752965A PROVN OF SINGLE OFFICERS ACCN FOR STUDENT OFFICERS AT MCTE MHOW (PH I OF II PHASES) (SPL WK)

Item No 57 : Supply and lay crushed stone aggregates 40 mm for loose filling to recharge pits etc complete all as and directed.

Item No 58 : M & L for boring holes of dia 150 mm dia hole up to 20 m deep and i/c 150mm dia GI Pipe 3.00 m below ground level and above ground level up to aggregate filling level all as specified and directed.

Item No 48 : Supply , installation commissioning and testing of Factory assembled S

ilent DG set with AMF panel of capacity 82.5 KVA, 1500 RPM , Turbo Charged, water cooled comprising of 105 BHP Engine with microprocessor based Genset controller with silencer and canopy for sound less mode (sound level not exc level specified by pollution control board) CPCB IV+ and alternator both mounted on a common base frame conforming to ISO-3046/BS-5514 and IS-10002 rated for 415 volts 50 cycles , 0.8 Power factor (PF) complete with residential silencer, AVM pads , battery with its leads, first fill of lub oil and all engine accessories such as self starter, alternator/dynomo with suitable coupling and base frame on foundation as recommended by the manufacturer and consisting of other electrical component and maintenance free battey including suitable size of copper cable lead with terminal, all mounting accessory and AVM pads all as specified comprising with the following.

Item No 43 : M & L Valve chamber of internal size 0.90m X 0.90m X 0.90m (internal dimentions) including excavation of earth work in any type of soil, 150mm thick PCC in 1:4:8 type D2 foundation , brick work in CM 1:6, 15 mm thick rendering in CM 1:4 to both internal and external surfaces upto 150mm depth below GL, PCC 1:3:6 type C1 as in coping, cover with two Nos of hinges and one No. handle made out of MS round bar 10mm dia with necessary locking arrangement including painting to the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as shown on drg and as specified. Note:- The estimated cost includes all earthwork and connected items.

Item No 44 : M & L Valve chamber of internal size 0.60m X 0.60m X 0.60m (internal dimentions) including excavation of earth work in any type of soil, 150mm thick PCC in 1:4:8 type D2 foundation , brick work in CM 1:6, 15 mm thick rendering in CM 1:4 to both internal and external surfaces upto 150mm depth below GL, PCC 1:3:6 type C1 as in coping, cover with two Nos of hinges and one No. handle made out of MS round bar 10mm dia with necessary locking arrangement including painting to the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as shown on drg and as specified. Note:- The estimated cost includes all earthwork and connected items.

Item No 45 : M&L for cutting of existing 80mm dia CI/DI water main for inserting for "Tee" of size 80x80x50mm dia for branch connection incl earth work all as specified.

Item No 47 : Supply and fix DOL starter for capacity suitable for 5 hp with all type of protection (i.e Single phase preventer, motor protection relay, water level detector sydtem etc)

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door including blanking plate for dummy space with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door including blanking plate for dummy space with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCCB four pole rated capacity 63 Amps, 415 Volts breaking capacity 16 KA, complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator modular type and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.0 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

SCHEDULE "A" PART-I (Building Work) Lump sum price worked out by the contractor for 'Building Work' as listed in Schedule 'A' Part-I against the lump sum price inserted by the MES.

Sch 'A' Part-II (Internal Water Supply) Lump sum price worked out by the contractor for 'Internal Water Supply' as listed in Schedule 'A' Part-II against the lump sum price inserted by the MES.

Sch 'A' Part-III (Internal Electrification) Lump sum price worked out by the contractor for 'Internal Electrification' as listed in Schedule 'A' Part-III against the lump sum price inserted by the MES.

Sch 'A' Part-IV (External Electrical Supply) Lump sum price worked out by the contractor for 'External Electrific Supply' as listed in Schedule 'A' Part-IV against the lump sum price inserted by the MES.

S & F for MCB DP rated capacity 16 Amps, (nearest standard size ) 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Old U/S Iron Scrap

Chowkhats or

frames not exc. 1.5 sq. m each incl iron mongeries.

Chowkhats or framesexc. 1.5 sq. m but n exc 4.00 sq.m each incl iron mongeries.

Item No 04 : S & F for MCCB adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu rating 63 Amps 16KA and including sheet steel. The enclosure shall be wall mounted with and including all fixing accessories complete all as specified.

Item No 05 : M & L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth 32 x 6 mm galvanized MS strip by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 3, connected to earthing test point including 15mm dia eavy Grade GI pipe for protection of GI wire up to test point and 40mm dia GI Pipe heavy Grade for watering with wire mesh, funnel complete including testing on completion all as specified.

OUTGOING (F) 4 Pole MCCB 63 Amps with rotary handle, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 16 KA breaking capacity including all fixing accessories with both ends spreader links -06 No (G) 4 Pole MCCB 40 Amps with rotary handle, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 16 KA breaking capacity including all fixing accessories with both ends spreader links -06 No (H) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm x 150 mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

NOTE:- Rate of earthwork and PCC work are deemed to be inclusive in this item. Contractor has to marked on panel and MCB/MCCBS for I/C location and O/G Location INCOMMING (a) Copper strip busbar of 500 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos

OUTGOING (F) 4 Pole MCCB 125 Amps with rotary handle, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -06 No (H) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm x 150 mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Item No 06 : M & L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 3, connected to earthing test point including 15mm dia eavy Grade GI pipe for protection of GI wire up to test point and 20mm dia GI Pipe heavy Grade for watering with wire mesh, funnel complete including testing on completion all as specified.

Old u/s Brick bats

Item No 07 : S & F for Galvanised iron strip of size 25 mm x 4 mm for earth contunity conductor complete all as specified and directed.

Old u/s stone slab, interlocking tiles, kota stone

Item No 02 : Design supply, install testing & commissioning passengers lift of capacity 8 passanger (544 Kg), speed 1.5 metre/sec, lift with single speed motor 415 volts, 3 phase, AC 50 Hz supply conforming to IS14665, suitable to serve G + 05 upper floors with AC Variable Voltage & Variable Frequency drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding stainless steel doors, Car Size- as per IS and suitable to install in lift well,Door Size- as per IS or manufacture specification, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set (04 Nos, one each in car, Machine room & near Ground floor landing door) & human interface device, all other Finishes Standard safety features should be as per IS specification and modern practices in market in lift complete all as specified below :-

Item No 08 : Supply, commsssioning, installation & testing copper wound distribution Transformer step down, outdoor type, plinth mounted maximum toatal losses inaccoradance to energy efficient level three as per IS 1180 amended no IV (Part-I) of 11/0.433 KV capacity 160 KVA, AC 3 phase, 50 Hz oil immersed naturally cooled delta connected on primery side (11 KV HV side) Dyn -11 with neutral brought out on secondary side with tapping at + 2.5% + 5% off load tap changer gear in steps of 2.5 % including initial oil fill to appropriate level & all standard fitting all as per IS 1180 amended no IV Pt-1 1989 and IS-2026 mounted on and including platform of size 2.5 Mx1.5M high (outer dimension) built with 150 mm thick PCC 1:3:6 type C2 foundation solid block as per manufacturer recommendationcomplete all as specified and directed.

Item No 09 : Supply and install outdoor type automatic power factor correction (APFC) panel factory made of 120 KVAR capacity ready to use design confiring to relevant IS rated for short circuit rating of 50 KA, front openable and lockable by keys having lowers and air vent, gasket and totally vermin proof and suitable for 415/440 volts, 3 phase 50 Hz, AC and housed in elegant enclosure fabricated from minimum 3.00 mm thick CRCA sheet, anti corrosive costing to achieve power factor from 0.9 to 0.99 and finally powder coated in texture seimens gray RAL 7032 & as directed by Engineer in charge comprising of and including following including suitable size and length of copper conductor cable from main panel to APFC panel for connection as approved complete all as specified and directed :-

Item No 10 : Supply and fixing aluminium pressure dia cast LED street light fitting 70 Watt 230 V AC outdoor type with high power LED source luminious efficacy 130 lm/watt,Correlated Color Temperature (Nom) 5700 K,Luminous Flux 9,800 lm, (CRI) >70,PDC housing, moulded type Driver high impact resistance (IK 10) with PC cover & Top openable access to drivers for ease of maintenance with inbuild SPD 5KV (or nearest higher size) , IP66 (Dust penetration-protected, jet-proof),Median useful life L70B50 of 50,000 hour(s), complete , Additional 10 KV surge protection device, Pf should be greater than 0.95 separete connector block for termination of incomming cable connection and provision of 2.5 sq mm three core copper conductor cable multi stranded from junction box to light fitting and necessary dia GI pipe medium grade 40mm dia bracket 1.5 mtr long bend to required shape with

Item No 11 : Supply, errecting, commissioning and testing of Gal

vanized steel High Mast of 16 Mtrs hight. High mast lighting system with its accessories. Mast shaft shall be in two sections, hot dip galvanized and suitable for wind velocity as per IS 875 Part 3 . It shall also include accessories for high mast including head frame, steel wire rope (7/19 construction) double drum winch,lightning arrester spike including RCC foundation, Galvanized Lantern carriage arrangement 'suitable for 09 Nos.luminaires Symmetrically & its control gear boxes and with 03 point suspension system. The mast shall have an integral power tool installed inside the base compartment for its operation. ( Material construction of high mast sheet will be of BSEN 10025 / IS 5986 or equivalent ) in and including the following accessories/items : (a) Supply of foundation bolts manufactured from special steel and Hot Dip Galvanised along with nuts, washers, anchor plates and templates. (b) Supply of feeder pillar panel of thickness 3.15mm with suitable size contactor, timer relay indicating lamp, digital voltmeter ammeter, incomming MCB and outgoing MCB with single dial timer control and raising & lowering mechanism for integral power tool.

Item No 12 : Supply ,fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 2500 mm x 1500 mm x 800 mm (over all dimension) made out of 3.15 mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6 mm vertical frame and legs with mild steel flat iron 25 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. . NOTE:- Rate of earthwork and PCC work are deemed to be inclusive in this item.Contractor has to marked on panel and MCB/MCCBS for I/C location and O/G Location

Item No 13 : Supply ,fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 1500 mm x 1500 mm x 300 mm (over all dimension) made out of 3.15 mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6 mm vertical frame and legs with mild steel flat iron 25 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. .

Item No 14 : S & F Integral decorative LED bollard with polycarbonate diffuser square shaped with IP 65 protection suitable for 9 watts Rechargeable LED bulb, luminous efficacy not less than 120 lm/watt with necessary MS base box made out of MS sheet of 2 mm thick of suitable size abbended in PCC 1:2:4 base, elecrical connections with adequate size complete as all specified and as directed.

Item No 15 : Supply and fixing cable route indicator, made of MS sheet of size 200 mm x 150 mm x 3 mm thick, spot welded with angle iron of size 40 x 40 x 5 mm thick, 750 mm long embedded in PCC (1:2:4) type B-2( using 40mm graded crushed stone aggregate) block 30cm x 30cm x 40cm in ground including one coat of synthetic enamel black paint over one coat of red oxide zinc chrome primer and writing with white paint showing size of cable HT complete all as specified & directed .

Item No 16 : Supply and fixing internal fire hydrant comprising of and including single headed stainless steel body fire hydrant valve , 80 mm inlet with single outlet with control and fitted complete with63 mm dia female instaneous coupling of stainless steel conforming to type " A " of IS : 5290-1977 on the outlet complete with orifice flangs as required with ABS plastic blank cap , steel chain adaptor as per IS Specifications as required including 6 mm thick Stainless Steel Orifice Plate of suitable size as required , complete all as specified and as directed by Engr-in-charge :-( note : rate quoted shall be deemaed to include for sealing of threaded parts with " Holdtite " )

Item No 17 : Providing and fixing first aid fire hose reel equipment conforming to IS : 884-1969 ( with upto date amendments ) , finished with post office red spray paint and complete with and including the following complete as required , as specified and as directed by Engr-in-charge

Item No 18 : Providing and fixing non percolating type 63 mm dia 15 metre long Reinforced Rubber Lined ( RRL ) Type ' A ' ISI marked ( IS - 636 ) , woven jacketed hose pipe tested to bursting pressure 32 Kg / Sq cm with and including gun metal male & female instantaneous type coupling approved by fire authority , ISI marked ( IS : 903 ) , machine wound with Gl wire with the pipe complete in ali respects , all as specified and as directed by Engr-in-charge.

Item No 19 : Providing and fixing fire hose cabinet of size 1250x1800x600 mm , weather proof , fabricated from 18 gauge MS sheet of fully welded construction with hinged double front door , partially glazed with 4 mm thick glass with locking arrangment duly painted with 2 coats of synthetic enamel postal red point over a coat of red 9 oxide zinc chromate primer with " Fire Hose Box " written on front , suitable to Each house 2x15 metre ( two lengths ) of canvas hose with couplings , branch pipe , One fireman's axe , first aid fire hose reel and hydrant outlet complete all as specified and as directed by Engr-in-charge

Item No 20 : Providing and fixing standard fireman's axe with heavy insulated rubber handle 11 complete all as specified and as directed by Engr-in-charge

Item No 21 : Providing and fixing gunmetal two way collecting head with 63mm dia instantaneous type inlet and 150mm dia flanged outlet with built - in check valve , ISI marked ( IS : 904 ) complete with bolts , nuts and rubber insertions including necessary support complete in all respect for fire brigade connection to underground tanks and wet risers complete all as specified and as directed by Engr-in-charge

Item No 22 : M & L for PN 1.6 rated air vent valve having brass body, cover, adopter, disc assembly & cap, stainless steel strainer, plastic float and 25 mm screwed threaded ends suitable for maximum operating temperature 100 °C installed on all high points in the water piping system to automatically remove the trapped air with necessary accessories all complete as specified and directed by the engineer-in-charge.

Item No 23 : S & F of orifice plate made out of 6 mm thick SS 304 with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete all as specified and directed by the engineer-in-charge.

Item No 24 : Providing and fixing 5 Kg capacity (or nearest higher standard size) by fixing arrangement carbon - di - oxide ( CO2 ) type fire extinguishers consisting of welded M.S. cylindrical body , squeeze lever discharge valve fitted with pressure indicating gauge , internal discharge tube , 30cm long high pressure discharge hose , discharge nozzel , suspension bracket , conforming ti IS : 2878 11.16 finished externally with red enam

Item No 25 : Providing and fixing 9 litre capacity(nearest higher standard size) with fixing arrangement water gas ( stored pressure ) type fire extinguishers consisting of welded M.S. cylindrical body , squeeze lever discharge valve fitted with pressure indicating gauge , internal discharge tube , 30cm long high pressure discharge hose , discharge nozzel , suspension bracket , conforming ti 5 : 6234 finished externally with red enamel paint and fixed to wall with brackets Each and also including intial charge complete all as specified and as directed byEngr-in-charge. ( Note : -1.The body of fire extinguisher shall be CCE approved with IS : 6234 marking and showing the filling / validity date ) ( Single officer living-20 Nos)

Item No 26 : Supply only of Fire Extinguisher Mechanical Foam type ISI Marked Foam (AFFF) type Fire Extinguisher 9 ltrs capacity (nearest higher standard size) with fixing arrangement fitted with Forged Brass squeeze lever discharge valve, conforming to IS : 15683 :2006, complete with initial refill consisting of ISI Marked CO gas cartridge of 60 gms capacity conforming to IS 4947 and ISI Marked AFFF conforming to IS : 4989, suitable for operating between + 50 degree centrigrade , Fire Rating Class - 3A & 34B ( for Parking of vehicles and DG set area)

Item No 28 : Supplying , installating , testing and commissioning of Electric motor driven fire pumping set consisting of and including the following complete all as specified and Eachse as directed by Engr-in-charge

Item No 29 : Fabricating , supplying , erection , testig and commissioning of totally enclosed cubicle type free standing , floor mounted , compartmentalised , sectionalised , sectionalised , dust , damp and vermin proof , with suitable natural ventilation arrangement , front and rear accessibly , lackable power cum control panel , fabricated from 2 mm thick CRCA sheet and angle iron , spray painted with approved colour shade , suitable for 145V , 50 Hz , 3 phase , 4 wire system complete in all respect and conforming to latest revised ISI specifications including necessary Eachset 100000.0 connections , inter - connections with copper conductor cable of required size , soldering etc. with and including following switch gears mounted thereon as required ( All switch - fuse / fuse switch unit shall be to AC 23 duty to 15 : 4064 ) ( location at Terrace Floor ) complete all as specified and as directed by Engr-in-charge

Item No 30 : 16sqmm x 4core PVC insulated copper conductor cable armoured + 2 Nos . 8 SWG Gl wire

Item No 31 : 2.5sqmm x 3core PVC insulated copper conductor armoured control cable .

Item No 32 : Providing , installing , testing and commissioning of the following complete with junction boxes complete as required , as specified and all as directed by Project manager :

(a) Semi recessed ABS body manual call box Complete with hinged cover

(b) Response indicator & Hooter on every floor as per IS Specifications

Item No 33 : Supplying and fixing MS steel conduit of following sizes complete with all cessories in surface / recess including painting in case of surface conduit , or ang the wall and making good the same in case recessed conduit as required , inuding fixing the exposed conduits by saddles with base plate after every 500mm diastence complete all as specified and as directed by Engr-in-charge

(a) 20mm dia

(b) 40mm dia

Item No 34 : Providing , fixing , testing and commissioning of 8 Zone Microprocessor based Fire Alarm Panel for Manual Call Box with response indocator as per IS 2189 : 1999 including the arrangement of Audio / Visual indications by dual lamps of fire and 1.26 faults in each zone and finished in slove , having sealed Nickel Cadmium Eachset 10000.00 maintenance stand and boost / trickle charger , DC voltmeter , short circuits healthy check etc. complete all as specified and as directed by Engr-in-charge

Item No 35 : Supply and drawing 2 x 0.75 sq mm PVC insulated copper conductor cable in the existing surface / recessed steel conduit and capping complete with thimble and ferrules as required conplete all as specified and as directed by Engr-in-charge

Removing the excavation soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

Item No 71 : S&F glass self complete all as specified and as directed. Make: Jaguar or equivalent in Hindware/ Parryware/Somany/Cera)

Item No 72 : S&F toilet paper holder brass chromium plated complete all as specified and as directed. Make: Jaguar or equivalent in Hindware /Parryware/Somany/Cera)

Item No 73 : S & F low-flow Basin Faucet, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipes or for brass ferrule of 15mm bore as per GRIHA norms complete Make Hindware/ Jaquar/ Parryware/Somany/Cera all as specified and directed.

Sch 'A' Part-VI (Road, Path & Hard standing) Lump sum price worked out by the contractor for 'Road, Path & Hard standing', excavation & earth works' as listed in Schedule 'A' Part-VI against the lump sum price inserted by the MES.

Item No 52: Supply, laying and testing of 150 mm inner diameter of double wall corrugated (DWC) high density polethelene pipes(HDPE) and stiffness class-8 (SN-8) with ISI marked (with CML No) with and including all fittings & jointing materials for sewage line and laid in trenches as specified in IS-16098(Part-2):2013 and as per manufacturer's instruction complete all as specified and as directed. Note:- Bedding of pipe shall not be provided in normal condition and construction methods shall be strictly compiled as per clause no A-4 Annex 'A' of IS 16098(Part-2):2013

Item No 70 : S&F corner self complete all as specified and as directed. Make: Jaguar or equivalent in Hindware/Parryware /Somany/Cera)

External Water Supply

D. ACCESSORIES (i) Suitable channel frame (ii) Storage battery of 1X12 Volts of suitable 150 AH capacity as per manufacturer instruction mounted on angle iron frame of suitable size as directed.

Each Job

External Electrical Supply (Stand by DG Set)

A. Engine : (a) Vertical multicylinder, cold starting in accordance with BS-5514/IS-10002 at 1500 PM including the following accessories :- (i) Fuel tank(Suitable for capacity for minimum 10 Hrs run). (ii) Fuel filter(Ore & Micro). (iii) Fuel feed pump(Inline monoblock/PT type) with governor. (iv) Lub oil filter. (v) Lub oil cooler. (vi) Dry type/oil bath type air cleaner. (vii) Exhaust Silencer(Industrial type). (viii) Radiator, Radiator fan & mounting. (ix) Fly wheel with starting ring. (x) Expansion bellow. (xi) Exhaust gas turbocharger. (xii) 12 Volt electric starter with 01 Nos maintenance free battery 150 AH capacity.

B. ALTERNATOR (i) Alternator, 3 phase, 415 Volts, 50 Hzs, 0.8 PF, 1500 RPM self excited, self regulated screen protected, drip proof alternator of capacity 82.5 KVA conforming to BSS 5000 (part 99) with insulation class "H", single bearing and automatic voltage regulator accessories

C. ACOUSTIC ENCLOSURE (i) Specially design to meet stringent MOEF/CPCB norms of 75 dBA @ 1 mtr at 75% load under free field conditions. (ii) Air inlet louvers specially designed to operate at rated load even at 50 degree C air inlet temp. (iii) Powder coated for long lasting service life and superior finish. . (iv) Insulation material meets exacting IS 8183.

Sch 'A' Part-VIII (Fencing and Gate) Lump sum price worked out by the contractor for 'Fencing and Gate' as listed in Schedule 'A' Part-VIII against the lump sum price inserted by the MES.

E. CONTROL PANEL The control panel shall be made of CRCA sheet duly fabricated and powder coated and complete with internal wiring, bus bar etc and fitted with the following accessories :- (i) MCCB 4 Pole 160 Amps 25 KA thermal release type – 01 No (ii) Digital Ammeter with CT of size 200/5A – 01 No (iii) Digital Voltmeter 3 Ph 415 volts – 01 No (iv) Microprocessor based DG set control unit with SIM enable - 01 No (v) Indicating lamps (LED type) (R-Y-B) – 01 set

(LAN Conduit)

Item No 36 : Providing and fixing flexible 20mm dia PVC conduit including fittings and all necessary supports , clamps , jointing pieces etc. for cable from slab to detector complete all as specified and as direcetd by Engr-in-charge .

Item No 37 : Providing & fixing wall mounted Emergency Instruction Plate consisting of 32 instructions printed on acrylic sheet . ( Note : Instruction shall be with at least 50mm high letters , computer screen 33 printed on acryclic sheet )

Item No 38 : Supply and fix Sprinkler glass upright type (Standard response) as per IS:15106/TAC

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Item No 63 : S&F low flow chromium plated shower rose 120x120 mm size with CP arm 300mm long with swivel joint fixed to pipe etc as per GRIHA 3 star rating norms complete all as specified and directed. Make: Jaguar (Roca) Cat pot no T9901A1GF or equivalent in Hindware/Parryware/Somany/Cera)

Item No 64 : S&F low flow chromium plated health faucet with 8mm dia and 1.5 m long flexible tubes and wall hook suitable for EWC including nut/washer as per GRIHA norms 3 star rating complete all as specified and as directed. Make: Jaguar Cat pot no G573 or equivalent in Hindware/Parryware/ Somany/Cera)

Item No 65 : S&F CP WHB single lever basin mixture suitbale for counter type basin (as approved by PMG) 15 mm bore dia chromium plated fancy type screw down high pressure with crutch or butterfly handle, screwed both ends for iron pipes for unions complete all as specified and as directed. Make: Jaguar/Hindware/Parryware/Cera/Somany)

Item No 66 : S&F low flow chromium plated 3 hole wall mixer 15 mm dia including provision of over head shower as per 3 star griha rating complete all as specified and directed. Make: Jaguar Cat pot no G3154A1GF or equivalent in Hindware/Parryware/ Somany/Cera)

All as per Item No 1 above but excl 1.50 not exceeding 3.00 m depth.

Item No 67 : S&F of UPVC waste pipe of 40 mm dia suitable for wash basin/sink etc complete all as specified and as directed.

Item No 68 : S& F CP brass tubular towel rail 60 cm long, 20 mm dia fixed with pvc rawl plug with steel screws as per Griha norms 3 star rating complete all as specified and as directed. Make: Jaguar or equivalent in Hindware/Parryware/ Somany/Cera)

Item No 69 : S&F 125 mm long soap dish brass chromium plated as per Griha norms 3 star rating complete all as specified and as directed. Make: Jaguar or equivalent in Hindware/Parryware/ Somany/ Cera)

S& F 16mm outer dia CPVC hot water pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors as per GRIHA norms complete all as specified.

INCOMING (a) Copper strip busbar of 800 amps rated capacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos (b) MCCB 4 Pole 400 Amps, Microprocessor based Fully rated neutral with in built protection, Over load, Shortcircuit, Instantaneous & Earth-fault protections, Short circuit

breaking capacity 35 KA .

Item No 74 : SS & F for sheet metal enclosure MCCB DB VTPN 6way Vertical type with 200 Amps rated bus bar 415 volts, IP 54 protection for incomming MCCB 4 pole -01 Nos and out going MCB SP -18 Nos with double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S& F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors as per GRIHA norms complete all as specified.

S& F 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors as per GRIHA norms complete all as specified.

S& F 40mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors as per GRIHA norms complete all as specified.

S & F PPR Ball valve (ISI Marked), with CPVC or PPR handle, plain both ends for CPVC pipe for unions of 25 mm bore, as per GRIHA norms complete all as specified and directed.

S & F PPR Ball valve (ISI Marked), with CPVC or PPR handle, plain both ends for CPVC pipe for unions of 40 mm bore, as per GRIHA norms complete all as specified and directed.

Item No 75 : S & F for sheet metal enclosure MCB DB VTPN 8way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No 76 : S & F for MCB Single pole rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No 77 : S & F modular MCB protected socket comprising of 24A MCB C curve, and 16/20 A Socket for AC/Geyser, modular switch 16A complete with Sheet metal Enclosure for 230 volt 50 Hz AC including all acessories as one complete set all as specified and as directed .

Item No 78 : S & F modular type LAN Socket RJ 45 with complete box

Item No 79 : S & F modular type Telephone Socket RJ 11/12/14 with complete box

Item No 80 : S & F BNC Socket with connector with complete box as directed by Engr-in-Charge

SCHEDULE "A" (Schedule of Credit) Note : Contract sum shall be arrived at after deducting the amount of Schedule of Credit Rs 165400.00 (Minus) inserted by MES from the total quoted amount.

Item No 59 : S&F angle stop valves, 15 mm bore fancy type chromium plated, with crutch or butterfly handle, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed. Make: Jaguar or equivalent in Hindware/Parryware/ Somany/Cera

Item No 60 : S & F low-flow Bib taps, fancy type, chromium plated, with crutch or butterfly handle,screwed down, screwed for iron pipes or for brass ferrule of 15mm bore as per GRIHA norms complete Make Jaguar/Hindware/Somany/ Parryware/Cera all as specified and directed.

Item No 61 : S & F low-flow Kitchen Faucet, fancy type, chromium plated, with crutch or butterfly handle,screwed down, screwed for iron pipes or for brass ferrule of 15mm bore as per GRIHA norms complete Make Hindware cat pot no F280020GRPC or equivalent of Jaquar/Parryware/ Somany/Cera all as specified and directed.

Item No 62 : S & F CPVC Male Brass Treaded Adopter (MBTA)/Female Brass Threaded Adopter (FBTA) of approved makes as per GRIHA norms 3 star rating complete including testing of pipe line all as specified and as directed

S & F for MCB DP rated capacity 25 Amps, (nearest standard size ) 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

( Note : -rate quoted for item 1.1 to 1.6 shall also include for cost of hangers and clamps as required and also include all civil breakages and making good the same )

(a) 100 mm dia

( b) 80 mm dia

Providing , fixing , testing and commissioning single acting air - cushion tank of 200mm dia and 1000mm high with dished top , made of minimum 6mm thick M S 13 pipe / plate complete with and including 25mm dia gun metal stop valve , 25mm dia air - release valve , pressure gauge and all accessories as required , as specified and as directed by Engr-in-charge

Schedule 'A' Part XV

Schedule 'A' Part-XVI

Schedule 'A' Part-XVII (Miscellaneous items of works)

Schedule 'A' Part-I

(Building works)

Item No 42 : Sign of size 450 MM X 150 MM reading 'FIRE POINT' in 12.5 mm block letters in White and Red background, properly spaced to provide good legibility located directly in corridor near to each Manual call point/Fire Extinguisher and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level

Item No 49 : Supply and fix Aviation obstruction light LED type comprising of aluminium housing with polycarbonate enclosure complete including standard fixing arrangements all as specified and as directed. (For RCC OH tank - 01 )

Item No 50 : Cable PVC insulated armd PVC sheathed LT 1100 V grade with copper conductor of size 3 core 2.5 sqmm multi stranded conductor laid

Total Amount

Signature of Contactor

(a) 3.5 core x 300 Sqmm (Transforner LT panel No1 & 2)

Item No 51 : S&F Automatic Street Light control switch for single phase load of 5KW, using infrared sensor based NATURE SWITCH for automatic switching of street light, Nature Switch operation should be based on Natural Light Lux level. Required illuminance level for switching ON is < 30 Lux and for witching OFF > 10 Lux. The Sensor along with 03 Nos contactors each of 20 to 25 Amps capacity, Incoming MCBs and Outgoing MCBs of 20-25 Amps of (03 Nos) and auto/manual operation (Sensor by Pass), Sixe of circuit wiring should be multistarnded FRLS min size of 10 Sqmm should be enclosed in a pole/wall mounted enclosure made of rust proof, Electric shock Proof, Termite proof and FR gradeSMC Junction box conforming to IP54 and model Swadeep 02EC5KW3P complete all as specified and directed.

M & L sub main wiring with 02 runs of 6 sqmm main wire along with 01 run of 06 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed / surface conduit (medium grade) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same & taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable - Havells / Finolex / RR Kabel Ltd. / L&T/polycab Make of PVC Conduit( FRLS) - Presto Plast / Finolex / Jindal / Asian / AKG/polycab

M & L for PN 1.6 rated 100 mm NB Cast irom (CI) 'Y' type strainer for suction conforming to IS 907: 1984 with SS filter screen and flange drilling standard end connection conforming to IS 1538: 1993 and necessary accessories for suction side of fire pumps complete all as specified and directed by the engineer-in-charge (at pump suciton).

Schedule 'A' Part VII

Construction of Block of single living Accn (S+5) incl stilt garages as per GRIHA 3 star rating, sanitary fittings, sanitary plumbing work upto & including 1st Manhole, Water storage tank, ATT, Water proofing treatment and all as shown on drawings and as specified. complete all as specified & shown on drawings.

Each Block

Construction of Block of Servant Qtrs (G+2) storey as per GRIHA 3 Star Rating norms sanitary fittings, sanitary plumbing work upto & including 1st Manhole, Water storage tank, ATT, Water proofing treatment and all as shown on drawings and as specified. complete all as specified & shown on drawings.

Construction of Block of pump house as per GRIHA 3 Star Rating norms sanitary fittings, sanitary plumbing work upto & including 1st Manhole, Water storage tank, ATT, Water proofing treatment and all as shown on drawings and as specified. complete all as specified & shown on drawings.

Construction of UG Sump 25000 Gallons capacity complete all as specified & shown on drawings.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part III

S & F PTMT connections pipe 15mm size with brass nuts of length 600mm, complete all as specified and directed.

S & F Bottle trap 32mm of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms), as per GRIHA norms complete all as specified and directed.

Schedule 'A' Part XIV

Internal water supply

(i) Male Brass Treaded (MBT)/Female Brass Threaded (FBT) Elbow 20 mm

(ii) Male Brass Treaded (MBT)/Female Brass Threaded (FBT) Tee of 20 mm internal dia

(iii) Male Brass Treaded Adopter (MBTA)/Female Brass Threaded Adopter (FBTA) of 20 mm internal dia

(iv) Male Brass Treaded Adopter (MBTA)/Female Brass Threaded Adopter (FBTA) of 25 mm internal dia

(Internal Electrification)

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with modular sunken box min 1.2mm thick, duly covered with modular white colour plate with frame and other necessary accessories ncluding PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 Amps

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(f) One bell point controlled by one, bell switch 5 Amps

Point

Description all as per item No 1 here in before but using 2.5 sq mm single core copper conductor two nos cables of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No. 1 here in before but using 4.0 sq mm single core copper conductor two nos FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/16 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete.

Item No 53 : S&F factory made SFRC MH cover with frame confirming to IS 12592:2002 HD 20 grade, of size 600mm circular sorrounded with steel strip 70 x 1.5 mm reinforced shall be as per relevant IS and laid over man hole brick work or concrete in CM 1:4, including reinforcement as perrelevant IS, complete all as specified and as directed by Engr-in-Charge. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete. (b) M/s KK Manhole. Or equivalent as approved by GE. (ii) Contractor shall provide PV alongwith manufacturer test certificate of SFRC cover. (iii) Reinforcement shall not be measured and paid seperately

Item No 54 : RCC Septic tank designed to carry sewage and sludge water, excavation in any type of soil, PCC 1:4:8 below the foundation, RCC M-30 design mix in walls, base slabs, baffle walls and roof slab including beams etc ewith Vent shaft, Manhole openings with cover connection etc, complete with Effective depth of 1.5m and over all depth of 3mtr for 100 users septic tank of conventional type complete all as specified and directed.

S & F modular switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

Item No 55 : Construction of soakwell 2.40 Mtr dia x 3.00 Mtr depth incl excavation,in any type of soil,foundation in PCC 1:3:6, walls of honey combing masonary with top ring og M 25 concrete incl intercepting and screen chambers made of brick masonary in CM, RCC cover slabin M 25 complete filled with brick bats complete all as specified and directed.

S & F modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F modular switch piano flush type, single pole, two way, and 5/6 Amp single module complete all as specified.

S & F modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F Bell push modular 6 Amps single module complete all as specified.

Item No 56 : Supply and lay broken bricks of gauge 80 to 50 mm for loose filling in soakge pits,recharge pits etccomplete all as and directed.

S & F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

M & L for Sub main wiring with approved colour coding

as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit, Note :- Each dwelling unit submainwiring to be properly tagged near incomming and out going area, i.e LT Panal , sub panel, Smart meter , and DB to locate the end to end for clear indication markings.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit, Note :- Each dwelling unit submainwiring to be properly tagged near incomming and out going area, i.e LT Panal , sub panel, Smart meter , and DB to locate the end to end for clear indication markings.

S & F for MCCB four pole rated capacity 125 Amps, 415 Volts breaking capacity 16 KA, complete all as specified and as directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part IV

(External Electrical Supply)

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in deep and getting out for laying of cable/ pipes etc including forming bottom surfaces to the required level/slope complete all as specified and directed

Excavating in trenches exc 1.5m wide but exc 1.5m and n exc 3.0m deep for foundation of poles strut/stays etc n exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning , filling in includiing spreading levelling, watering and well ramming in layers not exceeding 25 cm thick in soil comlete all as specified and directed

Removing surplus excavated to a distance not exc 50 mtr and depositing where directed at level not exc 1.5mtr above the starting point complete allas specified and directed.

Material and labour for approved river sand cushioning for under ground cable in trenches 8 cm before laying and 15cm after laying of cable and punned thickness of sand shall be measured and paid for 18 cm only after punned /consolidated thickness complete all as specified and directed

Supplying and laying un-reinforced precast concrete cable cover, class HV, Type-2, flat, size 450mm x 180mm x 40mm, ISI marked, laid flat across the cable length for cable protection embossed with HT 11 KV electric on the top surface complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type-1, flat, size 250mm x 150mm x 40mm, ISI marked, laid flat across the cable length for cable protection embossed with LT 1100 Volts electric on the top surface complete all as specified and directed.

M&L for PCC (1:4:8), type D2, using 40mm graded stone aggregate in foundations of poles, filling and mass concrete including form work if required complete all as specified and directed.

M&L for PCC (1:3:6), type D2, using 20mm graded stone aggregate in coping of poles with & including necessary use & waste of form wk for fair finished surfaces complete all as specified and directed.

Supply and laying Galvanised iron pipe "light grade" with all fittings for passing of cabes fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable of fllowing sizes of dia bore complete all as specified and directed.

100 mm dia

80mm dia

50 mm dia

40 mm dia

20 mm dia

Supply , laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) conforming to latest relevant IS with multy stranded aluminium conductor, 11000 volts grade of size 3 core 95 mm cable laid in trenches/ducts/under p

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of following sizes complete all as specified and directed.

Supply and fix cable termination jointing kit for 11 KV grade cable, cold shrink type complete with jointing material and accessories suitable for 3 core XLPE, armoured, aluminium conductor cable of size 50 sqmm to 95 sqmm, outdoor type complete all as specified and directed.

linth floor passing through pipe etc, fixed on wall complete all as specified and as directed.

M&L for Precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings cover slab (for manholesw etc) and similar work incl necessary form work and set in CM 1:4 complete all as specified and directed.

Supply and fix cable termination jointing kit for 11 KV grade cable, cold shrink type complete with jointing material and accessories suitable for 3 core XLPE, armoured, aluminium conductor cable of size 50 sqmm to 95 sqmm, indoor type complete all as specified and directed.

M&L removing of surplus material n exc 50m and deposited where directed at a level not exc 1.5m above the starting point

M&L for Boulder pitching, laid dry, hand packed tightly

M & L for Concrete bed to drain pipes of 300 mm dia of cement concrete 1:3:6 type C2 including packing under and completely surrounding pipes with concrete after they are laid and testedcomplete all as specified and directed.

M & L for Two coats of synthetic enamel paint over primer incl preparation of steel surfaces complete all as specified and as directed.

(b) 3.5 core x 240 Sqmm (Transforner servent qtr panel

Supplying, installation and erection steel tubular swaegd poles welded for provision of 2 pole structure complete with MS base plate 6mm thick and of size 300mm x 300mm, final taper, pole cap, bolts, nuts, washers & screw etc pole made out of ERW MS tubing conforming to IS-2713 part-II type 410 SP-55 (11 meter long) including of holes of reqd Nos and size for fixing of cross arms, painting with one coat of red oxide primer and two coat coats of aluminium paint for exposed surfaces, and two coat of black bituminous paint for portion embedded in concrete painting with synthetic enamel paint (First grade/quality) black & White colour at lower portion of exposed pole starting from plinth block band of 1200mm height ( 4 Nos EACH STRIP OF 150 MM WIDTH), PAINTING POLE NO BY THE BLACK PAINT by stenciled letter/figures of 8 cm height complete all as specified and directed. ( Note :- Earthwork, cement concrete Wk, Cross arm etc will be measured and paid under relevant items.)

Supply only for chain link MS galvanised fencing any size any type complete all as specified & directed.

M&L for cross arms, bracings, supports, clamps and back plates etc fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for fixing light fittings and painting with aluminium/silver paint in two coats on one coat of red oxide primer complete all as specified and directed.

(b) MCCB 4 Pole 250 Amps, with Microprocessor based Fully rated neutral with in built protection, Over load, Shortcircuit, Instantaneous & Earth-fault protections, Short circuit breaking capacity 35 KA @440 volts AC, - 01 No.

S & F pin type polymer insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150 mm height, 150 mm dia for 11000 Volts grade complete all as specified and directed.

M & L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 25 x 20 cm size complete all as specified and directed.

Supply and fixing post top lantern LED type 40 watt 230 watt, luminoous efficacy not less than 120 lm/watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

S & F Disc type polymer insulator 145mm high and 255mm dia ball and socket type, white, brown or green for 11000 volts grade complete all as specified and directed.

Excavation in trenches in hard /dense soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in deep and getting out for laying of cable/ pipes etc including forming bottom surfaces to the required level/slope complete all as specified and directed

Excavating in trenches exc 1.5m wide but exc 1.5m and n exc 3.0m deep for foundation of poles strut/stays etc n exc 10 sqm on plan and getting out in hard /dense soil complete all as specified and directed.

M & L for loose filling with aggregate of size 40mm graded stone aggregate of 20 cm thickness around at 2 poles HT structure complete all as specified and directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part V

(External Water Supply)

Supply and fix GI strip 32 mm x 6 mm buried in ground complete all as specified. ( as ground conductor)

Supply and fix Tubes medium grade galvanised of size 40 mm with all fittings and fixed complete for suuporting the air temination rod and protection of GI strip complete all as directed

M & L for PCC (1:2:4) type B-1 (using 20 mm aggregate) as fixing of pipe on roof for air teriminators etc including form work & finishing the surfaces even & smooth with out using extra cement complete all as specified.

Supply and laying for galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc in trenches complete all as specified and as directed of following sizes :-.

(a) 50 mm (2”) dia. (Officers Accn )

(b) 25 mm (1”) dia. (Officers Accn inlet)

(c) 20 mm (3/4”) dia. (Garden water connections)

(d) 15 mm (1/2”) dia. (Garden water connections)

S & F for gun metal gate valve with iron wheel head screwed both ends ISI marked fixed to GI pipe complete all as specified and as directed of following sizes :-

(a) 50 mm (2”) dia

(b) 25 mm (1”) dia

(c) 20 mm (3/4”) dia

(d) 15 mm (1/2”) dia

Total carried over to BOQ Rs.

SIGNATURE OF CONTRACTOR

DATED _________

Schedule 'A' Part VI

(Road, Path & Hard standing)

Excavation over area n.exceeding 1.5M deep and getting out in soft /loose soil

Surface dressing n exec 15 cm deep and getting out soft/loose soil.

Removing excavated material exc 250m but n. exc 500m and depositing where directed at a level n. exc 1.5m above the starting point.

M&L for filling in road formation with moorum in layers n.exc 15cm thick spread, levelled and rammed including watering

Rolling and consolidation of formation surface in cutting with power roller exc 8 tonne & n exc 12 tonne roller

M & L for laying and compacting 150 mm thick (compacted thickness) Granular sub base course (GSB) grading as per Grade II as specified in Table 900-1 of MoRTH specifications for road and bridge works 2013 in a sand crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required. The materials are mechanically mixed, spread and levelling on the subgrade by using motor grader of adequate capacity 80-100 Kn static weight for achieving requied compaction density consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per directed with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridges works 2013.

Supply and fixed Rigid non-metallic PVC conduit of external dia 25mm exclusive of boxes (Junction/terminal) but inclusive of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts saddles pipe hooks etc copmlete all as specified duly concealed in the wall for AFNET or any other tele communication cables complete all as specified and as directed.

M&L providing and laying dry lean concrete (DLC) 100mm thick of aggregate gradation as per Table 1 of SP 49 2014 having 7 day average compressive strength not less than 7 Mpa minimum cement content not less than 140 Kg/Cum DLC mixed in batching plant transported to site and laid by electroninc sensor paver including spreading and compacting using high amplitude tamping bars of paver (initial compaction) further by double drum smooth wheeled vibratory rollers with 80-100 Kn static weight to achieve minimum dry density necessary finishing etc complete all as specified and tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge work 2013

M&L for pavement quality concrete (PQC) of minimum 28 days field flexural strength of 45 Kg/Sqcm of 4.5 MPa aggregate gradation as per table 3 of IRC 15-2017, coarse aggregate of clean, hardstrong dense non-porous and durable pieces of crushed stone or gravel, fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 360 kg/cum of cement with non-circular virgin synthetic fibre of 12-18 mm length, specific equivalent dia 15.40 micron minimum melting temprature as 240°C and minimum tensile strength of 300 Mpa and at the rate as specified by the manufacturer PQC laid, spread and compacted with curing and tining by Texturing cum curing Machine complete all as specified and directed required surface texturing to be done as specified in clause 10.1.14 and table 9 of IRC 15-2017 complete.

Supply only polyester triangular fibres as secondary reinforcement in all types of concrete and mortars

Finishing surface of concrete roads pavements by belting

Forming contraction joints 65mm deep X 10mm wide, filled with sealing compound Grade A

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `A' for 200mm thick concrete slab

Forming construction joints30mm deep X 10mm wide, filled with sealing compound Grade A

Supply and fixed Junction boxes(1 to 4 way) 25 mm dia copmlete all as specified and d

Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions.

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth : for foundation and getting out in ant type of soil

irected.

Obstruction Lights

Laying and compacting 75 mm thick (compacted thickness) Wet Mix Macadam (WMM) grading as pe table 400-13 of MaRTH specifications for Road and Bridge works 2013 manufactured in WMM plant Laying and compacting 75 mm thick WMM comprising of clean, crushed, graded aggregate and granular material premixed with wate to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-1OOKN static weight and consolidating to required gradien and camber complete all as specified and directed The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge.

M & L for preparing bituminous surfaces of roadand marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. NOTE:- Application shall be carried out through mechanical appliances by the approved applicator of the manufacturer of paint.

M&L for PCC 1:4:8 type D2 using 40mm graded aggregates in foundation filling and mass concrete as in lean concrete

M&L for PCC 1:3:6 type C2 using 40mm graded aggregates in foundation filling and mass concrete as in lean concrete

M&L for brick work with fly ash brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

M & L for 600 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars

M&L for Pre-cast cement concrete (1:2:4) type B-1 using 20 mm graded stone aggrgates ) set in CM 1:4 as in landing, cover slab(for manholes etc) chulla hoods, chajjas, water trough, mangers, shelves and similar article with plain faces including form work complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material / Debries obtained from demolition to a distance not exc 50.00 mtr and depositng where directed etc complete all as specified and as directed

M&L for preparing new plastered surface of wall surface and applying three coats of white wash etc complete all as specified and as directed

Total carried over to BOQ Rs.

Signature of Contactor

Item No 41 : Sign of size 150 mm X 600 mm, posted and maintained within each stair enclosure on every floor, indicating the 'Floor Number' in bold type and at 75 mm high numerals in red and white background, securely attached to the stair side of the door in a way that the bottom of the sign is not above 1.5 m from the finished floor level

(Sewage Disposal)

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation etc for for shafts, wells cesspits, manholes, piers holes etc not exceedin 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in loose/soft soil etc complete all as specified and as directed

M&L for plain cement concrete 1:3:6 type C-2, with using 40 mm grades stone aggregates as in foundations and mass concrete etc complete all as specified and directed

M&L for brick work sewer bricks straight or curved on plan exc 6 m mean radius for man-holes/septictank/ soakwell etc in sewer works built in CM 1:4 etc complete all as specified and as directed

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates as in surface channels and drains complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc all as specified.

M&L for brick work with fly ash brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

M & L for 600 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part VIII

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Rain Water Harvesting

(Fencing and Gate)

24. M & L for Two coats of synthetic enamel paint over primer incl preparation of steel surfaces complete all as specified and as directed.

26. M& L for 20mm thick Granite (of any type) tiles machine cut in skirting/dado laid over cement screed bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor finishes in CM 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing.

Excavation in post holes each n.exc 0.5 Cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 2Cum watering out rawing and removing surplus soil to a distance n.exc 50m and making good in hard and dence soil.

M & L Cement concrete in foundations, filling and mass concrete Type D2, 1:3:6 (40mm graded aggregate)

M&L posts and struts in fencing including cutting tops to shape as directed, drilling holes, matching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or reveting etc an simillar work confiring to Fe-

Supply only mild steel bars 10mm dia and over cut to length, bent to shape required including ranking etc confirming to Fe-290 grade E-165

Supply only MS chain link fencing, any size or type.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of straights, rails strading bolts etc including provision of binding wire.

S&F MS bolts, screw (machine made( with hexagonal or spare head one end and screwed the other, or screwed bolts ends, each screwed end to be fitted with washer and one hexagonal or squaremeter 5 cm long.

M&L two coats of synthetic enamel paint over a coat of reoxide primer including preparation of any descrip

tion over 10cm width or girth.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in hard/dense soil for pillars

PCC 1:4:8 type D2 (using 40mm graded aggregate in foundation/bed concrete.

M&L for use and waste of Formwork in rough finished surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams in rough finish of concrete surface etc all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for R.C.C (20 mm graded aggregate in Design mix of M-25) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc all as specified and directed.

M&L for use and waste of Formwork in rough finished surface to sides of pillars, posts, struts, piers, columns and stanchions in rough finish of concrete surface etc all as specified.

Ditto,as above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for R.C.C (20 mm graded aggregate in Design mix of M-25) for Columns, pillars, piers, posts etc all as specified and directed.

M & L rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement.

M&L for preparing new plastered surface of wall surface and applying two coats of cement base paint etc complete all as specified and as directed

S&F 160mm dia PVC (SWR) rain water pipes perforated type single socket in any length with rubber ring/jiont fixed to walls/vertically with necessary pvc clamp.

Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25cm in hard/dense soil

Removing excavated material /Debries obtained from demolition to a distance not exc 50.00 mtr and depositng where directed etc complete all as specified.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part IX

Removal of excavated soil to a distance exceeding 250 M but n exc 500m and depositing where directed at a level not exceeding 1.5 m above starting point.

S& F Fe 410 -W (Gde- E- 250) quality- A framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S & F 1.60 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, weded to steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for RCC M-25 (Design Mix) as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

(Area Drainage)

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth for foundation and getting out in ant type of soil

M & L for PCC (1:4:8) Type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

S & F TMT reinforcement bar 6 to 10mm dia and over cut to length bent to shape requred incl cranking bending with MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter rough finished surfaces of concrete.

Use and waste formwork to faces of walls, retaining walls abutments, parpets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to batter curved and rough finished surfaces of concrete.

M&L Mild steel TMT bar 10mm dia and over cut to length bent to shape required incl cranking bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securin with clips complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for bricks work fly ash modular size bricks of compressive strength not less than 75 kg/sqcm strainght or curved on plan exc 6m mean radius joints built in cerment mortar 1:4 complete all as specified and directed.

M & L for preparing bituminous surfaces of roadand marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. NOTE:- Application shall be carried out through mechanical appliances by the approved applicator of the manufacturer of paint.

M&L for Rendering 15m thick in cm 1:4 on fiar faces of brick work or concrete furface of wall and finished even and smooth without using exstra cement complete all as specified and directed.

M&L for brick work with fly ash brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

M&L for preparing new plastered surface of wall surface and applying two coats of cement base paint etc complete all as specified and as directed

M&L for Extra for forming fiar finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds,mitred/stopped ends etc complete all as specified and directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part X

(Solar Water Heating System)

Supply, Install, Testing and Commissioning of 'Solar Hot Water System' of capacity 300 LPD with three layered evacuated glass tubes as a solar Collector, including , hot water tank duly insulated the outside surface with 50mm thick PUF insulation of density as per IS standard including vapour barrier over which cladding with 26 SWG aluminium sheet shall be provided with water proof joints to prevent any seepage of water / water vapour, foundation, all fixing and supporting accessories and electrical back up facility complete all as specified and as directed.. Note:- (a) The Solar Geyser shall be ISI Marked and MNRE approved make. Necessary approval certificate shall have to be produced to GE before approval of sample/make. (c) The Staging for solar water heater should be capable to bear wind pressure shall have to be got approved from OEM/any other govt institute before starting of fabrication work.

Supply & lay Hot water pipe duly inslulated with glass wool and aluminium cladding 50 mm bore complete all as specified and directed.

Supply & lay Hot water pipe duly inslulated with glass wool and aluminium cladding 25 mm bore complete all as specified and directed.

Supply & lay Hot water pipe duly inslulated with glass wool and aluminium cladding 20 mm bore complete all as specified and directed.

Sppply & Laying XLPE insulated, armoured, electric cable with aluminium conductor,multi stranded 1100 volts grade of size 50 sqmm 3.5 core , laid in trenches, fixed on poles / walls or passing through pipes including provision of necessary lugs and glands & making necessary connection complete all as specified and directed

S&F GI tubing, light grade, ISI marked 40 mm bore pipe laid in trenches/duct or in road crossing or fixed to wall/poles for protection of cable complete all as specified and directed.

S & F for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curveminiature circuit breaker (MCB) of 4P 63 Amps and current carrying capacity in the MCB DB complete with connection testing and commissioning

Item No 39 : S & F of the following type of signages made out of 3 mm thick opaque PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners complete all as specified and directed by the engineer-in-charge.

S & F Rotational moulded polyethylene water storage tanks of capacity 500 Ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I .

M&L for M.S.(Conforming to Fe.290.Gde-E-165) framed structure for staging of 500 Ltr capacity PVC makeup water tank, duly welded, rivetted etc and fixed on roof top above 6th floor through grouting bolt and P.C.C. and duly painted with 2 coats of synthetic enamel paint over a coat of red oxide metal primer all as specified and as directed. (Structure design should be vetted through Any Govt Engg institute).

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part XI

Supplying installing, fixing, commissioning and testing of Air break gang operated triple pole switch out door type of capcity 200 Amps AC mechanically operated mounted on polymer based insulator and steel frame with operating mechanism worked from ground level and polymer based Drop-out fuse set (set of 3 Nos) mounted on insulator with steel frame with Expulsion fuse carries and fuse element upto 25 Amps complete with locking arrangements including pad lock with key complete suitable for 11 KV, HT 50 Hz complete all as specified and directed.

Fire Fighting System

(Fire Fighting System)

Supplying , laying , jointing and testing " Heavy Class ( C - Class ) " mild steel pipe of following sizes , conforming to IS : 1239 ( Part - 1 ) ( 1974 Print ) and IS : 1239 ( Part - II ) ( 1979 Print ) including amendments thereto and also flanges and fitting such as bends , elbows , tees , reduscers , nipples , coupling caps , unions , flange joints , ruubber insertions and galvanised nuts and bolts , confirming to IS : 1239 ( Part - 1 ) ( 1974 Print ) including fixing the pipe on wall / celling with suitable M.S. strip / clamps / bracket and painting with one coat of red qxide zinc chromate primer and two coats of synthetic enamel posted red paint complete as required , as specified and all as directed by Engr-in-charge for the following size

100 mm dia

80 mm dia

65 mm dia

50 mm dia

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting,luminous efficacy not less than 120 lumen/watt 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor and flexible conduit of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

40 mm dia

Each set

n ) Push button starting switch panel at ground floor level for operation of the pump set including connections at main panel on terrace and push button switch at ground floor level with audio visual indication for pump on facility complete as required

Providing , laying , testing and commissioning of PVC insul

ated , copper conductor , 1100 V grade , armoured cable of following sizes between metering panel at ground floor and pump set main electric panel at terrace level and push buton switch at ground floor level including PVC pipe , suitable clamps etc. where required and conncetions at panel and push button switch complete as required , as specified and as directed by Engr-in-charge

Providing and fixing 80mm dia , Class - 1 butterfly valve conforming to type PN - 1,6 of IS 13095-1991 complete with flanges , bolts , nuts , gasket etc. as per specifications complete in all respect , hydraulically tested to 20kg / sqcm , complete all as specified and as directed by Engr-in-charge .

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts , luminous efficacy not less than 110 lumen/wattwith pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge.

M & L for earthing complete with galvanized earth plate electrode 600mmx 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvenised earth lead wire of 4 mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 3 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work PCC(1:3:6) type C-1 pit with precast RCC Cover slab 40 mm thick in PCC(1:2:4) type B-1 reinforced with 6 mm dia MS bars @ 100 mm c/c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe and 15 mm dia GI pipe for protection of GI wire up to 7.5 mtr connected to earthing point complete all as specified and as directed.

Item No 40 : Sign of size 300 mm X 150 mm reading 'EXIT' in 12.5 mm block letters in Green and white background, properly spaced to provide good legibility located directly in corridor near to each staircase and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part XII

Providing and fixing cast iron double flanged horizontal type with gunmetal seat non - return valve conforming to class - 1 of IS : 5312 including nuts , bolts , 1.5 mm thick compressed asbestors gasket including painting of following size complete all as specified and as directed by Engr-in-charge

(b) 100 mm dia

Providing and fixing cast iron double flanged horizontal type with gunmetal seatSulice valve Class PN 1.6 valve conforming to class - 1 of IS : 5312 including nuts , bolts , 1.5 mm thick compressed asbestors gasket including painting of following size complete all as specified and as directed by Engr-in-charge

(Lightning Protection)

Supply and fix single pointed air termination aluminium rod, 12 mm dia, 300 mm long complete all as specied.

Supply and fix aluminium strip 25mm x 3 mm complete with saddles and fixing screws for fitting the strip complete all as specified. (as roof conductor)

Sch 'A' Part-VII (Sewage Disposal) Lump sum price worked out by the contractor for 'Sewage Disposal', excavation & earth works' as listed in Schedule 'A' Part-VII against the lump sum price inserted by the MES.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part XIII

F. AMF PANEL The control panel shall be made of CRCA sheet duly fabricated and powder coated and complete with internal wiring, bus bar etc and fitted with the following accessories :- (i) MCCB 4 Pole 160 Amps 25 KA Microprocessor release type – 02 Nos (ii) Contactor 160 Amps -02 Nos (iii) Digital Ammeter with CT of size 200/5A – 02 Nos (iv) Digital Voltmeter 3 Ph 415 volts – 02 Nos (v) Indicating lamps (LED type) (R-Y-B) – 02 sets (vi) Relay, timmer and other acessories as per manufacturer.

(xiii) Battery charging alternator (xiv) Engine control panel consisting with ON/OFF Start Key,Lub oil pressure guage, Battery charging ammeter,Coolant temp gauge, RPM Meter etc. (xv) Suitable flexible coupling (xvi) Front & Rear engine mounting supports (AVM pads)

Total carried over to BOQ Rs.

Signature of Contactor

(Internal Water Supply)

(Rain Water Harvesting)

Supply only water proofing compound (Liquid) complete all as specified and as directed.

M&L cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm dia in bed to drain pipes including packing under, and completely surroundings of pipes etc complete all as specified and as directed

M&L TMT bars 10 mm dia , cut to length, bent to shape required, including crancking, bending spirally for hooping for columns ,hooking ends & binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & as directed.

M&L for brick work sewer bricks straight or curved on plan exc 6 m mean radius for man-holes/septictank/ soakwell etc in sewer works built in CM 1:4 etc complete all as specified and as directed

M&L for PCC 1:4:8 type D2 using 40mm graded aggregates in foundation filling and mass concrete as in lean concrete

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc all as specified.

Sewage Disposal

M&L for brick work with fly ash brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation etc for for shafts, wells cesspits, manholes, piers holes etc not exceedin 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard/dense soil etc complete all as specified and as directed

Total carried over to BOQ Rs.

Signature of Contactor

Internal Electrification

(Demolition of Bldg)

Demolition of brick work / stone boulders masonry built in cement mortar incl all Quoins , archeas, pillars etc but exc cluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling framed trusses span n exc 10 m complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Taking down Chowkhats or frames without taking of shutter from frame not exc. 1.5 sq. m each incl all iron mongeries complete all as specified and directed.

Taking down Chowkhats or frames without taking of shutter from frame exc. 1.5 sq. m but n exc 4.00 sq.m each incl all iron mongeries complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

Total carried over to BOQ Rs.

Signature of Contactor

Item No 01 : Supply and fixing 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 Amps and current carrying capacity in the MCB DB complete with connection testing and commissioning connection with suitable size aluminium / copper lugs complete all as specified and directed.

(SITE CLEARANCE)

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil all as directed

Excavation over area n.exceeding 1.5 m deep and getting out in soft /loose soil

Removal of excavated material exc 250m but n exc. 500m and depositing where directed.

Grubbing up tree trunk girth exc 100cm and n.exc 150cm including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site

Grubbing up tree trunk girth exc 150cm and n.exc 200cm including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site

Total carried over to BOQ Rs.

Signature of Contactor