SPL REPAIRS TO BLDG NO NP56 JCO MESS AND PROVN OF DRAIN AND SEWAGE LINE FOR BLDG NO P83 AT 203 CEDU AND OTHER PROVN WORKS UNDER GE SOUTH UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each and removing to store complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4 sqm each and removing complete all as specified.

Taking down cement plaster of any descreption on brick/stone walls or concrete surfaces including racking out joints, hacking for key scrubbing down with water etc on walls and ceiling, complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precastconcrete articles complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified.

Dismantling structural steel work including doors, gates including framed truss etc. complete all as specified.

Dismantling wall & ceiling boards of any description and thickness including cover fillets, complete all as specified and directed.

M&L prepainted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick in camoflange pattren having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

M&L prepainted galvalume aluminium zink coating GI based plain steel sheet 0.50mm thick nridge ,hips ,valley gutters at the external end slope of camoflange pattren colour having tensile strength of 550Mpa fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

10-12 mm thick gypsum boards seamless false ceiling as approved, moisture resistant, including GI hanging wires, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying 1 to 1.2mm thick Altek/Birla white putty to obtain smooth/even finish using sand paper and applying two coats of distemper oil emulsion over a coat primer on boards surface etc complete all as specified and directed by Engr-in-charge

Light shade double charged vitrified tile 10 mm thick (Square / rectangular) polished , area of each tiles not exceeding 0.36 Sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or beddding layer in cementy mortar 1:4 complete all as specifed and as directed.

Ditto all as per item above but as in skirting over vertical surfaces & including 10 mm thick cement mortar 1:4 screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tiles complete all as specified and directed by Engr-in-Charge.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

8mm thick Toughned glass (tinted glass one side view) as in windows, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed.

Granite stone 18-20mm thick (table rubbed and polished) in window cills, cooking platforms and the like not less than 1 Sqm (in one piece), laid over 15mm thick layer of cement mortar 1:3 after roughening of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including demolition of stone slabs and tiles of any description or thickness in floors etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

S&F Mild steel Frame as in purlins, crane gantries, rails ,cabinates frmaes and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance Pieces, cleats etc Fe 410 - (Gde- E- 250) quality- A , etc complete all as specified and directed by Engr-in-charge or Garrison Engineer.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bar aluminium section weighing 0.55 kg/m including necessary joining cleat , glazing clips, rubber packing, frosted glass 4mm thick, anodised aluminium snap beading screws , anodised aluminium fitting such as peg stays 150mm long (1 no) hinges type B-12 100mm long (2 no ) suitable handle (1 no) etc complete all as specified.

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:6 including demolition of old brick/stone masonry complete all as specified and as directed.

M & L for PCC 1:2:4 Type B-1 using 20 mm graded aggregate in surface channels and drains complete all as specified.

M&L for cement concrete type B1 1:2:4 (using 20 mm gradded aggregate) use in coping, hold fast and similar work including naccesary form work complete all as specified and directed.

M & L Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces fair and even without using extra cement all as directed

M & L Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:6) including finishing the surfaces fair and even without using extra cement all as directed

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified.

M&L for 75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified and directed.

S & F in repair 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F in repair 15mm bore stop valve/angle cock, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified.

S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repair Soap dish holder incl all fittings complete all as specified.

Vitreous china,white, wash hand basin, flat back of size 550x400mm, white including MS brackets and pedestal pattern including cutting for and pinning including 32mm dia CP brass waste coupling and PVC waste pipe, fixed in repair complete all as specified. Make-CERA cat part No. S 2040105 for WHB & for pedestal cat part No.S 2090101, Jaquar- SLS-WHT-0611F for WHB and SLS-WHT-1510 for pedestal or Hindware approved make as approved by GE.

S&F PVC connection 15 mm dia and 600mm long with two Nos of brass check nuts and washers complete all as specified.

S & F 15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

S & F 20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

M & L for 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tank and removing from site complete all as specified.

S & F in repair of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends for iron pipe of size 20mm bore complete all as specified.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, and connecting waste pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engr In charge.

Stainless steel plate rack made out of 0.63mm thick steel sheet, minimum size 600 x 750 x 250mm of standard quality and shape, fixed in repairs complete all as specified and as directed. Make: Prayag Cat Pt No P-330 or equivalent of Jayna/ Neelkanth/Nirali.

Harrison rails,mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all specified & directed.

S&F 75 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F 75 mm PVC (SWR) bends any redius with access door complete all as specified and as directed.

S&F PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good all as directed

M & L for RCC 1:2:4 type B1 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed

S&F TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9mm dia or securing with clips quality conforming complete all as directed.

M&L for form work to soffits of suspended slabs and similar work not exceeding 200mm thick complete as specified and as directed.

S&F 600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screwscomplete all as specified.

M & L for applying 1 mm thick layer of wall putty on walls to give uniform surface, surface scrubed with emery paper and make surface good and clean complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M & L for preparation of new plaster surfaces of walls/ceiling and applying two coats of oil emulsion distemper (white/tinted) all as specified.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level, complete all as specified and directed by Engr In charge.

M&L for 75 mm thick pcc type C-2 1:3:6 , using 40mm graded crushed stone aggregate as in sub base for receiving floor finishes finished even and fair complete all specified and as directed.

M&L for 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM 1:4 complete all as specified.

M&L for Dura stone haeavy duty vitrified tiles of size 300 x 300mm x8-10mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface, complete all as specified and directed by Engr In charge.

M & L for Chequered cement concrete tiles 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with mixture of white and grey cement in equal proportion & no pigments including 15mm thick screed bed in cement mortar 1:6 complete all as specified.

Removing excavated soil/debaries to a distance exc 50m and nexc 1.5 Km and depositing at level n exc 1.5m above the starting point , Including debris all as specified and directed by Engr -in -Charge.

Demolition of brick/stone masonry built in CM. complete all as specified and directed by Engr In charge.

Excavating in trenches not exceeding 1.5m wide and n.exceeding 1.5m in depth; for foundation etc or similar work and gating out in any type of soil all as specifed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed by Engr In charge.

M&L for plain cement concrete1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed.

M&L PCC 1:2:4 type B0 (12.5mm graded aggregate) as in coping, benching and similar work etc including necessary form work complete all as spcified and directed.

M & L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as in drain, walls and similar work etc complete all as specified and as directed.

M & L Rendering 15mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces even and smooth without using extra cement as in drain etc and similar work all as directed

Returning filling in including spreading levelling watering and well ramming in layers not exc 25cm all as directed

Removing excavated soil to a distance exc 50m and nexc1.50 km dout side defence land all as directed, complete all as specified and directed by Engr In charge.

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out of soft/loose soil complete all as specified.

M&L hardcore of broken bricks gauge n exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled /rammed to true surfaces complete all as specified

M&L for 50 mm thick PCC type D-2 1:4:8 , using 40mm graded crushed stone aggregate as in sub base for receiving floor finishes finished even and fair complete all specified and as directed.

M&L for coloured chequered cement concrete tiles 30cmx30cmx25mm , machine pressed; set jointed and pointed in neat cement slurry in floors, with grey cement and pigments laid over 15 mm thick screed bed in CM 1:6 complete all as specified.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate), kerbs including chamfers, weathering etc, on edges of roads/paths complete all as specified and directed.

M & L for providing Precast RCC 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for manholes etc.), chajjas, shelves and similar articles with plain faces set in CM 1:4 complete plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match complete all as specified.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified .

M & L for applying two coats of synthetic enamel ordinary tint paint including red oxide primer and preparation extra complete on new steel or iron surfaces of any description, over 10cm in width or grith, not otherwise described complete all as specified.

S&F TMT bars 6-8 mm dia and over, cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9mm dia or securing with clips quality conforming complete all as directed.

M&L for 300 mm dia reinforced concrete pipes, class NP-2 laid and jointed complete with collars. Complete all specified and directed.

M&L cement concrete type D-2 1:4:8 for concrete bed to 300 nmm dia RCC drain pipe including packing under , and haunching against the sides of pipes after they are laid & testing, complete all as specified and directed by Engr In charge.

M & L for 150 mm dia SGSW pipe laid in trenches and jointed complete with collars complete all as specified and as directed.

M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as directed.Keeping the LED lights in safe custody.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unsv MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specified and directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly including cutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed. Make: Havells/ Finolex/ Polycab.

All as per item no 85 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on an independent board, complete all as specified and directed by Engr In charge.

All as per item no 85 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on the same board with other switch, complete all as specified and directed by Engr In charge.

All as per item no 85 above but for one 3/6 pin 16 amps socket outlet point on an independent board with cables of size 2.50 sqmm, complete all as specified and directed by Engr In charge.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge. Make- Havells Crabtree/Legrand/ Schenider/L&T

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge. Make- Havells Crabtree/Legrand/ Schenider/L&T

S & F modular Bell push flush type 6 amp 230 V, 50 Hz, AC,with outer/inner cover complete all as specified and directed by Engr In charge. Make- Havells Crabtree/Legrand/Schenider/L&T

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC,with outer/inner cover complete all as specified and directed by Engr In charge. Make- Havells Crabtree/Legrand/Schenider/L&T

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC,flush type with outer/inner cover complete all as specified and directed by Engr In charge. Make- Havells Crabtree/Legrand/Schenider/L&T

M &L Ceiling rose, surface bakelite 65x 50mm three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge. Make- Havells/Legrand/Schenider/L&T

S & F calling Bell ding dong 230 volts single pole 50Hz complete all as specified and directed by Engr In charge

S & F for electronic step type fan regulator 100 watt 2 module 230 volts 50hz deluxe modular type complete all as spcified and directed. Make- Havells Crabtree/Legrand/Schenider/L&T

S&F single pole and neutral enclosure surface mounted 240 volts with 3/5 pin and earth plug and socket with one single pole Modular MCB 20 Amps and Plug top with indicator complete all as specified and directed.

S&F in replacement 36W(2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination, complete all as specified and directed by Engr In charge. Make - Syska/Philips/Bajaj

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type warm white colour with driver,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr In charge. Make-Syska/Philips/Bajaj

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type daylight/warm white colour with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr In charge. Make-Syska/Philips/Bajaj

Supply and fixing LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed by Engr In charge. Make-Syska/Philips/Bajaj

S&F of decorative wall mounting 1X9W fixture with frosted glass along withB-22 holder & 9W warm white bulb/GLS lamp luminaire complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosure double door type for MCCB TPN DB upto 100 Amps,16 KA , 4 way vertical type 415 volts with suitable rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make-Havells/Legrand/Schenider.

S & F replacement MCCB Three Pole & Neutral capacity of 100 amps 415 volts rupturing capacity 16 KA all as specified and directed by Engr-In-charge. Make-Havells/Legrand/Schenider.

S&F Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately) Make-Havells/Legrand/Schenider.

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA,inculding providing thimble for out going cable, complete all as specified and directed by Engr In charge. Make-Havells/Legrand/Schenider.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable, complete all as specified and directed by Engr In charge. Make-Havells/Legrand/Schenider.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified & Directed By Engr-In-Charge.Make- Havells/Finolex/Polycab

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 10 Sq mm as earth lead all as specified. Including taking down old sub main wire, complete all as specified and directed by Engr In charge. Make- Havells/Finolex/Polycab

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X1.5 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 1.5 Sq mm as earth lead all as specified. Including taking down old sub main wire, complete all as specified and directed by Engr In charge. Make- Havells/Finolex/Polycab

khajuria builders (BID ID -3361650)

RAMAN CONSTRUCTION CO (BID ID -3362587)

anil construction co. (BID ID -3361179)

SINGH CONST CO (BID ID -3361400)

paras ram pachiala (BID ID -3360172)

M/S Ashok Kumar Jaswal (BID ID -3360876)

RAJ MOHD (BID ID -3362490)

AKBAR FURNITURE HOUSE AND TIMBER MERCHANT (BID ID -3361008)

M/S PARDEEP KUMAR (BID ID -3361729)

M/S R S Builders (BID ID -3355950)

M/S IMRAN MAJID (BID ID -3361751)

PARDEEP SHARMA (BID ID -3362376)