REPAIR TO STONE MASONRY, ROOFING, FLOORING, PLASTERING, JOINERY, CEILING, CUPBOARD, WRITING TABLE, WINDOW GLASS AND OHT IN CERTAIN UNITS AT ZONE -I AT MIL STN JAISALMER

Amount

Demolition of Brick or stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified & directed by Engineer-in-charge.

All as per item No. 2 hereinbefore but except stone. Note :- Serviceable stone obtained from Ser Item No.1 herein before shall be used.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified.

M&L for keyed pointing in cement mortar (1:4) to squared rubble masonry, Jodhpur type, coursed or un coursed all as specified & directed by Engineer-in-charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified & directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed by Engineer-in-charge.

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters complete confirming to Fe 410-W (Gde E-250 quality-A) complete all as specified & directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

S&F glazed ceramic coloured tiles of size 450mmx300mmx 7mm thick (Joint free) on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in CM (1:4) all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed.

M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified & directed.

M&L for non skid ceramic coloured tiles (Joint free) of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed.

M&L for virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed.

M&L for non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over including screed bed or bedding layer of 16mm thick in CM (1:6) complete all as specified & directed.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring/ hard standing path & finishing the surface even & fair without using extra cement all as specified & directed.

M&L for 60 mm thick, M-35 grade, rubber moulded, machine pressed precast concrete inter locking paver block using no pigment, confirming to IS 15658-2006, shape & size as approved by GE, laid over and including 25mm thick sand cushioning complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed inclusive of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) packing and finished even and fair to the sides of pavement.

Dismantling stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified & directed by Engineer-in-charge.

M&L sand stone slabs 5cm thick in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar (1:2) or cement mortar (1:4) complete all as specified & directed by Engineer-in-charge.

M & L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types complete all as specified & directed by Engineer-in-charge.

Dismantling boarding of any description fixed in any position fixed with screws complete all as specified & directed by Engineer-in-charge.

S & F 18/19mm thick pre-laminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination alround 6mm th teak fillets fixed in kitchen CB or pelmet complete all as specified & directed by Engineer-in-charge.

M&L for 2nd class hard wood fillets square, rectangular as in lippings fixed with nails of area exc 3Sqcm but n.exc 6sqcm complete all as specified & directed by Engineer-in-charge.

S&F 40mm width of flaps (when open) continuous (piano) hinges, mild steel bright finish or Electro galvanised fixed to wooden or angle iron frame complete all as specified & directed by Engineer-in-charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-charge.

S&F 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws /fixed in repairs complete all as specified & directed by Engineer-in-charge.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkat (without taking of shutter from the frame) exceeing 1.5 Sqm and not exceeding 4 Sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 and painting to match with the surface ccomplete all as specified & directed by Engineer-in-charge.

M&L for Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed by Engineer-in-charge.

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified & directed by Engineer-in-charge.

S&F Sheet glass, 4.80 mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified & directed by Engineer-in-charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty approved by Engr-in-Charge

S&F aluminium (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified & directed by Engineer-in-charge.

S&F 3mm thick frosted glass in squares not exceeding 0.5 Sqm with glazing clips and oil putty including hacking out old broken glass of any thickness size,quality or description from metal frames complete all as specified & directed by Engineer-in-charge.

Taking down cement plaster on brick/stone/concrete surface including wall tiling or terrazo finish and hacking out joints hacking for key scrubbing down with water etc complete all as specified & directed by Engineer-in-charge.

M&L rendering 15 mm thk on brick or concrete surface in CM (1:6) and surface finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement morter (1:4) on fair face of brick wall or concrete surfaces, finished even & fair complete all as specified & directed by Engineer-in-charge.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of cement primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of any description and applying two coats of oil emulsion distemper over a coat of primer including wall putty for making uniform smooth surface complete all as specified & directed by Engineer-in-charge.

S&F GI tubing (ISI) marked) medium grade with all fitting and fixed complete to wall ceiling or laid in floors of 15 mm bore size including taking down existing steel water tubing complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI) marked) medium grade with all fitting and fixed complete to wall ceiling or laid in floors of 20 mm bore size including taking down existing steel water tubing complete all as specified and directed by Engineer-in-charge.

S&F in repair, anodised aluminium alloy curtain rails plastic coated incl fixing brackets, 2 Nos side cups etc complete all as specified & directed by Engineer-in-charge.

BHAGWATI CONSTRUCTION

S K TRADER

Leelashah Enterprises