Repair and renovation of office cum chamber of the Judge, Family Court, Port Blair under SD-II, PBSD, APWD, Port Blair.

Amount

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 600x600 mm

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hours. 3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes.grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done and this surface is further allowed to dry for 12 hrs. 4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:

One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Providing and fixing hand shower (health faucet) with 8mm dia, 1.2 mtr long flexible tube & wall hook of make Jaquar (code - ALD-CHR-573) or its equivalent.

Providing and fixing Single towel rail 600mm long, stainless steel (code No. ACN-1111SM) make Jaquar or its equivalent.

Providing and fixing Towel ring square (code-AKP - 35721P) and complete with brackets fixed to wooden cleats with brass screws with concealed fittings arrangement of approved quality and colour of make Jaquar or its equivalent.

Providing and fixing C.P. brass bib cock of approved quality of make Jaquar ( No. CON - 037 KN) or equivalent.

15 mm nominal bore

Providing and fixing glass shelf 600 mm wide of make Jaquar ( No. ACN - 1171 N) or equivalent.

Providing and fixing Soap Dish Holder of make Jaquar ( No. ACN - 1131 N) or equivalent.

Providing and fixing pillar cock of aprroved quality. (Jaquar or equivalent make code No. (Code No.CON -011 KN).

15 mm nominal bore

Providing and fixing Angular Stop cock continental of approved quality of Make Jaquar (Code No.CON-053KN) or equivalent.

15 mm nominal bore

Providing and fixing C.P. Brass Towel rack 600 mm long with bracket fixed to wooden cleat with CP brass screws with complete fitting arrangements of approved quality and colour of make Jaquar (No. ACN 1181 FN) or equivalent.

Providing and fixing Toilet Paper Holder (No. ACN-1151 N) make Jaquar or equivalent.

Providing and fixing wash basin of make Jaquar (Code CNS - WHT - 801) or equivalent with full pedestal of make Jaquar (Code CNS - WHT - 301) including making all connections as per the direction of Egnineer-in-charge.

Providing and fixing EWC 'S' Trap (Code No. LYS WHT-38751S250UFSM) with internal fittings, Seat Cover, Cistern (Code No. LYS WHT 38201) etc. all complete. Make : Parryware, Indus range, Jaquar or equivalent.

Providing and fixing 100 mm square sand cast iron grating for gully trap.

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length 20.1.1) 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing two way Bib Cock with wall flange of approved quality : (make Jaquar FLR-CHR-5041N) or equivalent as desired by the Engineer in charge.

B M SINGH