface mounting vertical type heavy duty Double door type TPN-4 way sheet steel phosphatised powder painted Distribution Board with incomer 1No. MCCB-125A, 16KA and 4 Nos. TP AC MCB-63A 10KA ( 'C' breaking characteristic) for outgoing circuits, 200Amp busbar, neutral link, earth bar & din rail etc conforming to IS; 13032, IS; 8623, BS; 5486 of approved make including making all the incoming/ outgoing connections, internal DB terminations with copper lugs, testing etc. as required.

P & F Recessed/ surface mounting vertical type heavy duty Double door type TPN-4 way sheet steel phosphatised powder painted Distribution Board with incomer 1No. MCCB-125A, 16KA and 12 Nos. SP AC MCB-16-32A 10KA ( 'C' breaking characteristic) for outgoing circuits, 200Amp busbar, neutral link, earth bar & din rail etc conforming to IS; 13032, IS; 8623, BS; 5486 of approved make including making all the incoming/ outgoing connections, internal DB terminations with copper lugs, testing etc. as required.

SITC of MCCB in CRCA sheet steel enclosure complete with four pole Moulded Case Circuit Breaker (Ics Value 18KA), Adjustable Thermal & Fixed Magnetic setting, suitable for incoming & outgoing termination including powder coating etc. complete as per specification & as required.

125 Amp FP MCCB.

Supplying and fixing of ,4 Way three pole and neutral, prewired, sheet steel, per phase isolation ( PPI ) MCB distribution board, 415 volts on surface / recess, complete with loose wire box, Incomer 1No. 40A, 4 Pole isolator, Outgoings- 3Nos. DP RCCB 40A, 240 volts, having a sensitivity current 30 milliamperes, 12 Nos. SP AC MCB-32A, 10KA, 240V ( 'C' curve ), terminal blocks, duly prewired with suitable size FRLS PVC insulated copper conductor upto terminal blocks, tinned copper bus bar, seperate neutral links for each phase, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted, making internal DB terminations with copper lugs including all the existing incoming/ outgoing connections, earthing, testing, repair & making good the wall with matching colour distemper/ white wash etc. as required.

P & F of heavy duty capacitor start Exhaust fan Size-300 mm sweep, 900 RPM, single phase, IS: 2312 marked of Havells make model-Turbo force SP or other approved make in existing opening including grouting of metal fastener with bolts, nuts making connections , testing etc. as reqd.

P & F of gravity louver shutter of superior quality made out of frame of 18 SWG MS sheet & louvers made from 24 swg Al. sheet with nut bolts enamel paint etc as required. Size Up to 380mm. ( for 200 mm and 300mm Exhaust Fan)

DEVENDRA KUMAR (BID ID -839226)

jagdamba builders (BID ID -841098)