Renovation and Interior Fit-Out Works of SIDBI Office, Bahadurgarh, Haryana

14.00 Grand Total 37,94,633.00

CERAMIC TILE FLOORING :- Providing and laying rectified Glazed Ceramic

floor tiles of size 300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of approved make, in

3.1 11.40 all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 SQM 10.00 1,439.40 14,394.00

mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement

and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy

grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of

3.2 11.48 hardener and 0.20 kg of resin SQM 10.00 373.35 3,733.50

per kg), including filling / grouting and finishing complete as per direction

of Engineer-in-charge.

11.48.1 Size of Tile 500x500 mm

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different

sizes (thickness to be specified by the manufacturer) with water absorption

less than 0.08% and conforming to IS: 15622, of approved make, in all

colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4

11.41A coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and matching pigments etc.,

INSULATION- Providing and fixing thermal insulation with Resin Bonded

rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm

thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel

3.4 12.62 plug & washers and held and in position by criss cossing GI wire etc. SQM 40 322.50 12900.00

complete as per directions of Engineer-in-Charge.

4 PARTITIONS AND WALL CLADDING

PANELLING- Providing and fixing wall panelling using 12mm thick plywood

fixed on one side of aluminium frame of size 50mm x 25mm x 1.5mm, as per

approved sample and architectural drawings. Aluminium frame to be fixed

to wall, floor, and RCC ceiling using suitable fasteners. Work to include all

necessary materials, labour, tools, fasteners, adhesive, screws, supports, and

complete in all respects.

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF,

on an existing Plywood surface.

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

Providing and fixing partition using 12mm thick plywood fixed on both sides

on aluminium frame of size 50mm x 25mm x 1.5mm as per approved sample

4.3 MR and architectural drawings. Aluminium frame to be fixed to wall, floor and SQM 50.00 3,970.12 1,98,506.00

RCC ceiling using approved fasteners including cutting, jointing, finishing,

screws, adhesive, etc., complete in all respects.

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double acting hydraulic floor spring type fixing

4.4 21.18 arrangement and making necessary holes etc. for fixing required door SQM 79888.50

fittings, all complete as per direction of Engineer in charge (Door handle,

lock and stopper etc. to be paid separately)

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling

height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling

channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable

anchor fastener or metal screws with nylon plugs and the studs 48

mm wide having one flange of 34 mm and other flange 36 mm and

0.50 mm thick fixed vertically within flanges of floor and ceiling

4.5 9.105 channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed

flush to wall with suitable anchor fastener or metal screws with nylon

plugs at spacing of 450 mm centre to centre, and fixing of boards to

both side of frame work by 25 mm long dry wall screws on studs, floor

and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to

avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm

thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at

corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of

primer suitable for board as per manufacture's specification and

direction of engineer in charge all complete.

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

9.105.1 75 mm overall thickness partition with 12.5 mm thick double skin fire

5 rated Glass Reinforced Gypsum (GRG) SQM 22 2,131.10 46884.2

plaster board conforming to IS: 2095:

GYPBOARD CEILING :- Providing and fixing false ceiling at all height

including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200

mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5

mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the

angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm

with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing perimeter channels 0.5

mm thick 27 mm high having flanges of 20 mm and 30 mm long.

Including jointing and finishing to a flush finish of tapered and square

edges of the board with recommended jointing compound , jointing tapes

, finishing with jointing compound in 3 layers covering upto 150 mm on both

sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making

openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the

cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

Providing and fixing mineral fibre false ceiling tiles at all heights of size

595X595mm of approved texture, design and pattern. The tiles should

have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%,Thermal

Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6

&7)in true horizontal level suspended on interlocking T-Grid of hot dipped

all round galvanized iron section of 0.33 mm thick level suspended on

interlocking T-Grid of hot dipped all round galvanized iron section of 0.33

mm thick5x32mm of length 1200 mm and secondary intermediate cross T of

size 15x32 mm of length 600 mm to form grid module of size 600x600 mm

suspended from ceiling using galvanized mild steel item

(galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6

mm diameter fully threaded hanger rod up to 1000 mm length and L-shape

level adjuster of size 85x25x2 mm, spaced at 1200 mmcentre to centre

5.2 26.27 along main ‘T’. The system should rest on periphery walls /partitions with the

help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm

thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm

centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom

portion of all T-sections used in false ceiling support system shall be pre-

painted with polyester baked paint, for all heights. The work shall be carried

out as per specifications, drawings and as per directions of the engineer-in-

With 15 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.5)

6 DOORS/ WINDOWS

DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position with hold

6.1 9.1 fast lugs or with dash fasteners of required dia & length ( hold fast lugs or

dash fastener shall be paid for

9.1.1 Second class teak wood CUM 0.25 142949.7 35737.425

FLUSH DOOR:- Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board construction

6.2 9.21 with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters :

35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

Extra for Providing and fixing flush doors with decorative veneering instead

6.3 9.22 of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part

9.22.1 On one side only SQM 2.50 478.00 1,195.00

Extra for providing lipping with 2nd class teak wood battens 25 mm

6.4 9.23 minimum depth on all edges of flush door shutters (over all area of door SQM 2.50 462.35 1,155.88

shutter to be measured)

Providing and fixing wooden moulded beading to door and window

6.5 9.40 frames with iron screws, plugs and priming coat on unexposed surface etc.

9.40.1 2nd class teak wood

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular

Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked,

6.7 9.97 anodised (anodic coating not less than gradeAC 10 as per IS : 1868 ),

transparent or dyed to required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type

floor door stopper with necessary screws, etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame

with 10 mm diameter bolts, nuts and wooden plugs and embedding in

6.9 9.53 cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 EACH 6.00 228.85 1,373.10

graded stone aggregate 20mm

6.10 MR Door Closer:- Providing and Fixing Door Closer For Entry Door EACH 3.00 1850 5550

Providing and Fixing ESDH 22x450 mm D-type Handle Material : Stainless

Steel. Finish : Satin Stainless Steel (SSS). of approved make and model all

6.11 MR complete as per the direction of Engineer-in-charge. Each 4.00 3450 13800

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for door thickness

6.12 MR 25-50 mm for of approved make and model all complete as per the Each 4.00 750 3000

direction of Engineer-in-charge.

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

Providing and Fixing FH-943 Double cylender Floor Spring- with Closing

Force EN 3 with Maximum door weight 105 Kg. Maximum door width

950mm.Closing speed : 130°

Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of

6.13 MR floor spring approx : 6kg, 5,00,000 cycles Tested with 5 Years Warranty Each 4.00 8000 32000

against manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom Strap of approved

6.14 MR make and model all complete as per the direction of Engineer-in-charge. Each 4.00 2065 8260

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key Hole of

6.15 MR approved make and model all complete as per the direction of Engineer-in- Each 4.00 1650 6600

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive

vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass

with customised designs, thickness of 2 mil (0.05mm) without adhesive &

3mil (0.8)with adhesive having minimum tensile strength of 3.5

pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of

installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass

6.16 MR Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to SQM 30 1650 49500

15yrs (indoors) must be endorsed by 3M India Limited Architectural

Market Department. Contractors payment wouldn't be released until &

unless he/she produces orginal warranty certificate from the manufacturer.

7 FINISHES & MISCELLANEOUS

Wall painting with acrylic emulsion paint, having VOC content less that 50

7.1 13.82 grams / litre, of approved brand and manufacture, including appliying

additional coats wherever required, to achive even shade and colour.

Providing and applying plaster of paris putty of 2 mm thickness over

plastered surface to prepare the surface

Applying priming coats with primer of approved brand and manufacture,

7.3 13.85 having low VOC (Volatile Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood)

having VOC content less than 50 grams/ litre

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm BWP

Ply Board finished using 1mm thick Laminate. The storage to be complete

with all hinges, drawer glides and hardware from approved make. All

7.5 M.R. internal surfaces to be completed using balancing laminate. Including sqm 8.00 13,500.00 1,08,000.00

brass D-type handles for shutters and recessed type handles for drawers or

as approved. Storage to be of all heights as per design. Storage shutters to

be made in solid laminate/ glass as per design and drawings.

7.6 Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity

counters, window sills, facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high gloss finish etc. complete at

8.2.2 Granite stone slab colour black, Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm sq.m 3 5,136.30 15,408.90

7.7 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen

sink in kitchen platform, vanity counter and similar location in marble/

Granite/ stone work, including necessary holes for pillar taps etc. including each 1 978.70 978.70

moulding, rubbing and polishing of cut edges etc. complete.

Digitally signed by AMIT

Sl. No. DESCRIPTION UNIT QTY AMOUNT MARKET RATE AMOUNT

Ref. No. (DSR 2023)

BLINDS Providing & supplying of Window Blinds as per the approved

sample in required shade and style consisting, of ZEBRA BLINDS comprising

of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric

weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18-

19/cm, having fire resistance standard – NFPA 701-89 small testing ISO- 5659-

2 .Thetear resistance should be complying to ISO4674 & breaking resistance

– ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe

installation, moulded plastic with steel spring support and inserted into the

tube end. It shall be driven by a ball chain pulley with ball chain and can

be positioned at right side or left hand side of the Shade. The Shade when

lowering or raising, shall be automatically locked in position upon release

of the ball chain by means of a built in friction lock.Universal clutch for left

and right hand operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be

7.8 M.R. molded of plastic witha steel location pin.The plug shall be inserted into the SQM 20.00 1,650.00 33000

tube end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT

BRACKETS shall be of coated steel & provided with covers and used in right

hand or left hand positions differentiated by the acceptance of the of the

rectangular drive unit support or the round idler plug pin.Can beinstalled

(a) On Face (b) Ceiling Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal

diameter & skin thickness of 1mm and shall incorporate a key way integral

with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat

Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm

diameter cord with 4.5mm diameter acetal balls moulded co-axially to it

on 6mm pitch to form an endless ball chain. It is used for raising

Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or

equivalent of approved make with 100% Nylon and completely water proof

resilient backing. The flooring should be Anti static with thickness of 4.3 mm

and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be

completely stain resistant and of a density approx. 80 million fibers/sq.mtr

(70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have

Fire Test EN-13501, Appearance Retention Hexapod ISO 140- 8, Friction Slip

Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with

7.9 NS resilient waterproof backing, anti allergic which is certified by British allergy sqm 12.00 1,650.00 19800

foundation, with ten year replacement guarantee. The carpet should

have permanent static control & should be fixed with powder coated

aluminum angles as per detail. Aluminum angles to be paid separately.

Providing & fixing of 3mm thcik vinyl flooring as per sample approved cost

including wastage and fixing charges completel

SUB TOTAL OF FINISHES 5,14,883.04 8,80,752.62

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO TOTAL AMOUNT TOTAL AMOUNT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

A.1 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface

A.2 / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core

A.3 1.12 cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC Metre 70 334.00 23,380.00

insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 32 122.00 3,904.00

1.24.5 6 pin 15/16 amp socket outlet Each 12 197.00 2,364.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC

conduit as required

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 150 334.00 50,100.00

Digitally signed by AMIT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 439.00 8,780.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 10 1005.00 10,050.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 20 1365.00 27,300.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

C.2 Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured

cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(e) 3.5 C x 35 Sqmm XLPE cable RM 20 850.00 17,000.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper

C.3 MR conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 10 1850.00 18,500.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 0 2140.00 0.00

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

breaker suitable for inductive load of following poles in the existing MCB DB complete with

D.2 connections, testing and commissioning

etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB

DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 1 9081.00 9,081.00

Digitally signed by AMIT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes

in the existing MCB DB complete with connections, testing and commissioning etc. as

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate & switch

E.7 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 1 148.00 148.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

insulated, shielded with fine tinned copper braid and protected with PVC sheath in the

exisitng surface/recessed steel/ PVC

conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with

E.13 connectors suspended from the cieleing with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 10 1137.00 11,370.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering

pipe of 2.7 metre long etc. with

charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 15 70.00 1,050.00

Total of Electrical items 447272.98 44581

GST Multiplying factor @ 1.0633 on Electrical DSR 2022 for GST 12% to 18% 4,75,585.36 44581

Modfied factor of GST on DSR @ 0.973 for considering GST @ 18% instead of 21.27 % - 4,62,744.55

Digitally signed by AMIT

1.0 Description Unit Rate Total Qty DSR Amount

Ref. No. Amount

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall

split type Air conditioners complete with Indoor unit(IDU), Out door

unit (ODU), surface / concealed copper Refrigerant piping with

insulation (closed cell elastomeric nitrile rubber tubular pipe section)

upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to

ODU) i/c drain pipe R-32/R-410/ R- 407 Green refrigerant, wireless

Remote control, suitable for working

between 180-260V with low & high voltage cutoff and 50 hz ,1

phase AC supply capable of performing cooling, dehumidification,

air circulation of following capacity with Scroll / rotary compressor.

The system shall be able to deliver 100% of the rated capacity upto

42 Degree Celsius. Min 5 year Original Equipment Manufacturer

(OEM) warranty both compressor and

Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or

IS 9968 temperature sensing control IS /International Electro

technical Commission (IEC) 60730, hermetic compressor IS 10617,

heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615.

Complete as per CPWD specification and IS : 1391 Part II 2023. The

system shall be able to operate up to 50 0C (out door ambient

Inverter Type - Cooling only

8.2.2 1.0 TR with 5 Star BEE Rating Each 39196 1 39196

Digitally signed by AMIT

1.0 Description Unit Rate Total Qty DSR Amount

Ref. No. Amount

Supply, Installation, Testing and Commissioning of Air Cooled

Cassette type Air conditioners complete with Indoor unit(IDU), Out

door unit (ODU), R- 32/R410A/R-407 Green Refrigerant, wireless

Remote, inbuilt drain pump, suitable for 400/230V, 50 Hz ,1 /3 phase

AC supply, including surface / concealed copper Refrigerant piping

with insulation (closed cell elastomeric

nitrile rubber tubular pipe section) upto 5.5 Mtr (IDU to ODU), copper

power and control cable upto 5.5 Mtr (IDU to ODU) including drain

pipe, the system shall be capable of performing cooling,

dehumidification, Air circulation, filtration & ventilation of following

capacity with Scroll/rotary compressor with min 5 year Original

Equipment Manufacturer (OEM) warranty both

compressor and Printed Circuit Board (PCB) as specified. The system

shall be able to deliver 100% of the rated capacity as per relevant IS

Code. The lab testing reports as per IS: 1391 shall be submitted from

National Accreditation Board for Testing and Calibration

Laboratories (NABL) accredited as per International Electro

technical Commission (IEC) 17025 standards / Central Power

Research Institute (CPRI)/Electrical Research

and Development Association (ERDA)with Original Equipment

Manufacturer (OEM) etc. complete as per CPWD specification and

as per IS: 1391 as required.

Inverter Type- Cooling only

8.4.1 1.5 TR with 5 Star BEE Rating Each 67095 3 201285

8.4.4 3.0 TR with 5 Star BEE Rating Each 107192 1 107192

3.0 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

3.0 7.14 supports, jointing/brazing including accessories, insulated with XPLE

Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick

insulation as given below for Suction and Liquid lines, all accessories

as per specifications etc. as required :

Digitally signed by AMIT

1.0 Description Unit Rate Total Qty DSR Amount

Ref. No. Amount

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

19.0 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19

mm thick insulation

4 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe

,complete with fittings, supports,U trap arrangement,Clean Plug with

6mm nitrile insulation and accessories as per specifications,

Providing and fixing control cum transmission wiring of 2 core x 1.0

4.3 MR sq. mm copper in suitable conduits between indoor and outdoor Mtr 161.6 130.00 21,008.00

Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp

Supply and fixing MS base frame for VRV outdoor stand as per

Total Amount 452818 50017

Total Amount 452818 50017

Digitally signed by AMIT

S No Description UNIT Qty RATE

A. UTP Components for Data DSR (INR)

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors for

1 Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250 MHz, Mtr 450 57.00 25650.00

1.53.1) Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6 cable termination at

Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

3 for information outlet (I/O) to end user device connectivity.High Speed Gigabit Nos. 20 275.00 5500

24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 1 Mtr (3 feet) for

4 information outlet (I/O) to Rack End Redantant device connectivity.High Speed Gigabit Nos. 20 280.00 5600

24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of 24 port Loaded Jack Panel for CAT6A

cable termination at rack end. Data Active

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors for

6 Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250 MHz, Mtr 200 57.00 11400

Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination at

Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply , Installtion , Testing and Comissioning of 24 port Loaded Staggred Jack Panel for

CAT6 cable termination at rack end. Voice Active

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 1 Mtr (3 feet)

9 for information outlet (I/O) to end user device connectivity. (Rack end), High Nos. 10 235.00 2350

Speed Gigabit 26AWG Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet)

10 for information outlet (I/O) to end user device connectivity.High Speed Gigabit Nos. 10 275.00 2750

24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of 2 Port British Style Shuttered Face Plate

white for I/O fixing at user side

Supply , Installtion , Testing and Comissioning of 24 port Loaded Staggred Jack Panel for

CAT6 cable termination at rack end. Riser Active

Supply , Installtion , Testing and Comissioning of 400 pair MDF box complete with Krone

14 Supply , Installtion , Testing and Comissioning of 50 pair riser cable Mtr 15 1,053.00 15795

C Network Rack and Other Accessories

SITC of 14U 600x600 Server Rack with perforation, Glass Door, Cable managemenet,

6/16A power strips- 2 nos, Castors, 4 fan for cooling, Rack should have shelves - 4 nos

Digitally signed by AMIT

S No Description UNIT Qty RATE

16 Supply & Installation Testing & Commissioning of 24PORT managed Network Switch Nos. 1 28,500.00 28500

GST Multiplying factor @ 1.0633 on Electrical DSR 2022 for GST 12% to 18% 27,273.65 126075

Modfied factor of GST on DSR @ 0.973 for considering GST @ 18% instead of 21.27 % - 26,537.26

Digitally signed by AMIT

IP BASED CCTV SYSTEM DSR (INR) NON-DSR (INR)

S No MR Description UNIT Qty RATE TOTAL AMOUNT

S No MR Description UNIT Qty RATE TOTAL AMOUNT

Supply, installation, testing and commissioning of 2MP 2.8mm/3.6mm

wide angle fixed lens IR Dome Camera 1/3" Progressive Scan CMOS;

H.265+/H.265/H.264+/H.264/MJPEG; Colour: 0.01 lux @(F1.2, AGC ON),

1 MR 0 lux with IR; 25fps/30fps (2560×1440, 1920×1080); 3 VCA functions; 3 Nos. 6 4650.00 27,900.00

streams; 3D DNR; ICR; EXIR 2.0, up to 30m; DC12V&PoE

Supply, installation testing and commissioning of Network Video Nos.

recorder Linux based to manage and control all the cameras from

control room. Software shall support maximum 16 channel

2 MR with joystick controller. 256Mbps Bit Rate Input Max(up to 32-ch IP 1 29500.00 29,500.00

video), 2 SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with 2x4TB i.e.

Supply Installation Testing & Commissioning of 32 inch Full HD LED

3 MR monitor including wall mount brackets/ clamps/ desk mounting Nos. 1 24500.00 24,500.00

Supply & Fixing of PCB based Information Outlet (I/O) RJ45, TIA-568C

Category-6, Termination of Catergory-6 UTP Cable, UL listed, Shall

conform to Category-6 as per the EIA/TIA-568C.2, Shall support

network line speeds up to 1 Gbps, Shall have RJ-45 type connector

with bend limiting and strain relief boot for securing IDC contacts

from external forces and for maintaining the bend radius of the

4 MR cable, Shall have minimum durability of 750 mating cycles and Nos. 6 240.00 1,440.00

200 termination cycles. Shall be certified by independent labs

like ETL/GHMT for compliance to EIA/TIA-568C.2. The outlet shall be

fixed in existing box & cover plate in wall/furniture/floor complete as

Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square

plate having spring shuttered front access for preventing ingress

5 MR of dust, dimension as per commercially available modular office Nos. 6 80.00 480.00

Digitally signed by AMIT

Supply & Fixing of UTP Jack Panel UL listed, loaded with 24 no's UTP

ports for PCB based IO Jacks (RJ45, TIA- 568C Category-6), having

integrated bonding bar or other mechanism for grounding,

loaded with individually replaceable 24 nos. Category-6 I/O

Jacks complying with TIA-568.C.2. Shall be 6 port module

6 MR construction for better cable dressing at the rear. The jacks shall Nos 1 9500.00 9,500.00

have RJ-45 type connector with bend limiting and strain relief boot

for securing IDC contacts from external forces and for maintaining

the bend radius of the cable.

Supplying & Fixing of Category 6, UTP patch cords constructed

of 24 AWG unshielded twisted pair stranded copper cable with an

enhanced performance modular plug at each end. Patch cord

cable shall be offered in multiple coloured UTP cable for design

flexibility with a clear strain relief boot on each modular plug. All

patch cords shall be compatible with both T568A and T568B wiring

schemes. UTP Cable, 2 Meter.

Supplying & Fixing of Category 6, UTP patch cords constructed

of 24 AWG unshielded twisted pair stranded copper cable with an

enhanced performance modular plug at each end. Patch cord

cable shall be offered in multiple coloured UTP cable for design

flexibility with a clear strain relief boot on each modular plug. All

patch cords shall be compatible with both T568A and T568B wiring

schemes. UTP Cable, 1 Meter.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO 2025 Description Unit QTY Rate DSR AMOUNT

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120

lm/Watt ) Supplying, installation, Testing & Commissioning of LED

Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type

of following body material with PMMA and prismatic diffuser and

construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal

surge protection of 2.5 KV with Short & Open circuit protection ,THD <

10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free

(flicker should be below 5%), life time (LED,Driver & electrical circuitary),

of minimum 50000 Burning Hours with 70% of initial Lumen maintained till

life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin),

SDCM (Standard Deviation Color Matching) <3, Maximum power

1 1.1 consumption should not more than the specified rating and Fixture shall

be confirming to relevant BIS standards and trade mark certificate (T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing

on housing Complete in all respect i/c connections with 1.5 sq mm FRLS,

PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ≥105

and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape size

and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminum housing such

that LED junction temperature shall not rise above 90°C) Powder coated

die cast /Extruded aluminum Body including trim 1

Digitally signed by AMIT

LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as

per the requirement with Driver efficiency >85%, Operating voltage AC

140- 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver

& electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial

Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11

report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin),

SDCM(Standard Deviation Color Matching) <3, Maximum power

2 1.6 consumption should not more than the specified rating and Fixture shall

be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing

on housing. complete in all respect i/c connections with 1.5 sq mm FRLS,

PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ≥105

<120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape size

and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminum housing such

that LED junction temperature shall not rise above 90°C). Powder coated

die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S TOTAL TOTAL

2022/ DESCRIPTION QTY UNIT RATE

No AMOUNT AMOUNT

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of

1 rating 68 degree centigrade with required accessories :

18.21.1 Pendant type 6 Each 522.00 3132.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless

steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test

18.25 pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head

(Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as

per manufacturer's specifications.

a) MR CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12070.00 12070.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 2 NOS 2740.00 5480.00

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). 2 NOS 4437 8874.00

Rectification & Modification of Existing MS Line Connected to the Branch Pipe as per site

GST Multiplying factor @ 1.0633 on Electrical DSR 2022 for GST 12% to 18% 14504.48 41924.00

Modfied factor of GST on DSR @ 0.973 for considering GST @ 18% instead of 21.27 % 14112.85

Digitally signed by AMIT

S.NO. DESCRIPTION Qty UNIT RATE NDSR Amount DSR AMOUNT

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of

(ii) M.R FIRE PANEL upto 2 zone complete as required. 1.00 No. 14500.00 14500

Supplying, installation, testing & commissioning of smoke

c) 17.1.2 detector with built in LED and Mounting base complete withb 10.00 No. 1153.00 11530.00

all Connections etc. as required.

Supplying, installation, testing & commissioning of manual call

boxes of MS construction in Surface/Recess with Stainless Steel

17.1.3 chain & hammer Assembly complete with glass and push 2.00 No. 474.00 948.00

button etc. as Required.

Supplying, installation, testing & commissioning of response

indicator on surface/recessed MS Box having two LED, metallic

cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm

Sounder with Facility to make annoucement, mountedc in M.S

e) 17.1.6 Box (16 SWG) with Hinged cover plate & Suitable for operation 2.00 No. 557.00 1114.00

with Amplifier i/c line matching transformer etc complete as

CABLING & WIRING

Supplying & laying of 2x1.5 sqmm fire survival alarm armoured

cable, 600/1000V rated with annealed copper conductor

a) 17.5.2 having XLPE insulation, steel wire armouring & ERLS outer sheath 200.00 Metre 173.00 34600.00

complete as required.

GST Multiplying factor @ 1.0633 on Electrical DSR 2022 for GST 12% to

Modfied factor of GST on DSR @ 0.973 for considering GST @ 18%

instead of 21.27 %

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 36mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall

be provisioned with back unit of overall size: 1900mm(L) x 450mm(D) x 750mm(H) . Side

storage having a provision for three equal drawer unit and two openable shutter & one

open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre

laminated particle board and rest all storage to be made out of 18mm thick pre laminated

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire

passing or as per site requirement. Main Table Dimension (L)1900mm X (D) 900mm X

(H)750mm overall Side Runer Dimension (L)1000mm X (D) 400mm X (H) 675mm with back

Storage (L)1600mm X (D) 400mm X (H) 675mm

Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size

:-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and

AGM High back) upholstered with leatheritte and cut foam. The chrome plated loop armrest with

Back Chair padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with

nylon castors . Chair seat has foam of density 30- 35 (+/ 2kg /m3) Dimensions The backrest

has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X

(D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X

3 (D)505mm X (H)990mm, Back Type:Cantilever, Base: Cantilever Frame, Base Type:Cantilever, Nos. 3.00 12,500 37500

Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed

plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35

kg/m3. The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class

to the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour

& Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam

4 3 seater sofa beech solid wood have used for framing construction of sofa .The seat cushion is made of Nos. 2.00 39,500 79000

multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of

elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1800mm X (D)750mm X (H)710mm

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class

to the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour

& Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam

5 2 seater sofa beech solid wood have used for framing construction of sofa .The seat cushion is made of Nos. 1.00 29,500 29500

multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of

elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The

backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 36mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall

6 be provisioned with Side unit of overall size: 1000mm(L) x 450mm(D) x 675mm(H) . Side Nos. 2.00 36,500 73000

storage having a provision for three equal drawer unit and two openable shutter & one

open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre

laminated particle board and rest all storage to be made out of 18mm thick pre laminated

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire

passing or as per site requirement. Main Table Dimension (L)1450mm X (D) 700mm X

(H)750mm overall Side Runer Dimension (L)1000mm X (D) 450mm X (H) 675mm

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L)

x 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR

plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The

Manager chair shall be provided with self tension single locking mechanism and pneumatic height

High Chair adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height

adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze

chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be

ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS

8 Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chair shall be Nos. 14.00 12,500 175000

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five

star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg /m3) The

backrest has a foam of 28kg/m3.

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With

Side Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm

Partition Ht. 1200mm, Double Raceway systems Skirting label and below the table top . lower

tile both side laminated and upper tile inside side fabric, White Board and white Tinted Glass

9 . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end 18mm thick MDF board., Nos. 4.00 26,500 106000

and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H made in 18mm

thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For drawer Facia-

Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating- Munshel Gray. and White Tinted

Supply and Placing of Reception Table, made from pre-laminated particle board with

Reception laminate finish. Includes drawers, keyboard tray, modesty panel, and cable management.

Table All hardware fittings (handles, channels, locks) included. Finish and design as approved by

Engineer-in-Charge. Complete in all respects as per approved design.

Pantry Lunch Providing & Installation of Pantry table of size 1.5m x 0.75m x 1.05m (ht) made out of 19mm

Table thk. Commercial Board finished in Laminte.

13 Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC Nos. 2.00 2,450 4,900.00

14 TABLE CENTRE TABLE WITH GLASS TOP Nos. 1.00 10,500.00 10,500.00

15 SIDE Table Side Table Nos. 2.00 8,000.00 16,000.00

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Meeting Table for 7 Persons, comprising:

– Table Top: Made of 25mm thick prelaminated particle board of approved shade,

Meating conforming to E1 norms. All edges to have machine-pressed 2mm thick imported PVC

Table lipping fixed with hotmelt EVA glue, free from VOC.

– Gable End and Modesty Panel: Made of 18mm thick prelaminated particle board of

matching approved shade, with similar 2mm PVC edge banding.

Pantry Under Counter Storage, made with HDHMR board finished with laminate on all

exposed surfaces. Unit depth: 600mm. All edges shall be finished with matching edge

banding. Includes shutters, shelves, hardware (hinges, handles), and necessary fittings

complete in all respects.

Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade

conforming to E1 norms, with unit depth of 450mm. All exposed edges finished with 2mm

PVC edge banding using hotmelt EVA glue. Includes shutters, shelves, and necessary

hardware and fittings, complete in all respects.

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back

Openable panel is made of 09mm thick MDF of approved shade. All the edges of storage surface shall

20 Shutter be provided with machine pressed imported PVC lipping glued with hot melt EVA glue free

storage from any VOC with free groove handle and suitable lock. All exposed area PVC edge

Total Amount 851900

Total Amount 851900

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: SIGNAGE

S No Description Unit Qty Unit price DSR Non-DSR

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern with Mat

MR /Gloss Finish Brass Letters with Mettalic/ Acrylic Base, complete as required at site with sq inch 4900 18 88200

the direction of the Enginner In Charge

Digitally signed by AMIT