GE(S)BTD 01 OF 2025-26 REPAIR AND RENOVATION OF GROUP V AT CSD DEPOT AND PROVISION OF BOUNDARY WALL AT THE BACK SIDE OF CHETAK OFFRS INSTITUTE OF AGE BR II AND AGE EM IV UNDER GE(S) BATHINDA AT BATHINDA MILITARY STATION

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridge sheet complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and as directed.

S&F factory made stainless steel turbo air ventilator 600mm dia fixed with galvalume sheet complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

Anodised aluminium snap grid (Size of grid 605 x 605mm) frame work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

S&F 4 mm thick Non asbestos fibre cement building boards as in false ceiling fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each and removal from site complete all as specified and as directed.

M& L for Pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) complete all as specified and directed.

Pressed steel frames of size 75 X 60 mm for Cupboard frames with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) complete all as specified and directed.

PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in back of pressed steel door frame/chowkhat and fixing of bed block of hold fast etc complete all as specified and as directed.

S&F 35 mm thick Flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Pressed steel shutter for cupboard with sheet thickness not less than 1.2 mm made to shape as shown on drawing with and including locking arrangement, handles and one shop coat painting complete all as specified and directed.

S&F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F Powder coated aluminium window and ventilator shutters( sash and wire gauge shutter), top hung/side hung type, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, powder coated aluminium fittings such as hinge type B-21 100mm long (2 Nos), suitable handle (1 No), tower bolt 100mm (2 Nos), stay (1 No ) for side hung shtter and 2 spring latches for top hung shutters each, complete all as specified and as directed. and shown in drawing.

S & F 4 mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section, 150 mm long (ISI marked) complete all as specified and as directed .

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 150 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc. complete all as specified and directed.

S&F 5mm thick Anodised aluminium grill with size of opening 50 x 50 mm(anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick cement screed bed in CM 1: 6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick backing coatin CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Carefully chipping, removing existing loose/ damaged concrete with plaster from Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items by low impact high frequency hammer/ chipper without damaging the existing sound concrete and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade, making the edges straight and even and cleaning it by wire brush and then by air blower complete all as specified and as directed.

Cleaning all existing reinforcement bars in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items with wire brush/rotary wire brush to make entire circumference surface of bars free from rust scales, loose material, dirt etc., complete and applying alkaline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, complete as per manufacturer’s instructions, complete all as specified and as directed. Note :- Mode of measurement : per sqm of breaking area of concrete only.

Providing and application of Zinc rich epoxy anti-corrosive protective coating for reinforcement bars as corrosion protection system in 2 coats to the entire circumference surface of bars (consumption Qty as per manufacturer's instructions but min 0.4 kg/Sqm approx) in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items complete all as specified and directed by Engr-in-charge. The product should confirm carbonation resistance of 2 mm and bond strength > 1N/sqmm according to ASTM C 882-78 complete all as specified and as directed. Note :- Mode of measurement: per sqm of application area of concrete.

Apply SBR based bonding agent to the entire concrete surface prior to building up of concrete with Polymer modified mortar or any other treatment , including cleaning the surface to remove dirt, dust or any other impurities on the surface, etc. complete in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items complete all as specified and as directed.

Rebuilding the section of structural damaged RCC/PCC elements of Roof, Ceiling, Chajja, Fascia, Fins, Drops repair to spalling concrete to its original size and shape in layers of 10 mm average thickness in 1st layer by providing and applying with pre-batched, one component fiber based repair mortar having compressive strength >= 50 N/sqmm (28 days) according to ASTM C 109; flexural strength >= 5N/ sqmm (7 days) according to ASTM C 293-79 complete all as specified and as directed.

All as per Srl item No 30 here-in-above but for each additional 10mm uniform thickness for subsequent layers.

Cleaning of old Roof / wall concrete surfaces & applied a coat of cold bituminous primer over cleaned surface @ 0.40 Kg/Sqm followed by APP modified five layer ploymeric membrane 3mm thick, minimum wt 3.50 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) manufactured by M/S STP Ltd/IWL India Ltd or its equivalent, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required complete all as specified and directed.

Taking down old unserviceable rolling shutter of any size upto 8 Sqm area including hood cover complete with all aaccessories and making good disturbed surfaces with CM 1:4 complete all as specified and as directed.

S&F Steel rolling shutters, with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type complete all as specified and as directed.

Taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish from the premises to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement complete all as specified and as directed.

M&L for prepration of new plastered surface of wall and applying three coat of White Wash complete all as specified and directed.

M&L for complete removal of existing treatment on old plastered surface of wall and applying two coat of White Wash complete all as specified and directed.

M&L for prepration of new plastered surface of wall and applying Two coat of Cement base paint over a coat of white wash of reqd tint / colour complete all as specified and directed

M&L for complete removal of existing treatment on old plastered surface of wall and applying Two coat of Cement base paint of reqd tint / colour complete all as specified and directed

M&L Brick work built in cement and sand mortar 1:6 with sub class 'B' old size bricks straight or curved on plan exceeding 6m means radius complete all as specified and as directed.

Demolition of RCC of any description such as chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed. (Note: Reinforcement cut as required to facilitate demolition)

M&L for prepration of new plastered surface and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth including two coat of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for complete removal of existing treatment on old plastered surface and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth including two coat of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

Material & Labour for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

Material & Labour for complete removal of existing treatment on old plastered surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

M&L prepration of new wooden Surfaces of any description, over 10cm in width or girth,not otherwise described an applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L prepration of old steel Surfaces of any description, over 10cm in width or girth,not otherwise described an applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 using 40mm graded aggregare 75mm thick as in plinth protection complete all as specified and directed.

M&L Sand filling 25mm thick under floors or in foundation complete all as specified and directed.

M&L 60mm thick inter locking PCC block of M-35 as per IS 15658-2006 approved design made out of grey cement and pigment laid complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F Expanded metal Exc 4 kg per sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and as directed.

M&L Preparation of new steel surfaces of any description over 10cm width or girth and applying a coat of red oxide zinc chrome primer and two coats of synthetic enamel paint including preparation of surface complete all as specified and directed.

Excavating in trenches, in soft/ loose soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L Cement concrete Type C2, 1:3:6 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete sur?faces finished even and smooth (without using extra cement) complete all as specified and as directed.

Ditto as per srl item No. 63 here in before but other than fair faces of brick work complete all as specified and as directed.

M&L Providing, cement concrete Type B2 (1:2:4) using 20 mm graded stone aggregate as in Copings, including necessary formwork complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour by using paint brush complete all as specified and as directed.

Taking down carefully copper/aluminum point wiring (Light/ fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc, removing materials to store for keeping in for taking credit and making good the disturbed surfaces / walls/ floors etc,. complete all as specified and as directed.

M&L for flameproof point wiring for one light point/exhaust fan point controlled by one MCB circuit or one ceiling fan point controlled by one flameproof fan regulator and one MCB circuit with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FRLS and including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLS connected to common earth dolly drawn in and including surface run ERW stove enameled black rigid steel conduit 20 mm dia heavy duty ISI marked, accessories such as flame proof joint, bends, corners, tees, unions, reducers, nipples etc. all in LM6, screws, clips, clamps etc. complete complete all as specified and directed:- Note :1. FLP Junction boxes,Flexible conduit & inspection Elbow shall be measured and paid seperately under respective Item of schedule.

All as per above (Item no 68) but for each additional light point on the same MCB circuit.

Supply and fix Flameproof junction box LM6 protection, 4 way including accessories suitable for 20mm ERW pipe in wiring complete all as specified and as directed.

Supply and fix Flameproof junction box LM6 protection, 3 way including accessories suitable for 20mm ERW pipe in wiring complete all as specified and as directed.

Supply and fix Flameproof flexible metalic hose conduit pipe 20mm x 300mm long complete all as specified and as directed.

Supply and fix Flameproof inspection elbow protection suitable for fixing with ERW conduit 20mm dia in wiring complete all as specified and as directed.

Supply and fix CMRI certified flame proof distribution board of the die cast aluminium alloy(LM-6) gas group IIA,IIB & IIC, SPN 8 way, 230volt grade, suitable for fixing & including MCB SPN 32 Amps, 10kA-01 Nos(incoming), and SP 6 Amps 10kA-06 Nos (outgoing) all pre-wired and conforming to IS-2148/2004 & IS 13346/2004 complete all as specified and directed. Distribution box to be fixed flush to wall suraface complete all as specified and as directed.

Supply and fix CMRI certified flameproof 40 Watt LED bulkhead/ wellglass luminaire recommended for Gas/vapor group of IIA & IIB and Zone 1&2, die cas aluminium housing with heat resistant toughened glass/dome glass/external reflector, IP66 protection, wall/surface mounted precoated electronic type luminaires with inbuilt electronic driver, connector block, etc complete with accessories internally pre-wired and including connecting the fitting with twin core twisted flexible copper conductor cable and connector block complete all as specified and directed

Supply and fix CMRI certified flameproof 2x16 Watt LED light fitting recommended for Gas/vapor group of IIA & IIB and Zone 1&2, with die cast aluminium housing with heat resistant toughened glass with LED tubelight fixtures etc, wall/surface mounted, electronic type luminaires with inbuilt electronic driver, connector block, etc complete with accessories internally pre-wired and including connecting the fitting with three core twisted flexible copper conductor cable and connector block complete all as specified and directed

M&L for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia (upto the cross arms) by means of GI bolts/nuts/washers, protected by 15 mm bore GI medium grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, RCC cover & frame, PCC (1:3:6) type C-2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of MES Schedule Part – I.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4.0mm dia galvanised iron or steel wire all as specified.

S&F Heavy duty flameproof/weatherproof exhaust fan, of 18" sweep, 230 volt, copper winding, complete with one complete blades set, louvers and shutter and mounted in suitable opening arrangement in wall and in & including connection cable including grouting of bolts, nuts etc complete all as specified and directed

S&F flameproof/weatherproof ceiling fan 48" sweep complete with one fan regulator, high performance with one complete set of blades, 100% copper motor, with set of canopy, down rod, shackle assembly, and accessories complete all as specified and directed

M & L for Point wiring with multi-stranded copper conductor, single core, PVC insulated and unsheathed cable, including PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, GI terminal boxes, modular frame & cover plate (suitable for modular switch/sockets) comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in 25mm medium duty concealed conduit complete all as specified and as directed.

One Socket outlet three pin, 6 Amp, on the same board, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, complete all as specified and as directed.

One Socket outlet three pin, 6 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in 25mm medium duty concealed conduit complete all as specified and as directed.

One socket outlet three pin, 5/15 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in 25mm medium duty concealed conduit complete all as specified and as directed.

Note for serial item No 81.00 to 85: 1. Switch(es), socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. 2. GI boxes shall be fixed flush in position with cement mortar (1:4) complete all as directed.

S&F Switch modular type single pole, one way, 6 Amp, one module, complete all as specified and as directed.

S&F Switch modular type single pole one way, 16 Amp, one module, complete all as specified and as directed.

S&F Socket outlet modular type, multipurpose, 3 pin, single pole one way, 6 Amp, two module, shutter type complete all as specified and as directed.

S&F Socket outlet modular type multipurpose 3 pin, 2 in 1 single pole one way 6/16 Amp, two module, shutter type complete all as specified and as directed.

S&F Fan regulator, modular type, 5 step, high speed, two module complete all as specified and as directed.

S&F Ceiling rose, 3 terminal PVC/polycarbonate, suitable for 230 V, AC, 50 Hz supply complete all as specified and as directed.

S&F LED panel light fitting, recessed mounted, square shaped of size 595x595x65 sqmm, 36(±10%)watts efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor, module and inbuilt driver complete including making connection complete all as specified and directed.

S&F LED downlighter/spot light fitting, recessed mounted, round shaped of ceiling cut outφ160mm, 12watts efficacy not less than 90 lumen/watt, 6500K extruded Aluminium/polycarbonate, PC diffusor, module and inbuilt driver complete including making connection complete all as specified and directed.

S&F in replacement sheet metal encloser double door 4 way TPN 415V ISI marked complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module complete all as specified and directed

S&F in repair MCB 6-32 Amp 240V SP 10 KA ‘B’ series complete all as specified

S&F in repair MCB 40 Amp 415V TPN 10 KA ‘B’ series complete all as specified

Taking down carefully existing ceiling fans/exhaust fan any sweep, deposite safely to store yard complete all as specified and as directed.

Hanging only ceiling fan/exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed.

S&F in replacement sub main two runs of single core PVC copper conductor unsheathed wire multi stranded 6 sqmm along with one run of earth wire 6.0 sqmm copper conductor single core wire connected by common earth in including surface run ERW stove enameled black rigid steel conduit 20 mm dia heavy duty ISI marked including accessories such as flame proof joint, bends, corners, tees, unions, reducers, nipples etc. all in LM6, screws, clips, clamps etc. complete all as specified and as directed. (Note :- two lengths of 6.0 sqmm cable and one length of 6.0 sqmm earth cable along with rigid steel conduit will be measured as one running length)

RAKESH KUMAR GARG & CO. (BID ID -3302023)

B D BATRA AND SONS (BID ID -3302331)

M/s Balvinder Singh Engineer and Contractors (BID ID -3302341)

RAMA AUTOS (BID ID -3302344)

SB Builders (BID ID -3302287)

FATEH ENTERPRISES (BID ID -3301629)

Easyways Enterprises (BID ID -3302174)

BALAJI CONSTRUCTIONS (BID ID -3301825)