DEVELOPMENT OF INFRASTRUCTURE WORKS AT FINTECH CITY,NANDAMBAKKAM VILLAGE,ALANDUR TALUK, CHENNAI DISTRICT

Amount

PART-1 - EARTH WORKS AND ROAD WORKS :

Clearing Light jungle including uprooting of trunk vegetation,grass,brush wood,trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the Project Officer with an initial lead of 10 mts and initial lift of 2 mts. and including necessary backfilling in layers of not more than 15 cm thick well rammed, watered and consolidated, clearing and levelling the site, etc., complete complying with standard specification.

Earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the Project Officer in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Carting away surplus excavated earth beyond initial lead of 10 m to approved designated locations within site including loading, unloading and stacking as directed. Lead shall be various kilometers from source location to stock yard.

Within 1 Km

Within 3 Km

Providing Pre-constructional Antitermite treatment including cost of chemical labour as per standard specification for preparing the area for treatment by spraying chemicals and other incidental charges etc., complete the rates should be for curing antitermite treatment from the plinth beam and brick masonry with super structure in contract with the back fill earth and at the junction of the walls. The top surfaces of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide 'Chloripyrifos' and spraying the same termicide soultion on the wooden frames and treating the other periphery of building etc., Complete in all respects as per IS 6316 (Part II) and as directed by the Project Officer.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the Project Officer.

Providing and laying of Gravel including cost and conveyance of the same to work site from approved quarry including stacking the same to departemental gauge for premeasurement including all labour charges for laying, spreading, including all hire and fuel charges for power roller for compaction, etc., complete and as directed by the Project Officer

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

Construction of Granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Project Officer With material conforming to Grade-I (size range 75 mm to0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregates for Wet Mix Macadam 250mm thick, including premixing the materials with water at OMC in mechnanical mix plant, conveyance of mixed materials by tipper to site, laying in uniform layers using pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Providing and laying Prime Coat over WBM/ WMM surface using 7 Kg of Emulsion Bitumen (SS1) per 10 Sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 502 of MORTH Rev-5

Providing and laying Tack Coat over Existing BT surface using 2 Kg of Bitumen Emulsion (RS1) per 10 Sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 503 of MORTH Rev-5

Providing, laying 90mm consolidated thick Dense Bituminous Macadam using 0.40Cum of 37.50-13.20mm, 0.35Cum of 13.20-2.36mm and 0.36Cum of 2.36mm & below size IRC metal with 71.30kgs of VG30 grade bitumen for premixing per 10Sqm including cost and conveyance of all materials to CMP site, heating the bitumen, aggregate and mixing them in the required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to site, spreading the mix to uniform thickness of 75mm with mechanical paver to the specified grades and cross sections and consolidated by Vibratory Roller to the required density etc., including labour for attending to paver to site etc., including hire and fuel charges for 20-30t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory roller and all other tools and plant required, including all other incidental charges etc., complete as per specification using CMP as per clause 505 of MORTH rev-5.

Providing and laying Bituminous Concrete to 40mm thick using 0.13 Cum of 19.00-9.50mm, 0.17 Cum of 9.50-2.36mm and 0.26 Cum of 2.36 and below with 50.30kgs of VG30 bitumen for premixing per 10Sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5

Providing and laying compacting open graded Premix Carpet 20mm thick with a liquid Seal Coat which shall consist of open graded carpet of 20mm thickness in a single course composed of suitable small sized aggregates premixed with VG30 Grade bituminous binder with application of liquid seal coat for sealing the voids in a bituminous surface conforming to the specifications including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per MORTH Rev-5 (Mix-in-place method)

Supplying and laying of Rubber moulded hydraulic pressed Paver Block Stone 63mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials, laying and Labour charges etc., The Item shall include filling the gaps with crushd stone sand. Base layer of crushed sand stone shall be measured under seperate item.

Supplying and laying of Rubber moulded hydraulic pressed Paver Block Stone 83mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials, laying and Labour charges etc., The Item shall include filling the gaps with crushd stone sand. Base layer of crushed sand stone shall be measured under seperate item.

Supplying and fixing of pre-cast kerb stone of size 450x300x150mm made in CC 1:3:6 (One of cement, three of sand and six of hard broken stone jelly) using 20mm size hard broken stone jelly including the cost of Kerb stone moulding, laying, curing, transporting, pointing and as directed by the Project Officer.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Project Officer before use on works.)

Painting new iron works such as steel doors, Grills, windows, ventilators, window bars, balustrades, PVC/ASTM Pipes, Kerb Stone etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Project Officer before use on works.)

Providing and applying 2.5 mm thick road marking strips (retro?reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Project Officer and accordance with applicable specifications

Providing Speed Breakers As Per IRC Design [Clause 5 6 of Irc: 99- 1988] With Bituminous Concrete (As Per Clause 509 of Mort&H Specification) To The Required Grade Level And Alignment And Rolled With Vibratory Roller Etc. Complete And As Directed By Project Officer And As Per The Plan Enclosed for Bus Route Roads

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Project Officer

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Project Officer.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Project Officer.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the Project Officer etc. complete complying with standard specification.

PART-2-CEMENT CONCRETE - PCC & C.C.Works

Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly inclusive of shoring, strutting, bailing out water, ramming, curing etc. complete in all respect by the Project Officer.

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly inclusive of shoring, strutting, bailing out water, ramming, curing etc. complete in all respect by the Project Officer.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the Project Officer.

Reinforced Cement Concrete

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the Project Officer. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

For Ground floor

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, reinforced with 8 mm dia four Nos longitudinal & 9 Nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Project Officer.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kg and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the Project Officer. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the Project Officer. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Form Work

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc.complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Footing, Plinth Beam, etc.

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cmx60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre supported by caurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the RCC works etc., complete complying with standard specifications and as directed by the Project Officer.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.30 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc.,complete complying with standard specification and as directed by the Project Officer.

Reinforcement Steel

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

50mm Thick

75mm thick

100mm Thick

Supplying and fixing in position SFRC manhole covers with frames (Heavy duty) of size 60cm Dia of best approved quality as per standard specification etc., complete compying with standard specifications

Supply & fixing of PVC mould CI Steps for Sump

Supply and Delivery of DWC Structured Wall Polyethylene Piping Systems (Pipe with online/offline coupler and elastomeric sealing ring) with required specials non-smooth external annular corrugated and smooth internal surface (Double wall) (SN 8 Class) for non-pressure underground sewerage, drainage application generally as per IS- 16098 (Part-2) type B.

200mmDia Pipe

250mm Dai Pipe

300mm Dia Pipe

400mm Dia Pipe

500mm Dia Pipe

providing laying and fixing of following dia RCC Hume Pipe NP2 Class - IS 458/2003 in ground complete with RCC Collers, jointing with cement mortar 1:2 as Project Officer.

400mm Dia Pipe

300mm Dia

250mm Dia

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the Project Officer.

PART-3- WATER PROOFING - Terrace Waterproofing

Providing and applying single component pure Polyurethane seamless Waterproof system free of bitumen/ tar and acrylic to be applied at consumption of 1.8 kg/Sqmt to achieve a minimum 1.5mm DFT in single coat uniformly spread in entire area over a coat of approved PU primer and in two coats at specific locations where geotextile reinforcement is placed. System shall be executed as follows: 1) Surface preparation shall be done as per manufacturer specifications. 2) Providing and applying 100 x 100mm thick fillet using cement concrete M15 grade mixed with polymer as per manufacturer's specification.

3) PU primer application at 0.2-0.25 kg/ Sqm. 4) After 4 hours, PU waterproofing can be applied by roller, spray or short hair brush PU waterproofing. Waterproofing shall be taken covering entire parapet wall and pedestals, upstands upto min 300mm. The minimum reinforcement 100mm width strip of 60gsm PP geotextile on typical locations like wall & floor junctions, chimnies etc. shall be embedded between two coats as per manufacturer's specifications. 5) Providing and laying 300 GSM geotextile above waterproofing coating as separation and protection layer 6) Protection screed laid to slope which shall be paid in relevant tender item.

All the areas where water proofing is exposed to UV, shall be protected with single component UV stable top coat. UV top coat shall be paid in relevant tender item. Rate includes all operations specifed above.The plan area of the treated surface shall be measured for payment.

Grading For Terrace Floor with 1:2:4: Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the Project Officer.

TOILET WATER PROOFING

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the Project Officer etc. The rate inclusive of cost of materials and labour, etc., complete.

Toilet Sunken using broken brick jelly 20 mm gauge The proportion of broken brick jelly to slaked lime being 1:3:6 (1part cement,3 part fine aggregate & 6 part broken brick jelly), well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Project Officer.

UG TANK - EXTERNAL WALL SURFACES

Providing and applying 2mm thick acrylic polymer modified cementitious waterproofing treatment to any type of RCC wall areas from outside after proper surface preparation, treatment of construction joints using polymer modified mortar prepared by using SBR Latex- screed modifier Cum bonding agent and application of two coats (Eachcoat of 1mm thickness) Two component acrylic polymer modified cementitious coating as per manufacturer's specification etc. complete including all tools and tackles as directed by Project Officer. The top coat shall be protected with 12 mm thick cement plaster in CM 1:4(1 cement: 4 fine sand). The rate includes cost of all elements including cement plaster specified above

UG TANK- INNER WALL AND SLAB

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush.

The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Project Officer. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per Sqm

For horizontal surface one coat @1.10 kg per Sqm.

UG TANK- BELOW RAFT, ON TOP OF PCC

Providing and applying Elastomeric Polymer modified cementitious waterproofing treatment @ 2kg/Sqm in two coats to any horizontal surfaces of Concrete, on top of PCC below raft after proper surface preparation, treatment of construction joints using polymer modified mortar, cement and sand in ratio of 1:7: 21 (1 polymer: 7 cement: 21 sand) and application of two coats with Elastomeric Polymer modified cementitious waterproofing by reinforcing 45GSM glass fibre mesh in between two coats as per manufacturer's specification etc, complete including all tools and tackles as directed by the Project Officer

Note: All the waterproofing treatment shall be executed through a specialized waterproofing agency authorised by the approved manufacturer and/or Project Officer. Contractor shall submit technical data sheet of Eachproduct, which shall use for execution.

A written guarantee on non-judicial stamp paper shall be submitted by the main Contractor and his sub contractor who has carried out work for a minimum period of ten years from the certified date of completion for the satisfactory performance of the entire water-proofing system.

water proofing works shall be executed under supervision of technical person of manufacturer. Contractor shall test all elements before and after water proofing treatment as directed by Project Officer. Rate shall include for testing process before and after water proofing treatment.The rate includes giving 10 year warrenty for waterproofing on a Rs.100/- stamp paper in approved proforma.

NOTES: 1.Ponding test shall carried out on the mother slab 2. Rectification shall be carried out in case of leakages like crack treatment, grouting,etc to arrest the leakage. 3. Ponding test shall be carried out once again to check for leakages. 4. Once there are no leakages, waterproofing treatment shall be carried out, else the procedure shall be repeated. 5. Payment will be only once for the water proofing

PART-4-ARCHITECHTRAL WORKS - Masonry Works

Masonry work using Autoclaved Aerated cement blocks of size 600 x 200x 200 mm in Self curing AAC Joint Mortar 2 to 3mm thick in between the blocks with a spread of 170Sqft / 50kg,cement Motar (1:6) (one of cement and six of M Sand) along the boundaries using AAC Block 600x 200x 200mm)minimum average crushing strength of 50Kg/sqcm for super structure in all floors including labour for fixing the doors , windows and ventilator frames in position fixing of hold fast , scaffolding ,curing etc complete in all respects complying with relevant standard specifications and drawings and as directed by the Project Officer. (The Board approved Acc Block should got approved by the competent authority before execution of work)

Masonry work using Autoclaved Aerated cement blocks of size 600mm x 200mm x 100mm in Self curing AAC Joint Mortar 2 to 3mm thick in between the blocks with a spread of 170Sqft / 50kg,cement Motar (1:6) (one of cement and six of M Sand) along the boundaries using AAC Block 600mm x 200mm x 100mm)minimum average crushing strength of 50Kg/sqcm for super structure in all floors including labour for fixing the doors , windows and ventilator frames in position fixing of hold fast , scaffolding ,curing etc complete in all respects complying with relevant standard specifications and drawings and as directed by the Project Officer. (The Board approved Acc Block should got approved by the competent authority before execution of work)

Solid Concrete blocks:Providing and constructing 200mm thick solid cement concrete block masonry work at all levels in cement mortar 1:4 using standard size of 400mm x 200mm of solid cement concrete blocks of thickness as given below, with minimum compressive strength of 3 N/Sq mm confirming to IS 2185 or equivalent BS, all scaffolding, staging, curing, and including chicken mesh, etc all complete as per standard specification.

Flooring

Suppling and laying of Stain Free Nano Polish Vitrified Tiles 600x600x8mm in CM 1:3 20mm thick including fixing in position, cuting the tiles to the required size wherever necessary, pointing the joints with grout (Tile joint filler) curing, finishing etc., all complete and as directed by the Project Officer.

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Project Officer before use on works)

First Quality Design Ceramic tiles of All colours of size 305 x 305 x 6mm

Supplying and fixing of following best approved quality, white / colour glazed tiles of following sizes over cement 1:3 (one cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with grout (Tile joint filler) curing, finishing etc., all complete and as directed by the Project Officer.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Project Officer concerned before use on work, etc., complete as per standard speicification.

Using Fine polished Kota Stone Slab above 600 x 600 of 18 / 20mm size

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments, including Nosing etc.complete, The granite stone slabs and other materials to be used shall be got approved by the Project Officer concerned before use on work, etc., complete as per standard speicification.

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the Project Officer. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the Project Officer) 50mm Thick

Providing and laying 2mm thk Anti static vinyl flooring including joints to be perfect machine like straight cut without jagged edges, welded at joints. The Surface to be smooth and in level without any bubbles or creases. The rate to be inclusive of self levelling required due to undulations in the floor

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Project Officer.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Granite flooring : Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Project Officer : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing & laying of roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately).

Plastering Works

Plastering the surface of walls with Cement Mortar 1:5 (One cement and five plastering sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the Project Officer.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar Nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the Project Officer

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., in all floors including necesary band, drip moulds, curing etc., complete complying with standard specification and as directed by the Project Officer.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Project Officer concerned before use on work, etc., complete as per standard speicification.

Using Fine polished Kota Stone Slab above 600 x 600 of 18 / 20mm size

Suppling and laying of Stain Free Nano Polish Vitrified Tiles 600x600x8mm in CM 1:3 20mm thick including fixing in position, cuting the tiles to the required size wherever necessary, pointing the joints with grout (Tile joint filler) curing, finishing etc., all complete and as directed by the Project Officer.

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Project Officer before use on works)

First Quality Design Ceramic tiles of All colours of size 305 x 305 x 6mm

Supplying and fixing of following best approved quality, white / colour glazed tiles of following sizes over cement 1:3 (one cement and three of sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with grout (Tile joint filler) curing, finishing etc., all complete and as directed by the Project Officer.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments, including Nosing etc.complete, The granite stone slabs and other materials to be used shall be got approved by the Project Officer concerned before use on work, etc., complete as per standard speicification.

Joinery

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Solid panel PVC door with frame

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The window should be got approved from the Project Officer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Project Officer before use on work

Supplying and erecting pull and push type rolling shutter with grills, ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Electrically Operated Type (exceeding 12 Sqm. Area)

Note for items of this Section : Contractor shall prepare shop drawing based on intent/ concept drawing and submit the same to Project Officer for approval and shall get approval before mockup/ execution of work. Work shall be carried out as per final approved shop drawing and approved mock up. Contractor shall responsible against stability, safety, leakage, etc all complete.Testing work shall be carried out by the Contractor as suggested by Project Officer

Providing and fixing of Hollow metal 2 Hour fire rated doors as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall have prototype tested by CBRI, Roorkee & Certificate issued thereof (as per IS:3614 Part-2, 1992) for rating of 2hrs with vision panel.

Test certificates should be available for vision lites/ panels as part of the fire door assembly. Manufacturer test certificate shall cover doors both single & double leaf doors and Hardware should pass European certificate "CE" of conformity/ UL with required fire ratings. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer subject to Project Officer’s approval and should be ISO Certified company.

a) Fire rated Door frame shall be double rebate profile of size 143 x 57 mm made out of 1.60mm minimum thick galvanized steel sheet. Frames shall be Mitered and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb.

Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening. EPDM Smoke seal shall be installed over frame. Frames shall be finished with approved shade powder coated paints with an average DFT of 70 microns and tested for salt spray test of 500hrs.

Rate shall be inclusive of frame, back plate, rubber silencer, smoke seal, SS 304 anchor fastener, cement mortar grout filling finishing of frame and installation at all heights but excluding the cost of SS ball bearing hinges. Length of the door frame provided shall be measured in running metre for payment.

b) Fire rated Door shutter shall be minimum 46mm thick fully flush double skin door with or without vision lite. Door shutter shall be manufactured from 1.2mm minimum thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be with resin bonded rockwool slab. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers.

The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Shutter shall be fixed to frame with 120 min fire rated SS 304 Ball Bearing Butt Hinges of size 100mm x 75mm x 3 mm CE marked (no of hinges shall be minimum 4). Shutter shall be provided with bottom seal of approved make as per manufacturer's specification.

Vision lite wherever applicable should be provided as per manufacturer’s recommendation with a GI beading and screws from inside. Door shutter shall be finished with approved shade powder coated paints with an average DFT of 70 microns and tested for salt spray test of 500hrs. Rate shall be inclusive of shutter with infill material, SS304 fire rate butt CE marked hinges, finishing cost and installation but excluding the cost of Vision panel and all fire rated hardware other than hinge. Shutter area shall be measured for payment.

c) Providing and fixing fixed vision panel glass in fire rated door as per manufacturers recommendation with beading powder coated to required shade & special ceramic tape/ gasket of approved make etc complete as directed by Project Officer The glass should be 6mm clear borosilicate fire rated glass of 2 hour rating of approved make. (Actual installed glass size (with two decimal) to be measured for payments).

Providing and fixing 120 min fire rated Mortise sash lock pack of approved make with 70 mm Cylinder one side lock and other side Thumb turn with Lever CE marked for fire rated metal door with necessary fittings etc. complete as recommended by manufacturer and as directed by Project Officer

Providing and fixing Fire rated (120 minutes) Rack and pinion non-handed door closer of approved make and comply with EN size 2-4, with back check and standard arm with two independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed with slide plate. The door closer shall be with Silver finish cover. The door closer shall conform to EN 1154 standards and CE marked with necessary fittings etc. complete as recommended by manufacturer and as directed by Project Officer

Providing and fixing 1 point panic device in Contour design of approved make, carry bar for single door for fire and smoke check doors, with steel latch, security anti thrust latch for door widths upto 1300mm, consisting of 2102F, 2105 in silver finish. As per EN 1125, CE marked etc. complete as recommended by manufacturer and as directed by Project Officer

Providing and fixing 1 point panic device in Contour design on active leaf and 2 point modular on inactive leaf, carry bar for rebated double door of approved make. For fire and smoke check doors, with steel latch, security anti thrust latch consisting of 2 x 2102F, 2 x 2105, PHX 04 and PHX 03 in silver finish. As per EN 1125, CE marked with necessary fittings etc. complete as recommended by manufacturer and as directed by Project Officer

Providing and fixing External trim with design lever handle approved make suiting the panic bar for fire and smoke check doors. For max. 60mm thick door prepared for half euro profile cylinder and in Silver finish with necessary fittings etc. complete as recommended by manufacturer and as directed by Project Officer

Supplying and erecting pull and push type rolling shutter with grills, ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Gear Operated Type (from 8 Sqm. to 12 Sqm. Area)

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Both side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 3 Nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 1no Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification.

Door Frame:Supplying and fixing first quality teak wood frames for doors, windows, ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc. complete in all floors.

Teak Wood Scantling 2m in length

Supplying and erecting pull and push type rolling shutter with grills, ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Manually operated (up to 8 m2 area)

Painting

Supplying and painting the walls with two coats of wall putty as instructed by the Project Officer including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Project Officer before use of work).

Wall painting with two coats premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including one oat of primer wherever required to achieve even shade and colour.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Project Officer before use of work).

Painting the new wood work with three coats of best approved wine varnish etc., complete in all respects complying with relevant standard specification and as directed by the Project Officer ( The quality and shade of paint should be got approved by the Porject Officer before use).

PART-5-MEP - Domestic water supply pumps

Supply, Installation, Testing and commissioning of Domestic water supply pumps consisting of the following specifications

Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS. M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal, Base Frame: MS. Along with fixed speed control panel Control Panel consisting of the following component: i) A dedicated logic controller control unit c/w preprogramed microprocessor chip ii) Pump monitoring unit to monitor the operation of the pump sets iii)Pressure Transmitter iv)Automatic operation v)Manual and emergency operation vi)Automatic sequence change vii)Set point viii)Frictionless compensation" ix)Displays x)Pump status and Zone Status

Technical Parameters :

Flow - 118 Cu.M/ Hour at 10 MWC) - 10HP with 2000LPM fixed speed motor for Eachpump.

No. of Pumps - 2 ( 1 working + 1 standby)

Mono Submersible pump

Supplying and installing Mono Submersible pump set 1HP and (166LPM) having air flow rate 10 m3/hr with 10 mtr head working on three phase 50 Hz, 415 V +/- 10% with base plate, DOL starter, Cable, along with control panel, GI Medium duty delivery pipe, specials, etc. complete set. MOC Impeller-Bronze, Casing - C.I. Shaft - SS / Bronze

Supplying and installation testing & commissioning of PLC Integration for controlling pumps based on AI-8, DI-16, AO-3 & DO-8 Schedule with sensor and suitable current relay for main control valve.

PLC / SCADA System shall have to interface with ICCC. The bidder / contractor shall consider the required hard wired / soft integration communication module along with the PLC / SCADA system

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 200mm diameter

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 150mm diameter

Supplying and installation of G.I. pipes complete with G.I. fittings etc complete. 50 mm dia. nominal bore

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 200mm diameter

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 150mm diameter.

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 50mm diameter.

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 200mm diameter

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 150mm diameter

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 50mm diameter

Supplying and installation of 200NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying and installation of 150NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying, fixing and testing of 200mm GI Puddle Flange and Flange 15mm thickness, Center plate 6mm thikness, for inlet, outlet, vent and overflow pipes, shown on the drawings etc.,

Supplying, fixing and testing of 100mm GI Puddle Flange and Flange 10mm thickness, Center plate 6mm thikness, for inlet, outlet, vent and overflow pipes, shown on the drawings etc.,

Supplying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 200 mm dia Ductile Iron Class K-9 pipes

Supplying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 150 mm dia Ductile Iron Class K-9 pipes

Supplying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 100 mm dia Ductile Iron Class K-9 pipes

Supplying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 80 mm dia Ductile Iron Class K-9 pipes

Chamber Air release valve

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 having small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, with built-in Kinetic features, isolating sluice valve mounted in horizontal position and operated by wheel gearing, inlet face and drilled, including insurance, inspection charges, loading, unloading, transportation, in all respect etc. complete.

50mm diameter - 6Nos (On 200NB, 150NB & 100NB)

20mm diameter - 1no (On 80NB)

Chamber CI Sluice valve

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 200 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 150 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 100 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 80 mm dia valve in Chamber

Supply, installation, testing and commissioning of Electromagnetic Flow Meter shall be a velocity sensing Electromagnetic type, microprocessor based signal converter, sealed housing, flanged tube meter for 1.0 Mpa working pressure, manufactured to highest standard available for mag-meters, equipped with minimum six digit digital totalizers, reading in different units (Kiloliters / Cubic meter) and shall be accurate within 0.5% of Measured value, shall operate within a range of 0.3 m/sec to 4 m/sec and be constructed as follows: Meter tube (Sensor) shall be fabricated from stainless steel tube and use class PN10 flat face carbon steel flanges in accordance with IS 1538. These flanges shall be welded to the flow tube. The internal and external of the meter tube shall be blasted to near white and lined with hard rubber/ Polyurethrene/ PTFE preferably by SBR or EPDM. Meter tube shall have a constant nominal inside diameter offering no obstruction to the flow. The accuracy should be inclusive of linearity, hysteresis, repeatability, temperature and pressure effects. Coil Housing shall be fabricated from stainless steel (SS304)/ Die cast Aluminium/ Carbon steel with anticorriosive paint for corrosion resistance and welded to the tube providing a completely sealed environment for all coils, electrode connections and wiring harness capable of submerged or buried operation with IP68 Protection. Signal Converter shall be pulsed DC coil excitation type with auto zeroing. The signal converter shall be remotely mounted away from the meter. The converter shall indicate direction of flow and provide a flow rate indication and a total of flow volume for both forward and reverse directions. The converter shall provide an isolated 4-20 mA output into minimum 500-ohm load and a frequency output of a maximum of 0-10 KHZ and a scaled pulse output. The microprocessor based ignal converter shall have a self-diagNostic test mode and a backlit display that continuously displays “Rate of Flow” and “Total Volume”. Converter shall be supplied with a programmable low flow drop out, higher flow and empty pipe zero return. The signal converter housing should be die-cast aluminum with glass window. The converter Cum transmitter should be fully programmable from the front facia. The programming should be user friendly, self-prompting menu driven. Flow meter test calibration certificate from FCRI, flow test lab / NABL accredited lab to be furnished.

200mm Dia

Flushing Net work

Flushing water supply pumps

Supply, Installation, Testing and commissioning of Flushing water supply pumps consisting of the following specifications

Horizontal end suction centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS. M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal, Base Frame: MS. Along with fixed speed control panel Control Panel consisting of the following component: i) A dedicated logic controller control unit c/w preprogramed microprocessor chip ii) Pump monitoring unit to monitor the operation of the pump sets iii)Pressure Transmitter iv)Automatic operation v)Manual and emergency operation vi)Automatic sequence change vii)Set point viii)Frictionloss compensation" ix)Displays x)Pump status and Zone Status

Technical Parameters :

Flow - 83 Cu.M/ Hour at 10 MWC) 7.5HP with fixed speed motor for Eachpump."

No. of Pumps - 2 ( 1 working + 1 standby)

Supplying and installation testing & commissioning of PLC Integration for controlling pumps based on AI-12, DI-16, AO-8 & DO-9 Schedule with sensor and suitable current relay for main control valve.

PLC / SCADA System shall have to interface with ICCC. The bidder / contractor shall consider the required hard wired / soft integration communication module along with the PLC / SCADA system

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 125mm diameter"

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 125mm diameter.

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 125mm diameter

Supplying and installation of 125NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying, fixing and testing of 150mm GI Puddle Flange and Flange 12mm thickness, Center plate 6mm thikness, for inlet, outlet, vent and overflow pipes, shown on the drawings etc.

Supply and laying in standard lengths(6 metre) High Density Polyethylene (H.D.P.E) Pipes, confirming to IS 4984:1995 and IS 7328:1992 (amended up to date), including all local & central taxes, transportation and freight charges inspection charges, loading / unloading charges, conveyance to the site of work & stacking the same in closed shade duly protecting from sunrays, rain & theft or physical damage, etc. complete. material grade PE 100 / PN 10

180Dia HDPE Pipe line

140Dia HDPE Pipe line

110Dia HDPE Pipe line

75Dia HDPE Pipe line

50Dia HDPE Pipe line

Chamber CI Sluice valve

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 140 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 100 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 75 mm dia valve in Chamber

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 50 mm dia valve in Chamber

PART-6-ELECTRICAL WORKS-RMU

Design, Supply, installation, testing and commissioning of '11KV,21KA,630A,RMU: Outdoor type RMU with 2 Nos. 630A Load Break Switch with earth switch as incomers and 1 no. 630A,26.3kA,3P,11kV VCB Vacuum Circuit Breakers as outgoing. Switchgear shall be IP -65, trench mounting type with necessary accessories. The RMU shall comply with DAS enabled facility & Metering as per TANGEDCO Specifications. The panel shall be of extensible type. All CT ,PT Ratio shall be as per final requirement of TANGEDCO

Note 1: The Procurement of RMU should comply with TANGEDCO requirement upto dates.

11kV HT Panel (Outdoor Type)

Design, Supply, installation, testing and commissioning of THREE VCB panel, comprising of 1set of 11KV, 630A, 650MVA, 26.3kA VCB as Incomer and 2set of 11KV, 630A, 650MVA, 26.3kA VCB as Outgoings with all required necessary accessories. HT Outdoor three VCB Panel Board with all accessories and all metering, protection for satisfactory operation and as required by the statutory Electrical authorities as per the detailed specification and SLD enclosed. The panel shall be extendable at both sides. The cost is inclusive of suitable rating of built-in power pack for all control wiring. Outgoing feeders shall be provided with Transformer protection relays. The Panel shall be OEM system Integrated type with air insulated switch gear along with arc flash relays in all the compartments. No Separate DC supply will be Provided.

1.25MVA Transformer

Supply, installation, testing and commissioning of 1.25MVA, 11kV/433V Outdoor, Oil cooled ONAN type Transformer with on load tap changer (OLTC) & RTCC panel as per the detailed specification enclosed. Transformer Protection relays should be provided at Each Transformer such as Transformer restricted earth fault relay,OLTC surge relay, temperature relay, winding temp relay, Auxiliary relays as per standards. Neutral CT of 2000A CL PS for Restrictred earth fault Protection. The transformer shall be provided with cable termination box on HT side to terminate 3 core 300 Sqmm XLPE cable and suitable for terminating Out Door Type Sandwhich type aluminium bus duct on LT side 2000A Amps rating all as per the detailed specification enclosed. Transformer losses shall be designed for Level 2.

LT ACB KIOSK (Outdoor type)

Design, Supply, testing and commissioning of cubicle type floor mounting switch board suitable for side bus duct entry and comprising of the following, the board shall be fabricated as per the detailed specification enclosed. 2000A LT KIOSK PANEL:

2000 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 1 No. Metering for Incomer: 1No-Load Manager with RS485 Modbus 1Set-2000A/5A,class0.5,15VA Cast resin CT' s for metering 1set - R,Y& B Indication lamps 1set - ACB ON, OFF& TRIP indication lamps 1set - ACB T/N/C Switch 1Lot -Control MCBs 1Set - 64R relay with Phases/ Neutral side CT's & interconnections EB busbar: 2000A 4P Aluminium bus bars, interconnections with colour coded heat shrinkable sleeves and SMC Bus bar supports.Bus bar supports,Current density of the Bus bars shall not exceed 0,8 A/sq.mm Terminal arrangement: Incoming: Side entry bus duct Outgoing: Side entry bus duct

Single ACB Panel (Outdoor type)

Design, Supply, testing and commissioning of cubicle type floor mounting switch board suitable for top/ Bottom cable entry and comprising of the following, the board shall be fabricated as per the detailed specification enclosed. 1600A LT ACB Panel:

1600 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 1 No. Metering for Incomer: 1set - R,Y& B Indication lamps 1set - ACB ON, OFF& TRIP indication lamps 1set - ACB T/N/C Switch 1Lot -Control MCBs EB busbar: 1600A 4P Aluminium bus bars, interconnections with colour coded heat shrinkable sleeves and SMC Bus bar supports.Bus bar supports,Current density of the Bus bars shall not exceed 0,8 A/sq.mm Terminal arrangement: Incoming: Cable Outgoing: Cable

Main LT Panel

Design, Supply, testing and commissioning of cubicle type floor mounting switch board suitable for top cable entry and comprising of the following, the board shall be fabricated as per the detailed specification enclosed and 630 A & above panel incomer shall be fully Type tested panel as per IEC 61439.(Quote shall be taken from approved Panel Manufacturer) Main LT PANEL

INCOMING

2500 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 2 No. 2000 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 2 No. BUSCOUPLER 2500 Amps 4 Pole EDO 50kA Type Microprocessor based ACB Buscoupler with all other accessories - 1 No. INTERLOCK Electro - Mechanical interlock (3 Lock + 2 Key)

OUTGOINGS

1600 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 1 No. 1250 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 2 No. 800A TPN MCCB, 36kA – 2 Nos 630A TPN MCCB, 36kA – 4 Nos 400A TPN MCCB, 36kA – 3 Nos 200A TPN MCCB, 36kA – 6 Nos 160A TPN MCCB, 36kA – 2 Nos 100A TPN MCCB, 36kA – 4 Nos All outgoings MCCB shall be microprocessor based

Both incomers shall be interlocked with electrical and mechanical arrangements by hardware control wiring along with. Also providing protection relays and meters with necessary CT / PT, control MCB/ MPCB/ RCBO etc. and all as per the detailed specification and drawings enclosed. Both incoming breakers should be provided with built-in microprocessor based release with overload, short circuit and earth fault releases.

Incoming metre for both incoming feeder shall be with All Outgoing Feeders in Main panel shall be with MFM monitoring like Harmonic THD and individual harmonic display+ Regular parameters like V, I, KVA, KVAR, KW, KWH, KVARh, PF, Freq, Max, AVG etc. All Outgoing Feeders in Main panel shall be with KWH meter. All the metres to be wired and terminated at common metre chamber / marshalling feeder of Eachpanel section.

2500Amps TPN 50kA 1 Sec aluminium busbars:- All the neutral busbars shall have the same capacity of phase busbars.

APFCR Panel

Design, supply, fixing, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. (APFCR Panel) Incoming: 1250A TPN EDO ACB 50kA Draw out type with Auto power factor correction relay with necessary CT, control wiring etc.- 1 No. as incomer.

Outgoing: Total 500 KVAR: 2 sets of 100KVAR (1 x 100 KVAR) with 400A TP MCCB 25KA, suitable contactors with switching steps in the rating of 100 KVAR as required. 4 sets of 50 KVAR (1 x 50 KVAR) with 160A TP MCCB 16KA, suitable contactors with switching steps in the rating of 50 KVAR as required. 3 sets of 25 KVAR (1 x 25 KVAR) with 100A TP MCCB 16KA, suitable contactors with switching steps in the rating of 25 KVAR as required. 2 sets of 10 KVAR (1 x 10 KVAR) with 40A TP MCCB 16KA, suitable contactors with switching steps in the rating of 5 KVAR as required. 1 sets of 5 KVAR (1 x 5 KVAR) with 32A TP MCCB 16KA, suitable contactors with switching steps in the rating of 5 KVAR as required.

1250Amps TP 50kA 1 Sec aluminium busbars:- All the neutral busbars shall have the same capacity of phase busbars.

Storm Water Pumping Panel

Design, Supply, testing and commissioning of cubicle type floor mounting switch board suitable for top cable entry and comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Storm Water Pumping Panel

INCOMING

Change over switch - 1 No. 1600 Amps 4 Pole EDO ACB 50kA Type Microprocessor based with all other accessories - 1 No.

Metering for Incomer: 1No-Load Manager with RS485 Modbus 1Set-1600A/5A,class0.5,15VA Cast resin CT' s for metering and MDC 1set - R,Y& B Indication lamps

OUTGOINGS

630 Amps 4 Pole EDO 50kA Type Microprocessor based with all other accessories - 2 No. 630A TPN MCCB, 36kA – 7 Nos 63A TPN MCCB, 25kA – 3 Nos

Incomers shall be provided with meters with necessary CT / PT, control MCB/ MPCB/ RCBO etc. and all as per the detailed specification and drawings enclosed. incoming breakers should be provided with built-in microprocessor based release with overload, short circuit and earth fault releases.

1600Amps TPN 50kA 1 Sec aluminium busbars:- All the neutral busbars shall have the same capacity of phase busbars.

Valve DB - VTPN DB

Supply, fixing, testing and commissioning of the double door type VTPN 8 way MCCB DB comprising of the following :

63A 4P MCCB 25kA – 1No. as incomer with ELM

32A 4P MCB 10KA (C-Curve) – 8 Nos. as outgoings. With all outgoing Indication lamp - (ON/OFF/TRIP)

With necessary tinned copper busbars, interconnections, earth bus, neutral bus. The board shall be powder coated type fixed with concealed system in wall/ fixed in column. The rate shall include necessary connected civil works like chipping, rough plastering etc.

UPS Panel (Indoor type)

Design, Supply, testing, commissioning, transporting and unloading of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification and drawings enclosed. UPS PANEL

Incoming

1 No. 63 Amps 4P 25 KA MCCB all other accessories.

Instrumental compartment for both incomers

Digital type Multi function meter, CTs, RYB Indication lamps with PT((415V/1.732)/(110V/1.1.732)), MCB, MPCB(1.0to1.6A) & RCCB(10A, 30mA) and “ON/OFF/Trip" indicating lamp, CBCT with ELR(0-12A), LED display etc.,

Outgoing

32 A DP MCB - 10 Nos.

With necessary Aluminium busbars, interconnections, neutral link, Aluminium Aluminium busbar for cable termination, door interlock and all other necessary accessories etc,

63 Amps TPN Aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars.

Water Pump Panel

Design, Supply, testing, commissioning, transporting and unloading of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification and drawings enclosed. WATER PUMP PANEL

INCOMING

100A TPN MCCB (Motorized) 25kA with connected accessories – 2No.as incomer

INTERLOCK Electrical Interlock system

Instrumental compartment

Digital type Multi function meter, CTs, RYB Indication lamps with MCB, MPCB (1.0to2.0A) and “ON/OFF/Trip" indicating lamp, CBCT with ELR, LED display etc.,

OUTGOING

32A 4P MCCB 25kA - 11 Nos.

With necessary Aluminium busbars, interconnections, neutral link, suitable Aluminium busbar for cable termination, door interlock and all other necessary accessories etc,

100 Amps TPN Aluminium busbars:- All the neutral busbars shall have half the capacity of phase busbars.

Feeder Pillar - 1,3

Supply, fixing, testing and commissioning of the double door type compartmental Phase segregated 6way DB type Panel comprising of the following : Feeder Pillar - 1,3

200A 4P MCCB 16kA with all necessary connected accessories – 1No.as incomer

63 A DP Contactor – 3 Nos. as individual phase incomers

63 A DP RCCB 100 mA – 3 Nos. as individual phase incomers

Each63 A SP 10k MCB outgoing consist of 18 Nos (C-Curve) in a separate compartment with necessary phase segregation as required by the Electrical Inspectorate.

32 A 4P MCB outgoing consist of 5 Nos including Indication lamp (ON/OFF/TRIP) With timer which is suitable for Soft integration with BMS.

With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for Eachphases. The board shall be powder coated type fixed with concealed system in wall/ fixed in column. The rate shall include necessary connected civil works like chipping, rough plastering etc.

200 Amps TPN Cupper busbars:- All the neutral busbars shall have half the capacity of phase busbars.

Feeder Pillar -2,4

Supply, fixing, testing and commissioning of the double door type compartmental Phase segregated 6way DB type Panel comprising of the following : Feeder Pillar - 2,4

63A 4P MCCB 16kA with all necessary connected accessories – 1No.as incomer

63 A DP Contactor – 3 Nos. as individual phase incomers

63 A DP RCCB 100 mA – 3 Nos. as individual phase incomers

Each63 A SP 10k MCB outgoing consist of 18 Nos with (C-Curve) in a separate compartment with necessary phase segregation as required by the Electrical Inspectorate. With timer which is suitable for Soft integration with BMS.

With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for Eachphases. The board shall be powder coated type fixed with concealed system in wall/ fixed in column. The rate shall include necessary connected civil works like chipping, rough plastering etc.

63 Amps TPN Cupper busbars:- All the neutral busbars shall have half the capacity of phase busbars.

DIESEL GENERATING SET 1010KVA

DG SET Supply, Installation, Testing and Commissioning of factory assembled and factory tested, radiator cooled, turbo charged after cooled diesel engine alternator set capable of generating full load of 1010 KVA capacity at 50° C, power factor not less than 0.8 lag, 415 Volts, 1500rpm, 3 phase, 50 Hz, AC supply and driven with diesel engine complete with all accessories such as Base frame, residential silencer, radiator, alternator capable of delivering 415 Volts, 50Hz, 3 phase, PF 0.8, 1010 KVA load, coupling arrangement of alternator with engine, coupling guard, anti-vibration mounts suitable for 1010 kVA DG set, oil tanks of 990 ltrs with flame proof level switch., High speed diesel oil (990Ltrs). fuel filter, oil filter, air filter, exhaust flexible piping, suitable batteries for starting / charging purpose , battery charging alternator, engine control panel, etc. (the anti-vibration mounting quantity as per the manufacturer's recommendation), Note : The successful tenderer should confirm that the engine model shall be capable of delivering minimum 1010KVA and suitable for delivering 1010 KVA when coupled with alternator given below at site condition as required. The Acoustic Enclosure is included seperately in below.

The D.G. Set shall be housed in weather proof enclosure & sound proof canopies fabricated out of 16 SWG CRCA sheet hot rolled MS channel or CRC cold formed pre-fabricated Steel sections, assembled at site with suitable fasteners door to be provided with EPDN gaskets. The acoustic container shall be made of modular construction for easy assembling and dismantling. Make - powerica, Appolo Power Systems, Genlite Engineeing Pvt Ltd,

ACOUSTIC ENCLOSURE 'Supply, Installation, Testing and Commissioning of powder coated acoustic enclosure suitable for 1 No. 1010 KVA radiator cooled diesel generator with all accessories fabricated with 16 SWG CRCA sheet steel, mineral wool insulation of high density with perforated GI sheet covering, ventilation system complete with fans and louvers, doors, inside temperature controller, inside illumination with energy efficient LED light fittings, wiring for light and plug points with suitable size and number of PVC insulated copper conductor cable on surface MS conduit system, i/c. MCB type distribution board, earthing complete as per the Specification. The enclosure should have necessary cooling fan (fresh air and / or exhaust fan) to be fixed inside the canopy with all accessories as required including ventilation system. No duration in DG set capacity shall be accepted on this account. (The above enclosure should be as per CPCB norms. The current approval certificate shall be submitted by the firm) (Excluding cost of foundation). The necessary details such as weight (dynamic & static weight), sizes shall be furnished for the execution.

Diesel Generating Set 1010KVA described as above.

ISOLATOR PANEL 'Supply, Installation, Testing and Commissioning of 1600Amps, 4pole 36KA, MDO type air circuit breaker with shunt release, shutter assembly, door interlock and other required indication lamps and accessories with copper busbar arrangement and all as per detailed specification. The panel shall be accommodated inside the acoustic enclosure with DG to AMF Isolator panel single core cable included in this item and necessary interconnections by using copper flexible cables.

SYNCHRONIZING PANEL

Supply, erection, testing and commissioning of cubicle type floor Indoor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. SYNCHRONIZING PANEL

INCOMING 1 Nos. 1600 Amps TPN 50KA electrical draw out type Air circuit breaker with shunt release, shutter assembly and all other required necessary accessories. 200 A TPN contactor for Neutral isolation Instrumental compartment for 1010KVA DG set Incomers -1 Nos

1 Nos. 800 Amps TPN 50KA electrical draw out type Air circuit breaker with shunt release, shutter assembly and all other required necessary accessories. 200 A TPN contactor for Neutral isolation Instrumental compartment for 500KVA DG set Incomers -1 Nos

Woodwared module Check Sync Relay, Digital type KWH, CM1 (A+V+F), DLM, Battery charger unit, Annunciation window, 6 Nos 1250A/1A CL-PS for Differential protection relay (3 Nos. in Synch. Panel+ 3 Nos. in Alt. Box), 3 no 1250A/5A Cl:1 10VA 6 Nos for 750KVA. RYB Indication lamps, PT((415V/1.732)/(110V/1.1.732)), MCB, “ON/OFF/Trip" , Eng Trip indicating lamp, Breaker ON/OFF push button,DG start & stop, Emergency push button, Hooter,DC volt meter and ammeter, Differential protection relay, earth fault relay, PLC for LDSS, VSR-1 &2 with fuse etc., as required other necessary accessories for synch panel operation.

Buscoupler 1 No. 2500 Amps 4 pole 50KA electrical draw out type Air circuit breaker with shunt release, shutter assembly and all other required necessary accessories and ON/OFF/TRIP lamps Outgoings '2 Nos. 2500 Amps 4P EDO 50KA electrical draw out type Air circuit breaker with shunt release shutter assembly and all other accessories. Instruments Panel “ON/OFF/Trip" indicating lamp and phase indication lamp, PT((415V/1.732)/(110V/1.1.732)), MCB(1.0 to 1.6A), RCCB(10A, 30mA) etc.,

SYNCHRONOUZING PANEL 2500Amps TPN+E Aluminium busbars:- All the neutral busbars shall have same the capacity of phase busbars. Please refer the detailed technical specification and SLD for more references.

EXHAUST SYSTEM

Design, manufacture, supply, installation, testing and commissioning of following MS exhaust pipe fabricated from class ‘B’ MS pipes conforming to IS 3589 of size suitable to limit backpressure to within permissible limit. and it shall be insulated with 50mm thick rock wool insulation (density 75kg/cu.mtr. - to achieve a maximum temperature of 60°C on the outside surface of the insulated pipe) The insulation shall be held in position with 0.63mm diameter, 20 mesh, wrapped in galvanized steel wire mesh and finished neatly with 24 SWG Aluminium Cladding including all MS epoxy painted support structural as required suitable for 1010KVA exhaust line, as per manufacturer's recommendation upto silencer. The rate shall be inclusive of necessary, bends, flanges, gaskets, 'Y' transformation piece, fixing of residential silencer supplied along with the engine, inspection point, welding arrangements as specified to suit the site conditions. The exhaust pipe should be painted with 2 coats of high temp aluminium paint before the insulation. The tenderer shall submit calculation along with the size offered for the DG set, as detailed below, individually:-.

Design, manufacture, supply, installation, testing and commissioning of providing 300mm dia. MS exhaust pipe class' B' with 50 mm thick glass wool insulation and aluminium cladding (the pipe dia should be indicated in mm as per the manufacturers recommendation for satisfactory operation for 1010KVA.

Supply & fixing of 50mm thick glass wool insulation for 1010KVA engine residential silencer including cutting, fixing of glass wool, polythene covering, chicken mesh and aluminium cladding complete as per the specifications etc. as required.

FUEL TANKS & PIPE LINES

Supplying and laying of 25 mm dia, C class MS pipe, fuel line for the interconnection of the buffer tank /intermediate tanks to day tank and day tank to engine i/c. fuel transfer pumps with all accessories such as bend,elbow, coupling, flanges, bolts/nuts, gaskets, making threaded ends/welding as per the site condition laying in the following manner etc. as required. (The pipe line should be suitable for the function of automatic fuel filling and the overflow fuel should be return to reserve tank from the day tank automatically)

In the exposed surface the 25mm dia pipe line shall be painted with one coat of primer and two coats of synthetic enamel paint i/c. with necessary supports complete as required.

25mm dia brass gun metal ball valve (Auto actualted valve)

25mm dia float valve for day tank

Supplying and fixing of 990 liters secondary oil double jacket storage tank (Day Tank) shall be constructed from 4mm thick Mild Steel in accordance with BS 2594. Tank shall include 400 mm ID manhole cover, level indicator (Glass Tube guarded bt wire mesh cage) and flanged connection for inlet, outlet, overflow, drain, air vent, inlet fuel filter and probe provision for level controller to return automatically diesel back to bulk storage tank from the over flow tank. Tank shall be installed in civil pit at site (painted with 2 coats of red oxide primer)., with suitable size MS angle iron frame work on the existing foundation etc. as required. (Excluding cost of foundation).

Supply, Installation, Testing and commissioning of fuel transfer pumps 1 HP capacity, self priming, flame proof pumps 2Nos. (1No. Main and 1No. Standby) i/c. installation of pump sets on the existing foundation, connected fuel pipe line work with necessary control valves, to fill the reserve tank from barrels and to fill the day tanks from the reserve tanks. All electrical works such as control MCB, starter, changeover switch, control and power wiring with PVC insulated copper conductor cabling, end terminations, earthing the pumps,painting,sign writing and complete as required. (Excluding cost of foundation).

STACK FOR EXHAUST PIPE & OTHER WORKS

Supply and Installation of MS prefabricated steel structure in HDG bolt nut arrangement for 30Mtrs high exhaust pipe stack for taking total 1 number of 1010KVA and 1 number of 1010KVA DG exhaust pipe with platforms at one location with guarded ladder arrangement for climbing from ground level to top level. the structure shall be hot dip galvanised to 65 micron average thk. foundation bolts as per design to be free issued to civil contractor for embedding in RCC. necessary structure design in STAAD or ETABS to be submitted to structure consultant for approval. the structure shall have necessary 50 x6 mm GI earth strip laid in two runs from top to bottom.

Supply, fixing of 2x12W LED cluster integral type aviation lamp at top of the Chimney with Auto ON / OFF photo cell controller, connecting wires upto aviation lamp etc

Bus Duct

Design, supply, erection, testing and commissioning of 2500 Amps Indoor type Sandwich type Aluminium FP bus duct with canopywith flexible joints at Both end of the bus duct. Interval (RYBN+ PE) and with suitable support from ceiling as per the detailed specification enclosed. The busduct should be with straight run, 90 deg. Horizontal and vertical bends. (The busduct shall be Aluminium bus bars of suitable size. The busbar should be support by epoxy insulators at regular intervals) The busduct shall run from DG Sync to MLTP. The bus duct shall be fabricated as per the detailed specification enclosed. Current Density of bus bars shall not exceed 0.8 Amps/ Sq.mm. The rate includes necessary connected civil works if required and necessary supports as required at site

Design, supply, erection, testing and commissioning of 2000 Amps outdoor type Sandwich type Aluminium FP bus duct with canopy with flexible joints at Both end of the bus duct. Interval (RYBN+ PE) and with suitable support from ceiling as per the detailed specification enclosed. The busduct should be with straight run, 90 deg. Horizontal and vertical bends. (The busduct shall be Aluminium bus bars of suitable size. The busbar should be support by epoxy insulators at regular intervals) The busduct shall run from DG Sync to MLTP. The bus duct shall be fabricated as per the detailed specification enclosed. Current Density of bus bars shall not exceed 0.8 Amps/ Sq.mm. The rate includes necessary connected civil works if required and necessary supports as required at site

2500 Amp Ratings Flexible Joint

Supply, erection, testing and commissioning of 2500 Amps Aluminium flexible joints suitable for Sandwich type Aluminium bus duct and Adaptor Box including all accessories at ends.(RYB=1 set)

2000 Amp Ratings Flexible Joint

Supply, erection, testing and commissioning of 2000 Amps Aluminium flexible joints suitable for Sandwich type Aluminium bus duct including all accessories at ends.(RYB=1 set)

HT Cable

Supply, laying, testing and commissioning of 3core 400Sqmm 11KV, XLPE Aluminium conductor individual core screened, flat steel strip armoured, PVC sheathed cable inside the building in the prepared trench

Supply, laying, testing and commissioning of 3core 300Sqmm 11KV, XLPE Aluminium conductor individual core screened, flat steel strip armoured, PVC sheathed cable inside the building in the prepared trench

HT Terminations:

Supply, termination, testing and commissioning of OUTDOOR type termination kit and accessories suitable for 3core 400Sqmm 11KV, XLPE aluminium cable.

Supply, termination, testing and commissioning of INDOOR type termination kit and accessories suitable for 3core 400Sqmm 11KV, XLPE aluminium cable.

Supply, termination, testing and commissioning of INDOOR type termination kit and accessories suitable for 3core 300Sqmm 11KV, XLPE aluminium cable.

LT Cable

LT Cable Details:

Supply and Laying of following size PVC/XLPE (FR-LS) insulated outer sheathed (1100 V grade) copper/aluminium armoured & un armoured conductor cable partly laid in existing cable tray and partly laid in wall/ ceiling with suitable individual clamps at every 1 mtr interval . Cable tray will be measured and paid separately. Cable Tags to be provided at every 50mtr interval and at either side of the bends.Only for Lighting cables cable tie will be permitted other cables clamps to be provided

LT Cables to be laying in hume pipes / directly burried / cable tray. Wherever cable laying in ground the deepth and finishing shallbe as per IS:1255

31/2 core 400 sq.mm. PVC Armoured Aluminium UG Cable

31/2 core 300 sq.mm. PVC Armoured Aluminium UG Cable

31/2 core 240 sq.mm. PVC Armoured Aluminium UG Cable

31/2 core 120 sq.mm. PVC Armoured Aluminium UG Cable

31/2 core 70 sq.mm. PVC Armoured Aluminium UG Cable

4 core 25 sq.mm. XLPE Armoured Aluminium UG Cable

4 core 16 sq.mm. XLPE Armoured Aluminium Cable

4 Core 6 Sq.mm XLPE Copper Armoured Cable

4 Core 4 Sq.mm XLPE Copper Armoured Cable

3 Core 4 Sq.mm XLPE Copper Armoured Cable

3 Core 2.5 Sq.mm PVC Copper Armoured Cable

16 Core 2.5 Sq.mm PVC Copper Armoured Cable

13 Core 2.5 Sq.mm PVC Copper Armoured Cable

8 Core 2.5 Sq.mm PVC Copper Armoured Cable

4 Core 2.5 Sq.mm PVC Copper Armoured Cable

3 Core 1.5 Sq.mm PVC Copper Armoured Cable

LT Cable Termination

Supply, Fixing of Termination kit(Glands & lugs) of the following size cables with suitable double compression glands with suitable crimping socket. The rate shall be inclusive of Gland Earthing Plate Prefabricated as per Gland Size with provision for connecting Cu.SWG and Cable Tags should be engraved type for all I/C,O.G& lighting Circuits (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Cable gland suitable 3 1/2 core 400 sq.mm. PVC Armoured UG Cable

Cable gland suitable 3 1/2 core 300 sq.mm. PVC Armoured UG Cable

Cable gland suitable 3 1/2 core 240 sq.mm. PVC Armoured UG Cable

Cable gland suitable 3 1/2 core 120 sq.mm. PVC Armoured UG Cable

Cable gland suitable 3 1/2 core 70 sq.mm. PVC Armoured UG Cable

Cable gland suitable 4 core 25 sq.mm. PVC Armoured UG Cable

Cable gland suitable 4 core 16 sq.mm. PVC Armoured UG Cable

Cable gland suitable 6 core 4 sq,mm 1.1KV XLPE Copper cable

Cable gland suitable 4 core 4 sq,mm 1.1KV XLPE Copper cable

Cable gland suitable 3 core 4 sq,mm 1.1KV XLPE Copper cable

3 Core 2.5 Sq.mm PVC Copper Armoured Cable

16 Core 2.5 Sq.mm PVC Copper Armoured Cable

13 Core 2.5 Sq.mm PVC Copper Armoured Cable

8 Core 2.5 Sq.mm PVC Copper Armoured Cable

4 Core 2.5 Sq.mm PVC Copper Armoured Cable

3 Core 1.5 Sq.mm PVC Copper Armoured Cable

Distribution Board

SINGLE PHASE DISTRIBUTION BOARD WITH MCBs 4 way / 8 way / 12 way vertical SPMCB sheet steel distribution boards flush type / surface type fitted with bus bars and neutral links with single phase MCB outgoings and separate 2 way provision for accommodating One No. 2 pole incoming MCB / Isolator and another separate 2 way provision for accommodating One No. 2 pole ELCB / RCD with label holder and provisions for taking up cable for size not less than 35 sq.mm

Industrial Type SPMCB DB with IP 54 Protection

12 ways single phase DB No. of ways incomer MCB / Isolator - 2 No. of ways incomer ELCB / RCD - 2 No. of outgoings ways - 10

7 SEGMENTS (3 TIER) 3 PHASE DISTRIBUTION BOARD WITH MCB 4 way / 6 way / 8 way / 12 way TPMCB sheet steel distribution boards flush type / surface type fitted with bus bars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 4 ways in Eachsegment) and separate provisions for MCB / Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder and provisions for taking up cable for size not less than 35 sq.mm.

TPMCB DB with Metal / Acrylic Door Cover with IP 42 Protection

4 ways 3 phase DB No. of ways incomer MCB / Isolator - 4 No. of ways incomer ELCB / RCD - 4 No. of sub-incomers - 12 No. of outgoings ways - 12

Circuit Mains

Supplying, laying, connecting & commissioning 2 Runs of 4 Sq.mm. PVC Insulated stranded copper conductor FRLS wires ( One Eachfor Phase,Neutral) with 1 Run of 2.5 Sq.mm. PVC Insulated multi stranded copper conductor wires for continuous earthing in 2.0 mm. Thick Heavy duty GI Conduits concealed laid in ceiling / wall with necessary clamps, screws etc.,

Supplying, laying, connecting & commissioning 2 Runs of 2.5 Sq.mm. PVC Insulated stranded copper conductor FRLS wires ( One Eachfor Phase,Neutral) with 1 Run of 1.5 Sq.mm. PVC Insulated multi stranded copper conductor wires for continuous earthing in 2.0 mm. Thick Heavy duty GI Conduits concealed laid in ceiling / wall with necessary clamps, screws etc.,

Point wiring

Primary Light Point

Supplying, wiring, connecting and commissioning the light points with 3 Runs of 1.5 Sq. mm. PVC insulated multistranded Copper Conductor wires (One Eachfor Phase, Neutral and (Earth)in 2.0 mm. thick Heavy duty GI Conduits in wall/ ceiling with necessary clamps screws etc.including supplying and fixing 6 AMPS Switch in manufacturers mounting box fixed flush with the wall.The Average length of circuit mains shall be 15.0 Mtrs.

One Light Controlled by one Switch

Secondary Light Point

Supplying, wiring, connecting & commissioning the light points with 3 Runs of 1.5 Sq.mm. PVC insulated multistranded copper Conductor FRLS wires (One Eachfor Phase, Neutral and Earth) in Heavy Duty GI Conduits concealed in wall/ceiling with necessary clamps, screws etc for additional points. The additional points will have to be wired from the first point mentioned under Item under Item No.1 The maximum length will be 5.0 Mts.for Eachadditional point.

Additional Point One Light

Supplying, wiring, connecting & commissioning the light points with High performance microwave occupancy and daylight dimming sensors or equivalent

Supply fixing connecting and commissioning of 6/16A Socket - 3 Module

Supply & Installation of non-metallic industrial receptacle mounted in Polycarbonate enclosure, 20A, 3 Pin socket with 20 A DP MCB suitable for connecting 3C x 4/2.5 sq.mm, Copper. XLPE insulated armoured FR-LS, loop in loop out cable with flame proof socket.(Enclosed with 2 Nos. of earthing terminals)

Supply & Installation of non-metallic industrial receptacle mounted in Polycarbonate enclosure, 32A, 3 Pin socket with 32 A DP MCB suitable for connecting 3C x 4/2.5 sq.mm, Copper. XLPE insulated armoured FR-LS, loop in loop out cable with flame proof socket.(Enclosed with 2 Nos. of earthing terminals)

Supply fixing connecting and commissioning of AC Exhaust Fan 300mm (12") Sweep (Heavy Duty)

Supply fixing connecting and commissioning of Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Project Officer.

Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Project Officer.

Supply and kept in position of Trolley Mounted Water CO2 Stored Pressure Type 50 litres capacity Fire Extinguisher as per IS13385, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Project Officer

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Project Officer

Fire Signages

The following descriptive photo luminescent Green or Red colour safety signages in different sizes / graphics /colours / texts can be made according to the standards accepted by the local Fire service department. The intensity of glow in dark should last not less than 2 hours and the strongest glow shall be produced in the first 30 minutes

Supplay and fixing for Fire extinguisher - with symbol. (Size 150 x 400 mm)

Supplay and fixing for Auto glow exit route maps of size 23.3" x 16.5" with 4mm acrylic sheet at back side and 3 mm a front side with studs

Providing and fixing in position the signages " FIRE ORDER" it should contain the following matter on 3mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyl painted foam board of 3' x 4'.

A) ALERT THE SECURITY AT SECURITY ROOM BY ACTUATING MANUAL CALL POINT LOCATED AT STRATEGIC LOCATIONS.

B) EVACUATE THE OCCUPANTS BY USING FIRE EXITS AND EMERGENCY EXITS ONLY AND ASSEMBLE AT VARIOUS ASSEMBLY POINTS.

C) IF POSSIBLE TRY TO EXTINGUISH THE FIRE BY USING NEAREST / SUITABLE PORTABLE EXTINGUISHER OR WATER FROM NEAREST WET RISER.

D) BE CALM AND DO NOT GIVE ANY ROOM FROM PANIC, WALK, DO NOT RUN.

E) IF YOU ENCOUNTER SERIOUS DIFFICULTY IN EVACUATION, FLAT AND TRY TO ATTRACT ATTENTION OF RESCUE TEAM.

ACTION BY SECURITY/RECEPTION UPON RECEIPT OF INFORMATION THROUGH FIRE ALARM OR FIRE DETECTORS OR BY USING PUBLIC ADDRESS SYSTEM.

A) ALERT THE OCCUPANTS BY USING PUBLIC ADDRESS SYSTEM.

B) INFORM FIRE CONTROL THROUGH ANY ONE OF THE FOLLOWING PHONE NUMBERS: 101 / -------- / -------- / --------.

C) REFER EVACUATION PLAN FROM EVACUATING STANDARD PEOPLE.

D) GUIDE THE FIRE FORCE, ON THEIR ARRIVAL TO THE SEAT OF FIRE.

E) IN CASE OF THE CASUALTIES, CALL AMBULANCE BY DIALLING NUMBER……..

FIRE FIGHTING AGNECY -------------------------------

PHONE : -----------------------

Supply, fixing, testing and commissioning of 1.5TR split Air conditioners suitable for operation on A/C supply single phase 50 Hz 230 Volts with Inverter type and hermetically sealed compressor with air cooled condenser, motor capacitor and start run capacitors, relay and over load protector internal unit, with one indoor and one outdoor unit. The condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube.(High wall chorded/cordless) suitable capacity 3 core sheathed/ PVC copper cable and a battery operated wireless remote unit. 5 star - 1.5 ton capacity ---- etc., complete with all lead & lift, as per specifications and as per directions of the Project Officer of the work.

Light Fittings

Supply fixing connecting and commissioning of 20W 4 Feet LED Fitting with LED

Supply fixing connecting and commissioning of Water Tight Bulk Head Fitting suitable for 100 / 60 Watts Lamp with Guard Heavy Type

LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE)

Supply fixing connecting and commissioning of 60W LED Street Light Fitting with LED

Supply fixing of 40mm dia 1 meter GI pipe arm with suitable clamp for 60W LED Light Fitting.

Cable Tray

Supplying, fabricating, erecting & connecting the following 2.0mm Thickness hot dip GI Laddertype Cable Trays with necessary supports, tees, elbows, bends, bolts and nuts and any other associated accessories to complete the job.

750 X 75 X 2.0 Ladder cable tray

300 X 50 X 2.0 Ladder cable tray

Street Light

Supply, erection, testing and commissioning of 4 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 4000mm Length

Supply, erection, testing and commissioning of 8 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm) 114.30mm OD x 5.40mm Thick x 4500mm Length,88.90mm OD x 4.85mm Thick x 1750mm Length, 76.10mm OD x 3.25mm Thick x 1750mm Length

Supply, erection, testing and commissioning of 10 Metre Length Single Bracket Pole with Base Plate (300 x 300 x 6mm) 139.70mm OD x 4.50mm Thick x 5200mm Length, 114.30mm OD x 4.50mm Thick x 2400mm Length, 88.90mm OD x 3.25mm Thick x 2400mm Length

Supply, erection, testing and commissioning of 10 Metre Length Double Bracket Pole with Base Plate (300 x 300 x 6mm) 139.70mm OD x 4.50mm Thick x 5200mm Length, 114.30mm OD x 4.50mm Thick x 2400mm Length,88.90mm OD x 3.25mm Thick x 2400mm Length

SUPPLY AND ERECTION OF 8M HEIGHT ARCHITECTURAL SINGLE ARM CONICAL POLE 8M height Single arm Conical Pole made in combination of Conical section which is fabricated from High tensile MS Sheet(3mm thick) with top 75mm dia. and bottom 159mm dia. & top Heka Design Bracket which is made of hot dip galvanised mild steel pipe sections 60mm dia.(vertical & horizontal) & MS Rod(14mm dia.) to get 1000mm arm length & pleasing aesthetics. The pole to be provided with a suitable size steel base plate. This mounting steel base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. Entire pole & bracket shall be made to provide pleasing aesthetics as approved by Concerned Project Officer.

After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's partsare painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint- Grey colour

SUPPLY AND ERECTION OF 8M HEIGHT ARCHITECTURAL TWIN ARM CONICAL POLE 8M height Twin arm Conical Pole made in combination of Conical section which is fabricated from High tensile MS Sheet(3mm thick) with top 75mm dia. and bottom 159mm dia. & top Heka Design Bracket which is made of hot dip galvanised mild steel pipe sections 60mm dia.(vertical & horizontal) & MS Rod(14mm dia.) to get 1000mm arm length & pleasing aesthetics. The pole to be provided with a suitable size steel base plate. This mounting steel base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. Entire pole & bracket shall be made to provide pleasing aesthetics as approved by Concerned Project Officer.

After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's partsare painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint- Grey colour

Supply fixing connecting and commissioning of 48W LED Street Light Fitting with LED

Supply fixing connecting and commissioning of 60W LED Street Light Fitting with LED

Supply fixing connecting and commissioning of 120W LED Street Light Fitting with LED

SUPPLY FIXING OF ARCHITECTURAL LED FIXTURE MODEL - LIGHT-PICO NX-( 95W-105W), Power Module LED, 4000K It's body made of Die cast aluminium using pressure die-casting process. Protective Screen in PC(IK08).Hole for coupling on pipes Ø 60 mm, for lateral installation. Pure Polyester Powder Coating in Grey Colour. Silicone gasket enusures the IP protection. IP Rating - IP 66. Height – 87mm,Length-567mm,Width -233mm,Weight – 2.35Kgs.

Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate. Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Estimated LED Lifetime is L70 @ 100,000 hours@Ts 85°C minimum. LM80 report from LED manufacturer should be submitted. The Light fixture shall be in compliance with IEC 60598/IS 10322-Supporting Test Report from UL/UL Authorised/3rd party NABL aboratory should be submitted along with BIS Certificate with manufacturer name same as brand proposed. Light Fixture Sample should be submitted for approval from concerned Project Officer.

Supply fixing connecting and commissioning and of AIO integrated 60W LED solar street light (9000Lm) consist of 150Wp Higher Efficiency Monocrystalline Solar Panels for better performance under low light conditions with 3.2mm Toughened glass cover for durability., 60W LED luminaire with 150 Lm/W, CCT – 5500 -6500 K, CRI > 70, 100% Scratch & UV Resistant Lenses, Corrosion resistant Extruded Aluminium., and with 2DAYS ( 24Hrs ) AUTONOMY 54Ah Lithium Ferro Phosphate (LiFePO4) Batteries for Extremely Safe and Low maintenance, 2000 Cycles and with IP 65 Enclosure for batteries., and CHARGE CONTROLLERS with MPPT Algorithm, Battery Charging Efficiency > 95%, Load Driving Efficiency > 92%. Motion Detection PIR Sensor from Panasonic with Detection Range of upto 12mtrs. In built Protections: Over Charge Protection, Deep Discharge Protection, Battery Reverse Polarity Protection, Load Short Circuit Protection, Load Open Circuit Protection, Reverse Polarity Protection for Panel, Over Temperature Protection. Indications: Charging Indicator (Green Blinking), Low Battery Indicator (Red Blinking), Error Indicator (Both Blinking). COMPLAINCES TO : LM 79 PHOTOMETRIC TEST, IP 65 TEST, IK 07 – IMPACT TEST, MECHANICAL STABILITY DURING WINDS OF 150KMPH. And with EXTRUDED ALUMINIUM FRAME, PRESSURE DIE CAST MOUNTING CLAMP.

Supply fixing connecting and commissioning of Post top lantern fitting with SC holder suitable for 160W Blended Lamp / Incandescent Lamp

Supply fixing connecting and commissioning of LED Flood Light 100W with Integrated Driver

Supplying and Fixing, connecting and commissioning of Bollard light, Light source colour Warm white, Safety class 1 and the light aluminium housing and IP65. colour temperature - 3000K Philips - BCP150PSU

Providing and laying in position 1:2:4 CC (1 Cement 2 Coarse Sand 4 Graded Stone Aggregate 40 mm Nominal size) of 450 x 450x 1000 mm deep, with 32mm GI pipe medium class collar bend for cable entry at the bottom of the foundation i/c grouting of 4 Nos. foundation bolts, including excavation & refilling in RCC Road complete as required as per drawing and specifications attached and with following specifications: (a) Top dia – 75 mm (b) Bottom dia – 125 mm (c) Thickness of sheet – 3mm (Not less than 3mm) (d) Base plate size – 200x200x16mm (e) The pole shall be complete with following:- Set of foundation bolts – 4 Nos., 25mm dia, 750mm in length, and street light spiral earth aluminium and complete with anchor plate. The foundation bolt shall be hot dipped galvanized. (f) Integral junction box duly hot dipped galvanized complete with door and locking arrangement as required.

Supplying and Fixing, connecting and commissioning of street light Sintex Cable junction box IP - 66 with Box Clamp

Supplying and Fixing, connecting and commissioning of hensel grey polycarbonate Cable Terminal box IP - 66

RCC Hume Pipe

providing laying and fixing of following dia RCC Hume Pipe NP2 Class - IS 458/2003 in ground complete with RCC Collers, jointing with cement mortar 1:2 as Project Officer.

300mm dia RCC Hume Pipe

Earthing work

GI Plate Earthing

Supply and installation of earth pipe electrode as per IS 3043 complete with 3mtr long with 40mm dia 'B' class G.I. pipe and GI earth plate of size 600mm x 600mm x 6mm including 2 runs of 65 x 10mm GI flat upto test link from plate earth electrode, watering funnel and necessary bolt, nut and double washer. Including 750mm x 750mm x 3mtr long excavation and construction of 850mm x 850mm x 300 mm high brick wall chamber with cement mortor. The chamber shall be provided with 450mm x 450mm x 10mm cast iron / RCC cover with frame and lockable facility. The plate electrode shall be filled with alternate layer of salt and charcoal as required full depth. The Cover shall be heavy duty to suit heavy vehicle movements

Copper Plate Earthing

Supply and installation of earth pipe electrode as per IS 3043 complete with 3 mtr long with 40mm dia 'B' class G.I. pipe and copper earth plate of size 600mm x 600mm x 3mm including 2 runs of 65 x 10mm CU. flat upto test link from plate earth electrode, watering funnel and necessary bolt, nut and double washer. Including 750mm x 750mm x 3mtr long excavation and construction of 850mm x 850mm x 300 mm high brick wall chamber with cement mortor. The chamber shall be provided with 450mm x 450mm x 10mm cast iron / RCC cover with frame and lockable facility. The plate electrode shall be filled with alternate layer of salt and charcoal as required full depth. The Cover shall be heavy duty to suit heavy vehicle movements

Supplying, laying, connecting & commissioning a of 50 x 10 mm. GI Flat laid in with sleeve necessary clamps, screws, interlinks etc.,

Supplying, laying, connecting & commissioning a of 40 x 10 mm. GI Flat laid in with sleeve necessary clamps, screws, interlinks etc.,

Supplying, laying, connecting & commissioning a of 25 x 3 mm. GI Flat laid in with sleeve necessary clamps, screws, interlinks etc.,

Supplying, laying, connecting & commissioning a of 50 x 6 mm. Copper Flat laid in with sleeve necessary clamps, screws, interlinks etc.,

Supplying, laying, connecting & commissioning a of 40 x 6 mm. Copper Flat laid in with sleeve necessary clamps, screws, interlinks etc., (38)

Supplying, laying, connecting & commissioning a of 25 x 6 mm. Copper Flat laid in with sleeve necessary clamps, screws, interlinks etc.,

Supplying, Erecting, connecting & commissioning a of 6 Sq.mm. PVC Insulated Copper conductor wires in open or concealed fashion enclosed in heavy duty PVC Conduits with necessary clamps, screws, interlinks etc., for EPABX Earthing.

UPS Details

Supply, Installation, Testing and commissioning of 15 KVA UPS system 3 phase input and three phase output and as per the detailed specification enclosed.

Supply, Installation, Testing and Commissioning of Sealed Maintenance Free Batteries to support 15 KVA for 60 minutes complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries.

The vendor shall submit dimensional GA drawing of complete UPS system, battery rack with batteries, Service bypass Panel and Battery bank calculations along with offer.

Supply, Installation, Testing and Commissioning of 63A / 100A 4 Pole MCCB for UPS power

Vertical air terminal

Supply, Installation of Vertical air terminal with accessories: Providing of Air terminals as per IS-IEC -62305 part-3 16mm rod tapered to 10 mm aluminium rod : Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IS/IEC 62305) 1Mtr Air terminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. OBO Type No. 101 VL3000 ( 5401 98 9 ). Accessories : System consist of Fang Fix with base and clamp, on the top air terminal is erected. OBO Type No. F- FIX 16 ( 5403 20 0 ). Fang fix clamp made of SS, lightning tested for 100 KA 10/350 micro sec waveform. 16 KG stone of 365 mm diameter, high level of stability. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked.OBO Type No. F- FIX S16 ( 5403 22 7 )

Down Conductor

Supply, Installation, of and run of 25mm x 6mm GI Flat Down Conductor with necessary clamps / supports on wall / floor / ground for earth connection

Test Link

Supply, Installation, of of Test Link Box for EachDown conductor in order to disconnect the earth termination system to enable measurement of resistance

Supply and laying of class A, 2.0mm thickness 1M X 2M wide chequered rubber mat with dielectric strength of 11KV suitable for 440V installation as per IS 15625 / 2006

Supply of tested hand gloves of 11KV grade.

Supply and providing St.John make first aid box 18SWG MS sheet duly painted as approved by Indian red cross soceity complete with all first aid medicines.

Supply and providing Electrical SLD drawing duly framed with 2mm thick glass in front & 6mm thick ply on backas required

Liasioning Approvals

Towards professional charges for preparation of drawings in necessary formats for approval, follow up and arranging (CEIG) approval of drawings, and arranging power connection. The Rate shall be including preparation and submission of as built drawings of entire installation of the works executed need to be submitted in the blue print of A1 size as required in 4 Sets of hard copy and two set sets of soft copy in CD. The rate shall inclusive of all Machinaries and Equipment's supplied and installed by Other agency also.

Electrical Work

Circuit Mains

Supplying, laying, connecting & commissioning 2 Runs of 4 Sq.mm. PVC Insulated stranded copper conductor FRLS wires ( One Eachfor Phase, Neutral) with 1 Run of 2.5 Sq.mm. PVC Insulated multi stranded copper conductor wires for continuous earthing in 2.0 mm. Thick Heavy duty GI Conduits Open in ceiling / wall with necessary clamps, screws etc.,

Supplying, laying, connecting & commissioning 2 Runs of 2.5 Sq.mm. PVC Insulated stranded copper conductor FRLS wires ( One Eachfor Phase, Neutral) with 1 Run of 1.5 Sq.mm. PVC Insulated multi stranded copper conductor wires for continuous earthing in 2.0 mm. Thick Heavy duty GI Conduits Open in ceiling / wall with necessary clamps, screws etc.,

Point wiring

Supply & Installation of non-metallic industrial receptacle mounted in Polycarbonate enclosure, 63A, 5 Pin socket and 63 A FP RCBO, 100mA suitable for connecting 4C x 25 sq.mm, Al. XLPE insulated armoured FR-LS, loop in loop out cables for maintenance sockets

Light Fittings

150 W High bay light-Storing, fixing, testing and commissioning of the following lighting luminaires including all necessary accessories as per the detailed technical specification enclosed.

Integral LED luminaire with a pressure die cast housing with dedicated optics for optimal light distribution. A specially designed heat management system to ensure luminous efficacy > 80 lm/ W for the system and ensure lumen depreciation upto 30% over 50k burning hours. The luminaire is designed to compliant with relevant immunity, safety and performance and EMI standards. Lumen output at fixture level >14000lumens. (Supply by client)

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Project Officer.

Cable Tray

Supplying, fabricating, erecting & connecting the following 2.0mm Thickness hot dip galvanised Perforated type Cable Trays with necessary supports, tees, elbows, bends, bolts and nuts and any other associated accessories to complete the job.

300 X 50 X 2.0 Perforated cable tray

Plumbing Work

Supplying and fixing Testing and commissioning for White / Colour Special Deluxe Model Glazed Cascade Type Parry ware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Project Officer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover Wall Fitting

Washbasin

Supplying and fixing Testing and commissioning for Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Supplying, fixing Testing and commissioning for CP Two Way Bib Cock with Health Faucet

Internal CPVC Details

Supplying, fixing, testing and commissioning of approved make chlorinated polyvinyl chloride (CPVC) pipes, fittings SDR 11 ASTM CTS, for the following dia, pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Project Officer. Concealed work including cutting chases and making good the wall etc.

20mm Dia CPVC pipe

Supplying, fixing, testing and commissioning of ball valve (brass) of approved quality etc. Complete 20mm Isolation Valve

110mm Pipe

75mm Pipe

50mm Pipe

Supplying, fixing, testing PVC floor trap(multitrap) of 50mm deep water seal with brass CP frame & cover with 75mm dia outlet fixed on a bed of cement concrete 1:3:6 etc., complete.for kitchens/utilities/toilets

Supplying and fixing enclosed type 1000 L water tank specials such as coupler, elbow, bends and Tee,etc This includes jointing of pipes &fittings with solvent cement and cost of cutting chases and making good the same include testing of joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required

Electrical Work

LT Cable

LT Cable Details: Supply and Laying of following size PVC/XLPE (FR-LS) insulated outer sheathed (1100 V grade) copper/aluminium armoured & un armoured conductor cable partly laid in existing cable tray and partly laid in wall/ ceiling with suitable individual clamps at every 1 mtr interval . Cable tray will be measured and paid separately. Cable Tags to be provided at every 50mtr interval and at either side of the bends. Only for Lighting cables cable tie will be permitted other cables clamps to be provided

4 Core 6 Sq.mm XLPE Copper Armoured Cable

3 Core 6 Sq.mm XLPE Copper Armoured Cable

LT Cable Termination

Supply, Fixing of Termination kit(Glands & lugs) of the following size cables with suitable double compression glands with suitable crimping socket. The rate shall be inclusive of Gland Earthing Plate Prefabricated as per Gland Size with provision for connecting Cu.SWG and Cable Tags should be engraved type for all I/C,O.G& lighting Circuits (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Cable gland suitable 4 core 6 sq,mm 1.1KV XLPE Copper cable

Cable gland suitable 3 core 6 sq,mm 1.1KV XLPE Copper cable

Supply fixing connecting and commissioning of Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Project Officer.

Irrigation Water Net Work

Irrigation water supply pumps

Supply, Installation, Testing and commissioning of Irrigation water supply pumps consisting of the following specifications

Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS. M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal, Base Frame: MS. Along with fixed speed control panel Control Panel consisting of the following component: i) A dedicated logic controller control unit c/w preprogramed microprocessor chip ii) Pump monitoring unit to monitor the operation of the pump sets iii)Pressure Transmitter iv)Automatic operation v)Manual and emergency operation vi)Automatic sequence change vii)Set point viii)Frictionloss compensation" ix)Displays x)Pump status and Zone Status xi)Provision for BMS Interface

Technical Parameters :

Irrigation Flow - 20 Cu.M/ Hour at 10 MWC 2HP with fixed speed motor for Eachpump.

No. of Pumps for Irrigation - 2 ( 1 working + 1 standby)

Supplying and installation testing & commissioning of PLC Integration for controlling pumps based on on AI-6, DI-13, & DO-8 Schedule with sensor and suitable current relay for main control valve.

PLC / SCADA System shall have to interface with ICCC. The bidder / contractor shall consider the required hard wired / soft integration communication module along with the PLC / SCADA system

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 80mm diameter.

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 50mm diameter.

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 80mm diameter.

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 80mm diameter"

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 50mm diameter"

Supplying and installation of 80NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying and installation of 50NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying, fixing and testing of 80mm GI Puddle Flange and Flange 10mm thickness, Center plate 6mm thikness, for inlet, outlet, vent and overflow pipes, shown on the drawings etc.

HVAC Water Net Work

HVAC water supply pumps

Supply, Installation, Testing and commissioning of Irrigation water supply pumps consisting of the following specifications

Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS. M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal, Base Frame: MS. Along with fixed speed control panel Control Panel consisting of the following component: i) A dedicated logic controller control unit c/w preprogramed microprocessor chip ii) Pump monitoring unit to monitor the operation of the pump sets iii)Pressure Transmitter iv)Automatic operation v)Manual and emergency operation vi)Automatic sequence change vii)Set point viii)Frictionloss compensation" ix)Displays x)Pump status and Zone Status xi)Provision for BMS Interface

Technical Parameters :

HVAC Flow - 53 Cu.M/ Hour at 10 MWC 5HP with fixed speed motor for Eachpump.

No. of Pumps for HVAC - 2 ( 1 working + 1 standby)

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 125mm diameter.

Supplying and installation of AS PER IS 8329/2000 standard welded DI - K9 double flanged pipes with fittings in all respect, including freight, insurance, loading, unloading, transport to store / site, stacking etc. complete as directed by Project Officer. 100mm diameter.

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 125mm diameter.

Supplying and installation of double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto store, unloading, stacking in all respect etc. Complete. 100mm diameter.

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 125mm diameter

Supplying and installation of ISI mark CI Double flange, reflux valves (non-return valves) of following dia including freight, inspection charges, loading, unloading, transportation, stacking, in all respects etc. complete. Reflux valves as per I.S.5312 Part I (2004) 100mm diameter

Supplying and installation of 100NB Cast Iron Dismantling joint as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .

Supplying, fixing and testing of 125mm GI Puddle Flange and Flange 12mm thickness, Center plate 6mm thikness, for inlet, outlet, vent and overflow pipes, shown on the drawings etc.

Chamber CI Sluice valve

Supply, installation, testing and commissioning of courtyard CI Sluice valve double outlet flanged oblique type 110 mm dia valve in Chamber

PART-7-MISCELLANEOUS ITEMS

Providing, fabricating and fixing M.S. grills work for windows, gates, ladders, rail pipes, Nosing angles, with M.S.lugs in staircase steps etc., made out of M.S rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by theProject Officer

Supply and installation of Aluminium fins 1.7mm thick (colour As approved by Project Officer) including supporting aluminium channels, cleats, flashing, anchor fasteners, all required consumables, transportation, lead, lift, etc complete as per approved design, shop drawings and instructions by project in charge. All fixtures & fasteners of SS316 grade. All exposed substructure aluminium shall be PVDF coated & concealed shall be chromatized. Fin of size: 50mm wide x 350mm deep

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ Sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Project Officer.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/Sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm Eachhaving lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Project Officer but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Project Officer.

Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Project Officer. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up Eachside. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Project Officer.

Providing and fixing post delineators made of ABS round body fitted with 2 Nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Project Officer.

Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing.

Providing & fixing of plaster weld mesh minimum width 150mmwide in one layer over the junction of concrete and brick / block masonry and to other required areas,

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifications and as approved by Project Officer. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give guarantee for the perfomance of SRI and also the durabitity of coating, all complete as per direction of Project Officer.

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm Eachand packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

60 cm equilateral triangle

60 cm circular

60 cm x 60 cm square

75 cm high octagon

Direction and Place Identification signs upto 0.9 Sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 Sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

PVC connection Pipe (Drain Spot) of Dia 160, 4 kg/ sq.cm pressures including testing of joints, cost of jointing materials etc. complete in all respect @ 20m C/C for plot connection with road-side drain

Suppying and fixing of 3.60m high heavy duty aluminium reclining ladder

Supply, Fabrication, Erection, alignment and levels as per approved shop drawing of structural steel work in built up sections comprising of ISMB, ISMC, angle, plates and round bar section etc., for column, truss,MS Door in Gas Bank, Stream Generator Room. Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, shop assembly, transport to erection site, storing, leading to erection site and apply a coat of anti corrosive yellow primer paint of approved make prior to erection. (payment to be made on the basis of standard section weights for net weight erected in position excluding permanent/temporary bolts, rivets etc., Rate should include the cost of permanent bolts, nuts, and washers packing plates as required and approved. And no seperate measurement shall be taken for payment of permanent bolts, nuts, all types of washers and packing plates etc..)

Supplying and grouting of pockets inside the concrete structures using non shrink compensated cementitious grout including making arrangements to fix the MS framework , MS bolts , inserts, etc to required line ,level and position & cleaning the pockets & surface using water to make it free from dirt and dust ,pouring the ready mixed grout in the locations as per manufacturers detail specifications including curing at all levels and locations etc., complete all as directed

Supply & fixing of PVC mould CI Steps for Sump

Providing & erecting Single girder type fully electrically operated 7.5 MT Capacity E.O.T. crane with electrically operated hoist, class II duty, geared travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables from motor to starter panel & other required accessories & tested as per IS Specifications.

Providing and installing R.C.C. pipes in standard lengths of class NP2 and suitable diameter, including all taxes, in all respect including inspection charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988.

Pumps

Non clog submersible pumps - Providing, erecting, testing and commissioning of sewage submersible, Non clog type suitable for working on Air filled Dry type motor, three phase, 50 Hz +/-3%, 415V +/- 10%, AC supply, with 3 core flat copper cable from pump to starter panel with cable end terminations (4) all supports, clamps, pipe fittings alongwith mechanical seal, bearing bush, strainer etc. complete set & following M.O.C: Casing CI, SS CF8M impeller, Bronze: wearing ring & Bearing bush, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor body. The scope shall include all required accessories viz, auotmatic coupling device, guide pipe, chain with shakle, flat submersible cable upto starter panel through suitable size GI pipe (30mtr. 3 core flat copper cable for Eachpump) with necessary electrical connection with the starter panel and as per specification. Solids handling capacity of 80mm. 4330 m3/hr @ 10m head (288 HP)

Knife gate valves - Providing, supplying and jointing in position Double Flanged resilient seaetd motorised Knife gate valves of PN 1.0 MPa pressure rating. Conforming to AWWA C520 / MSS SP 81 having Body with CI IS 210 Gr. FG 260, Seal retainer ring, Knife gate, Fasteners with SS A240 Gr.304, Spindle SS A276 410, inlet seal of EPDM, Gland of Carbon steel, Gland packing PTFE, Spindle nut Brass, Supporting bracket and handwheel of Carbon steel, flange drilling shall be as per IS:1538; including transportation and all taxes complete of following dia.

900mm dia

1600mm dia

Dual plate check valve - Supply and fixing of Cast steel ASTM A 216 Gr.WCB double flanged Dual plate check valve Conforming to API 594 with latest amendments Shaft material shall be SS420/431 and spring shall be spring steel superior grade quality as detailed below of following diameters and types and conveying to work site, loading, unloading, stacking with appurtenances., complete with all lead and lift. The rates are inclusive of cost of Galvanised Bolts and Nuts: For Class 150

900mm dia

Dismantling joint- Providing, supplying, lowering, laying and jointing in position Dismantling joint of following dia including cost of all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete.

900mm dia

Flap gates - Supply, installation, testing and commissioning of Cast iron face wall mounted flap gates of size 1650 (dia.) mm, suitable for upto 2.00 m seating / unseating type water head from Invert level of gate opening including all taxes, insurance, inspection charges, loading, unloading, transportation etc complete.

MS pipes - Manufacturing, providing and supplying spirally welded / ERW/ SAW / fabricated M. S. pipes (Commercial Quality) including procurements of plates, gas cutting to requried size rolling, tack welding assembling in suitable lengths to form pipes, welding on automatic welding machine and forming ‘V’ edge on both ends of pipes including railway freight, insurance, unloading from railway wagon, loading into truck, transport to stores, unloading, stacking excluding GST levied by GOI & GOM in all respect, etc, complete as per IS - 3589 and IS-5504 as applicable as per specifications (No negative tolerance in thickness is permissible).

900mm dia

1800mm dia

HDPE pipes - Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete.

1800mm dia

HDPE fittings

Trash screen - Providing, supplying, erecting, testing and commissioning of Trash screen with bar sizing of 50mm wide x 10mm thick and having 50mm clear gap between screen bar of SS 316 of following sizes.

1.5m (wide) x 1.7m (height) + 0.5m (FB)

1.55m (wide) x 1.7m (height) + 0.5m (FB)

Supplying and installation testing & commissioning of PLC Integration for controlling pumps based on on DI-31, & DO-18 Schedule with sensor and suitable current relay for main control valve.

PLC / SCADA System shall have to interface with ICCC. The bidder / contractor shall consider the required hard wired / soft integration communication module along with the PLC / SCADA system

Supplying and laying of Rubber moulded hydraulic pressed Paver Block Stone 63mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials, laying and Labour charges etc., The Item shall include filling the gaps with crushd stone sand. Base layer of crushed sand stone shall be measured under seperate item.

Supply fabrication and fixing of GI chain link fencing of size 2" x 2" using 10 Gauge Galvanised Iron Wire thick by using ISMC/angle section of 2.40 ht, 0.3m below FFL grouted with M20 grade concrete of size 0.3 x 0.3 x 0.60m at every 1.80m c/c and chain link frame of size made out of size 50 x 50 x 6mm angle all around and 50mm x 6mm flat at centre portion including one coat of primer two coats of enamel painting etc complete

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed. (75mm thick precast slab)

Providing anti skid grooves over kota stone tread flooring

Supplying and fixing in position SFRC manhole covers with frames (Heavy duty) of size 60cm Dia of best approved quality as per standard specification etc., complete compying with standard specifications

Providing & erecting Single girder type fully electrically operated 1 MT Capacity E.O.T. crane with electrically operated hoist, class II duty, geared travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables from motor to starter panel & other required accessories & tested as per IS Specifications.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete

Supply and installation of locker made of 19mm BWR plywood finished with 1mm thick laminate on both sides. Eachlocker size is 450x300x300mm. It consists of necessary hinges with a 25mm round knob lock. This rate shall include all necessary materials, labours, transportation, unloading, etc to finish as per the instruction of Project Officer.

Providing & erecting Single girder type fully electrically operated 1 MT Capacity E.O.T. crane with electrically operated hoist, class II duty, geared travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables from motor to starter panel & other required accessories & tested as per IS Specifications.

Manufacturing, supplying and fixing 50mm Thick Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Supplying and fixing in position SFRC manhole covers with frames (Heavy duty) of size 100cm x 100cm of best approved quality as per standard specification etc., complete compying with standard specifications

Gazebo:Stone Pillar,Stone coping

Stone column: Providing and fixing Sandstone Pillar of size of Gazebo 9660x8365mm as shown in drawing. The clamps with Stainless Steel bolts and nuts to provide above coping for Steel rafters. The bottom of pillar to be fixed inside RCC pedestal with approved adhesive or equivalent and gap around the pillar in RCC pedestal to be filled with cement slurry as per the drawing. The stone pillar to be erected to vertical plumb with zero tolerance. The grooves in stone pillar to be finished neatly as per the drawing. The work includes the cost of Stainless Steel clamps, bolts, nuts, adhesive, finishing, formwork, cutting, curing, cost of all materials, labour, hire charges of machinery, loading and unloading, lead and lift, transportation, etc., complete as per drawing, excluding cost of RCC pedestal, truss rafters and purlins and as per directions of Project Officer complete including cost of all materials scaffolding HOM of machineries with all lead and lifts labour charges as per directions of Project Officer.

Pillar Size:-300x300x3000 mm

Pergola

Pergola: Providing and fixing Sand stone Pillar, beam and Purlin of size of pergola 6150 x3700mm as shown in drawing. The clamps with Stainless Steel bolts and nuts to provide for fixing joints. The bottom of pillar to be fixed inside RCC pedestal with approved adhesive or equivalent and gap around the pillar in RCC pedestal to be filled with cement slurry as per the drawing. The stone pillar to be erected to vertical plumb with zero tolerance. The grooves in stone pillar to be finished neatly as per the drawing. The work includes the cost of Stainless Steel clamps, bolts, nuts, adhesive, finishing, formwork, cutting, curing, cost of all materials, labour, hire charges of machinery, loading and unloading, lead and lift, transportation, etc., complete as per drawing, excluding cost of RCC pedestal, truss rafters and purlins and as per directions of Project Officer complete including cost of all materials scaffolding HOM of machineries with all lead and lifts labour charges as per directions of Project Officer.

Pillar Size:-200 (L)x200(B) x2700(H) mm

Beam Size:- 6450(L) x150 (B)x200(D) mm

Purlin Size:- 3700(L) x150 (B) x200(D) mm

Pathway

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the Project Officer and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly inclusive of shoring, strutting, bailing out water, ramming, curing etc. complete in all respect by the Project Officer.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

PART-8-EXTERNAL SECURITY SYSTEM

Closed Circuit Television System

PTZ Camera

Supplying, Installation, Testing & Commissioning of PTZ Camera Should consist of CMOS, IP based colour camera & IR illuminator in outdoor housing. Should have suitable ruggedized enclosure to protect equipment from environment/natural hazards. Should be able to be fixed on wall, pole, tower and mast. Should have facility to remotely clean the camera lens with fitted wipers/Provision of anti-dust and water resistant coasting. (To be decided by the user department as per their requirement at the time of indent) Ingress protection :IP 66

Image sensor : ½” or larger, progressive scan, CMOS sensor. Pixels : 4k UHD, 8 Mega Pixel (3840 X 2160) or better. Video compression : H. 265 or better Video output : PAL Focus & Iris Control : Automatic with manual override. SNR (signal to noise ratio) : > 45 dB or better. Resolution & Frame rate : minimum 25 frames per second (FPS) for full HD streams. Streams & Resolutions : i. Stream 1 @ 3840X2160 ii. Stream 2 @ 1920 X 1080 iii. Stream 3 @ 1280 X 720 iv. Stream 4 @ 640 X 360 (Choice of streams and resolutions as mentioned above to be decided by the user department as per their requirement at the time of indent) Multi video resolutions: Quadruple/Triple/Dual Streaming (To be decided by the user department as per their requirement at the time of indent). Shutter speed: Max shutter speed should be 1/8000 sec or higher. Minimum illumination: i Colour mode : 0.1 Lux @ 1.55 ii Black & White mode : 0 Lux @ (IR LED on) Image stabilization: Yes

Angular field of view: i Wide: 58.2 (H), 34.4 (V), 65.2 (D) ii Tele : 1.99 (H), 1.13 (V), 2.3 (D) or equivalent/ better. Wide dynamic range (WDR) : 120 dB true with dynamic range Lens type : Motorised vrifocal Optical Zoom - 20x or better Digital Zoom - 8x or better

IR distance : 200 Mtrs or better Video straming : Quad/Triple/Dual Compress stream or better (to be decided by the user department oas per their requirement at the time of indent). Auto exposure : Electronic level control. Pan and Tilt mechanism: High precision motorized Pan and tilt unit with variable speed facility. I. Azimuth (Pan) 360continuous II. Elevation (Tilt) : 0 to 180 continuous. Pan/Tilt Speed “ 1/Sec to180/Sec Preset Speed :225/sec +0.5 accuracy. Presets : Min 256 presets. Sector Blanking : Min 8 Zones. Digital Noise Reduction : Configurable 2 DNR or 3 DNR. Trigger Events : Motion Detection, Alarm in, Tampering, Target Locking and Tracking. Data Rate: 8 Mbps (Max) for H.265 video compression. Edge Storage : To be supplied with 128 Gb micro SD/SDHC/ SDXC, back field NVR on resumption duration 15 Minutes.

Network protocol: Suitable and required network protocol stack to work camera in TCP/IP based Ethernet network environment (as required for system working). Network Connectivity: Ethernet, 10/100/1000 Base-T IP V 4 & IP V6 Compatible. Discovery Interface: OEM interface to detect the camera automatically and configure network settings. Web server : Internal web server operation system required with embedded OS. Security : SSL encryption, multi user authority, IEEE 802.1X, HTTPS, IP filtering.

Image Settings: Configurable exposure, White Balance, Sharpness. Alarm Input/Output (Minimum): 1 Input and 1 Output. Power sopurce (Input Voltage): 24 V AC, PoE (IEEE 802.3bt), 70 Watt (Heater on, IR LED on) Operating temperature: 20 C to +60 C. Operating Humidity : 0% to 90% non condensing. Enclosure Protection: 1K 10 and IP66. Regulatory approval/ certification for offered model : UL/CE/FCC/BIS complied. Human (Min) Detection 500 Mtr Recognition 250 Mtr Identification 125 Mtr Range: Night (Starlit condition : 10-3 Lux) Human (Min) Detection 200 Mtr Recognition 100 Mtr Identification 50 Mtr

Bullet Camera

Supplying, Installation, Testing & Commissioning of high resolution camera for perimeter intrusion detection designed to meet Fence/ Perimeter monitoring with high definition and also for video analytics during day and night. a) Should consist of CMOS, IP based colour camera & IR illuminator in Bullet type housing. b) Should have suitable ruggedized enclosure (Aluminium) to protect equipment from environmental/ natural hazard i.e. Rain, Heat, Dust & Storm. c) Should be able to be fixed on wall, pole, tower and mast. d) Ingress Protection : IP 67 Image Sensor : ½” CMOS or higher. 8.0 Mega Pixel UHD (3070X1723) or better. Video Compression : H. 265 or better. Video Out Put : PAL Focus & Iris manual and Auto. SNR (Signal to Noise ratio) : 40-50 db. Frame rate minimum 30 frames per second (FPS) or better for UHD streams. WDR : True WDR 120 dB or better.

Lens Type : 4.5 -10mm Motorized lens with auto focus and P- Iris. Audio Support with compression G. 711U/G.711A or better. Audio Streaming : Two Way. Electronic Shutter Speed: 1/301/100,000s. Auto Exposer : Automatic with lock facility. Video Streaming: Quad Streams. Technical Specification: (IR illuminator) – Range = 30 Mtr or more. a) Range (Day light condition) Human (Min) Detection 150 mtr Recognition 100 mtr Identification 50 mtr b) Range (No moon condition preferably Starlit condition : 10-3 Lux) Human (Min) Detection 30 mtr Recognition 20 mtr Identification 10 mtr TCP/IP Baesed, 12 VDC/POE, Internal web server, 2DNR/ 3 DNR,Privacy Masking : 08 Zone or more.,1 i/p and 1 o/p Alarm,Security: SSL encryption, multiuser authority, IEEE 802.1X, 1X, HTTPS, Uploading of certificate for encryption at root.,Regulatory approval/Certification : UL, CE & FCC or BIS complied etc. complete as per specification/drawings and as directed by Project Officer. Range: In Day Condition

Industrial type 8-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Ethernet Switch

Industrial Grade PoE+ Switch 8-Port: Supply, Installation, Testing & Commissioning - Industrial Grade PoE+ Switch 8-Port - SITC of Field switch, Industrial Grade Switch, 8x10/100/1000 Base-T PoE/PoE+ ports with power budget upto 240Watts, 2x1G SFP+ uplink ports, should be provided with 2x1G single mode transceivers, as per the technical specifications ( Include Power Supply and FO Module). It shall be complete as per specification/drawings and as directed by Project Officer

LIU for CCTV Camera Supply - LIU suitable for 12 core SM fibre optics cable ,with duplex LC pigtails ,fully loaded, with Modular Jack Panel, - EachCamera External pole Locations. It shall be complete as per specification/drawings and as directed by Project Officer.

Networking Switch (Server Farm Switch)

Supply, Installation, Testing and Commissioning of Networking Switch (Server Farm Switch): Layer 3 Switch, 48 x 1G/10G/25G SFP+ ports and 4 x 40G QSFP+ ports, full advanced Layer 3 features, shall operate in dual redundancy/High Availability (HA) mode, Software Defined Networking (SDN) Support, installed dual redundant hot-swappable power supplies from day 1, complete as required and as per technical specifications

Access Switch

Supply, Installation, Testing and Commissioning of Networking Switch (Access Switch) having 24 Nos. 10/100/1000 Base-T ports, stacking, all ports capable of providing PoE+ as per 802.3at, switch having a PoE power budget of minimum 1440 Watts, additional minimum 4 SFP+ ports, Software Defined Networking (SDN) Support and inclusive of dual redundant hot-swappable power supplies installed from day 1, complete as required and as per technical specifications

Core Switch

Supply, Installation, Testing and Commissioning of Networking Switch (Core Switch): Layer 3 Switch, 48 x 1G/10G/25G SFP+ ports and 4 x 40G QSFP+ ports, full advanced Layer 3 features, shall operate in dual redundancy/High Availability (HA) mode, Software Defined Networking (SDN) Support, installed dual redundant hot-swappable power supplies from day 1, complete as required and as per technical specifications

42U Rack Floor Mounted

Supply, Installation, Testing & Commissioning of 19" wide mounting frame Networking Enclosures of following size and capacity complete with all accessories. Power to the rack mounted equipment shall be provided by way of 6 Nos. of 19” rack mounted power distribution strips, Eachconsisting of minimum 8 Nos. of 5/15A power sockets and Eachinclusive of 20Amps MCB. It shall be inclusive of minimum 16 Nos. of vertical cable managers and 16 Nos. of 19” 1U size horizontal cable managers. The racks/enclosures shall be provided with smart/intelligent PDUs based power supply for reliable switchover of input power supply. The front and rear door shall be a metal door with perforations. It shall be inclusive of termination of earthing for which a separate signal grounding for all the equipment racks, other than electrical or building earthing shall be provided; Eachrack shall have two Copper Bar Earth kits/strips which should be mounted vertically in the rear side of the rack. Racks shall be inclusive of all the necessary mounting accessories and hardware complete as required for a complete installation. 42U, 1000mmW x 1000mmD, floor mounted, 4 x 90cfm fans

42" diagonal, 1024 x 768 pixels LED television (industrial type)

42" diagonal, 1024 x 768 pixels LED television (industrial type) with all mounting bracket, connection card wire, remote control etc as per the specification. The bracket shall be provided with adjustable type from wall for better serviceability.

8-Port CAT6A FTP Shielded Industrial Grade Din Rail Patch Panel

Supply, Installation, Testing & Commissioning of S/FTP CAT6A patch panel pre-fully-loaded with 8 ports in Industrial Grade Din Rail form factor, with universal A/B labelling and 110 connector terminations on rear of panel inclusive of patching / termination of S/FTP CAT6A cables at all 8 ports. It shall be inclusive of all the necessary mounting accessories and hardware complete as required for a complete installation.

S/FTP CAT6A 10Gbps RJ-45 Patch Cords 1Meter

Supply, Installation, Testing & Commissioning of S/FTP CAT6A 10Gbps RJ-45 Patch Cords Solid Conductor of various lengths for IBMS services. It shall be inclusive of all the necessary mounting accessories and hardware complete as required for a complete installation. 1 meter

S/FTP CAT6A 10Gbps RJ-45 Patch Cords 2Meter

Supply, Installation, Testing & Commissioning of S/FTP CAT6A 10Gbps RJ-45 Patch Cords Solid Conductor of various lengths for IBMS services. It shall be inclusive of all the necessary mounting accessories and hardware complete as required for a complete installation. 2 meters

LC-LC duplex fibber optic patch cords of 1 meter

Supply, Installation, Testing & Commissioning of LC-LC duplex fibber optic patch cords of 1 meter, single mode as required for complete installation and complete as per specification/drawings and as directed by Project Officer.

LC-LC duplex fibber optic patch cords of 3 meter

Supply, Installation, Testing & Commissioning of LC-LC duplex fibber optic patch cords of 3 meters, single mode as required for complete installation and complete as per specification/drawings and as directed by Project Officer.

OFC - Joint Closure Box

OFC - Joint Closure Supply Joint Closure - Standard fibber counts: 24f, Universal type i. E. , suitable for all types of cables (ofc, armoured and metal free cables) Resistant to chemical and corrosive atmosphere, Easy re-entry and closing & Perfectly water and air proof, Provides scope for straight/branch joint 2 number of cable entry port & 1 oval port, suitable for cable size upto-12 mm. , IP Rated = IP68. It shall be complete as per specification/drawings and as directed by Project Officer.

Network Management System

Supply, Installation, Testing and Commissioning of Network Management System (NMS): Network Management Tool for Centralised Configuration, Administration, Fault and Performance Monitoring and Virtualisation Management for wired LAN infrastructure complete as required and as per technical specifications.

Cat 6A Cable

S/FTP CAT6A CABLING COMPONENTS Supply, Laying & Termination of specified make S/FTP CAT6A cable in existing/prelaid surface/recessed steel/PVC conduits or pipes or floor raceways or cable trays, but without the cost of steel/PVC conduits or pipes or floor raceways or cable trays. The cable is to be drawn from individual CCTV to the nearest networking rack. It shall be within the scope of contractor to carry out and submit scanner readings for all IOs for meeting the requirements of relevant EIA/TIA standards as per CAT6A cabling requirements. The contractor shall submit a detail IO maps, labelling and doCumentation related to terminations. It shall be inclusive of all the necessary mounting accessories and hardware complete as required for a complete installation.

12 cores OS2 Single mode armoured fibber cable

12 cores OS2 Single mode armoured fibber cable

Supply, Installation, Testing & Commissioning and Laying of fibber optic cable of various capacities to be laid in existing/prelaid conduits/RCC hume pipes/HDPE/DWC/cable trays as applicable. It shall be inclusive of all the necessary mounting accessories and hardware as required for complete installation and complete as per specification/drawings and as directed by Project Officer. 12 cores OS2 Single mode armoured fibber cable, uni-tube, high density polyethylene outer jacket

Video Management Software

as required at site. The system (recording server level) shall have N+N redundancy. Eachbuilding shall be considered as separate CCTV System in terms of Database, VMS Server and Recording Server. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operator role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecure with features such as Digital Signing, General Data Protection ,

HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; seamless integration with integrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall have support for Analytics like Facial recognition, Panic, Loitering, Tracking People, Object Identification Humans/Vehicle, Covered Faces, License plate (LPR/ANPR), Vehicle Counting, Perimeter and Intrusion, Object Tracking, Tampering, unclaimed baggage detection etc. Bidder has to ensure that in case of any server failure there shall be redundancy at all levels i.e. at live viewing, database management, recording and playback i/c termination etc complete as required and as per direction of Project Officer

Note: 1. Item includes all the switching modules required for connectivity to IP network. 2. Minimum Nos. of cameras per server should be 100 Nos. 3. 250 Nos. of camera analytics (for all required analytics mentioned ) license must be configured in VMS Server. The NVMMS shall be complete system including server for satisfactory surveillance operations with all necessary software’s, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items. The NVMMS shall be complete system including server for satisfactory surveillance operations with all necessary software’s, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items

Storage

Supply Installation Testing & Commissioning of Network Storage Manager (NSM) supporting ONVIF Profile S & G, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec, 3D PTZ control and multi-imager/lens camera support, and intelligence events. System proposed shall have scalability of 4 to 64 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF,

Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1 recorder failover and failback automatically or manually to have maximum system uptime and recording continuity i.e. Eachbuilding will have one storage box additional to meet redundancy requirement. NSM shall have Latest Windows/Linux Operating System as recommended by OEM , Minimum 32 GB RAM DDR4, SATA RAID Card, (2) 1GbE RJ45 Ports; (2) 10GBE SFP+ supporting recording throughput of Mbps 600/1000 Mbps for 1 Gb/10 GB, Windows Server 2016 , Dual Power Supply, RAID 6 8 GB NV Cache RAID Controller card, 5-year onsite warranty , 12 HDD Bays & 2M. 2 SSD Slots, Recording bandwidth of 600mbps/1000 Mbps with 1GB/10GB.

The NSM shall be complete system for satisfactory surveillance operations with all necessary software’s, licenses, required PC Hardware, Storage (NAS/SAN as per OEM recommendation) , accessories etc., civil, electrical works & peripheral items, as required as per specification at site of work in line with the Project Officer instructions. Storage must be calculated for 90 days of recording based on 8MP, 30fps on higher native resolution for 1000 Cameras. Minimum usable storage with VBR shall be 750 TB complete as per specification/drawings and as directed by Project Officer.

CCTV Recording Server

System Server shall be as per OEM Specification - minimum requirements are specified below. Supply, installation, testing & commissioning of PC as per following specifications: Server Specification for Access Control Software- Latest Windows/Linux Operating System, Colour Monitor - 22" Flat Panel LCD Monitor RAM - 16 GB DDR2, 667MHz SD RAM Memory - 500 GB HDD Graphic Card - Integrated Intel Graphics Media Accelerator X3100Two(2) PCI-X and Two(2) PCI-Express Expansion Slots 2/4 USB, 2 serial, and 2 VGA Adaptor, CD/DVD ROM.; USB Keyboard and Mouse Dual Channel Internal Ultra320 SCS Integrated RAID-1 with hot-spare Dual Integrated 10/100/1000 Ethernet NICI/O Expansion Option Should be with Anti-virus and Firewall etc complete as required and directions of Project Officer

Supply, Installation, Testing & Commissioning of A4 Size Laser Printer

MS-Pole

Supply & Erection of 5Mtrs long continuously tapered octagonal pole (bolt fixing type) in single section, with single longitudinal weld & hot dip galvanized suitable for the PTZ/Box CCTV installation including providing and laying in position 1:2:4 CC (1 Cement 2 Coarse Sand 4 Graded Stone Aggregate 40 mm Nominal size) of 450 x 450x 1000 mm deep, with 32mm GI pipe medium class collar bend for cable entry at the bottom of the foundation i/c grouting of 4 Nos. foundation bolts, including excavation & refilling in RCC Road complete as required as per drawing and specifications attached and with following specifications: (a) Top dia – 75 mm (b) Bottom dia – 125 mm (c) Thickness of sheet – 3mm (Not less than 3mm) (d) Base plate size – 200x200x16mm (e) The pole shall be complete with following:- Set of foundation bolts – 4 Nos., 25mm dia, 750mm in length, complete with anchor plate. The foundation bolt shall be hot dipped galvanized. (f) Integral junction box duly hot dipped galvanized complete with door and locking arrangement as required.

Supply and laying of the following size HDPE pipes The cost including excavation to a depth of 750mm to 1000mm from existing ground level, plastering's, back filling, ramping the soil, making the surface to match the original surface as required.

50mm HDPE Pipe

200mm HDPE Pipe

Access Control for Boom Barrier

ANPR Camera

Supplying, Installation, Testing & Commissioning of Automatic Number Plate Regconition Camera with Hardware's & Servers

Long Range Access Control Reader

Supply, Installation Design and Commissioning of Long-range readers as per following specification • Reading Distance: Up to 25 feet (7.6 meters) • Frequency Band: 865 to 868 MHz Frequency-hopping technology • Antenna Output: Circular-polarized RF field • Antenna Gain: 4.77dBi • Circular-polarized RF field Communications Interface • Operating Temperature: At 50% duty cycle – -35 to +65 C (-31 to +150 F) At 100% duty cycle – -35 to +45 C (-31 to +115 F) • Operating Humidity: 0% to 95%, non-condensing • CERTIFICATION/COMPLIANCE - ETSI EN 302 208, CE, RoHS It shall be complete as per specification/drawings and as directed by Project Officer.

Access Controller

Supply, Installation Design and Commissioning of 8 reader / 4 Door controller '256 time Zones, 256 access levels Anti-pass back function,Interlock function , Linkage function,Multi-Card Opening function, Remote door opening and closing, 4 auxiliary input may be connected to infrared body detectors, Number of Outputs Multiple Card Holders Capacity : 30000 Log Events Capacity : 100000,Log Events Capacity : 100000 Number of Readers Supported : 2 ( 26-bit Wiegand reader) Types of Readers Supported : 26-bit Wiegand, Enclosure : Powder Coated Aluminium.Recommended Power Supply : 12V DC, 1.5A

Radio Frequency Identification Device Tag

Supply, installation, testing & commissioning of long range Radio Frequency Identification Device Tag (minimum 5mtrs.) with operating frequency 865 to 867 MHz, IP-66 rating, as per EPC Gen 2 standards etc. complete as required and as per direction of Project Officer

Supply, Laying and Termination of following cables/cable trays/cable trunk/conduits complete as per technical specification/drawings and as directed by Project Officer.

8 core 1.5 sq.mm, multi strand, copper conductor, shielded, LSZH Armoured cable with all necessary termination accessories including saddles, glanding, lugs, ferrules, tags etc. (For reader to controller)

4 core 1.5 sq.mm, multi strand, copper conductor, LSZH Armoured cable with all necessary termination accessories including saddles, glanding, lugs, ferrules, tags etc. (For Reader Interface module, I/O Modules to controller communication looping)

IT Hardware & Software for Access Management

Supply, Installation, Testing & Commissioning of client workstation shall comprise of the following minimum hardware: Latest Windows/Linux Operating System, Minimum 12 GB RAM, dedicated graphics card capable of 1920 x 1080-pixel resolution (or better), 24” LED Monitor 2 No’s for one workstation, Minimum 1 TB SATA Hard Disk Drive, DVD+/- RW, Graphics Card , 1000Mbps ethernet; with Mouse, key-board, MS Windows latest licensed OS and Anti-Virus software license for 5 years and all necessary mounting accessories for the client workstation.

Access Control Software

Enterprise version Server software with Time attendance management system as per specification with client version. Supply, installation, testing, and commissioning of Access Control System Server Software consisting of Access Control system, Visitor management with all employee visitor license, Elevator Control, Guard Tour Management , Mantrap, Alarm DoCument, Alarm management, 3 client License, Graphical layout, Card Enrolment, Badge designing. All these along with high end security features consist in single package with an option to integrate with CCTV sub system (License based), VAPT and ISO Certified as per specifications of this tender etc complete as required and directions of Project Officer

Server

Minimum requirement is specified below, bidders shall quote as per OEM's recommendation Latest Windows/Linux Server Grade Operating System, Industry Standard Server Grade Hardware with minimum 2 processors installed, Xeon or higher platform or as per OEM, Server Memory (RAM): 32GB, Network Interface Card (NIC): Dual or compatible pair of NICs, 1 Gbps & 10 Gbps(x2), RAID support, Hot pluggable Hard Disks/arrays, Hot pluggable redundant power supplies installed, Hot pluggable redundant fans installed, Human Interface: 102-key keyboard and a mouse pointing device Graphics Adapter: 32-bit colour or higher, video resolution 1280x768 pixels, 65K colours non-interlaced Windows Media Player Version 12. It shall be complete as per specification/drawings and as directed by Project Officer

Boom Barrier

Supply, installation, testing & Commissioning of 2.5mtr. Length K4 automatic Boom barrier IP-54 for barrier body and IP 66 for control box with operating time of opening and closing as maximum 2 seconds. Boom barrier should be able to operate automatically upon signal from access control server / controller etc. complete as required and as per direction of Project Officer Length 2.5 M Note: All related civil work are included in the rates.

Supply, installation, testing & Commissioning of 1.5mtr. Length K4 automatic Boom barrier IP-54 for barrier body and IP 66 for control box with operating time of opening and closing as maximum 2 seconds. Boom barrier should be able to operate automatically upon signal from access control server / controller etc. complete as required and as per direction of Project Officer Length 1.5 M Note: All related civil work are included in the rates.

Under Vehicle Surveillance System (UVSS)

Supply, Installation, Testing & Commissioning of UVSS System should Produce Undistorted composite Stitched image of vehicle , UVSS Should be an area Scan based system with minimum 20,000 transactions storing capacity with suitable Computer , System Should allow to view previous transactions. Main Cameras : 3MP (minimum)/ High-resolution long-life colour vision system, Auxiliary & license plate cameras having Resolution : HD ( 1280 x 720 pixel) minimum, Identification range: 4-5 meters (minimum), Integrated Led/camera modules, IR & LED lights are required to produce high quality clear image, LED shall be rated for minimum 1,00,000 operating hours, IP68 rated housing for camera & LEDs; Processor: The system should be supplied with PC with Required Hardware and software of min. Intel I7, 3 GHz; RAM: 4 GB.It shall be complete as per specification/drawings and as directed by Project Officer.

Physical Security System

Door Frame Metal detector

Supply, installation, testing & commissioning of door frame metal detector with passing space of size minimum .75 mtr. width & 2mt. Height, IP-55 rating, Battery backup for minimum 8 hours, Minimum 20 zones, stand alone etc. complete as required and as per direction of Project Officer

Xray baggage scanner: (Double Generator)

Supply, installation, testing & commissioning of X-ray baggage scanner AERB Certified with tunnel opening minimum dimensions 600mm x 400mm, conveyor speed minimum 0.2mt. Per second, conveyor load min. 165kg, mim. Baggage scanner should include input and output roller of min 500 mm along with monitors for viewing and detection. Steel penetration minimum 35mm, Duty cycle 100%, as per international standard etc. complete as required and as per direction of Project Officer

Bollards

Supply, installation, testing & Commissioning of Inbuilt hydraulic bollards as per ASTM F2656-07 M-30/Equivalent PAS-68/ DOS K4 crash rating (Individual bollard Physically crash tested from accredited lab from the relevant standard) with Bollard diameter should be minimum 275mm, Bollard height minimum 1000mm, Bollard rising time 5 to 6 seconds, lowering time approx. 2 to 6 seconds, EFO (Emergency Fast Operation) with maximum 2 to 3 seconds, protection class IP IP66 for control box and inbuilt electrical unit. Bollard should be able to operate automatically upon signal from access control server / controller . Bollards to remain in raised position upon power failure etc. complete as required and as per direction of Project Officer Note: All related civil work are included in the rates.

PART-9-LANDSCAPING & GATES

SOFTSCAPE WORKS

Good garden soil

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Rough dressing

Rough dressing the trenched ground including breaking clods.

Fine dressing

Fine dressing of the ground.

Mixing and spreading of good soil and mannure

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of Project Officer (cost of sludge, dump manure and/ or good earth to be paid separately).

Cow dung manure

Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

Grassing

Shrubs, Hedges and groudcover plantation

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water)

Shrubs Plant

Supply and stacking of Shrubs/ Ground-cover species

Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the Project Officer.

Providing and stacking of Nerium oleander (kaner) dwarf of height 30-40cm. in earthen pot of size 20 cm as per direction of the Project Officer.

Providing and stacking of Plumbego capensis well developed with fresh and healthy 30 to 45 cm ht., with bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the Project Officer.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the Project Officer.

Providing and displaying of Dracaena, having ht. 30 cm and above, multibranched, well developed with fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of the Project Officer.

Providing and stacking of Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the Project Officer.

Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the Project Officer.

Tree plantation

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

Holes 90 cm dia, and 90 cm deep

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water)

Supply and stacking of Tree species

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165cm. in big poly bags of size 25 cm as per direction of the Project Officer.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the Project Officer.

Providing and stacking of Tecoma stans of height 90-105 cm. bushy in big size HDPE bag as per direction of the Project Officer.

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the Project Officer.

Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the Project Officer.

Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the Project Officer.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50cm well developed in big HDPE bags as per direction of the Project Officer.

HARDSCAPE

Stone Benches

Supply and fixing of stone bench, colour Beige sand stone of size 1600x450x500mm .The bench will need to be fixed on site using 1:4 cement mortar.

Gazebo

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the Project Officer with an initial lead of 10 mts and initial lift of 2 mts. and including necessary backfilling in layers of not more than 15 cm thick well rammed, watered and consolidated, clearing and levelling the site, etc., complete complying with standard specification.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the Project Officer. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc.complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Footing, Plinth Beam, etc.

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cmx60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre supported by caurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the RCC works etc., complete complying with standard specifications and as directed by the Project Officer.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

BNR INFRASTRUCTURE PROJECTS PVT LTD

Ramalingam Construction Company Pvt Ltd