Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹307.7 CrAccepted-Finance | ₹307.7 Cr | L1 | Accepted-Finance Lowest rate found. |
| 2 | L2₹332.2 CrAccepted-Finance 401 THE GRAND MALL OPP STATE BANK ZONAL OFFICE S M ROAD AMBAWADI AHMEDABAD 380015 | AHMADABAD | GUJARAT | 380015 | ₹332.2 Cr | L2 | Accepted-Finance High rate found. |
| 3 | Rejected-Technical 203 204 27 2ND FLOOR BENTINCK STREET KOLKATA WEST BENGAL 700001 | KOLKATA | WEST BENGAL | 700001 | - | - | Rejected-Technical The document not submitted as per tender terms and condition, i.e Initial criteria for eligibility. III Similar completion Project or work in any category. |
| 4 | Rejected-Technical | - | - | Rejected-Technical The document not submitted as per tender terms and condition, i.e Initial criteria for eligibility. III Not fulfill the criteria of completion works in any category. |
| Sl No | Description | Qty | Unit | Dineshchandra R Agrawal Infracon Pvt. Ltd. | M/s. ASHOKA BUILDCON LIMITED |
|---|---|---|---|---|---|
| 1.00Civil works | |||||
| 1.01 | Detailed designing, Engineering,
Procurement & Construction of Vehicular bridge with all required survey and soil investigation, Clearing and grubbing site/road/land, dismantling required surfaces, Earthen coffer bund, Pile foundation in M50 grade concrete, pile test, Substructure likes pier, abutment, Stem, Retaining wall in M50 grade concrete etc., aluminium formwork, RCC Super Structure, all types of steel girders including Supplying fabrication assembling and erection , Expansion joints, load test on deck, Transparent Noise barrier, Cylindrical" type rubber fenders, Railing, Rigid pavement on Approaches including road crust and earthwork, Emergency Vehicular bridge Access Control System etc. as per scope, drawings, design & Specifications, Codes and Practices contained in tender document. The design of facilities shall confirm to standard specified by PWD, MORTH, IRC, IS etc. including:
(a) And all other works covered under Scope of work and meeting all relevant statutory requirements complete as required. | 1 | Job. | 1,87,15,00,000 ₹187.2 Cr | 1,79,50,00,000 ₹179.5 Cr |
| 1.02 | Detailed designing, Engineering,
Procurement & Construction of Pedestrian bridge with all required survey and soil investigation, Earthen coffer bund, Pile foundation in M50 grade concrete, pile test, Substructure in M50 grade concrete, aluminium formwork, RCC Super Structure, all types of steel girders including Supplying fabrication assembling and erection , Expansion joints, load test on deck, Railing, Crash barrier and kerbing, Transparent Noise barrier, Cylindrical" type rubber fenders, Emergency Pedestrian Bridge Access Control System etc. as per scope, drawings, design & Specifications, Codes and Practices contained in tender document. The design of facilities shall confirm to standard specified by PWD, MORTH, IRC, IS etc. including:
(a) And all other works covered under Scope of work and meeting all relevant statutory requirements complete as required. | 1 | Job. | 81,27,00,000 ₹81.3 Cr | 78,75,62,307 ₹78.8 Cr |
| 1.03 | Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in
(A) Foundations, footings, Base or columns and Mass concrete | 540 | Cum | 24,04,620 ₹24.0 L | 39,30,120 ₹39.3 L |
| 1.04 | Providing and laying damp proof course 25mm thick cement concrete 1:2:4 (1-Cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size) and curing complete | 5,330 | Sqm | 18,86,820 ₹18.9 L | 8,79,450 ₹8.8 L |
| 1.05 | Providing and laying controlled cement concrete M.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in
(B) Walls, from top of foundation level upto floor two level | 240 | Cum | 12,21,360 ₹12.2 L | 18,56,160 ₹18.6 L |
| 1.06 | Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse sand : 4- graded stone aggregates 20 mm nominal size) exposed work with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for R.C.C work in
(ii) Slabs having more than 8 cm and upto 10 cm.thickness | 70 | Cum | 6,64,160 ₹6.6 L | 5,09,460 ₹5.1 L |
| 1.07 | Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level | 1,59,702.6 | Kg | 1,45,32,936.6 ₹1.5 Cr | 1,21,37,397.6 ₹1.2 Cr |
| 1.08 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,
(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | 580.08 | Kg | 5,66,738.16 ₹5.7 L | 1,23,557.04 ₹1.2 L |
| 1.09 | Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials
(A) By manual means in area of light jungle | 0.73 | Hectare | 41,555.25 ₹41,555.25 | 26,849.4 ₹26,849.40 |
Updated dates
Tender Value
₹270.5 Cr
EMD Value
₹2.8 Cr
Closing Date
10 Dec 2025, 2:00 pmClosed
The Exe., Engg., PWD, WD-I, Daman.
The Multi Office Complex, PWD, 2nd Floor, Near Moti Daman Market, Moti Daman.
CONSTRUCTION OF PROPOSED SIGNATURE BRIDGE CONNECTING JAMPORE SEA FRONT ROAD NEAR LIGHT HOUSE TO DEVKA SEA FRONT ROAD AT PARKOTA SHERI AT DAMAN.(3rd call)
2025_DAMAN_4502_1
Tender Notice No.104/Signature Bridge/2025-26
Open Tender
Civil Works
1095 days
Daman District.
Please refer Tender documents.
2 documents required · 2 mandatory
₹10,000
The Exe., Engg., PWD, WD-I, Daman.
₹2.8 Cr
The Exe., Engg., PWD, WD-I, Daman.
2 Jan 2026
6 Oct 2025
10 Dec 2025
6 Oct 2025
10 Dec 2025
6 Oct 2025
16 Oct 2025
Civil works
Detailed designing, Engineering, Procurement & Construction of Vehicular bridge with all required survey and soil investigation, Clearing and grubbing site/road/land, dismantling required surfaces, Earthen coffer bund, Pile foundation in M50 grade concrete, pile test, Substructure likes pier, abutment, Stem, Retaining wall in M50 grade concrete etc., aluminium formwork, RCC Super Structure, all types of steel girders including Supplying fabrication assembling and erection , Expansion joints, load test on deck, Transparent Noise barrier, Cylindrical" type rubber fenders, Railing, Rigid pavement on Approaches including road crust and earthwork, Emergency Vehicular bridge Access Control System etc. as per scope, drawings, design & Specifications, Codes and Practices contained in tender document. The design of facilities shall confirm to standard specified by PWD, MORTH, IRC, IS etc. including: (a) And all other works covered under Scope of work and meeting all relevant statutory requirements complete as required.
Detailed designing, Engineering, Procurement & Construction of Pedestrian bridge with all required survey and soil investigation, Earthen coffer bund, Pile foundation in M50 grade concrete, pile test, Substructure in M50 grade concrete, aluminium formwork, RCC Super Structure, all types of steel girders including Supplying fabrication assembling and erection , Expansion joints, load test on deck, Railing, Crash barrier and kerbing, Transparent Noise barrier, Cylindrical" type rubber fenders, Emergency Pedestrian Bridge Access Control System etc. as per scope, drawings, design & Specifications, Codes and Practices contained in tender document. The design of facilities shall confirm to standard specified by PWD, MORTH, IRC, IS etc. including: (a) And all other works covered under Scope of work and meeting all relevant statutory requirements complete as required.
Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base or columns and Mass concrete
Providing and laying damp proof course 25mm thick cement concrete 1:2:4 (1-Cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size) and curing complete
Providing and laying controlled cement concrete M.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level
Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse sand : 4- graded stone aggregates 20 mm nominal size) exposed work with curing etc. complete including the cost of formwork but excluding the cost of reinforsement for R.C.C work in (ii) Slabs having more than 8 cm and upto 10 cm.thickness
Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials (A) By manual means in area of light jungle
Engraving letters in hard stone
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : - Steel Grey Granite (40 mm thk)
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : - Kashmir Gold Granite (40 mm thk)
80 mm thk Granite for Signage
Supply and application of Pebblewash with average 15mm thickness Item : FREEFORM PEBBLEWASH GREY MINI PIGEONEGG including application of Aggr. Gr 3 S
Supply and application of Pebblewash with average 15mm thickness Item : FREEFORM PEBBLEWASH RED MINI SCARLET
Supply and application of MIcroCement Floor Fine Top Coat with average 3mm thickness Item : FREEFORM MICROCEMENT FLOOR FINE TOP COAT ROSEWOOD (L)
SAE 316L Brush Finish "L" Section for Stonecrete Flooring
SAE 316L Brush Finish Studs for Tactile Flooring
Providing and applying Grey Stonecrete (10mm thickness) Plaster as per drawings including all labour, material, etc as directed by EIC
Providing and applying Brown Mini Mahi Stonecrete Plaster (10mm thickness) as per drawings including all labour, material, etc as directed by EIC
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Seat up to 1.80 (L) x 0.60 (W) x 0.45 (H) x 0.03(Thickness)
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Planter Box 01 up to 2.10 (Dia) x 1.50 (H) x 0.03(Thickness)
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Planter Box up 02 to 2.10 (L) x 0.90 (W) x 0.90 (H) x 0.03(Thickness)
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Planter Pot up to 1.5 (Dia) x 1.2 (H) x 0.03(Thickness)
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc For Approximate size of Pergola - ??
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Bollard up to 0.45 (L) 0.45 (WD) x 0.90 (H) x 0.03(Thickness)
Providing & laying exposed Precast Glass fiber reinforcement concrete with 6MPa Tensile Strength, 30 mm Thk (Reccommended for Furniture in Public Use) Planter and lifting to all heights & erecting and placing in its final position complete in all respect as per the approved drawings and as directed by engineer in charge. The rates includes the cost of admixtures & necessary equipment's for precasting of panel, curing tanks/curing of precast panel by means of water sprinklers/steam curing etc., cost of providing and maintaining living tools, tackles and necessary cranes/hoists etc. For Approximate size of Dustbin up to 0.45 (Dia) x 0.90 (H) x 0.03(Thickness)
40 mm thick flooring - Kota stone - shot blasted finish Providing and laying textured finish (shot-blasted finish or similar) Lime stone flooring in required design and patterns, in linear as well as curvilinear portions etc all complete as per the architectural drawings with 40mm thick Kota stone over 40 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and cleaning etc. all complete as specified and as directed by the Engineer-in-Charge. If required, exposed edge of stone shall be finished and corner treated. Sample shall be approved by Architect.
Granite cobble Providing and fixing Granite cobble stones of 40mm thick of any shade any size as per drawing and as approved by Architect, in approved pattern, laid on 40mm thick Cement mortar bed of proportion 1:4 and 5-8mm groove filling the joints with approved pigmented cement mortar in proportion 1:4, including grouting the joints in 1:2 proportion to match with the shade of stone, curing, cleaning, etc. complete as approved and as directed by EIC. Sample and mock-up shall be approved by Architect.
Precast Concrete kerb Providing and fixing M25 grade concrete factory-made precast exposed/fair/ textured finish kerb stones of an approved make and as per the approved sample, in any size or shape. The kerbs shall have chamfered or pencil corner edges. They shall be fixed on a base of plain cement concrete (PCC) with a cement mortar of 1:2, including flush pointing in cement mortar (1:2) for all joints, curing, etc., complete. The rate shall also include the erection and fixing of all varieties and shapes of kerbs (such as radius kerbs, corner kerbs, quadrant kerbs, drain-out kerbs, flat kerbs, parking edge kerbs, ramp kerbs, etc.) as per the drawing. Samples and mock-ups shall be approved by the Architect and as directed by the Engineer-in-Charge. The actual laid volume shall be measured for payment of rectangle shape volume.
HORTICULTURE Supplying and stacking of good earth at site (earth measured in stacks will be reduced by 20% for payment). Good earth shall consist of a free draining organic soil from horizons less that 300mm from the original surface, of a workable crumbly and lump free loamy character and shall contain no grass or weed growth of any kind or other foreign material or stones exceeding 25mm in diameter. Total stone content shall be no greater than 5% by volume. A 1 litre sample with back up soil test data is required before supply, to be approved by EIC. Soil should conform to the following parameters: pH 5.5 - 7.8, Electrical conductivity 1:2.5 (w/v), Soil-water extract not exceeding 1500 micromho/cm, Soil texture Sand (0.05 - 2.00mm) Max. 75% Min. 20%, Silt (0.002 - 0.05mm) Max. 60% Min. 5%, Clay (less than 0.002mm) Max. 30% Min. 5%. Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required for supply and stacking of good earth.
Supplying and stacking of well decayed cow dung manure (cattle manure measured in stacks will be reduced by 8% for Payment). Manure shall be well composted, dried, well screened good quality in powdered form. Manure, shall be free from soil clods, fresh mung grass, and dry. Sample will be approved by EIC. Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required for supply and stacking of good earth.
Supplying and stacking of well decompose vermicompost (vermicompost measured in stacks will reduced by 8% for Payment). Manure shall be well composted, dried, well screened good quality in powdered form. Vermicompost, shall be free from soil clods, grass seed and dry. Sample will be approved by EIC. Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required for supply and stacking of good earth.
Supply & stacking of cocopeat. Good cocopeat shall free from other foreign material, with pH 5.2 to 6.8, uniform texture, 1 to 2 CU testing without mixture of any fertilizer. Moisture: 10%-15% Fibre Content: <2% EC :1 to 1.5 w/v Sand: 2%
Supplying and stacking of perlite. Good perlite aggregate should not contain any added chemicals, dyes, or impurities. It should be clean and free of contaminants. The ideal size of perlite is a 1-5mm diameter grains. Good perlite’s Ph should be 7 to 7.5.
Supply, Staking & Laying of Aggregate 6mm size including loading, unloading, carriage and all taxes paid etc. and as per direction of Engineer in charge.
Supply & stacking of charcoal. Good charcoal shall free from other foreign material, natural hardwood charcoal or biochar with pH 5.2 to 6.8, uniform texture. Moisture: below 5-10% EC :0.1 to 400 S/cm.
Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in- charge in filling in Planter bed
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water) Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required as directed by EIC - Shrubs
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water) Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required as directed by EIC - Trees & Palms
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water) Item includes all royalty, equipment, labour, loading, unloading, and carriage upto any lead & lift required as directed by EIC- Ground Cover
Supply of Shrubs - well developed, well branched - 3-4 branches each having 4-5 leaves, preferably in bloom, in polybag of 30x20cm size, disease free and development (height 0.75-0.9m) Shrubs are woody perennials of generally multi stemmed and bushy habit ranging from 3 - 4.5m down to 500mm height. Shrubs shall have no less than three main stems and shall be well balanced and bushy, with strongly developed fibrous root systems, and shall be pruned in advance as required to achieve the specified height tolerances. Branches shall break from the base of the plant just above the root collar, and shall be well furnished with leaves right down to ground level. Supply shall include labour & equipment cost of loading, unloading, transport to site, storage & stacking within site in area protected from dust using temporary agronet, watering & maintenance at stacking area until planted as directed by EIC SHRUBS Bougainvillea spectabilis (Paper Flower) [Sh/Bosp] {14"}
Calliandra haematocephala (Red Powder Puff) [Sh/Caha] {9"}
Hibiscus tiliaceus (Sea hibiscus) [Sh/Hiti] {9"}
Hibiscus tiliaceus dwarf (Sea hibiscus-Dwarf) [Sh/Hiti-D] {14"}
Lantana sellowiana (weeping lantana) [Sh/Lase] {9"}
Leucophyllum frutescens (Texas sage) [Sh/Lefr] {12"}
Nerium oleander (Karen) [Sh/Neol] {12"}
Nerium oleander Dwarf white (Dwarf White Karen) [Sh/Neol-w] {12"}
Nerium oleander light pink (Light pink Karen) [Sh/Neo-li-p] {12"}
Nerium oleander Pink (Pink Karen) [Sh/Neol-p] {12"}
Nerium oleander Red (Red Karen) [Sh/Neol-r] {12"}
Nerium oleander white (White Karen) [Sh/Neol-w] {12"}
Nerium oleander yellow (yellow Karen) [Sh/Neol-y] {12"}
Scaevola taccada (Beach cabbage) [Sh/Scta] {14"}
Thevetia peruviana-Pink (Pink oleander) [Sh/Thpe-P] {8"}
Thevetia peruviana-White (White oleander) [Sh/Thpe-W] {8"}
Thevetia peruviana-Yellow (Yellow oleander) [Sh/Thpe-Y] {8"}
Clusia rosea (Balsam Apple) [Sh/Clro] {10"}
Ophiopogon japonicus (Monkey Grass) [Gr/Opja] {8"}
Supply of Trees - well developed, well branched crown - 4-6 branches each having 4-5 leaves, well developed (Poly bag size - 18"x 18", min. stem diameter 50mm and height as specified) Trees shall be large size nursery grown trees pruned during growth to produce a tight well rounded head and a straight stem clear of leaves or twigs. Trees shall be at least two years old, as certified by the nursery. Trees shall be 70-100 mm circumference stem when measured 1.0m from ground level and shall have a clear straight stem of minimum 1.2m. The head shall be well balanced and rounded and contain at least four main branches with a well-developed secondary branch system and a defined central leader that has not been pruned, giving a minimum overall height of 1.5m at the time of planting. Rootball dimensions : diameter 400mm x 400mm deep minimum. Branching/leaf spread 1.5 - 1.8m diameter. Pruning at the time of removal from the nursery will not be permitted. In dry weather conditions, trees are to be sprayed with approved Anti-transpirant. Trees shall have a strong fibrous root system. Supply shall include labour & equipment cost of loading, unloading, transport to site, storage & stacking within site in area protected from dust using temporary agronet, watering & maintenance at stacking area until planted as directed by EIC TREES Barringtonia acutangula (Freshwater Mangrove) [T/Baac] {21"}
Barringtonia asiatica (Sea Poison Tree) [T/Baas] {21"}
Barringtonia racemosa (Powderpuff Mangrove) [T/Bara] {21"}
Calophyllum inophyllum (Indian Laurel) [T/Cain] {30"}
Thespesia populnea (Indian Tulip Tree) [T/Thpo] {25"}
Supply of Palms - well developed, well developed, disease free (Poly bag size - 18"x 18") Palms shall have heights as either 1.2m-1.5m. For single stemmed palms, the clear trunk height shall be atleast 80% of specified height, and stem girth shall be of dimension normally found for palms for the stem height and species specified. Acceptable tolerances to variations in stem height shall be +200mm or - 200mm from the height specified in the Bills of Quantities. The heads of palms shall be well balanced with at least 7 leaves and a healthy growing apical shoot all free from pest and disease. Rootball dimensions shall be 450mm diameter x 450mm depth. Supply shall include labour & equipment cost of loading, unloading, transport to site, storage & stacking within site in area protected from dust using temporary agronet, watering & maintenance at stacking area until planted as directed by EIC PALMS Phoenix dactylifera (Date Palm) [P/Phda] {Loos bag}
Supply of Ground covers / creepers - well developed, min. 0.15m high, in polybag of 5"x7" size, disease free. All groundcover species shall be evenly balanced to allow equal growth in all directions. Plants shall have fully developed roots and leaves. Rooted cuttings will not be accepted. All plants to be container grown. Supply shall include labour & equipment cost of loading, unloading, transport to site, storage & stacking within site in area protected from dust using temporary agronet, watering & maintenance at stacking area until planted as directed by EIC. GROUND COVERS Wedelia trilobata (Singapore Daisy) [Gc/Wetr] {8"}
Vernonia Elaegnifolia (Curtain Creeper) [C/Veel] {8"}
DRAIN CELL Providing and fixing 20mm Drain Cell of approved make and as per manufacturer's recommendation below landscaping area and as directed by Engineer in chrage.
Supply and installation of filter Geotextile membrane, 250 gsm non woven, 100% polypropylene of thickness 2 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation including all labour, material and equipment and supply upto any lead and lift as directed by Engineer-In-Charge
Staking of trees, palms and large shrubs using quadrapod staking made of 4 nos Bamboo 25 mm dia 2.5 metre long, fixed 0.3m in the soil and joined at 2/3 height of plant stem using jute rope, fixed to plant using rubber sheath; plant stem to be covered with gunny / jute cloth at fixing point to prevent damage, complete including supply of all material, labour and equipment, upto any lead and lift as directed by EIC
Complete maintenance of the plantation area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by EIC (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide, will be provided by the Institution & other T & P material/articles shall be provided by the contractor, as per yard stick 1Mali per acre (5 years)
Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.
Lining Planterss with 200 micron woven multi-layer cross laminated, UV Stabilized HDPE lining as per IS 15351:2008, with joints welded using fusion welding machine or heat based plastic welding machine, and all joints checked for leakage using air pressure testing, and anchoring of lining at all ends by laying in anchor trench, including supply of all material, labour and equipment up to any lead and lift; as directed by Engineer-in-Charge.
Design, Fabricate, and erect the structural steel of 2602 grade,support for the facade elements at various locations. All mild steel should be hot dip galvanised with an average coating thickness of 130 Micron. The coating shall be further shot blasted upto average 7 micron to improve the bonding withthe paint. Scope to include all lead and lift to any position on elevation of the bridge using manual or mechanical methods as required, placing, drilling, bolting, streightening, grinding, welding, removing flaux, scaling, dirt etc. Preparing zigs, Farma,Moulds, Gauges, dies, etc for fabricating, cutting bending, shaping the members using mechanical methods. Cutting using hack saw, grinders, shapers, trimmers,using oxyacetelene gas or lazer guided CNC machines .All welding must be done using Advani, Orlikon, Esab welding electrodes of diameter as required. Finishing the edge/corners/faces etc, profile shall be done using rotary or linear profile grinders. cutting holes using gas shall not be allowed.The rate to include all consumables required such as oxyacetelene gas, welding rods, HT nut- bolt assembly, SS 304 chemical anchors, for permanent as well as for temporary works. All needful tools tackles rigs, temporary platforms etc .Once the HDGI coating is done welding will not be allowed at site. All connections shall be designed as bolted connections. Bridge HDGI Fabricated 200x125x 6mm thick including cast-in-channels, HDGI Bracket with Anchor minimum M12-110 mm long, 12 mm thick HDGI U Barcket for curved Vertical HDGI Tube as per structural calculation. Includes preheating for uniform welding.
Bridge HDGI Fabricated 250x125x10 mm thick including cast-in-channels, HDGI Bracket with Anchor minimum M12-110 mm long, 12 mm thick HDGI U Barcket for curved Vertical HDGI Tube as per structural calculation. Includes preheating for uniform welding.
Scope: Designing the structural railing on the bridge deck floor. The railing shall be made out of SS 316 of the thickness as per the structural design. All the base plates and chemical anchors shall be concealed using Matching colour SS cover caps as per architectural approval. All the welding shall be grind polished and shaped to look elegant. Only bolted connections are allowed at site. Rate to include the mock up of 3 meter long railing for architectural approval. The railing shall be structurally designed to carry wind load 500kg/smt plus live load of 225kg/rmt or 300 kg/Sq mt (infill panel load) whichever is stringent/greater. Note: Only the visible length of hand rail be measured for the payment irrespective of the height and concealed portions if any. I.DESIGN: Design: Design engineer and install pre-assembled SS 316 members to withstand a minimum design wind load 500kg/smt and live load of 225 Kg/Rmt . The railing shall be tasted by applying pull of 225 kg at site using load cell and hydraulic pulling machines after installation. The railing must pass the pull load and shot bag test. The railing of item no 2.1a shall comprise of the followings in SS 316 grade, satin finished RHS members as per str design SS Chemical anchor fasteners of M12 x 250 mm of Hilti or equivalent make Base plate of 450x450x20 mm thick A couple of balustrades of 65x25x6 mm thick @ 1500 mm c/c Horizontal intermediate rails of 65x25x6 mm thick. Vertical pipes of 20 mm dia 1.6 mm thick at 100 mm C/C 65 mm dia 3 mm thick hand rail with concealed end connections with 3 mm groove between vertical end balustrades and the horizontal hand rail. Railing in SS 316 for a height of 1200 mm as per drawing- 19mm2layer + SGP 3.04 -1 layer
Railing in HDGI epoxy painted for a height of 2200 mm as per drawing - 19mm4layer + SGP 3.04 - 3 layer
Scope: Designing the structural glass flooring on the bridge deck floor. The flooring shall be made out of SGP laminated glass and HDGI RHS of size and thickness as per the approved structural design. All base plates and bolt assemblies / chemical anchors shall be fully concealed using matching colour SS cover caps, subject to architectural approval. All welding shall be grind-polished and shaped for an elegant finish. Only bolted connections are permitted at site. The rate shall include a mock-up of a 2 grid x2 grid for architectural and engineering approval. The flooring shall be structurally designed to carry dead load + live load of 7.5 kN/sq.m (exceeding standard code requirements; vendors to quote as per this load) + wind load of 300 kg/sq.m. The flooring system shall be laboratory tested for all loading combinations at 1.5 times the design load. The top and bottom layer shall be of 6 mm additional sacrificial glass with top glass having antiskid raised bubbles and both with coating of hydrophobic sealer of Wacker/dow/clearshield make. Even if 12 mm glass and 1.52 mm SGP passes the design vendor shall provide 19 mm thick glasses and 3.04 SGP only to reduce the risk of fatigue. The topmost glass shall have inbuilt anti-skid dots. The scope shall include all decorative elements such as brackets from the main steel beams to the mullions and transoms of the glass flooring, designer connectors, CNC works, bending to radius, complete including glass, SGP, and wastage. Glass flooring shall comprise a minimum of four layers of 19 mm extra clear glass, with the top layer incorporating raised round dots of 20 mm diameter, raised by 1.5 mm, placed at a 50 mm c/c pitch or an optimized combination to achieve superior anti-skid performance.Three layers of 3.04 mm SentryGlas® Plus (SGP) lamination shall be used between the glass layers.All glass shall be extra clear and heat-strengthened. All joints shall be sealed using extra clear silicone sealant. Glass edges shall come factory-protected to prevent any corrosion of the lamination layers. The glass supplier must provide a 20-year lamination warranty....
Supply, Installation, Testing and Commissioning (With 5 year O&M) of IP65 Outdoor light column maximum total 250-270W, 1) with fixed 180 degree/ asymmetrical distribution including the LED downlight modules; 2700K 2)10-30 degree distribution (±10% allowed) 4@25-45W LED adjustable GOBO projector to be integrated within the pole cylinder and custom glass GOBO Lens, CCT: 6300-6700K 3) Asymmetric forward throw totally 15-20W LED walkway light module; 2700K 4) Outdoor IP rated Speaker, all components to be housed within the cylindrical form of the pole.(For asymmetric module) Load type 220-240V AC, Minimum delivered luminous flux 1800lm*, Minimum Efficacy 35lm/W*, Lamp life ≥50,000 hrs L80 B10, SDCM ≤3, CRI ≥ 80, THD < 10%, Power factor 0.9 or above. Minimum IK08 certified, Class II safety protection, Integral DALI-2 Dimmable Driver(For GOBO projector @ 1 nos.) Load type 220-240V AC, Minimum delivered luminous flux 2000lm*, Minimum Efficacy 55lm/W*, Lamp life ≥50,000 hrs L80/B10, SDCM ≤3, CRI ≥ 80, THD < 10%, Power factor 0.9 or above. Minimum IK08 certified., Class I safety protection, Integral DALI-2/DMX Dimmable Driver(For asymmetric forward throw walkway light) Load type 220-240V AC, Minimum delivered luminous flux 900lm, Minimum Efficacy 45lm/W*, Lamp life ≥50,000 hrs L70 B10, SDCM ≤3, CRI ≥ 80, THD < 10%, Power factor 0.9 or above. Minimum IK08 certified, Class II safety protection, Integral DALI-2 Dimmable DriverLuminaire with extruded aluminium corrosion resistant housing, high efficiency, durable, extremely reliable components. The luminaire body shall be treated with marine treatment. Marine-grade coating , extruded aluminium alloy pole of minimum 6mm wall thickness with class I safety protection. Excellent light distribution, curved Borosilicate glass should be precisely fixed on a Lense carrier. Minimum 3 preset spacers to be able to correct the keystone effect, making an exchange of seasonal masks easily achieved at any time without readjustment. masks should be maintenance-free. The power supply unit should be external, in either an extra housing or integrated into the pole. Conventionally replaceable source LED module. Installations shall include technical planning, illuminance, photo-finish for orientation, setup of device, optical parts and pre-focus. The Luminaire and mounting accessories shall be treated with Anti-saline treatment. Controller is equipped with Ambient light sensor. Enables remote management and control of Luminaire offers Adaptive, autonomous, Astro clock and calendar-based dimming. Pole shall be equipped with speakers. All equipment's shall be housed in the cylindrical form of the Luminaire and be accessible by vandal proof inspection hatch. Pole shall be made of extruded aluminium with marine finish and covered with injection moulded...
Supply, Installation, Testing and Commissioning (With 5 year O&M) of IP65 Outdoor Surface Ground 115 degree distribution total of 55W RGBW LED = 0.6W RGBW LED per media pixel (300mm pitch) with clear cover mounted in 3 SS316/ Anodized Aluminium rings of Dia ranging from 1m, 1.5m, 2.5m in two-way direction: aiming up and aiming down, rings are mounted on 3 curved SS316/ Marine grade C5-m Finish GI 75mm Dia pole of height 3m, RGBW Luminaire to have 220-240V AC supply with appropriate low voltage (24V DC/ 12V DC) transformer, per chain light node/ module : Minimum Delivered luminous flux is 17lm , Minimum Luminaire efficacy 28lm/W, 1L.5ammp life ≥50,030.00mhrs L70 B10,4T5HmD < 10%, Pmower factor 0.9 or above. Minimum IK07 P1r8o6teclxtion, Remo1t5e DlxMX Dimma8b0le xDriverAn o2u9tdlxoor rated media pixel Harsh Environment strands are fully sealed with UV resistant thermoplastic overmold, IP66-rated for harsh outdoor applications, especially in coastal environments. All flex nodes are with a thermoplastic overmold flex Luminaires can handle a wide range of extreme conditions, such as dust, humidity, corrosion, and temperature shifts found in coastal locations. Each strands consist of 50 large, individually controllable, high-intensity LED nodes. Each node produces full-colour light output of up 25 candela. The strands with spacers ensures consistent alignment and spacing. Detachable leader cables in multiple lengths allow you to install strands at the appropriate distance from power/data supplies. Protected against electrostatic discharge + 2,000V and C44polarity miss wiring. The 3 rings are made with SS 316 having a H-channel and perforated cover on top and bottom, aligned to the chain light modules mounted inside it. The rings are of different dias ranging from 1m, 2m and 3m supported on 3 curved SS316/ marine grade GI 75mm Dia poles- (with SS316 or GI with Marine grade finish) of 3m height. The rings are bolted/welded with the poles with marine grade fasteners. The mounting arrangement of rings and pole to be referred from a separate drawing. 1m Dia ring consist of total 20 nos. chain light nodes/ modules (10 nos. chain light nodes/ modules aiming up + 10 nos. chain light nodes/ modules aiming down) ,1.5m Dia ring consist of total 30 nos. chain light nodes/ modules (15 nos. chain light nodes/ modules aiming up + 15 nos. chain light nodes/ modules aiming down), 2m Dia ring consist of total 40 nos. chain light nodes/ modules (20 nos. chain light nodes/ modules aiming up + 20 nos. chain light nodes/ modules aiming down). Detachable leader cables in multiple lengths allow you to install strands at the appropriate distance from power/data supplies. Protected against electrostatic discharge + 2,000V and polarity miss....
SITC of Centralised LMS/LCS system must be implemented for all OUTDOOR Lighting using Wired/Ethernet protocolsAll Dimming shall be DALI2 or DMX512 or DMX/RDM compatible Any Switching required in any area shall be switching through the LMS/LCS relays using networked sensors or relays only. Item Rate must include all PSU, Repeaters, Controllers, Keypads, Ethernet Switches/Ports and Accessories to make the system fully functionable. LMS/LCS façade & event thematic lighting Control System required for Weekday, weekend and festival : Based on the detailed written specific LIGHTING Programming Brief for Weekday, weekend and festival given by the PPC/Main Architect/PPC Lighting Consultant, the Visualisation of Effects of the RGB/RGBW/RGBA Lighting Control system must be imagined/visualized and depicted by the Lighting Contractor in the form of two to three basic animated moving image file to communicate the Creative Intent to satisfy the given brief. a. For Weekend & Festivals days : The Number of required pre-programmed SCENES to be provided by the Lighting Contractor must NOT BE LESS Than 3 individual scenes and NOT MORE THAN 6 (six) preprogrammed scenes. Each scene / low resolution moving light moving image low resolution video content shall be of minimum 5min each. Minimum 3 scenes/ low resolution moving light moving image low resolution videosb. For Weekdays & regular days : The Number of required pre- programmed SCENES to be provided by the Lighting Contractor must NOT BE LESS Than 2 individual scenes and NOT MORE THAN 3 (six) preprogrammed scenes. Each scene / low resolution moving light moving image low resolution video content shall be of minimum 5min each. Minimum 3 scenes/ low resolution moving light moving image low resolution videos.Approved Makes for Architectural/Themed/Decorative Iconic Lighting Automation (Helvar, Lutron, Madrix, Traxon, Pharos, Raylogic) This specification outlines the requirements for a control system suitable for managing multiple RGBW colour-changing fixtures and dimmable 3000K warm white landscape lights for the illumination of an iconic bridge. The system should accommodate regular weekday operations, weekend festivities, and special festive day lighting schemes. 1. **Control System Compatibility** - The control system must be compatible with either DMX/DMX-RDM based Madrix, ArtNet and Pharos systems. - Ability to integrate with DMX, Art-Net, and sACN protocols for RGBW fixtures.....
Excavation for foundation for loose and soft soil including sorting out and stacking of useful materials and disposing of the excavated stuff up to 50 meter lead. From 0.00 to 1.50 m
From 1.50 to 3.00 m.
From 3.00 to 5.00 m.
Filling with available excavated earth (excluding rock) in trenches, plinth, sides of foundation in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering.
Providing & laying rubble soiling (hand packing) on prepared surface and filling interstice with hard murrum including all material, spreading, watering etc completed as directed.
Carting and recarting of materials such as murum, earth, kapchi, gravel, brick bats, kankar, sand, debris etc. from the site to approved location, including loading, unloading, stacking and spreading etc. complete. i) 50m to 5 Km.
Providing and laying in situ machine mixed M-15 grade bedding concrete in foundation / below pile cap including dewatering, shuttering, compacting, curing etc. complete true to level and position as directed by Engineer and as per specification.
Providing and laying controlled cement concrete M40 for foundation and superstructure with vibrating, curing etc. complete excluding the cost of form work and reinforcement for RCC work stated below etc. complete at any height, as directed. Base slab
Column
Ground Beam, Floor beam, Ring beam
Providing form work of ordinary timber planking so as to give a rough finish including centring. Shuttering strutting and propping etc. Height of propping and centring below supporting floor to ceiling not exceeding 4M. And removal of the same for in including reinforced concrete and plain concrete work in : Base slab
Column
Ground Beam, Floor beam, Ring beam
Providing & fixing in position (Thermo mechanically treated bars) TMT Fe500D steel bars of various diameters for all RCC works as per detailed design & drawings and schedule including cutting, bending, hooking the bars, binding with 18 SWG GI wires or tack welding (only for piles) and supporting as required with all lifts and leads etc. complete including cost of all labour, materials, tools, plants, equipments etc. all complete as directed by Engineer and as per specification. (including anti-corrosive treatment to reinforcement with Fusion Bonded Epoxy Coating (FBEC) (To be taken as per the prevailing market rates.)
Providing and laying controlled cement concrete M40 for foundation and superstructure with vibrating, curing etc. complete excluding the cost of form work and reinforcement for RCC work stated below etc. complete at any height, as directed. Column
Floor beam
Providing form work of ordinary timber planking so as to give a rough finish including centring. Shuttering strutting and propping etc. Height of propping and centring below supporting floor to ceiling not exceeding 4M. And removal of the same for in including reinforced concrete and plain concrete work in : Column
Floor beam
Providing & fixing in position (Thermo mechanically treated bars) TMT Fe500D steel bars of various diameters for all RCC works as per detailed design & drawings and schedule including cutting, bending, hooking the bars, binding with 18 SWG GI wires or tack welding (only for piles) and supporting as required with all lifts and leads etc. complete including cost of all labour, materials, tools, plants, equipments etc. all complete as directed by Engineer and as per specification. (including anti-corrosive treatment to reinforcement with Fusion Bonded Epoxy Coating (FBEC) (To be taken as per the prevailing market rates.)
Brick work using common burnt clay building bricks including scaffolding, raking of joints, curing using first class bricks having min. comp. Strength 35 kg/cm2 of approved manufacturer in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional All bricks and shall be soaked in water for at least 24 hours before use. bricks used for masonry work shall be as available locally, but approved before start of work. volume of masonry to be measured for payment.
Providing & fixing LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Volumne of blocks erected to be measured for payment. R.C.C. coping of size-wall thickness x 100mm ht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontal bars and 6mm diameter at 200 c/c ties. R.C work not to be measured separately but included in rate.
Providing & fixing 150mm thick LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Area of blocks erected to be measured for payment. For wall thickness up to 150mm, R.C.C. coping of size-wall thickness x 100mm ht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontal bars and 6mm diameter at 200 c/c ties. R.C work not to be measured separately but included in rate.
Providing and laying 10mm thick in single coat CEMENT PLASTER in (i)Cement mortar 1:3 (1- cement:3-sand) at all height/all floors to internal surfaces of all elements, walls, R.C.C. work, Ceiling, including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete. a) Internal walls
b) Backing coat at places where glazed or ceramic tiles are to be fixed etc Final finished surface shall be little rough , so as it has proper bonding to paint putty.
Providing and laying 20mm thick SANDFACED CEMENT PLASTER of required grain finishing upto all height/all floors including grooves, pattas etc. in two coats having the the base coat of not less than 12 mm thickness in CM 1:3 (1-cement : 3-sand) & finished coat 8 mm thk, in CM 1:1 (1-cement : 1-sand) to external surfaces of concrete & masonry including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Rate shall include addition of “Impermo” water proofing compound or equivalent, providing, adding & mixing of fine fibrillated 100% virgin polypropylene fibers in cement mortar to form homogeneous mixture @125 gms per a bag of cement in both the coats of plaster, 12mm long fibers shall be used in first coat & 6mm long fibers shall be used in second finished coat. providing drip mould 40mm wide and 12mm thick in cement mortar 1:3 on soffit of chajjas, canopies, gutters etc.complete. as directions of Engineer in charge Complete. The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete.
FLOORING / DADO WORKS 600X600MM Vitrified tiles flooring Providing and laying approved make quality, colour, design and shade Antiskid Vitrified tile (conforming IS 15622) flooring 600mm x 600mm size in pattern as detailed in drawing or as directed by the PM. Tile to be bedded in cement sand mortar mix ratio 1:6 (1 cement : 6 Crush sand)having overall floor finish of 75mm thick including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.5 kg/sqm over bedding, joints to be cleaned and grouted with Laticrete 500 series sanded grout with Laticrete 1776 ad mix or similar product.of matching colour, curing, cleaning, protecting with K.N. Sheet concept till handing over etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the PM.
600x600mm Vitrified tiles dado Providing and fixing approved quality, colour, design and shade Vitrified tile 600mm x 600mm size of approved make (confirming to IS 15622) dado to walls/columns, as shown in drawing or as directed by the PM. Tile fixed over plastered masonry / RCC surfaces by using approved compatible adhesive (Bal / Laticrete suplerflex 335 or equivalent approved) of thickness as per manufacturer recommondation over plastered surface to correct line, level and plumb. Joints are well cleaned and grouted with matching colour polymer based approved quality readymade grout with Laticrete 500 series sanded grout with Laticrete 1776 ad mix or similar product.of matching colour and cured, cleaned, junctions with plaster finished smooth, etc. all complete at all heights and leads to the satisfaction of the PM.
Kota stone dado
Providing and laying 25mm thick machine cut, machine polished Kota stone flooring in uniform colour, pattern and size as detailed in drawing or as directed by the PM. Stone to be bedded in mechanically mixed cement sand mortar mix ratio 1:6 (1 cement : 6 sand) overall 20mm thick including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.5 kg/sqm over bedding, to required line, level; joints to be cleaned and grouted with matching colour approved quality readymade grout, curing, cleaning, polishing, protecting etc. all complete at all heights and leads to the entire satisfaction of the PM . wash basin counter - granite
Providing and fixing of 18mm thick machine cut, machine polished Granite stone of approved quality wash basin counter top about 600mm wide fixed and bedded over 20-25mm thick kadappa stone and about 50mm wide mirror polished Granite fascia all as detailed in drawing. Stones for fascia fixed with epoxy adhesive; exposed faces / edges, rounded / chamfered, mirror polished etc. complete to the approval of the PM. Including 18mm thick approved 675mm high plywood vertical support, shutter and 550mm wide bottom finished with 1.0mm thick laminate on both sides. All junctions shall be sealed with silicon sealant. Further to include required MS framing with primer and paint finish, drilling, cutting of holes, SS pins, anchors, clamps, finishing junctions with plaster, necessary hardware for shutter etc. complete as shown in the drawing and to the entire satisfaction of the PM. Ticket counter - granite
Providing and fixing of 18mm thick machine cut, machine polished Granite stone of approved quality ticket counter top about 600mm wide fixed and bedded over 20-25mm thick kadappa stone and about 50mm wide mirror polished Granite fascia all as detailed in drawing. Stones for fascia fixed with epoxy adhesive; exposed faces / edges, rounded / chamfered, mirror polished etc. complete to the approval of the PM. Including 18mm thick approved 675mm high plywood vertical support, shutter and 550mm wide bottom finished with 1.0mm thick laminate on both sides. All junctions shall be sealed with silicon sealant. Further to include required MS framing with primer and paint finish, drilling, cutting of holes, SS pins, anchors, clamps, finishing junctions with plaster, necessary hardware for shutter etc. complete as shown in the drawing and to the entire satisfaction of the PM. Urinal partitions
Providing and fixing Urinal partitions made out of 18mm thick approved Granite stone, partitions to be machine cut and machine polished (both sides) in one piece and edges polished and semi rounded of size 525mm x 900mm size (exposed size). Stone shall be fixed in wall securely and grouted and finished in cement sand mortar 1:3 (1 cement : 3 sand) fixed to correct line and level including chasing in wall, curing, cleaning, exposed edge of stone rounded / chamfered and polished etc. all complete as shown in the drawing and to the satisfaction of the PM. Granite door frames
Providing and fixing 18mm thick machine cut, machine polished approved granite double patti frame (about 150mm wide) of shape and size of approved quality and colour as shown in the drawing etc. Stone shall be fixed with approved adhesive on back, to correct line, level and plumb. Joints are well cleaned grouted with matching colour approved readymade grout, curing, polishing, cleaned and where specified or shown in drawing exposed edge of stone rounded / chamfered and polished all complete to the satisfaction of the PM.
Chemical water proofing to toilet Designing, providing and laying proprietary chemical waterproofing system consisting of two coats of acrylic polymer modified cementitious waterproof coating (shall contain a liquid polymer component and a cementations powder component, which shall be mixed as per manufacturer’s instructions and applied over prepared concrete surface coverage @ 12-14 m2 per pack in 2 coats) over the entire toilet sunken slab and walls upto 1 M height from FFL as approved by the PM and as directed by the approved manufacturer of waterproofing coating, with sandwiched fibre mesh and protective screed. The work shall include cleaning of surface, grouting porous surfaces including making ‘V’ grooves at junctions, cracks with non shrink crystalline base cementitious grout etc. Further including horizontal and vertical surfaces protected with 20mm screeding in 1:4 mortar (1 cement : 4 sand), finished in ready to receive Architectural finish, in correct line, level and plumb, curing, grouting, testing, etc. all complete to entire satisfaction of the PM, contractor to provide guarantee for 10 years Rs.100/- stamp paper in approved proforma.
Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6- Graded brick bat aggregate 40mm normal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth
Providing material, Labour and equipments for Providing and laying integral Cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations : a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer in charge over the RCC Slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge over 20mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junction of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge. d) Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer in charge : Including Khurra & Gola work with average thickness of 120mm and minimum thickness at Khurra as 65 mm etc. complete as directed by Chief Engineer in charge.
Providing and fixing Toilet cubicle system made out of High Pressure Laminate (HPL) (Merino or equivalent), compact panels including doors, pilasters & Intermediate panels as decided by PM / Architect including all SS (SS-304) hardware. A self-supporting 12mm thick panel for interior applications, based on thermo setting resins, homogeneously reinforced with wood-based fibres and manufactured under high pressure and high temperature, giving a homogeneous panel with a closed structure, without pores in either the surface or the core of Marino or equivalent approved system with standard hardware as approved all complete as per recommendation of manufacturer and to the entire satisfaction of PM.
Providing and fixing factory made 30mm thick wooden flush door shutters conforming to IS 2202Part I, shutter shall be manufactured with exterior quality synthetic adhesive forming marine ply surfaces, internally lipped as manufactured or equivalent approved make. Further shutter shall be finished both side with minimum 1mm thick laminate of approved make, shade and colour and design with hot pressed at factory, edges of shutters shall be provided with 6mm thick approved teak wood beading using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with melamine polish, etc. (Beading kiln seasoned, anti-termite treated) including ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. a) D1 1200x2250mm
b) D2 1000x2250mm
Notes for Hardware : Supplying and fixing heavy quality fixtures and fittings for doors, windows, ventilators, partition wall, cabinets with necessary screws, nails, machine pins etc at all floor/ all levels/ all heights complete. Sample shall be approved by Architect before execution. As per description, SS hardware shall be of 304 grade or 316 grade as per item description and as per approved sample. The fixture & fastenings shall be provided as under : Providing material and labour for fixing single/ double action hydraulic floor spring with SS cover plate & adjustable concealed casted top pivot (two piece) and bottom strap of approved make for wooden/ aluminium doors of specified capacity with minimum one year guarantee. Rate shall be inclusive of cutting of floor neatly, grouting the floor spring & cleaning/ polishing the floor & maintaining in good working condition until defect liability period. In case of Aluminium shutter bottom arm of floor spring & top pivot shall be firmly fixed in the aluminium members using required size of teak wood by making rabbet in the wood. The Floor Spring shall conform to EN 1154. a) Hold open having for shutter width upto 1200mm with standard spindle and cover plate. Closing force complying with EN 1154 2-4
Providing material and labour for fixing hydraulic rack and pinion door closer with standard arm (Silver finish) with screws to pivoted/ hinged door of approved make for specified door width with minimum one year guarantee. All adjustment screws face fixed. Rate shall be inclusive of fixing with using the template as per manufacturer’s specification & maintain in good working condition until defect liability period. The door closer shall conform to EN 1154 standard. a) with standard/ hold open arm with two independent closing valves and latching speed adjustable by arm without mounting back plate, Closing force complying with EN 1154 2 - 4 for up to 700 mm door shutter width
Providing and fixing 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm, in SS 304 and in SSS finish. Suitable for door weights upto 120kgs. Template Drilledstainless steel screws etc. complete of dorma or approved make and as approved by Engineer In Charge.
Providing and fixing EURO PROFILE DOUBLE CYLINDER - 60MM in stainless steel satin finish of approved make with necessary screws etc. complete
Providing and fixing approved Wall mounted door stop with coat hook in SSS finish with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer In Charge.
Providing and fixing pull Handle back to back with adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =300mm, 22mm dia, -SS304 with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer In Charge.
Providing & Fixing Male Sign Plate For Wc Application With Fixing Screws Size 125 X 125Mm, Rounded Corners In Ss 304 Satin Stainless Steel Finish. Marking In Black ( 1Mm Thick ) with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer In Charge.
Providing & Fixing Female Sign Plate For Wc Application With Fixing Screws Size 125 X 125Mm, Rounded Corners In Ss 304 Satin Stainless Steel Finish. Marking In Black ( 1Mm Thick ) with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer In Charge.
Providing material & labour for Artistic Internal Wall painting (two coats) with Luxury Emulsion of approved brand and manufacture including suitable primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. as directed by engineer in charge complete. One component waterborne 100% pure acrylic interior eggshell emulsion that must offer protection against different varieties of bacteria and fungus. Paint should free of HCHO, APEO and have crack bridging property of min 0.9 mm with class 1 flame spread resistance The product shall have a Volume Solids of minimum 35% The product shall be independently tested and approved for properties alike resistance to bacterial and fungal species, crack tolerance and flame spread resistance. The coating shall contribute to satisfying the following credit(s): - Indoor Environmental Quality (IEQ) under LEED® 2009 - Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4......
Supplying & Providing two coat of primer and two coats of TEXTURE PAINT, ANTIFUNGAL PAINT, water proof, dust proof Paint on Exterior Surfaces at all heights of surfaces. One component waterborne 100% pure acrylic emulsion that offers protection against concrete carbonation with an R Value of min 600m and an equivalent concrete layer thickness value of min 150cm. Paint should have crack bridging property of min 1.85 mm with Solar Reflective index of min 110 and IR reflectance property. The product shall have a Volume Solids of minimum 35% The product shall be independently tested and approved for properties alike Carbon Dioxide Diffusion resistance, resistance to chloride diffusion, crack bridging and liquid water/ vapour transmission as well as SRI properties. The product can be like Jotashield WaterXtreme Topcoat of Jotun Paints or approved equivalents. Two Coats of above paint should be applied using a conventional Roller / Airless spray at the site after application and curing of applied Primer. including cleaning, preparing the surface, applying primer - scraping by sandpaper, scaffolding etc. including - (a) All surface preparation, suitable number of base coats required, primers and suitable finishing to the complete satisfaction of the Engineer in Charge, (b) Scaffolding and all leads and lifts,(c) Proper curing in between the two subsequent coats, (d) Touch ups to the paint after the scaffolding is removed, (e) All measurements for paints to be as per IS-1200. f) Minimum Guarantee of Ten Years Waterproofing and Paint performance for all external paints by manufacturer . For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. Make - Asian Paint Ultima Allura Torino, Jotun Jotashield Tex Fine OR Equivalent.
ALUMINIUM WORKS -Doors and Windows work Providing material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Glazing shall be paid as seperate item. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required, etc as per directions of Engineer in charge Complete. Make:- Jindal or equivalent as approved by Engineer-in-charge
Providing material and labour for fixing 6mm thick Clear Normal Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.
Preparing shop drawings, obtaining Structural Consultant's approval, supplying, fabricating in accordance with IS:800, delivering at site, hoisting and fixing in position at all locations and levels, including all temporary staging and supporting work and making all structural steel work in accordance with the design, drawings prepared by the Consultants. The rate of steel work shall include cutting, grinding, machining, assembly, welding, jointing, of single / building up new sections with anchors, angles, beams, canopy, supports, column, trenches angel protections, trench covers etc., cost of fasteners (nuts, bolts and washers), pre-heating the sections to temperatures up to 250oC if thickness of the section is equal to or more than 25 mm. Fabrication will involve connections using plates, channels and angles, gusset plate, foundation bolts, cleats, fasteners, stiffners etc. as per drawing, steel conforming to IS : 226 and IS : 2062 with minimum yield strength of 250 Mpa and upto 355 Mpa. The rate shall also include one coat of zinc rich primer after properly cleaning the steel surface with wire brush and mild acid solution followed by washing with water and drying the surface completely, to be applied to individual fabricated parts of the structure prior to their erection & assembly in their final place. The rate shall also include the synthetic enamel paint system in approved shade and of approved make as per recommendations of paint manufacturer to the approval of PM. a) All structural steel in the form of plates, angels, channels, RS joists etc. shall conform to IS : 2062.
PROVIDING AND FIXING FOLLOWING SANITARY FIXTURES AND FITTINGS AS PER DETAIL DRAWING. WALLHUNG WITH SEATCOVER & SLIP IN CONNECTOR
HEALTH FAUCET
CONCEALED TANK W/O FRAME
DUAL FLUSH PLATE
TABLE TOP BASIN WITH TAP HOLE
FAUCET FOR BASIN
WASTE COUPLING
P TRAP FOR BASIN
ANGLE COCK
WALLHUNG BACK INLET URINAL
DC TYPE SENSOR FOR URINAL
FLOOR DRAIN
TOILET PAPER
SOAP DISH
TOWEL RING
Providing & fixing LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Volumne of blocks erected to be measured for payment. R.C.C. coping of size-wall thickness x 100mm ht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontal bars and 6mm diameter at 200 c/c ties. R.C work not to be measured separately but included in rate.
Providing and laying 20mm thick SANDFACED CEMENT PLASTER of required grain finishing upto all height/all floors including grooves, pattas etc. in two coats having the the base coat of not less than 12 mm thickness in CM 1:3 (1-cement : 3-sand) & finished coat 8 mm thk, in CM 1:1 (1-cement : 1-sand) to external surfaces of concrete & masonry including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Rate shall include addition of “Impermo” water proofing compound or equivalent, providing, adding & mixing of fine fibrillated 100% virgin polypropylene fibers in cement mortar to form homogeneous mixture @125 gms per a bag of cement in both the coats of plaster, 12mm long fibers shall be used in first coat & 6mm long fibers shall be used in second finished coat. providing drip mould 40mm wide and 12mm thick in cement mortar 1:3 on soffit of chajjas, canopies, gutters etc.complete. as directions of Engineer in charge Complete. The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete.
Providing and fixing 18 mm thick gang saw cut, mirror polished, Premoulded and prepolished, machine cut for kitchen platforms, vanity counters, coping, tread, landscaping, window sills, facias, parapet top and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels, as per sample approved by Engineer in-charge. Necessary MS/ SS frame structure for fixing the stone counter shall be paid in relevant tender item. i) Ticket counter
ii) Kitchen counter
Providing and fixing 12mm thick Engineered homogeneous wooden flooring of approved make, type, pattern and shade etc as given by the Engineer and as per manufacture’s specification confirming to British Standards BS EN 14904. Rate shall be inclusive of 3mm mm thick foam base underlay sheet as sound barrier and all the accessories like edge strip, joining strip, quarter strip, moulding strip, corner strip, etc. required as per design. Uniform gaps should be left on all sides to allow expansion and contraction of material. Flooring planks shall have micro bevel edges with lock n fold locking installation system. The gaps are covered with the help of accessories finished in all respects as per the manufacturer's specifications. The floor shall be laid in place with matching original skirting of approved height and profiles as approved and as per recommendations of approved manufacturer over base of existing flooring. The contractor shall get the sample and pattern approved by the PM before execution. Installed area of wooden flooring shall be considered for payment. Rate includes cost of foam sheet, wooden flooring, skirting etc. complete. For the purpose of payment, the area of wooden flooring only will be measured for payment.
Supplying & Providing two coat of primer and two coats of TEXTURE PAINT, ANTIFUNGAL PAINT, water proof, dust proof Paint on Exterior Surfaces at all heights of surfaces. One component waterborne 100% pure acrylic emulsion that offers protection against concrete carbonation with an R Value of min 600m and an equivalent concrete layer thickness value of min 150cm. Paint should have crack bridging property of min 1.85 mm with Solar Reflective index of min 110 and IR reflectance property. The product shall have a Volume Solids of minimum 35% The product shall be independently tested and approved for properties alike Carbon Dioxide Diffusion resistance, resistance to chloride diffusion, crack bridging and liquid water/ vapour transmission as well as SRI properties. The product can be like Jotashield WaterXtreme Topcoat of Jotun Paints or approved equivalents. Two Coats of above paint should be applied using a conventional Roller / Airless spray at the site after application and curing of applied Primer. including cleaning, preparing the surface, applying primer - scraping by sandpaper, scaffolding etc. including - (a) All surface preparation, suitable number of base coats required, primers and suitable finishing to the complete satisfaction of the Engineer in Charge, (b) Scaffolding and all leads and lifts,(c) Proper curing in between the two subsequent coats, (d) Touch ups to the paint after the scaffolding is removed, (e) All measurements for paints to be as per IS-1200. f) Minimum Guarantee of Ten Years Waterproofing and Paint performance for all external paints by manufacturer . For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. Make - Asian Paint Ultima Allura Torino, Jotun Jotashield Tex Fine OR Equivalent.
Excavation for foundation for loose and soft soil including sorting out and stacking of useful materials and disposing of the excavated stuff up to 50 meter lead. From 0.00 to 1.50 m
From 1.50 to 3.00 m.
Filling with available excavated earth (excluding rock) in trenches, plinth, sides of foundation in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering.
Providing & laying rubble soiling (hand packing) on prepared surface and filling interstice with hard murrum including all material, spreading, watering etc completed as directed.
Carting and recarting of materials such as murum, earth, kapchi, gravel, brick bats, kankar, sand, debris etc. from the site to approved location, including loading, unloading, stacking and spreading etc. complete. 'i) 50m to 5 Km.
Providing and laying in position Ready Mixed M-150 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained)
Providing and laying in position Ready Mixed M-400 grade concrete for reinforced cement conctere work , using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash(Min cement level as per latest IS 456 shall be maintained)
Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4.8 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete.
Provision of aluminum formwork, including centering, shuttering, strutting, propping, and groove cutting, to achieve a smooth finish as per the drawing. The height of propping and centering will be from the supporting floor to the ceiling. This includes the removal of formwork after the completion of in-situ reinforced and plain concrete work (C) Vertical surface such as walls (any thickness) partitions and the like including attached buttresses & string course & the like. Rate shall be inclusive of providing grooves etc.
Provision of aluminum formwork, including centering, shuttering, strutting, propping, and groove cutting, to achieve a smooth finish as per the drawing. The height of propping and centering will be from the supporting floor to the ceiling. This includes the removal of formwork after the completion of in-situ reinforced and plain concrete work (B) Flat surfaces such as soffits of supspened floors slabs Landings and the like. (1) Floors etc. upto 200 mm in thickness.
Provision of aluminum formwork, including centering, shuttering, strutting, propping, and groove cutting, to achieve a smooth finish as per the drawing. The height of propping and centering will be from the supporting floor to the ceiling. This includes the removal of formwork after the completion of in-situ reinforced and plain concrete work. (H) (1) Sides and soffits of Beams Beam Haunchings cantilevers Girders Bressumers and Lintels not exceeding 1 M. in Depth.
Providing & fixing in position (Thermo mechanically treated bars) TMT Fe500D steel bars of various diameters for all RCC works as per detailed design & drawings and schedule including cutting, bending, hooking the bars, binding with 18 SWG GI wires or tack welding (only for piles) and supporting as required with all lifts and leads etc. complete including cost of all labour, materials, tools, plants, equipments etc. all complete as directed by Engineer and as per specification. (including anti-corrosive treatment to reinforcement with Fusion Bonded Epoxy Coating (FBEC) (To be taken as per the prevailing market rates.)
Extra for Colour Concrete: Extra over concrete for providing and adding colour pigment as admixture of approved make and shade as per manufacturer's specification in specified grade of plain/ reinforced cement concrete for any type of element as per drawing and as approved by Architect and as directed by engineer in charge. Rate shall be for actual volume of concrete cast with colour pigment.
Section Feeder Panels Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning double compartmentalized Street light control panel with IP 65 protection & Enclosure should be powder coated fabricated from 10 Gauge M.S. sheet & folded channel totally enclosed cubical type with made out of Modular Panel Box System of high quality polycarbonate thermoplastic, Degree of Protection IP 65, in accordance with IEC 60 529, type tested in accordance with IEC 60 439 – 1. with pad lock arrangement. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Architect/ Consultant. All civil work including RCC platform for street light panel should be in scope of Electrical contractor complete in all respect as per detail drawing and directed by engineer in charge. with the 600 mm height MS angle covered stand. The panel board shall be made up of high quality polycarbonate thermoplastic, shock proof, anti-corrosive, acid & chemical resistant, fire retardant, self extinguishing, highly impact resistant, halogen free, silicon free, recyclable, having internally embedded gasket. The switchboard (panel) shall have provision for future expansion & shall be modular in construction. The bus bars shall be connected with C type clamps without any drilling on the bus bars. The panel shall be in accordance with IEC 61 439 – 1 (Fully TTA). The Degree of Ingress Protection shall be in accordance with IEC 60 529. SITC of the IP 65 Section feeder panel for the Lighting Consisting of following Incoming : 200 Amp FP MCCB with the spreader link with in built earth fault relay R-Y-B-On-Off indicating Lamp with control fuse. Busbar : Set of 200 A. FP tinned copper busbars of EC. grade & adequate capacity, size & insulated with colour tape & should be tined at all joints. Auto/Manual bypass switch with indicating lamp Meter : VAF meter equivalent to Enercon make ELF 3259 with 125/ 5 A Class 1 ct. Outgoing : MCB's Should be of 10 KA. 40 Amp. FP MCB : 15 nos. 6 -32 Amp. FP MCB : 4 nos. 6 - 32 amp. DP MCB : 5 nos. 5 KVAR Capacitor with the 40 amp TP capacitor duty contactor with the 10 minute time delay relay. Panel Should Have lockable Space to incorporate the 2 nos of the 3 phase energy meter with its main switches with separate cable entry with separate compartment & Separate door.
SITC of the IP 65 Sub Section feeder panel with for the Street Lighting Consisting of following Incoming : 40 Amp FP MCB R-Y-B-On-Off indicating Lamp with control fuse. Busbar : Set of 40 A. FP tinned copper busbars of EC. grade & adequate capacity, size & insulated with colour tape & should be tined at all joints. Auto/Manual bypass switch with indicating lamp Meter : VAF meter equivalent to Enercon make ELF 3259 with 40/ 5 A Class 1 ct. Outgoing : MCB's Should be of 10 KA. Timer Equivalent to Theben make Astronomical type with the battery back up : 2 nos. 32 amp. FP Power Contactor : 2 nos. 6 - 32 amp. DP Power Contactor : 12 nos. 6 -32 Amp. FP MCB : 2 nos. 6 - 32 amp. DP MCB : 12 nos. 5 KVAR Capacitor with the 40 amp TP capacitor duty contactor with the 10 minute time delay relay. Panel Should Have lockable Spacefor DMX controller and all kind of accessories with its main switches with separate cable entry with separate compartment & Separate door.
SITC of IP-68 Junction Box - 130mm x 180mm with gell & suitable required connector
SITC of IP-69 Junction Box - 155mm x 210mm with gell & suitable required connector
SITC of IP-69 Junction Box - 225mm x 295mm with gell & suitable required connector
Point Wiring Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. with medium class Rigid PVC pipe and accessories
Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. with medium class 25 MM DIA Rigid PVC pipe and accessories
Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.
Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories
Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire
Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire
Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 4.0 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make with concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.
MAINS : ( not for Point wiring ) Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 4 nos. of 6 sq mm Cu. FRLS flexible wires with 2 nos 2.5 sqmm Cu. FRLS flexible wires
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 4 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS flexible wires
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS flexible wires
Distribution Board-TPN Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.) MCB SITC of the MCB's ( 10 KA ) Timers , & Contactors With the Dinrail Channel
providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark
Miniature circuit breaker single pole suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark 6 to 25 A SP MCB
Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 A DP MCB
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 to 32A / 30mA/100 mA DP ELMCB
40 A / 100 mA DP ELMCB
Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat.III
Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (b) 40 Amp. Cat.III
Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32A FP MCB
Supplying & erecting power contactor for time switch complete erected as per direction Cat III [B] 2 pole 250V 32 Amp.
Supplying & erecting power contactor for time switch complete erected as per direction Cat III [D] 4 pole 440V 40 Amp.
Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.
Excavating hard rock or bituminous road (B.T.) / RCC ROAD by chiseling for laying pipes & Other Purpose & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer Incharge.
Making trench in soft soil of suitable width of 90 cms deep from the final ground level or road level for laying cable or locating the fault all over the run and backfilling the same & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer Incharge.
Making trench in Hard murum / Tar Road of suitable width of 90 cms deep from the final ground level / road level for laying cableor locating the fault all over the run and backfilling the same and making the surface proper. by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer Incharge.
Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks shall be provided.
Driling the road without breaking the road surface (Asphalt) for laying of cable for feeding power supply by making Suitable size of holes at both ends complete. (A) Up to 100 mm bore dia
Driling the road without breaking the road surface (Asphalt) for laying of cable for feeding power supply by making Suitable size of holes at both ends complete. (B) Up to 150 mm bore dia
Construction of brick masonery pulling chamber 1250 mm x 1250 mm inside clear size and depth upto 1.2 meter with 350 mm thick masonery in cerment mortar proporation 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minmum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer Incharge complete in all respect.
Providing & laying. Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II ) Anti Rodent type with necessary connecting accessories of same material at required depth for laying of cable. below ground / road surface for enclosing cable with Excavation and backfilling the same to make ground as per original. (A)50 mm dia
(B)90 mm dia
(C)120 mm dia.
Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as per IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (E) 90 mm inner Dia
(F) 110 mm inner Dia.
Providing and erecting 1.5 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection. For erecting concealed / Open in wall/slab along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. (A) 25mm
Providing & erecting PVC 1mm thick Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2) 25 mm
Providing & erecting PVC 1mm thick Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (3) 32 mm
Providing & erecting PVC 1mm thick Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (4) 40 mm
Cables Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 95 sq.mm x 3.5c Al. XLPE Arm. Cable
70 sq.mm x 3.5c Al. XLPE Arm. Cable
50 sq.mm x 3.5c Al. XLPE Arm. Cable
35 sq.mm x 3.5c Al. XLPE Arm. Cable
25 sq.mm x 4 c Al. XLPE Arm. Cable
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (B) 4 core 16 Sq. mm
(A) 4 core 10 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (A) 3 core 2.5Sq. Mm
(B) 3 core 4 Sq. mm
(C) 3 core 6 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 2 core 2.5 Sq. mm
(B) 2 core 4 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 2.5 Sq. mm
(B) 4 core 4 Sq. mm
(C) 4 core 6 Sq. mm
Cable Termination SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. Note : All Cable should be with suitable IP65 PVC / DC Gland 95 sq.mm x 3.5c Al. XLPE Arm. Cable
70 sq.mm x 3.5c Al. XLPE Arm. Cable
50 sq.mm x 3.5c Al. XLPE Arm. Cable
35 sq.mm x 3.5c Al. XLPE Arm. Cable
25 sq.mm x 4 c Al. XLPE Arm. Cable
16 sq.mm x 4 c Cu. XLPE Arm. Cable
10 sq.mm x 4 c Cu. XLPE Arm. Cable
6 sq.mm x 4 c Cu. XLPE Arm. Cable
4 sq.mm x 4 c Cu. XLPE Arm. Cable
SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, double compression type Brass glands with earthing. Note : All Cable should be with suitable IP65 PVC / DC Gland 6 sq.mm x 3 c Cu. XLPE Arm. Cable
4 sq.mm x 3 c Cu. XLPE Arm. Cable
2.5 sq.mm x 3 c Cu. XLPE Arm. Cable
Cable Tray & Fabrication Providing and fixing approved make Perforated C type cable tray with cover and proper sealing for security and to control rodent. Made from sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support( included) as per Specification and as per instruction of engineer in charge.. (3) 150 X 50 X 1.6 mm Thick
(5) 300 X 50 X 2.0 mm Thick
(6) 450 X 50 X 2.0 mm Thick
Fabrication Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles,square,round, flats, bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one coat of red oxide, Primer, PU Painting and any kind for specilized fabrication with erection on site as per direction of Consultant/ engineer in charge with necessary grouting, cementing, plastering & finishing complete.
Supplying under floor pregalvanised corrosion proof rectangular sheet steel cable trunking of 1.6 mm thick having with stand point load up to 1.33 Ton & free from seepage of concrete of screed water with all accessories,Junction Box,Joints as required and demanded by engineer-incharge and laying/erecting as per OEM guidelines and as per instruction of engineer incharge having following size of dimensions and No of compartments (W x D x T) Cat-III [10] 150mm x 38mm x 1.6mm with Three Compartments
UPS Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger with IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160- 270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (D) 5 KVA with 1Hr Backup Light Fixtures & Accessories Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast, ignitor & power factor improvement capacitor etc are prewired upto the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaire should be click fix & foolproof & require use of no tools. Mounting options should be for both lateral as well as pole top mounting Note : All Outdoor Fixture should be minimum IP66
Exhaust Fans : Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.
Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [A] 305 mm dia 900 RPM
Providing suitable M.S. louver shutter of the Exhaust fan.
Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit with earthing provision, copper winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374- 2019), THD < 10%, with remote unit for Speed Control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and rectifier circuit with surge, over current and overload protection , 50 Hz, Single phase AC Supply, earthing etc. Complete as required.[ Make shall be approved by Engineer in Charge] (B) 1200 mm Sweep (48")
Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.
SITC of Decorative Light Fixture (120 Watt) - ( Applicable tolarance) LED Decorative Luminaires, Symmetric/Assymetric BIS approved ( alongwith BIS certification of model streetlight family confirming to IS 10322/IEC60598 & LM79 parameters as per tender specs),.Body of the fixture must be in two parts and fixture opening of the fixture is from front side for the ease of operation . The protector is made of single piece injection moulded polycarbonate Protector grade with UV resistant IK 09 ( Confirmed by IEC60598 report from Third party NABL approved lab) . ring Permanently sealed optical compartment with IP66 protection.( Confirmed by IEC60598 report from Third party NABL approved lab). Luminaire offers tool free access to gear compartment with IP65 protection( Confirmed by IEC60598 report from Third party NABL approved lab) . Luminaire can be installed as a suspended luminaire with 1 inch BSP stainless steel pipe with 2 chuck nuts is provided..The luminaire must be provided with Air vent plug in optical compartment.The luminaire is equipped with PC lenses with wide photometry for increased pole spacing. The luminaire is provided with disconnector to avoid electrical shocks. Easy access to control gear compartment by opening special draw latch with zinc plated material and hinge kind of arrangement. Fixture is having external surge protection of 10KV. Electronic driver is having power factor>0.90*, THD<15*%, CRI>70 and input voltage range from 120-227V AC at 50Hz. system efficacy of minimum 120 lm/watt for clear protector (Confirmed by LM79 report from Third party NABL approved lab) in CCT range of 4000K as per ANSI. presented with Dialux report and IES file of the luminaire System life of 50000 burning hours with 70% of initial lumens maintained. Luminaire is suitable for operating temperature (Ta) from -10° to 50°C.
SITC of Lead 5P DMX Cable of 2 mtr. Length of Philips Make ZXP399 Lead 5P DMX cable 2m / LT Make / La-Martini Make The cabel should be with all required accessories and as per specifications.
SITC of Jump 5P DMX Cable of 2 mtr. Length of Philips Make ZXP399 Jump 5P DMX cable 2m / LT Make / La-Martini Make The cabel should be with all required accessories and as per specifications.
SITC of Lead Cable as per specification of Philips make ZXP399 Lead 5P DC/DMX cable / LT Make / La martini make. The cable should be with IP67 Connector.
SITC of DC/DMX//RDM Jumper cable as per specification of Philips make ZXP399 Jump 5P DC/DMX cable / LT Make / La martini make. The cable should be with IP67 Connector.
SITC of 4C x 1.0 sq.mm. cu Arm. Cable - Shielded
SITC of 3C x 1.5 sq.m. cu. Arm Cable Shielded
SITC of Armoured Cat-6 Cable Shielded of Legrand / Panduit make with termination as per TIA
SITC of Single Mode OM 4 - 6 Core Armoured Fibre Cable and its required connections as per TIA at Rack / switch level, Including all accessories and connection and connectors
Supply, Installation, Testing And Commissioning of Layer 3 Managed 10 Gigabit switch with 12 # 10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port of CISCO make / HP make
SITC of 4U Outdoor Rack of Legrand / Walrack make
SITC of 8 Mtr. Height Heritage Pole with All accessories
SITC of Double Arm Decorative Bracket as per Drawing with all accessories
CCTV Camera Supply , Installation, Testing & Commissioning of 4MP AI based camera with built in video analytics in SS 316 Body. Builin Micro phone & 8GB memory card. IP66. for marine environment. Make : Pelco, Tyco, Penasonic
Supply Installation Testing & Commissioning of Network Storage Manager(NSM) supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec. System proposed shall have scalability of 4 to 150 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF, Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity.
Supply, Installation, Testing & Commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's licenses upto 200 cameras & 3 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall support iLIDS certified Analytics like Licence plate recognition and intrusion/LoiteTrace.
Intel® Core™ latest generation, 4.0 GHz or better, Minimum 32GB RAM, Minimum 512 GB separate SSD hard drive for OS, DVD-R/W, 6 GB/s SAS/SATA RAID Card, RAID 1, 5, 10. 2 NIC cards supporting network throughput of 256 Mbps/425 Mbps for Incoming/outgoing, Graphics Adapter - Intel®IRIS XE Graphics or equivalent for local client GPU rendering support, Windows Server 2019 (64-bit OS versions recommended), Microsoft SQL Express 2012. Video rated or Enterprise drive, 7200 RPM SATA/SAS recommended, Video Monitor Resolution- 1280x1024 pixels, 32 bit with keyboard and mouse. The NSM shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items, as required.
Supply, Installation & Commissioning of NVMS workstation/PC with minimum Intel Core i7-12th Generation, 3.4GHz, 8GB RAM, Windows 10 Professional (64 Bit) OS, DVD R/W, Integrated Intel HD graphics 530 and NVIDIA Quadro NVS 315 1 GB PCIE x 16 LP supporting 4 Monitors. The NVMMS shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, storage, accessories etc., civil, electrical works & peripheral items, as required as per specification in Annexure A at site of work inline with the Engineer in Charge instructions..
Design, Supply , Installation, Testing & Commissioning of Central command station with 128 ch. Video management server with face detation , people counting & line crossing analytics. IP media playter & paging console for anoouncemeny & background music. Two way talk back responce panel
Supply, Installation, Testing And Commissioning of 55" 4k UHD resolution Monitor - 120 HZ for viewing the cameras
Supply, Installation, Testing & Commissioning of Industrial 8 Port10/100/1000 Base-T with 2 x 10G SFP+ ports Managed Switch.Each port should provide 90W of PoE Power, should have internal redundant power supply,Safety Standards like UL; EN; IEC;EMC; RoHS.
Supply , Installation, Testing & Commissioning of outdoor marine rated weatherproof low profile high quality modular line array speaker with 16 nos. of 1.5 inch driver supports 128 Hz - 18 kHz at 110 dB SPL. POE amplified Speaker with 5 years warranty. Make : Yamaha, NEXO, Uniteco
Supply , Installation, Testing & Commissioning of Two way talk back speaker & microphone using " push to talk" as a emergency communication & help to central server control room.
Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 24 # 10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port.
Supply, installation, testing and commissioning of 24 Port loaded Patch Panel
Supply, installation, testing and commissioning of Patch Cord-1m
Supply & Laying of Cat6A armoured cable for Speakers, Camera & PTT console from network switch.
Supply & Laying of 6 core Outdoor OS2 SM armoured cable for Server room connectivity from network switch.
Supply , Installation, Testing & Commissioning of 4 Meter Modular Smart Pole meter with integrated network switch, 180 degree coverage full frequency speaker, Dual lens coverage of 180 degree camera of 4MP & Push to talk emegency buttim on board. Ring / Triangle light with 60 watt power at 4500CCT giving 160 LM/ Watt output. IP66, IK08. Aluminium / SS 316 pole with marine grade powder coating. 5years warranty. Plate Type Earthing Supplying & erecting funnel type earthing having earth plate of following size burred in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per drawing) with following specification
(C) with 60 x 60x 0.315 cms. Copper earth Plate
(B) With 45 x 45 x 0.35 cms. C.I. earth plate
Supplying & erecting in earthpit of minimum bore dia. 225mm size , approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of Copper Pipes having Outer pipe dia of 50mm having , Inner pipe dia of 40 mm , connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (a) For Electrical Installation up to 440V in normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos Bag of 15 Kg.
Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel) Supply and laying required size Cu/GI. earthing strips for interconnecting the earthing stations, panels, section piller etc. in built up trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with : a) Fixing accessories. b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes.
Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.
Providing and erecting Annealed bare Copper wire 8 to 16 SWG./ Cu, Strip including all accessories
No.8 gauge bare GI. earth wire
D.G. SITC of 82.5KVA (66KW), Diesel Generating Set comprising of Air cooled Engine @ 1500 RPM coupled with 3Phase, 415 Volts, 50 Hz, 0.8 pf Alternator mounted on a base frame along with Fuel Tank, Battery with leads, first fill of lubricating Oil, Engine Safeties & Protections, Anti Vibration Mounting Pads, Standard Control Panel and Acoustic Enclosure as per the CPCB-IV Norms. (75dBA at 1 meter in free field conditions.
Liason / Follow UP with Supply Co. Filling the necessary application to supply co. following up and getting the supply filling the necessary test report to the supply co. inclusive. All official fees including securitydeposits will be paid by the client and out of pocket expenses shall be of contractor.
Providing and erecting approved make split air-conditioning unit consisting of copper condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas charging, 15A plug top & Remote Control) with necessary core cutting. For 4/5 star Rating of current year [a] For 1 Ton Capacity
Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR capacity erected with necessary hardware materials as directed.
Supplying and erecting insulated pair of soft copper tubing open or concealed including power and control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity
Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(C) 32mm
Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(D) 40mm Wash Out Pipe
Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(E) 50mm Wash Out Pipe
Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(F) 75mm ( Waste Pipe & Rain & Balcony Drain)
Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm ( Rain & Balcony Drain)
Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.
Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.
Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.
Providing and fixing toilet paper holder.(A) C.P. Brass
Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (i) 15mm dia.
Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.
Providing and fixing screw down bib taps of following size.(C) Gun metal screw down bib tap. (i) 15mm dia.
Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.
Providing and fixing brass screw down stop tap.(A) 15mm dia.
Providing and fixing brass screw down stop tap.(C) 25mm dia.
Providing and fixing Gun metal check or non-return fullway wheel valve.(A) 15mm dia.
Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.
Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia.
Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia.
Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia.
Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(ii) 25mm dia.
Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(iii) 32mm dia.
Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.
Providing and fixing ball cock of approved. quality as directed.(B) Abonite (i) 25mm dia.
Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.
Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [F] 50mm.
Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing &Laying & fixing PVC Floor Trap OR multi floor trap of 110 x 110mm dia diameter, with necessary distance piece of 110mm dia pipe and 150x150mm Chillay /Camry/ S.S. Three Pease grating, making necessary SLAB /WALLholes and cutting walls, etc complete. (Supreme/ Astral Makes)
DRAINAGE & SEWERAGE ITEM:- Excavation for pipes upto1.50 MT depth including sorting out and stacking of useful materials and disposing the excavated stuff up to 50 mt lead ( A ) loose or Soft Soil
Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type
Providing and laying in trench Foamcore/ De-rex-HDPE/ ECO-drain PVC pipe as per IS-15328 class SN-4 pipes to the specified invert level and slope and full leak proof joining with rubber ring click ring jointing etc., complete with testing.(Supreme/ Astral Makes) Size:- 160mm
Providing and laying in trench Foamcore/ De-rex-HDPE/ ECO-drain PVC pipe as per IS-15328 class SN-4 pipes to the specified invert level and slope and full leak proof joining with rubber ring click ring jointing etc., complete with testing.(Supreme/ Astral Makes) Size:- 200mm
Providing and laying in trench Foamcore/ De-rex-HDPE/ ECO-drain PVC pipe as per IS-15328 class SN-4 pipes to the specified invert level and slope and full leak proof joining with rubber ring click ring jointing etc., complete with testing.(Supreme/ Astral Makes) Size:- 250mm
Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4- graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x mm and 450mm deep for pipe lines with three or more inlets. .
Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1- cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.
Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1- cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.
Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-corrosive paint etc. complete.
Supplying and fixing C.I. cover 300mm x 300mm without frame for Gulley trap (Standard pattern) te weight of cover to be not less 4.53 Kg.) .
Providing & fixing of the FRP recessed type cover with frame size 600 x 600mm size total weight of cover and frame to be withstand up to 25 ton. with including Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) 25 ton Cap. Recessed type cover( Cover-600 x 600mm ) ( Frame:- 812 x 812mm)
PART-A:- WATER SUPPLY PLUMBING & SANITARY FITTING:- Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour
NSR-MR.ITEMS:-Supplying Installing and fixing wash down wall mounting EWC-P of approved shade, conforming to Pattern 2 of IS: 2556 (Part -II), with SWR Selfit Soil PVC pipe and plug bend as per specifications; glazed vitreous / Cloured European Water Closet with grouting the CI chair in side the floor/wall, rubber gaskets, connecting PVC 110mm dia soil pipe with PVC coupling, nuts, mounting cistern on WC., and solid verity heavy duty plastic seat cover as per IS-2548, of approved make; cutting and making jari work etc. complete. EWC-P : WALL MOUNT EWC WITH CONCEALED FLUSH TANK/ FLUSH PLATE/ SEAT COVER ETC. EWC:_ Code Jaquar-FLS-WHT-5953USFM) ( Tank:- Single Pease concealed tank- Chrome Plate-JCP-CHR-152415, ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing and fixing White glazed vitreous Wash Basin Over -Counter, size 550x460 mm dia., with supporting M.S. or C.I. Brackets, 1 no, 32 mm CP Bottle trap with extension piece to wall flange with rubber adopter for waste connection and waste coupling.; with rack bolt fittings. Over Counter Type Basin , Jaquar Code- FLS-WHT-5603 , with including Jaquar - Cp-waste coupling, bottle trap CP Allied-Chrome Plate- ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing and fixing central hole basin wall mounted concealed mixer with pillar cock,flush plate etc basin wall mounted mixer with required pipes connection etc complete.Wsh Basin Mixer - Wall mounted type- Jaquar- FLR- CHR-5233NK & Plate- ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Single lever Diverter for Concealed Fitting with Built in Non return Valve , for hot and cold water supply controlling with Diverter Handle with provision for both telephone shower and overhead shower complete with bath spout..Single Lever Divertor Jaquar-FLR-CHR-5065NK-/ Over HEad Shower-OHD-CHR-1639/ Shower Arm-SHA-CHR-479L450./ Bath Spout- SPJ-CHR- 54295,with plate etc. comp. ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing in position 15 mm C.P. brass bib cocks of best quality (as approved by the Engineer-in-Charge).FLR-5041N 2 Way Bib Cock With Wall Flange etc. comp. ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Hand Shower (Health Faucet), with 8mm Dia,1Rmt Long pvc Tube and Wall Hook accessories to complete the item. Jaquar- ALD-579 Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) etc. comp. ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing 15mm C.P. brass angle valve with C.P. copper connecting pipe 450 mm long and nuts, washer and brass flange complete, including cutting and making good the wall where required. Jaquar-FLR-5053N Angular Stop Cock With Wall Flange ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of concealed stop cock with wall flange and complete., for the following sizes. 15mm Jaquar-CON-069FTK Exposed Part Kit of Concealed Stop Cock with Operating Lever, Collor Bush & Adjustable Wall Flange (Compatible with ALD-069FT) ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of concealed stop cock with wall flange and complete., for the following sizes. 25mm Jaquar-CON-1081KN Flush Cock with Wall Flange 25mm with Plain Knob type ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing white vitreous china flat back urinal of size 590x375x390mm as per IS-2556 (Part-2 ) with C.I. hangers and 15mm dia. C.P. spreader,15MM cCP angular Stop Cock ,Flexible pipe Connecion, 32mm dia CP bottle trap and pipe to wall with C.P. flange complete including cutting and making good the walls and floors wherever required. Jaquar-URS-WHT-13255 Urinal Without Sensor With Fixing Accessories, Size: 480x300x740 mm ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Pressmatic concealed flush Valve Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Urinal area Flsuh :- PRS-073 Auto closing Concealed Urinal Flush Valve With Wall Flange ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Pressmatic open type anguler cock concealed flush Valve Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Urinal area Flsuh :- PRS-077 Urinal Valve Auto Closing System with Built-in Control Cock & Wall Flange ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Pressmatic open type Bib Tap wall Monted type Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Press Matic Bib cock- Wall Mounted :- PRS-043 Bib Cock Auto Closing System with Built-in Control Cock With Wall Flange ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of Pressmatic open type Bib Tap floor Monted type Auto operation cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. for Press Matic Bib cock- floor Mounted :- PRS-031 Pillar Cock Auto Closing System ( Jaquar, Kohler, Cera or Eq. )
Supplying Installing & fixing of manual operation type Bib Tap wall Monted type cock with wall Flange 15mm with lever knob complete in all respects including cutting and making good the walls etc. Bib cock :- CON-037KN Bib Cock Also available CON-047KN Bib Cock with Wall Flange ( Jaquar, Kohler, Cera or Eq. )
Suppying, installing, testing and commissioing of centrifugal end suction / monoblock pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., base plate, coupling, motor, starter panel, cabling up to panel, earthing,suction, delevery & header pipes & valves etc., complete. (Domestic water pumps : To pump UG tank to OHT Feed Water Tank)( Grundfos, ITT Lowara, or Eq.Make) Capacity : 5 mtr3/hr.2 Nos. main Pumps ( 1 Working + 1 Stand by Set) 15 mtr head. each pump
PUDDLE SLEEVES:- Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,80 mm pipe dia x 600mm length
Providing & Installing of the G.I. heavy duty Puddle Sleeve in the UGT & OHT water tanks , durring the construction of the RCC tanks. The pipe and flazes nut bolt material are as per the IS recommondation must be follow. all works must properly finishing as per site eng. Incharge slab & Beams where ever req. ,50 mm pipe dia x 450mm length
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 38.07 MB
BOQ_4675.xls
BOQ • 13.01 MB
Download all tender documents and submit your bid