PROVISION OF GUARD ROOM TOILET BLOCKS TO TB I COVERED URINAL POINT TO PCTC TRG AREA AND SPECIAL REPAIR TO BLDGS NO T 43 UNDER GE NORTH BANGALORE

Amount

B/R WORKS

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating in trenches n exc. 1.50 m wide and n.exc. 1.5 m in depth for foundation and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling in excavated soil, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in hard / dense soil etc complete as specified as directed.

Removing excavating material n.exc 50 m and despositing where directed at a level n.exc 1.5 m above the starting point.

Anti termite treatment to the bottom and sides of excavation at the rate of 5 litres of emulsion per sqm of surface area etc complete as specified as directed.

Anti termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per sqm of vertical surface (area of sub structure in contact with back fill to be measured) complete as specified as directed.

Anti termite treatmentto the the top surface of filled earth at the rate of 5 litres of emulsion per sqm of surface area complete as specified as directed.

Anti termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per sqm of surface area complete as specified as directed.

Anti termite treatment to the soil along with external perimeter of buildings at the rate of 2.25 litres of emulsion per meter of the perimter wall complete as specified as directed.

Plain Cement Concrete as in foundation filling and mass concrete (1:4:8), type D-2, using 40 mm graded stone aggregate complete all as specified and as directed.

Reinforced Cement Concrete, M-25(design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc basement slabs, under reamed piles and mass concrete complete all as specified and directed.

Reinforced Cement Concrete, M-25(design mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

Reinforced Cement Concrete, M-25(design mix) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Reinforced Cement Concrete, M-25(design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter etc rough finished the concrete surfaces in flat complete all as specified and directed

Steel formwork to sides of pillars, posts, struts, piers, columns and stanchions etc rough finished the concrete surface complete all as specified and directed

Steel form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc rough finished the concrete surface in flat complete all as specified and directed

Steel form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (horizontal or sloping) etc, rough finished the concrete surface complete all as specified and directed

TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending etc and securing with including Mild steel wire (annealed) not less than 0.9mm dia.

TMT steel bars 8mm dia, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

TMT bars 8mm dia and over cut to length, bent to shape required, including cranking, bending etc and securing with including mild steel wire (annealed) not less than 0.9mm dia as in stirrups spacers and binders complete all as specified and directed.

Plain Cement Concrete,(1:2:4), type B0, 25mm thick as in damp proof course using with and including supply of approved integral liquid water proofing compound as per manufacturers instructions complete all as specified and as directed.

Precast cement concrete block masonry with solid blocks exc. 10 cm in width and setting in cement mortar 1:6 type C1 1:3:6 (using 20 mm graded aggregate) complete all as specified and as directed.

15mm thick rendering on brick or concrete surface in cement mortar (1:6) and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick consisting of two coats of 5mm thick in CM(1:4) over a coat of 10 mm thick in CM(1:6) mixed with water proofing compound as per manufacturers instructions finishing the surfaces even and smooth without using extra cement including necessary scaffolding complete all as specified and directed. NOTE:- WPC will be measured and paid separately under relevant items.

Rendering 5 mm thick on ceiling / RCC surfaces in cement mortar (1:3), finishing the plastered surfaces even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound emulsion distemper over a coat of alkali reistant primer on walls over two coats of wall care putty complete all as specified and directed

All as per Sl Item No. 1.027 above but in ceiling surfaces.

Preparation of newly plastered wall surfaces of any description including brooming down with steel wire brushing, scrapping down smoke soot's , moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint (Apex Ultima or equivalent brand as specified in CA) over a coat of weather proof primer including filling the cracks etc with crack filling material all as per manufacturers instructions complete all as specified and as directed.

Supply only integral liquide water proofing compound all as specified and as directed.

Preparing the new RCC surfaces and providing screed bed/rendering 10mm thick in CM (1:4) mixed with and including supply of approved water proofing compound as per manufacturers instructions by removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and providing 50mm x 50mm coving at the corners with PMC mortar as above, and applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017 mineral finish, 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed.

Hard core of guage n.exc. 63mm deposited spread and levelled, laid in layers n.exc. 15cm thick, watered and rammed to a true surface using broken boulders all as specified and as directed.

Plain Cement Concrete (1:4:8), type D-2 using 40mm graded stone aggregate as in sub base to floors, 75mm thick complete all as specified and as directed.

Plain Cement Concrete, (1:3:6), type C-1 using 20 mm graded crushed stone aggregate,) 75mm thick as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) finished the concrete surface even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed.

Plain Cement Concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in floors 25mm thick, as in sub base to floor complete all as specified and as directed.

Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

Glazed ceramic tiles in vertical surfaces 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over rendering 10mm thick in CM(1:4) on fair faces of brick work or concrete surfaces to receive wall tiles complete all as specified and as directed.

Matt finish coloured ceramic tiles 9-10mm thick 600x600mm rectified digital floor tiles as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in CM(1:6) complete all as specified and directed Make : Satin series of kajaria or equivalent of somany/Navin/Jhonson

All as per Sl Item No. 1.038 above but in skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM (1:4) on brick or concrete surfaces finished rough to receive wall tiles complete all as specified and directed.

Chequerred cement concrete tiles 300x300x25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigments to match the colour of tiles over 20mm thick screed bed in CM (1:4) complete all as specified and directed.

Factory made pressed steel frames of size 125 x 60mm for doors with one or more rebates(02 rebates) including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and as directed.

Factory made flush door shutters 35mm thick, as per IS:2202 (Part-I 1999) solid core construction, with block board core and plywood face panels, commercial type on both sides including providing teak wood beading as per drawing and painted to match the door fixed to chowkhats all as speified and as directed.

Box type Steel Windows / ventilators double side shutters (windows side hung type, ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm, windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars/grill welded with steel frame (100c/c horizontically) all as specified and directed by Engineer-in-Charge. Condt/--- 1.044

Condt/--- 1.043 NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bard/Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges, telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only 4 mm thick sheet glass and stainless steel wire mesh be measured and paid separately. (iii) Weight of Grill/Guard Bars, handle,hinges and locking arrangements shall be deemed to be included in the quoted rate. (Note : All Windows/Vent design as per CECZ TD drg No 539)

Galvanized mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed with tinned tack or galvanized wire staple fixed with beads all as specified and as directed.

Plain sheet glass 4mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane and all as specified and as directed.

Rolled MIld steel framed work as in doors or gates of angle or other sections with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging ; also fastening and fixing complete including painted with one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop/factory before fabrication complete all as specied and directed.

Plain Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in copings, bed blocks, hold fasts, steel frame of window back filling and in roof kerbs of mud stops, rounded or chamfered on edges cills, steps etc complete all as specified and directed.

Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

Aluminium anodised barrel tower bolt of extruded section of size 200mm long complete all as specified and as directed.

300mm long Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Extruded Aluminum handles 150mm size, fabricated type, anodised all as specified and as directed.

150 mm long floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

Magnet door catcher made out of stainless steel complete all as specified and directed.

Rubber door buffer 125mm size fixed with brass screws complete all as specified and directed

Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed to steel door complete all as specified and directed

Mild Steel pressed handles oval type stove enameled black 150mm size complete all as specified and as directed.

Mild steel 300mm long, ordinary rat tail rod pattern springs,including roller and roller plate complete all as specified and as directed.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, including making good to jambs with cement mortar (1:4) and finished to match with existing surface complete all as specified and directed.

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawings.

PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified and as directed.

PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified and as directed.

PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and as directed.

Anodised aluminum powder coated (of any shade/colour as approved by GE) ventilators with adjustable 4mm thick figured glass louvers, fixed in qtr portion, without sash bars, aluminum section weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, including stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.18mm including complete etc all as specified and directed by the Engineer-in-charge (size of ventilators = 600 x 900 mm)

Rolled Mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel over a coat of red oxide primer, complete all as specified and directed.

Preparation of new or previously untreated wood or wood based surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer on wood or wood based material over 10 cm width or girth all as specified and directed.

Drapery rod of high strength aluminum rod powder coated thickness 40-60 micron of outer dia 28mm & inner dia 24.5mm with providing 2 Nos brackets(projected type/wall to wall) and fineals all as approved by GE, as specified and as directed. (Make : MAC-Sleek line type II/ Vista Levolor Soffio-II)

Vitreous china wash down water closet pan (pedestal pan) including fixing bolts, flush pipe anti syphonage pipe, including plastic EWC seat cover, coloured closed pattern with flat bottom and cover mild steel chromium plated or aluminised hinging device complete all as specified and directed

PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and directed.

Vitreous china wash basin, white flat back of size 550x400mm excluding chain, plug and porcelain stopper but incl CI bracket. waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe 75 cm long complete all as specified and directed.

Urinal flat back of size 465x365x265 mm white with grating and union for discharge pipe including connection to flushing pipe and waste pipe complete all as specified and as directed.

20mm dia GI tubing medium grade and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

16mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs capacity complete complete all as specified and as directed.

Gun metal gate or globe valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as per Prayag cat No-PIS-75H or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Brass chromium plated over head shower rose 100 mm size with or without swivel joints, any size, including fixing to steel pipe or union all as per Prayag cat No-BOS-86 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

15 mm dia pillar taps swan neck type, chromium plated cast copper alloy fancy type all as per Prayag cat No-PIS-14H or techno commercially equivalent makes specified in PS complete all as specified and as directed.

15mm dia angle cock chromium plated cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc.,all as per Prayag cat No-PIS-10H or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Bib Cock 2 way double handle with CP flange all as per Prayag cat No-PIS-12H or techno commercially equivalent makes specified in PS complete all as specified and as directed.all as specified and as directed.

Health faucet, brass body with 1mtr SS braided tube & wall hook all as per Prayag cat No-BEA-41/BEA-85 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Towel rail stainless steel glossy finish all as per Prayag cat No-BA10S or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Looking mirror of size 600x450 x5-6mm with frame all as per Prayag cat No-BLM-01F or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats ,minimum weight 300gms complete all as specified and as directed.

Peg set of six fixed in walls as per manufacturers instructions all as per Prayag cat No- BEA 30 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

PVC connections 15mm dia with PTMT nuts of length of 600 mm long complete all as specfied and as directed.

PVC corrugated waste pipe 32mm dia, 800mm long complete all as specified and as directed.

75mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed.

Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to walls / floors including PVC clamps and necessary fittings complete all as specified and as directed.

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to walls / floors including PVC clamps and necessary fittings complete all as specified and as directed.

200 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches and necessary fittings complete all as specified and as directed.

Plain Cement Concrete, (1:4:8), type D2 using 40 mm graded stone aggregate as in bed to drain pipes i including packing under and haunching against the sides of pipes after they are laid and tested suitable for 200mm dia bore pipe complete all as specified and as directed.

75mm bore PVC (SWR) bends with access door, type 'B' complete all as specified and as directed.

110mm bore PVC (SWR) bends with access door, type 'B' complete all as specified and as directed.

75mm bore PVC (SWR) junction single (single T), type 'B' equal or unequal with access door complete all as specified and as directed.

110mm bore PVC (SWR) junction single (single T), type 'B' equal or unequal with access door complete all as specified and as directed.

110 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door complete all as specified and as directed.

75 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door complete all as specified and as directed.

110 mm bore PVC (SWR) branch piece (double Y), type 'B' equal or unequal with access door complete all as specified and as directed.

75mm bore PVC (SWR) branch piece (double Y), type 'B' equal or unequal with access door complete all as specified and as directed.

PVC (SWR) vent cowl of bore 75 mm dia, type 'B' complete all as specified and as directed.

PVC (SWR) vent cowl of bore 110mm dia, type 'B' complete all as specified and as directed.

Extra for forming fair finished surfaces of drain or channel 30 cm inner girth in cement concrete using extra cement all as specified and as directed.

Precast Reinforced Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in cover slabs of man hole set in CM (1:4) complete all as specified and as directed.

On site LLDPE septic tank designed suitable for 05 users to carry sewage and sullage water including excavation in any type of soil, over PCC (1:4:8 ) foundation, vent shaft, connections etc., complete all as specified and as directed.

Plain Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in coping and haunching of man holes etc., complete all as specified and directed.

Brass chromium plated fancy type stop valves 15mm dia screwed down,screwed for iron pipe complete all as specified and as directed.

25mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

20mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

Precast Cement Concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type B1 (1:2:4) using 20mm graded stone aggregate as in walls in width and setting in cement mortar (1:6) complete all as specified and as directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches with necessary fittings complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer all as specified and as directed.

Prepartation of new or previously un treated ceiling surfaces of any description and applying three coats white wash complete all as specified and as directed.

Prepartation of new or previously un treated wall surfaces of any description and applying three coats white wash complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 2000 ltrs capacity complete complete all as specified and as directed.

20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed(Min weight 20mm-210 gms) all as specified and as directed.

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Mild Steel ventilators with top hung shutter(half fixed) including hinges, steel peg stay, complete with glazing bars and 10 x 10 mm square guard bars in equal spacing, devoited or welded including one coat of red oxide primer all as specified and directed. NOTE :- PCC in frame, glass pane and wire mesh shall be paid separately under relevant items.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe complete all as specified and directed.

PVC (SWR) gully trap 125/110mm setting and jointing in solvent cement complete all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches with necessary fittings complete all as specified and as directed.

PVC (SWR) multi floor trap 110mm dia type 'B' with grating including joint with solvent cement complete all as specified and directed.

Bib taps standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia fixed complete all as specified and as directed.

Stop cocks standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia fixed complete all as specified and as directed.

Cutting into existing manholes for connecting new drains by cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete (1:2:4)type B-1 smooth finishing & making good to pipe as per existing by rendering & reforming benching as required for 150mm bore pipe complete all as specified and directed.

3 mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with MS screw & bolts in repairs all as specified and as directed.

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) all as directed.

Demolition of brick work or stone / PCC /boulder masonry built in cement mortar or lime mortar including all quions, arches, pillars but excluding ashlar facing, dressed stone work of any description all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key and disposing of debris to a distance exc 1 Km out side MD land complete all as specified and directed.

Dismantling of AC Sheets of any description as in roof covering including ridge, wind tie etc., complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Taking down chowkat (without taking of shutter from the frame) area not exc. 1.5 sqm each including making good the disturbed surface in PCC(1:2:4) type B0 or CM (1:3) all as specified complete all as specified and directed.

Taking down chowkat (without taking of shutter from the frame) area exc. 1.5 sqm and n.exc. 4 sqm each including making good the disturbed surface in PCC (1:2:4) type B0 or CM (1:3) and all as specified and as directed.

Brick work with sub class 'B' bricks built in CM(1:6), straight or curved on plan exc 6 mtr mean radius, using old size bricks complete all as specified and as directed.

Brick work (except bricks)with sub class 'B' bricks built in CM(1:6), straight or curved on plan exc 6 mtr mean radius, using old size bricks complete all as specified and as directed.

Rolled mild steel in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plates of Fe-410W (Gde E-250) complete all as specified and directed.

All as per Sl Item No 1.141 above but erection and fixing only.

Rolled Mild steel work as in hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and counter shunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specifed and as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tenisile strenth of 550 Mpa as in roof covering cladding to wall, pre fixed with self taping screwes as specified and as directed.

Galvanized mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed with tinned tack or galvanized wire staple fixed in repairs with beads all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from metal / wooden frame works or stone / concrete/ brick surrounds including punching or drilling out old glazing pins/spring clips or fixed with wooden beading etc complete all as specified and as directed.

Machine cut Kota stone slab flooring 18-20mm thick, mirror polished homogeneous colour laid over 20mm thick screed bed in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Machine cut Kota stone slab 18-20mm thick as in skirtings / risers, mirror polished homogeneous colour, fixed over and including 10mm thick backing coat in CM(1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Marble work of 'Makrana White' 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, borders as in flooring and like in and over cement mortar screed of 20mm thick in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on walls of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound emulsion distemper over a coat of alkali reistant primer on walls over two coats of wall care putty complete all as specified and directed

Complete removal of existing treatment on wall surfaces of any description including brooming down with steel wire brushing, scrapping down smoke soot's , moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint (Apex Ultima or equivalent brand as specified in CA) over a coat of weather proof primer including filling the cracks etc with crack filling material all as per manufacturers instructions complete all as specified and as directed.

Rolled mild steel as in roof trusses (framed), trussed purlins crane gantries rails, wind tie and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc.,steel conforming to Fe 410-W (Gde-E- 250) quality-A all as specifeid and as directed.

Plain Cement Concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in sub base to floors, 100mm thick complete all as specified and as directed.

Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed.

Granite (of any type) slab 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing, rounding to edges of stone slabs one edge etc all as specified and as directed.

E/M WORKS

Concealed point wiring complete with 1.5 sq.mm single core PVC FR insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC conduit with accessories run on walls/ ceiling including MS terminal boxes fabricated with 1.6 mm thick MS sheet, mounted / concealed on walls with hylem sheet top cover 3 mm thick, fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 1.5 sq.mm PVC FR insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for :- (a) One light point controlled by one switch.

(b) One fan point controlled by one switch and regulator.

(c) one 3 pin switch socket out let 5 Amps on independent board.

Energy saving ceiling fans, 230 Volts, 26 Watts, single pole, 1200 mm sweep, high speed of approved colour with remote control and two years warranty certificate from the manufacturers, with latest BEE five star rating and BLDC technology all as per Havells Model No :- Efficiencia Neo (BLDC 26W) or techno commercially equivalent models specified in PS complete with down rod and GI hook with welding work, wire connections from ceiling rose to ceiling fans, with complete accessories including writing of MES No with unit name on ceiling fans using approved stencil with synthetic enamal paint complete all as specified and as directed.

Exhaust fan 230Volts, SP, 300 mm sweep, 900 rpm with BEE five star rating,high speed, heavy duty complete with louvers, clamps with screws nut and bolts, including wire connections from ceiling rose to Exhaust fan complete with all accessories including writing of MES No with Unit Name on Exhaust fans using stencil with synthetic enamel paint all as specified and as directed.

Concealed point wiring complete with 2.5 sq.mm single core PVC insulated unsheathed FR cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC rigid conduit with accessories run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with hylem/ laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switch socket outlets etc., incl provision of 1.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed.

Switch Piano, flush type, 5 Amps, 240 Volts single pole with ISI marked complete all as specified and as directed.

Switch socket combination 3 & 2 pin, 5 Amps, 240 Volts, flush type multipurpose controlled by one switch all as specified and as directed.

Switch socket combination 2 in 1, 3 pin and 2 pin, 5 and 15 Amps flush type, universal complete all as specified and as directed

MCB single pole 5 Amps to 40 Amps 240 volts complete all as specified and as directed.

Ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed.

LED batten fittings, 20 watts, 6000K, (4 feet long), suitable for indoor applications wall mounted with extruded aluminium heat shink provision, efficient heat dissipation and integrated electronic driver, industrial batten type, powder coated top cover, with bipin holders, connector block , lamp etc., complete all accessories internally pre wired all as per Bajaj, Cat No.BCLAB 20 WH LED P / Halonix Cat No. HLB-03-20-CW-AL or techno commercially equivalent makes specified in PS including connecting up twin core twisted flexible copper conductor cable all as specified and directed.

RCCBs double pole 30mA, 240 volts, 25 Amps complete all as specified and as directed.

Angle holder PVC/polycarbonate type all as specified and as directed.

MCB DB, SPN 8 ways, 240 Volts with 200 Amps rated busbar, double door for housing MCBs all as specified and as directed.

LED light fitting1x10 Watt, wall/ceiling mounted type with metallic channel and white reflector, suitable for mirror fittings with electronic driver, lamp holder, etc all prewired incl connecting up with flexible copper conductor cable all as specified and as directed.

Provision of GI bracket made out of 25 mm dia GI tubing light grade of approx length 1.5 m size fabricated to a shape incl necessary fixing clamps, bolts, nuts & washers all as specified and as directed.

LED buillding security light fittings, 1x20 Watt with high power LED and unique peanut lens to ensure uniform distribution, maintenance free system complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables complete all as specified and as directed.

Returning, filling in trenches including spreading leveling watering and well ramming in layers with hard/dense soil not exc 25 cm thick in each layer complete as specified and as directed.

Removing excavated soil to a distance not exc 1.5 mtr above the starting point complete all as specified and as directed.

Galvanised iron pipe of 25 mm dia, medium grade, laid in trenches with all fittings such as socket, bends, elbow, union etc., including connecting and testing complete all as specified and as directed.

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

25mm bore dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed.

Drilling and tapping cast iron/GI water main (in position) for branch connection of the internal dia 20mm complete all as specified and as directed.

Sand cushioning in layers for cables in trenches / ducts for cable using dry river sand including consolidation complete all as specified and directed. NOTE: Punned thickness will be measured for payment purpose.

Bricks, sub class 'B' of old size 230 mm x 115 mm x 75 mm laid in trenches for cable protection all as specified and directed.

XLPE insulated, galvanised steel strip or wire armoured and PVC bedded, heavy duty, LT cable 16 sq.mm, 2 core, 1100 volts grade with multi stranded aluminium conductor, including cable glands, cable lugs etc., to suit the cable size, laid in trenches, or fixed along with the poles, bare or through GI pipe, laid under floors / road etc., fixed / concealed in walls / encased in GI pipe etc., jointing and testing complete all as specified and as directed.

Earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge not less than 1.5 m below ground level connected to earth lead by GI wire 4 mm dia by means of bolts nuts, check nuts, washers made out of galvanised iron connected to main switch all as shown in elect plate No 3 of MES SSR Part -I includingn excavation and earth work in any type of soil,funnel, 20 mm dia light grade GI watering pipe with chamber of PCC 1:3:6 type C1 40mm thick of size 450mm x450mm (1:2:4) type B1 for cover slab reinforced with 8mm dia TMT bars 10cm c/c both ways and with 6mm MS hook etc complete all as specified including testing on completion all as specified and directed.

Galvinised iron tubing, light grade, 50mm bore with all accessories for cable protection fixed on poles/buildings or laid in trenches including necessary MS clamps, bolts and nuts etc., including taking down the existing complete all as specified and as directed.

LED tube light fitting, 1x10 watts , 230 volts, with long losting PVC body with slim & sleek looks all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as per Bajaj Cat No:10W CDL /Halonix Cat No: HLTLD- 041-10 W - CW or techno commercialy equivalent makes specified in PS complete all as specified and as directed.

MCB single pole and neutral 240 Volts, 32 to 63 Amps complete all as specified and as directed.

LED building security light fittings 1 x 30 Watts, housing made out of die cast aluminium in grey finish with clear acrylic and cast aluminium pipe mounting attachment, IP-66 degree of protection with all accessories and pre wired complete including PVC three core flexible copper conductor cable form ceiling rose to connector of fittings including GI bracket made of GI pipe light grade 25/40 mm dia 1.0 mm long bend in to shapes fitted to the wall with GI clamps of size 32 x3 mm all as per BAJAJ Cat No: EXNT PN30L WH CR PC SD / HALONIX Cat No: HLSLD -09-30 WWL-RL or techno commercialy equivalent makes specified in PS all as specified and as directed.

Excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables complete all as specified and as directed.

Cutting existing steel tubing for alterations or additions (each cut measured), screwing existing steel tubing for alterations or additions complete all as specified and as directed.

Taking down care fully aluminium/ copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, regulators, sockets, light fittings, fans etc and making good the disturbed surface of walls, ceiling etc including painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

XLPE insulated, galvanised steel strip or wire armoured and PVC bedded, heavy duty, LT cable 25 sq.mm, 3.5 core, 1100 volts grade with multi stranded aluminium conductor, including cable glands, cable lugs etc., to suit the cable size, laid in trenches, or fixed along with the poles, bare or through GI pipe, laid under floors / road etc., fixed / concealed in walls / encased in GI pipe etc., jointing and testing complete all as specified and as directed.

RCBO four pole 30 mA, 415 volts 63 Amps suitable for earth leakage ,over load and short circuit protection complete all as specified and as directed.

MCB DB, TPN 4 ways, 240 Volts with 200 Amps rated busbar, double door for housing MCBs all as specified and as directed.

Sub main wiring with two runs of single core 6 sq.mm, 1100 volts grade multi stranded copper conductor cable along with one run of 6 sq.mm PVC insulated single core multistranded copper conductor cable as earth continuity conductor drawn through and including non rigid PVC conduit medium grade of suitable size including taking down the existing complete all as specified and as directed. NOTE: Two runs of 6 sq.mm cable, one run of 6 sq.mm earth continuity conductor and one run of PVC conduit shall be measured as one unit for payment purpose.

Galvanised iron pipe of 32 mm dia, medium grade, laid in trenches with all fittings such as socket, bends, elbow, union etc., including connecting and testing complete all as specified and as directed.

LED building security light fittings, 1x45 Watt made up of pressure die cast housing with toughned glass and indl high power LEDs with secondary optics IP 66 protection and impact resistance complete all as specified and as directed.

Removing of unserviceable ceiling fan of any type and cleaning, servicing, greasing of bearing, rubber bush nuts and bolts & writing of MES/Sl No , spray painting with Duco paint of approved colour all as directed by Engineer -in -charge.

ADWITHI