GE/863/EWS-T-48/2019-20

Amount

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed by Engr-in-Charge.

S & F of 6 mm thick (5 Nos of ply) plywood BWR grade, type – BB, fixed with nails to timber frame as in ceiling, flat or sloping and similar locationcomplete all as specified and directed by Engr-in-Charge.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in Unframed work or Framed workcomplete all as specified and directed by Engr-in-Charge.

S & F of 2nd class hard wood (SAL) in scantling, clean sawn in any position and any description as in framed or unframed work complete all as specified and directed by Engr-in-Charge.

M&L clean sawn second class hard wood for scantling as in framed or unframed work but except timber complete all as specified by Engr-in-Charge.

S & F of 2nd class soft wood (CHIR) plain fillets, bull nosed, splayed, chamfered or rounded on one face or edge, clean sawn, secured with nails sectional area exc. 3 sqcm but not exc. 6 sqcm complete all as specified and directed by Engr-in-Charge.

Demolition of ashlar facing, dressed stonework, pre-cast concrete articles and pre-cast concrete block walling including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed by Engr-in-Charge.

M & L for block masonry with solid pre-cast cement concrete blocks made out of cement concrete 1: 3: 6 type C-1, using 20 mm graded stone aggregate, exc. 10 cm in width and setting in cement mortar 1 : 6 complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below and above ground level) complete all as specified and directed by Engr-in-Charge.

M&L for 50mm thick cement concrete type C2, 1:3:6 (using 40mm graded stone agg) as in plinth protection finishing fair and even without using extra cement complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (reinforced) as in Roofs, floors (other than ground floors) beams, stairs case, landing, chajjas and similar suspended work complete all as specified and directed by Engr-in-Charge.

M & L for providing 25 mm thick cement concrete 1:2:4 type B0 Nominal Mix (using 12.50 mm thick graded stone aggregate) as in sub base of floor, etc and finishing surfaces of concrete even and rough to receive the topping layer complete all as specified and directed by Engr-in-Charge.

M & L for Non skid ceramic coloured tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exc. 0.38sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15 mm thick screed bed or bedding layer of mortar 15 mm thick for laying floor finishedcomplete all as specified and directed by Engr-in-Charge.

M & L for machine cut kota stone slab flooring 20 - 25 mm thick laid over & including 20 mm thick screed bed laid in CM 1:4 and jointed with grey cement slurry mixed with pipgment to match the shade of the slab including rubbing and beewax polishingcomplete all as specified and directed by Engr-in-Charge.

M & L for Glazed ceramic coloured tiles of size 300 mm X 200 mm X 7 mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles laid over & including 10 mm thick on concrete surfce as in backing coat for laying wall tiles in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc.complete all as specified and directed by Engr-in-Charge.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed by Engr-in-Charge.

S & F of rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, running rails and guides for sliding doors fixed with angle cleat and other connecting plates confirming to Fe – 410 complete all as specified and directed by Engr-in-Charge.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engr-in-Charge.

M/L PCC 1:3:6, type C-0 using 12.5 mm graded stone agg as in coping to walls/steps including necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L for RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Lintel beams roof beam all as specified and directed by Engr-in-Charge.

M&L for RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chajjas and RCC slab complete all as specified and directed by Engr-in-Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed by Engr-in-Charge.

Supply & fixing 0.63mm thick galvanised corrugated MS sheeting with two corrugation side lap, fixed with J/L hook in roof of class 3 complete all as specified and directed by Engr-in-charge.

Fixing only 0.63mm thick galvanised corrugated MS sheeting with two corrugation side lap, fixed with J/L hook in roof of class 3 complete all as specified and directed by Engr-in-charge.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed by Engr-in-Charge.

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concretecomplete all as specified and directed by Engr-in-Charge.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or secure complete all as specified and directed by Engr-in-Charge.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but not exceeding 4.00 sqm each but with shutter (without taking off shutter from the frame) and removing to store complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames not exc 1.5 sqm each but with shutter (without taking off shutter from the frame) and removing complete all as specified and directed by Engr-in-charge.

S&F for 2nd class hard wood plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed. complete all as specified and directed by Engr-in-Charge.

S&F factory made 2nd class hard wood rail and style Plain, framed, panelled shutters 40 mm thick ( two panels), with lock rail ad panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and stile as per IS 1003 (Part I ), kiln seasoned and chemically pressure treated all as specified and directed by Engr-in-Charge.

S&F lInd class hard wood 35mm thick glazed and Skelton shutters, open rebated and preparing to receive glass, gauze, etc (with sash bar edges of framing plain chamfered or rounded fitted cut & mitred beads for securing wire cloth. Size of members of shutters as specified in SSR Part -I section 8 , clause 8.23(a) and fitted to chowkats complete all as specified and directed by Engr-in-charge.

S & F of 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter as specified in clause No. 8.24 (b) of MES schedule part – I (Specifications - 2009) complete all as specified and directed by Engr-in-Charge.

S&F for IInd Class hard wood of Small fittings such as brackets of any type, latch and hing blocks, shaped door & window stops & the like, including all necessary labours; articles n exc 200 cu.cm each complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:2:4 type B1 (20 mm graded aggregate) as in bed plates to fix hold fast etc complete all as specified and directed by Engr-in-Charge.

S & F of flat iron bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gate, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fast, wall ties, hooks for hanging fans and other similar small steel article conforming to Fe – 290 Gde E -- 165 complete all as specified and directed by Engr-in-Charge.

M & L for preparation of surface of wood and wood based materials, steel or iron work, new or old of any description or girth not otherwise described, and treated with tar or coal tar black paint as in ends of posts, back of chowkhats etc. area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm each complete all as specified and directed by Engr-in-Charge.

M & L for preparation of surface of wood and wood based materials, steel or iron work, new or old of any description or girth not otherwise described, and treated with tar or coal tar black paint as in small articles such as stop, covers, gully gratings, holdfasts, ende of posts, back of chowkats, etc. area tarred not exc. 0.10 Sqm each complete all as specified and directed by Engr-in-Charge.

Supply & fixing MS barrel tower bolt of 150mm long stove enamelled black with bright bolt complete all as specified and directed by Engr-in-charge.

S & F of 125 mm long (Length of bolt) mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and directed by Engr-in-Charge.

S & F of 250 mm long (Length of bolt) mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engr-in-Charge.

S&F 125mm long MS butt hinges medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F 75mm long MS butt hinges medium weight cold rolled. complete all as specified and directed by Engr-in-Charge.

Supply & fixing MS pressed handle oval type stove enamelled black of 125mm long fixed with screw to shutter complete all as specified and directed by Engr-in-charge.

Supply & fixing MS pressed handle oval type stove enamelled black of 100mm long fixed with screw to shutter complete all as specified and directed by Engr-in-charge.

Supply & fixing 300 mm ,Mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples. and directed by Engr-in-charge.

S & F of 4 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

M& L for two coats of synthetic enamelled paint over a coat of pink primer on newly wooden surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M& L for one coat of synthetic enamelled paint over a coat on old steel surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M& L for two coat of synthetic enamelled paint over a coat of red oxide on new steel surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick on fair faces of PCC block walling in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set, jointed and pointed in neat cement slurry laid over & including 20mm thick screed bed in cement mortar 1:6 as in floors with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick on fair faces of PCC block walling in CM 1:6 incl for even and smooth finishing without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L for two coats of cement base paint including preparation of new plastered surfaces on walls complete all as specified and directed by Engr-in-Charge.

Demolition of stone walling/boulder masonary , laid dry complete all as specified and directed by Engr-in-Charge.

M/L precast PCC 1:3:6 type C1 using 20mm graded stone agg as in bond stone set in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. Note :- The quantiry of bond stone used in the wall shall be deducted from stone masonry .

M&L for two coat of oil bound distempering over priming including preparation of new wall surface surface complete all as specified and directed by Engr-in-Charge.

M & L for walling of random rubble stone masonry, un-coursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M & L for walling of random rubble stone masonry (EXCEPT STONE), un-coursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. Note: - old stone obtained from demolition shall be used under this item.

M & L for Raised pointing to random or polygonal rubble, uncoursed or buought upto course in cement mortar 1:3 to walls complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith compete fittings such as switches ,ceiling rose, pendent holder, sketch fitting & regulator etc. including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down unserviceable service cable any size removing from the pole to main DBs complete all as specified and directed by Engineer-in-Charge.

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed by Engineer-in-Charge

M&L for point wiring using approved colour coding as per IS with FRLSH PVC insulated 1.5 Sqmm multistranded, 1100 volt grade copper conductor cable, unsheathed type alongwith FRLSH PVC insulated 1.50 sqmm multistranded copper conductor cable for continuous earthing in & incl PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling terminated into PVC gang box for mounting switches, sockets etc. all as specified for one light point/ fan /Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 67 here-in-before but controlled with one socket outlet 5 AMP on the independent board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 67 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the same board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 67 here-in-before but controlled with one socket outlet 15 Amp, independent board with cable 2.50 Sqmm including provision of 1.50 Sqmm single core multistranded PVC insulated copper conductor as earth conducting conductor complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of socket outlet 3 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of socket outlet 6 pin 5 / 15 Amp, 2-in-one 230 volt flush type complete all as specified and directed by Engineer -in-Charge.

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED 20W tube light fitting batten extruted aluminium housing and robust construction 20 W system lumen with all accessories all as specified and directed by Engg-in-Charge. Make: Bajaj Cat No. BLRB-DB 118 or equivalent of Wipro and CG/Philips

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings. Make : Anchor/leader/havells

Supply and fixing LED lamp 12 W system lumen (NOM) 600 with all accessories all as specified and directed by Engg-in-Charge. Make:Cromptom part No-LED 12DFCDL-PRO-BO or equivalent of Bajaj/Philips/wibro

Supply & Fixing energy saving new generation 10 W LED IP65 bulk head luminaire with opal diffuser powered with high power LED as light source complete all as specified and directed. Make : Havells Cat no. LHEOAOP7UZ6W010 or equivalent in crompton / Philips / Wipro /Halonix.

M&L for building light fitting 20 Watt LED type, energy saving & environmental friendly long life Versatile pressure die-cast aluminium, IP65 roadway luminaire with high power LEDs as light source and electronic driver incl provn of PVC insulated unsheathed multistranded copper conductor two core cable,GI pipe 1.2mtr long, a pair of clamp, bolts, nuts, washers including dismantling existing old light fittings . complete all as specified and directed by Engineer-in-Charge. Make Crompton Cat No LST-20-CDL or equivalent of Wipro/Philips/Bajaj

Dismantling and Supply,fixing, Testing water heater storage type with multifunctional safety valve, electric operated 230 V, Single Phase complete including one no of heating element, automatic, thermal cut out, fusible plug, anti vacum sys, built in presser release valve,thermostat, rust proof powder coated body, indicator lamps and all safety advices as per E-in-C's Branch technical instructions and of capacity 25 liters including provn of grouting bolts in walls including piller cock , pvc connection ect and making good disturbed surfaces. Make : CG/Racold/Havells/Bajaj/indo and all as specified and directed by Engineer-in-charge .

S&F for exhaust AC, Single Phase 300mm sweep, with louvre including dismantling existing old u/s exhaust fan complete all as per specified and directed by Engineer-in-Charge.

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt complete all as specified and directed by Engineer-in-Charge

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 4 way 240 volt with copper bus bar, neutral and earth link complete all as specified and directed by Engineer-in-Charge

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt with copper bus bar, neutral and earth link complete all as specified and directed by Engineer-in-Charge

S&F SPN 40 Amp rupturing cap 10 KA 'C' series all as specified and directed.

S&F MCB SP 6 Amp to 32 Amp, rupturing cap 10 KA 'C' series all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of size 16 Sqmm complete

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below the ground level with top edge of the earth plate not less than 1.50 mtr below ground level connected to the galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolts, check nuts and washer of galvanized iron including PCC pit in PCC 1:2:4 type B-1 precast RCC cover slab using reinforcement with XPM weighing not less than 1.87 kg/sqm with suitable handle maded of 12mm round bar, including necessary ecavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for atering with one end fixed with sat iron funnel and wire mesh 15mm dia bore light grade galvanized steel tubing upto 5m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate no. 3 of SSR Part-I and testing on completion.

Net Contract Sum will be after deducting Sch Of Credit of Rs 38980.00

M/S SHIV NATH ENTERPRISES