SPECIAL REPAIR TO 26 X JCO/OR MD ACCN AT RANJIT LINES, PARTAP LINES AND PR LINES IN MIRAN SAHIB MIL STN UNDER GE JAMMU

Amount

Taking down Chowkats or frames not exc 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down Chowkats or frames exc 1.5 sqm but not exc 4 sqm each each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 5mm thick rendering in CM 1:3 on ceiling surfaces finished even and smooth with out using extra cement complete all as specified and as directed.

M&L Rendering 15mm thick on fair faces of brick/ concrete surfaces built in cm (1:4) , finished even and smooth with WPC without using extra cement complete all as specified and as directed.

M&L for preparation of surface and applying three coat of white wash on newly plaster surface of ceiling complete all as specified and as directed.

M&L for preparation of old plaster or painted surfaces of ceiling and applying two coat of white wash complete all as specified and as directed.

M&L for prepartion of new surface and applying two coat of oil bound distemper over coat of primer over new plaster surface over 1 mm thick putty including 1 coat of primer complete all as specified and as directed.

M&L for complete removal of existing surface & prepartion of old surface and applying two coat of oil bound distemper over a coat of primer including 1 mm thick putty complete all as specified and as directed.

Material and labour for preparation of newly plastered surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Note :-(a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT.(c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed.Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima. Note :-(a) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE. (b) The contractor shall upload along with the documents under cover-I, 'Memorandum of Understanding' (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.

M&L Rendering 20mm thick in CM 1:4 on concrete surface such as chajjas, upward fascias, roof surfaces and similar items including two or more dubbing coat, surface finished even and fair without using extra cement incl mixing of liquid water proofing compound (LWPC shall be measured & will be paid separately) upto height of four storeyed bldg with all necessary, formwork, scaffolding, lifting arrangement for external surface upto 4 storey buildings.) complete all as specified and as directed.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete all as specified and as directed.

S&F 100 mm size stainlless steel hinges medium weight cold rolled stainless steel complete all as specified and as directed..

S&F 50 mm size stainlless steel hinges medium weight cold rolled stainless steel complete all as specified and as directed.

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and as directed.

S&F in repair box type steel windows/Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler /AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar design as per drawing (iv) PCC block for embedding lugs (v) Two coat of synthetic enamel paint (vi) galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

S&F Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and as directed.

S&F Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 125x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side including one coat of primer complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed.Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc)made from co-extruded three layer rigid foam sheet(single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

S&F modular auto concealed soft closed hinges 35mm, 110 degree size fixed to cupboard complete all as specified and as directed.

S & F in repair 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc)made from co-extruded three layer rigid foam sheet(single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

S&F Factory made solid PVC moulded Door frame of size 50x100mm with wood free EPS and 2mm thick moulded PVC sheet alaround supplying and fixing in wall at site as per manufacturer specification complete all as specified and as directed.

S&F Factory made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed.

S&F magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and as directed.

S&F stainless steel handle 100mm fixed to cupboard complete all as spcired complete all as specified and as directed.

Dismantling wrought iron or mild steel work as in cooler stand etc complete all as specified and as directed.

S&F Mild steel works of flat iron, square bar, round bars etc. as in framed works such as grills for pressed box type steel door, framed guard bars, etc and similar work as in cooler stands etc. conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregate as in back filling, bed block for hold fast etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in coping, benching on corner of joints , as in roof kerbs rounded or chamfered on edges etc complete all as specified and as directed.

S&F Aluminium handles D type anodised 150 mm long ISI marked complete all as specified and as directed.

All as per item No 35 here-in-before but 125 mm long complete all as specified and as directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruted section ISI marked complete all as specified and as directed.

All as per item No 37 here-in-before but 200mm long complete all as specified and as directed.

S&F 300 mm long dia 12 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F mild steel enamelled helical door spring 150 mm (ISI Marked)size including roller and roller plate, fixed to wooden/ steel frames by any means as required complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

Hacking out old broken glass (any thickness,size quality or description) from any types of wooden/steel/alum (up to 4th storey) frames or stone concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and as directed.

S&F 3mm thick sheet glass, orinary quality glazing with oil putty in suare not exc 0.5 sqm in each pane complete all as specified and as directed.

All as per item No.43 above but figured glass, Pin head type complete all as specified and as directed.

M&L for preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and as directed.

M & L for Non skid tiles coloured exc 0.06 sqm and n.exc 0.11 sqm , 6-7mm thick of any colour pattern and 1st quality as approved by GE in floor set and fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout, 15mm thick screed bed in CM 1:6 after epoxy grout complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick, edgeless, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and fixed with approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout, 15mm thick screed bed in CM 1:6 after epoxy grout complete all as specified and as directed.

All as per item No 49 here-in-before above but as in vertical surafce ,skirting over and fixed with fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout, 10mm thick CM 1:4 plaster complete all as specified and as directed.

M&L for coloured glazed ceramic tiles glossy finish of size 450x300x 5-6mm thick in dado’s/skirting etc (1st quality). set and fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick polymer modified tile adhesive of appropriate grade as per manufacturer instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout 10mm thick CM 1:4 plaster complete all as specified and as directed.

M&L for 16 to 18 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 20 mm thick screed bed of CM 1:6 incl taking down old complete all as specified and as directed.

Providing edge moulding to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Dismantling Stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20 mm screed bed CM 1:6 including rubbing polishing complete all as specified and as directed.

M&L machine cut kota stone slab flooring 18-20 mm thick as in riser in step, skirting/ dado to match the shade of the slab incl rubbing and polishing over and including 10 mm rendering in CM 1:4 complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

S&F 20 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and directed.

S&F in repair 1000 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position and including dismantling of water tank complete all as specified and as directed.

S&F in repair vitreous china squatting pan 'Orissa pattern, size 580x440 mm white, with integral foot rest and P or S trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all specified in SSR part I complete all as specified and as directed.

S&F in repair vitreous china wash basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackts or erecting stand complete all as specified and as directed.

S&F in repair vitreous china corner wash basin, white, flat back, size 400x380 mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackts or erecting stand complete all as specified and as directed.

S&F in repair PVC valveless, symphonic action type, flushing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair low density PVC connections commercial quality 15mm bore with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F in repair low density PVC waste pipe32 mm bore for flusing cistern complete all as specified and as directed.

S&F in repair 15 mm bore bib taps long nose/long body, cast copper alloy CP fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and as directed.

S&F in repairs Bib taps, fancy type chromium plated ( Short body) with crutch or butterfly handle,screwed down, screwed for iron pipe of 15mm dia bore including necessary fittings complete all as specified and as directed.

S&F in repair 15 mm bore Angle valves, cast copper alloy CP fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair 15 mm bore brass stop cock, cast copper alloy CP with long shank and cup (concealed type), high pressure, with capsgan head handle, weight not less than 450 gms screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair 15mm dia CP pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repair Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hoses complete all as specified and as directed.

S&F in repairs 20 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specified and as directed.

S&F in repairs shower rose brass chromium plated with swivel joint of size 125 mm cast copper alloy CP fancy type with CP neck 9" long made to shape, weight not less than 350 gms complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) , including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete fixed to walls at any height complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete laid in trenches or in floors complete all as specified and as directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete fixed to walls at any height complete all as specified and as directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) bends 110 mm radius complete all as specified and as directed.

S&F 110 mm PVS(SWR) Junction single(T) equal /Unequal complete all as specified and as directed.

S&F PVC (SWR) bends/shoes any radiusof 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and as directed.

All as per item No 85 above Above but 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concerete B1 (1:2:4) complete all as specified and as directed.

S& F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75 mm bore pipe complete all as specified and as directed.

S& F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and as directed.

S&F 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (min wt-210 gms) complete all as specified and as directed.

S&F in repair brass CP towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

S&F in repair 125 mm dia steel grating with or without hole complete all as specified and as directed.

S&F in repair MS peg set of six power coated as approved by GE complete all as specified and as directed.

S&F in repair drapery curtain rod of metalic 20 mm dia covered with PVC coating including MS bracket, end ball, rounded block (coated with brown/cherry/golden colour) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washers and waste coupling, waste pipe, incl bedding in cement mortar on wall incl fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm, bowl size 410mm x 330mm x 160 mm complete all as specified and as directed.

Demolition of cinder concrete of any description and in any position and removing the rubbish from work site complete all as specified and as directed.

M & L for Cleaning sunken surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. M & L for providing water proofing treatment to sunken floors all as given below :- (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty CICO POXY LC or epoxy mortar CICO POXY 2125. (c) Cleaning the concrete surface by brushing & watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of TAPECRETE P-151 and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of TAPECRETE brush topping 1.5mm thick consisting of one part of TAPECRETE P-151, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in CM 1:4 mixed with CICO super @ 100ml per 50 Kg cement on treated surface. (f) M & L cement concrete type E-2(1:5:10) as in filling of sunken floor. Note : Ponding test should be performed for 48 hours as per direction of engg. in charge.

M&L for galvanized pipes spout 40mm dia light grade ,fixed to walls complete all as specified and as directed.

M & L for Complete removal of existing roof treatment or roof tile or plaster and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified. M&L for highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties: 1.UV resistant ,prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying OEM prescribed compatible primer over the prepared surface for adhesion and bridging cracks. Coverage: 0.2kg/m2(with 50% dilution of water Reinforcement: Geotextile 40 gsm Second coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption: 0.5 kg/m2. Third coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption : 0.8 kg/m2. System buildup-1.5kg/sqm with geotextile of 40gsm For accessible roof, tiles with screed/ adhesive may be fixed thereafter.

Material and labour for plastering 10 mm thick in cement mortar (1:3) using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B 0(12.5mm graded crushed stone aggregate) , floor surface complete all as specified and as directed.

M&L for SRI tile 300mm x 300mm x 10 mm thick set, jointed and pointed in roof floor/terraces over and including 15mm thick screed bed in CM 1:4 with chemical based adhesive as per manufacturer instruction complete all as specified and as directed.

Supply only liquid water proofing compound. complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

All as per item No.107 above but except bricks complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in Cement Mortar 1:4 complete all as specified and as directed.

Excavation in trenches, not exc 1.5m wide not exc 1.5m in depth: for foundation, etc, or for shafts , wells cesspits, manholes, pier holes, etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out, in hard/dense soil complete all as specified and as directed.

Demoliton/breaking of drain pipes (salt glazed ware,AC or reinforced concrete) set in cement mortar and taking out off trenches and removing the debris from the site all as spd of 150mm/200 mm dia pipe inclding demoilition of cement concrete haunching etc complete all as specified and as directed.

M&L concrete bed to 150 mm bore pipe in D2 1:4:8 (40mm graded aggregate) inclduding haunching against the sides of pipe complete all as specified and as directed.

S & F and laying 150 mm thick reinforced concrete pipes class NP-2 laid and jointed complete with collers as in trenches and complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removal of surplus excavated soil to a distance exc 250 m & not exc 500m and deposited where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

M&L providing precast cement concrete in cover slab (for manhole) type B1 1:2:4 (20mm graded aggregate) set in Cement mortar 1:4 complete all as specified and as directed.

M&L MS TMT bars 10 mm dia and over cut to length, bend to shape etc complete binding with and including mild steel annealed wire not less than 0.09 mm dia conforming TMT bars complete all as specified and as directed.

Taking out of solid/semi solid sludge from existing main holes of any size and any depth and burying the entire sludge/sludge water in to excavated pit of adequate size including excavation and covering with earth or disposing off into covered vehicles outside the periphery of defence land to a distance exceeding 1 KM including taking off RCC/iron main holes covers and refixing the same after clearing complete all as specified and as directed.

M&L for Cement concrete type C-2 1:3:6 ( Using 40 mm graded stone aggregate) as in surface channels complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material and labour for Reinforced cement concrete (nominal mix) 1:2:4 Type B-1(using 20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for Formwork to flat soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished complete all as specified and as directed.

Material and labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide complete all as specified and as directed.

Supply and fixing in repair soap dish steel chromium plated 100 mm size complete all as specified and as directed.

S&F in repair plate rack stainless steel of size 600x900 mm fixed with washer and plugs complete all as specified and as directed.

M&L for preparing old surface of steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for pressed Steel wire gauged skelton door Box type (primer coated) ERW hollow section 1.0 mm thick, size for vertical (styles), top rail, middle rail and bottom rail (100 mm x 35 mm) single rebated comprises wire gauged skelton shutter with four Nos in each panels of FI section size 12x3mm complete screwed to frame for holding wire mesh complete all as specified and as directed.

S&F in Mild steel barrel tower bolts of 150mm long stove enamelled black with bright bolts and fixed complete all as specified and as directed.

S&F in 150mm long Mild steel pressed handles oval type, stove enmelled black, complete all as specified and as directed.

S & F in repair 15mm bore for CP wall mixer for mixing hot or cold water screwed down iron pipes complete all as specified and as directed.

M& L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonary apron using chemical emulsion @2.25 litre per linear metre including drilling and plugging hole etc in apron etc. complete all as specified and as directed.

M& L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

M& L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

S&F in repair 25 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Demolition of concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for providing 75 mm thick plain cement concrete 1:4:8 mix, type D-2 (Using 40mm graded stone aggregate) as sub-base floor complete all as specified and as directed.

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board pvc/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down Ceiling fan, sealing cable end, dismantling blades and removing fan and blades to store and Hanging to same location to ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose after completion of point wiring complete all as specified and as directed.

Taking down Exhaust fan from wall and sealing cable end, keeping it in store and fixing it to same location and connecting up including provision of cable from ceiling rose after completion of point wiring complete all as specified and as directed.

Taking down geyser and keeping it in store and fixing it to same location and connecting up with cable after completion of point wiring complete all as specified and as directed.

M&L in replacement for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , multistranded , copper conductor FRLS, drawn through the New rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length incl taking down old wiring. Note : 1) Wiring shall be done in proper colour coding. 2) Rates are inclusive of cutting / chasses withsuitable PCC works and making good to disturbed surfaces.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid conduit with modular CI / pressed steel sunken / terminal boxes of required size including Modular cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note :1) Wiring shall be done in proper colour coding. 2) Rates are inclusive of cutting / chasses withsuitable PCC works and making good to disturbed surfaces.

Material and labour for point wiring for one light point controlled by Two 2 way switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid conduit and with modular CI / pressed steel sunken terminal boxes of required size for mounting modular cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note :1) Wiring shall be done in proper colour coding. 2) Rates are inclusive of cutting / chasses with suitable PCC works and making good to disturbed surfaces.

All as per item No 143 above but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed.

All as per item No 143 above but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed.

All as per item No 143 above but for One bell point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed.

All as per item No 143 above but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 sqmm copper conductor multistrand cable pvc insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 sqmm as earth wire FRLS pvc insulated in green color complete all as specified and as directed.

S&F in Modular Socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

S&F in Modular switch 1 module 6A,1 module , 240 volts ISI marked complete all as specified and as directed.

Supply and fixing of Modular Switch 2 way 6A,1 Module complete all as specified and as directed.

S&F in Modular bell push switch 6A, 1 module , 240 volts ISI marked complete all as specified and as directed.

S&F in ceiling rose, 2/3 Pin/PVC/polycarbonate isolated body ISI marked complete all as specified and as directed.

S&F in Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and as directed.

(S&F in Modular Socket 6A/16A - 6 pin combined 2 module, , 240 volts ISI marked complete all as specified and as directed.

S&F in Calling bell Ding Dong AC 230 Volts, single pole ISI marked complete all as specified and as directed.

M& L in for Modular Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

M& L in Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

S & F in LED light fitting 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing and replacement of V TPN DB double door,IK 09,IP43-Metal door, 4 way, made of CRCA sheet steel ,RAL 9003,powder coated with bus bar, neutral link, earth bar withprovision for MCCB 3 Pole as incomer and SP MCBs as Outgoings, including taking down old one complete all as specified and as directed.

M&L for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed.

Supply and fixing in replacement MCB SPN 40 to 63 Amp rating 240V, 10KA 'B' curve type, in the MCB DB complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement for 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB DB complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement for 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 Amp, in the MCB DB complete with connection, testing and commissioning complete all as specified and as directed.

M&L for Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on complete all as specified and as directed.

Supply & Fixing in repairs MCCB of 100 Amps,3 pole ,with Thermal -Magnetic Release , type with breaking capacity Icu at 415 volts AC,50Hz , 16 kA ,including connection and testing complete all as specified and as directed.

Supply and fixing in replacement Modular type Fan step regulator, 120 W - 2 module 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver,& 32 mm dia GI Pipe Medium Grade Bracket, Mounting 02 nos Clamps nut & Bolt/Anchor Bolt with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Disconnecting and taking out defective Open cable any size and any type from trenches, roof, pole, pipe, floor, wall from Lt Pole to V TPN DB etc complete all as specified and as directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 25 Sqmm 4 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and as directed.

Excavating in trenches n.exc 1.5 mtrs wide and n.exc 1.5 mtr in depth for foundation of poles, taking out/laying of cables, poles etc and getting out in soft/loose soil complete all as specified and as directed.

M&L Sand filling in cushing bed of cable and consolidation complete all as specified and as directed.

Supply and laying comman burnt clay building sub class `B' bricks, laid over sand Cushioning laid at right angle along with cable, complete all as specified and as directed.

Returning filling in excavated soil in trenches, watering and well ramming in layers n exc 25cm complete all as specified and as directed.

Removing of excavated any type of soil to distance n exc 50m complete all as specified and as directed.

S&L GI tubing tight graded 40 mm dia incl all accessories for encasing cables for mechanical protection, laid under plinth/floors/path culverts with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works complete all as specified and as directed.

M & L for cutting the existing concrete/bituminious road surface width n.exe 30 cm and making good the surface with 100 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate finished even and fair complete over 100mm thick PCC 1:4:8 type D2 using 40mm stone sggregate over consolidated/rammed earth surface complete all as specified and as directed.

Supply and fixing in replacement LED light fitting mirror type with high ouput diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

SHARMA CONSTRUCTION COMPANY (BID ID -3501789)

M/s Sunny Gupta (BID ID -3502892)

M/S Shesh Paul Gupta (BID ID -3502833)

NARESH KUMAR AND COMPANY (BID ID -3508665)

AJAY GANDOTRA (BID ID -3508534)

M/s Koul & Sons (BID ID -3508390)