SPL REPAIR TO TOILET BLOCK AT GIRL AREA, PROVN OF VIEW CUTTER AT AUDITORIUM AT DGNCC CAMP, CERTAIN WORK AT 22-B MANDIR MARG, ADDN/ALTN AT BLDG NO P-27/8 AT ARTY OFFRS MESS AND QTR NO T-4 CASSEL ROAD UNDER GE (EAST) DELHI CANTT-10

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F framed work such as in door frame, door shuters / gate of angel or other section with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings, including hings hold fast of Fe 410-W (Gde E-250 quality) etc complete all as specified.

S & F Mild steel, plain, black sheet 1.60mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S & F 300mm long Mild steel sliding door bolt with haps, stapple ( bolt type ) and fixing clips of sheet, cast of extraded sections and fixing bolts and sliding bolts of extraded sections complete.

S & F Aluminium alloy powder coated standard hollow section for ventilotors as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and as directed.

S & F 125mm size medium weight cold rolled mild steel butt hinges complete all as specified and as directed.

S & F 100mm size stainless steel butt hinges to PVC frames with reqd nos of screws complete all as specified and as directed.

S & F Aluminum Anodised 150mm size barrel tower bolt with complete all as specified and as directed.

S & F 150mm size aluminum adodised handles complete all as specified and as directed.

S & F 150mm size Mild steel oval shape handles complete all as specified and as directed.

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:6 including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

Taking down cement or cement lime plaster , any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces and finished even and faie without using extra cement in any position incl scafolding etc, complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and fair without using extra cement in any position incl scafolding etc, complete all as specified.

M & L for Preparation of newly plastered internal surfaces of walls/ceilings and applying 2mm thick of Birla White/J K White wall care putty, again sand papering to make surfaces smooth and applying Two coats of Oil Bound Distemper over a coat of wall primer, complete all as specified and as directed.

M & L for Preparation of newly plastered external surfaces of walls upto 4 storied buildings and applying 2mm thick Birla White/J K White wall care putty, again sand papering to make surfaces smooth and applyingg Two coats of weather proofing exterior acrylic emulsion paint premium quality on wall surfaces over a coat of wall primer, complete all as specified and as directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match laid over and including 15 mm thick avg screed bed in CM 1:6 and dismantling of existing floor tiles of any description including cement mortar bedding (but not backing ) and rubbish off the premises complete all as specified and directed.

M & L premium quality coloured glazed ceramic tiles in vertical surface 600 x 300 x 7-8 mm thick, such as skirting, dados , etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick screed bed in CM 1:4 and dismantling of existing tiles of any description including cement mortar bedding (but not backing ) and rubbish off the premises complete all as specified and directed.

M & L for 18/20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab over and including 15 mm thick screed bed in CM 1:4 including rounding to edge of granite as per required and including dismantling of existing granite of any description including cement mortar bedding (but not backing ) and rubbish off the premises complete.

Dismantling timber scantlings (Purlins/Rafters) any sec and size, in any position complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed

S & F painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing AC sheet corrugated or semi corrugated as in roof coverings complete all as specified and as directed.

S & F tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including making good to floor all as specified and dirtected.

S & F in reapir 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket and flush pipe etc complete all as specified and directed

S & F Vitreous china wash basin counter oval type size 600x425x195mm, fixed in repairs, under granite slab with all fitting and fixture, complete all as specified and as directed.

S & F in repairs Brass CP basin mixer central hole, for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. KUP-35051BPM, Jaquar-Cat No. KUP-35005BPM, Kohler-Cat No. K-74013IN-4BND-CP, Kohler-Cat No. K-74026IN-4BND-CP.

S & F in repairs Angle valve of CP high pressure screwed for iron pipe and fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F in repairs Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S & F in repairs Angle valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms complete all as specified and as directed.

S & F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S & F in repairs 100mm bore Sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or fixed to wall or in floors complete all as specified and as directed.

S & F in repairs 100mm bore Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S & F in repairs 100mm dia Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S & F in repairs 100mm dia cast iron cowls complete all as specified and as directed.

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

M & L two coat of synthetic enamel paint over one coat of primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

S&F in repairs PVC (SWR) pipes, 110mm dia single socketed, in any length with rubber ring joints, fixed in walls in repairs complete all as specified and as directed.

S & F in repairs PVC (SWR) 110mm bore bends with access door, complete all as specified and directed.

S & F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete (Make: Jaquar/Marc/Kohler)

S & F in repairs 20mm dia Chromium plated towel rail 60cm long fixed to wall including all fittings for fixing complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete.

M & L for form work to soffits of suspended slabs such as roof slabs, floor, slabs landings and stair and similar work not exc. 20 cm thick flat rough to receive plaster all as specified and directed.

M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete.

M & L for mild steel TMT bar 10mm dia and over cut to length,bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M & L for RCC M25 Nominal Mix using 20mm graded agg as in slabs, supported on walls, landings, balconies and in shelves and the like complete all as specified and as directed.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of flooring or in any position including demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid dry in floor/path incl demolition of existing flooring or tiles of any type of any size complete all as specified and as directed.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

M & L for PCC 1:2:4 type B-1 using 20mm graded stone agg as in surface channels complete.

S & F for Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592, complete all as specified and as directed.

Demolition and breaking up drain pipes (SGSW/ AC/RCC) including hunching and benching set in cement mortar for 150mm to 300mm dia pipe, and removal of debris from site and deposited where directed at a distance not exc 1KM from site complete all as specified and as directed.

M & L for 150 mm dia (internal dia) RCC hume pipe class NP -2 laid and and jointed complete with colleres complete laid in trenches and tested complete all as specified and as directed.

M& L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipe 150 mm bore incl forming cradles complte all as specified and directed.

M&L for Plain Cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete including demolition of existing coping all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

M & L Vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 15 mm thick avg screed bed in CM 1:6 and dismantling of existing floor tiles of any description including cement mortar bedding (but not backing ) and rubbish off the premises complete.

M & L Vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile exceeding 0.42 sqm tile not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 15 mm thick avg screed bed in CM 1:6 and dismantling of existing floor tiles of any description including cement mortar bedding (but not backing ) and rubbish off the premises complete all as specified and directed.

Providing and fixing "RAJSHRI" Brand factory made WPC railing combining WPC board/Fancy designer type grating and WPC frame 100% solid WPC (wood polymer composite) railing of required length and of 2' to 2.5' height , comprising of virgin PVC resin of K value 58-60 (Suspension Grade) , Calcium Carbonate and natural fibres (Wood Powders/rice husk//wheat husk) and non toxic additives, made from single extrusion process, WPC foam board with having minimum density 650kg/cbm and WPC frame having minimum density 780kg/cbm manufactured by "RAJSHRI" an ISO 9001-2015 certified Company, having good screw holding capacity (screw withdrawal strength of 2000N (Face) & 1100N (Edge) , Minimum comprising of 50N/mm2, Modules of elasticity 850N/mm2 and resistance of speed of flame of class A category with property of being termite/Borer free water /Moisture proof and fire resistance. For WPC railing WPC jali to be fixed with WPC frame of size 75x50mm with necessary supporting lengths at vertical as well as horizontal at wall frames to be fixed with 3"x3" GI 'L' or SS cleats to support vertical frame lengths including demolition /dismantling of existing RCC jallies with frames complete all as specified and as directed. (Make : Rajshree or equivalent) (Note : The said item shall be fixed for view cutter in any positions as requirement at site)

S & F Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mmx2.1mm, shutter top section 47.62mm x 44.45mmx1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 kg/RM) incl shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete.

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed 15mm thick in CM (1:4) complete all as specified

M&L for Vetrified ceramic tiles dark shed 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed 15mm thick in CM (1:4) complete all as specified

S&F fancy type chromium plated long body Bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule 15mm bore icluding CP wall flange complete (Make : Jaquar/Marc/Kohler)

S&F in fancy type Stop valves cast copper alloy chromium plated screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipes or for unions, 15mm dia of pipe, complete. (Make : Jaquar/Marc/Kohler)

Wall mixer 3 in 1 inlet system with provision of both shower (hand shower and over head shower) complete with suitable long bend pipe connecting leg, CP flange etc., fixed in repairs, complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S&F CP health Faucet with 1.5 mtr long flexible pipe as per approved sample complete all as specified and directed. Make: Jaquar ALD CHR 563 or Equivalnt in Hindware or Cera

S&F in repair Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specifed and directed.

Aluminium anodized grills with 6mm x 5mm aluminium section having square or diamond shap with fixing rails of channels 12-15mm complete all as directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white including connection in drain and in flushing pipe complete including 'P' or 'S' trap complete all as specifed and directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed.

Glazed and Skelton shutters using 2nd class hard wood, 35mm thick open rebated and prepared to receive glass or gauge etc., edges of framing plain and chamfered or fitted with cut or mitered beads for securing glass or gauze, size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square complete all as specified and as directed.

Factory made Flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

300 mm size aluminium alloy anodised sliding door bolt with haps, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

S& F 150 mm Floor Door Stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor

Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples

Preparation of new wooden surfaces and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, with grey pigment cement and pigment set, jointed and pointed in neat cement slurry in floors over screed bed 15mm thick in CM1:6 complete.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in surface channel and drain.

M&L Brick Work with sub class 'B' Brick straight or curved on plan exc 6m mean radius built in CM (1:4) complete.

PCC 1:3:6 type C1 using 20 mm graded trap stone agregate as in coping including weathering, slightly rounded or chemfered angle and throating as directed.

Removing of excavated soil to a distance exc 250 m not exceeding 500m and depositing where directed.

Providing & Fixing of factory made kitchen cupboards (lower and upper unit) made up of 18mm thick HDHMR board (Century/Action Tesa/Kitply) with both side company pasted (any colour) mild and 10mm HDHMR board with white colour on both sides, front shutter/ partitions shall be made of machine cut 18mm MDG board with laminates (merino/century/kitply) duly lipping (edge bending) complete all at the factory with G profile handle of approved colour and soft closing hinge (Hettich/Godrej/IPSA). (Note: No edge bending will be allowed at the site (Measurement shall be of front face only)

S&F Stainless steel basket (plain) of size 370mm x 485mm x 150mm made of min 4mmdia stainless steel wire approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat art No 6121 or equivalent in IPSA/Hettich as approved by Engr-in-Charge).

Stainless steel thali basket of size 370mm x 485mm x 200mm made of min 4mmdia stainless steel wire of approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat part No 6136 or equivalent in IPSA/ Hettich as approved by Engr-in-Charge).

Supply only Stainless steel bottle full out of size 50cmx40cmx16cm in two tier made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20'' length two way extruded MS galvanised over rollers as approved by Engr-in-Charge (Make: Godrej or IPSA/ Hettich as approved by Engr-in-Charge).

S&F Stainless steel Cutlary basket of size 370mm x 485mm x 100mm made of min 4mmdia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat part No 6132, or equivalent in IPSA/ Hettich as approved by Engr-in-Charge).

Soakage Wells excavation in any tyoe of soil, foundation in PCC 1:3:6 walls honey combed masonry with top ring of M25 Concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M 25 /SFRC cover complete filled with brick bats of size. Size 3 mtr dia and 3 meter Effective depth

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws with bent to a curve (of any radius as per required) complete all as specified and as directed.

S & F 2 mm thick fiber glass reinforced translucent corrugated/semi corrugated/plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc and including dismantling of plain or corrugated sheeting any gauge thickness including Nainital or similar pattern as in roof covering, complete all as specified and as directed. complete all as specified

S & F for Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete.

S & F for Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 2mm in vertical and horizontal members and glazed with 5mm thick tinted glass and 12mm thick prelaminated particle board interior grade with laminations on both faces according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement complete.

S & F designer board false ceiling of size 600x600x4mm thick white prelaminated sett embosed reinforced tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction complete.

S & F Full pedestal pattern wash hand basin, size of basin 630mm x 510mm and pedestal of 900mm long ivory colour as approved by GE including fixing waste pipe and chromium plated brass waste fitting complete all as specified and as directed.

S & F Angle valve of CP any colour high pressure screwed for iron pipe and fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F 15mm bore, fancy type CP bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F 20mm dia Chromium plated towel rail 60cm long fixed to wall including all fittings for fixing complete all as specified and directed.

S & F Towel rack of size 600mm x 350mm cast copper alloy chromium plated all as specified and directed.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, complete all as specified and as directed.

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover CP jet spary, health faucet flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed complete all as specified and as directed.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete.

S & F tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Demolition of brick work built in cement mortar including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

M&L for PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregates as in bed blocks for hold fasts complete all as specified and directed

S&F pressed steel frames for door size of frame125 X 60mm with single or double rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats complete all as specified and directed.

S&F 35mm thick flush shutter, solid core construction, with block board core and plywood face panel commercial type on both sides.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed .

S&F mild steel 300 mm long, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F in repair aluminium door seal white/brown coated with PVC brush or PVC flexible door rubber fitted in bottom of door as required at site complete all as specified and directed.

S&F and fabrication of wardrobe/ cup board, kitchen cabinet, shelves etc made up of 18mm HDHMR board (century/action tesa/Kitply) with both side company pasted lamination (any colour) duly lipping (edge bending) on exposed surfaces with soft closing hinges to shutters as required complete.

S&F in repairs stainless steel kitchen sink with draining board made of 1mm thick sheet for kitchen with plug washers wate pipe cast iron canti lever bracket ovre all size overall size 915mmx 460mm bowl size 410 mmx 330 mmx 160mm complete all as specified and directed. Make- Maharaja/Nirali/Prayag

S&F in repair stainless steel kitchen plate rack size 750 x 900x250 mm deep made out of 1mm thick sheet including fitting arrangement complete. Make- Maharaja/Nirali/Prayag

S&F Magnet ball catcher brass body with 8mm dia steel ball of approved qualities complete all as specified

S&F 150mm Brass handle, cast type, polished bright complete all as specified and directed

S&F 65 mm size brass Cup board lock, 4 lever grade I of superior quality all as specified and directed.

S&F in repair vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Supply only waste fitting 32mm dia , CP for WHB with long screwed shunks and nuts complete all as spd and directed

S&F in repair 15mm bore 2 way bib tap chromium plated brass with flange complete all as spd & directed

S&F in repair corner glass shelf 225x225mm radius consisting of 5.5mm thk sheet glass with CP brass brackets with 02 Nos of CP railing in each set complete all as spd

S&F in repair CP brass towel ring round with round flange fixed with screw to wall complete

S&F grating doom 100mm dia of PTMT complete.

Taking down existing celing any type and any description and provn of E-board 4mmthick self design type tiles ceiling on GI Powder coated channel/Tee/Grid of make(Armstrong or equivalent) frame work with the following specification including cutting holes to brick wall built in cement mortar & making good in cm 1:3 of cement concrete 1:2:4 type BO as required :- (a) Plugging to wall around the rooms & supplying & fixing GI Powder coated angle of size 25x25x1.0 mm (b) S&F of 1.60 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling dash free fasterers (c) S&F 25 x25 x1.5mm GI Powder coated tee as in main & cross members at 595mm c/c supported suspenders alongwith adjustable clamp to maintain level . (d) S&F E-board 4mmthick self design type ceiling tiles of size 595mm x 595mm confirming to relevant IS in squares of GI Powder coated Tee with clips made to shape. Shade and pattern of E- board shall be as approved by GE

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps , jambs, pillars, window cills, cooking plateforms,dado/wall and like in 15mm thick cemnet mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M & L for OUT DOOR coloured ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floor Finishing fair and even without using extra cement complete.

Taking down carefully old unserviceable copper/aluminium point wiring in conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, bell ,regulator and socket etc and making good the disturbed surface of wall / floor/ ceiling etc as original complete all as directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit medium grade ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends,including FRLS, PVC insulated unsheathed 1.5 Sqmm multistranded copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing switches/sockets/fan regulator etc , with and including hylem sheet of suitable size and making good surface as original complete all as directed for the following :-

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

S&F for switch piano, flush type single pole, one way 5 Amp complete all as directed.

S&F of Ceiling rose, insulated body, 3 terminal, 240 volts, etc complete all as directed.

S&F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 04 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

S&F in replacement of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

S&F in replacement of isolator 32 Amp, SPN type complete all as directed.

Taking out of 300 mm sweep Exhaust fan metalic body focus and then keeping in safe custudy for re-use all depositing to MES Store Yard . complete all as specified and as directed .

Refixing of exhaust fan 300 mm sweep metalic body type and making all electric connections complete all as specified and as directed.

S&F LED security light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as directed.

S&F in replacement of security light fitting bracket, 1 mtr long made out of galvanized iron pipe of 25 mm dia size light grade bent to shape complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Material and labour in replacement of LT underground cable XLPE insulated, PVC Sheathed armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm 2 core ISI marked including all connections with thimbles of suitable size, complete all as directed.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

M&L for point wiring with single core fire retardant low smoke PVC insulated, unsheathed multi stranded copper conductor of size 1.5 sqmm alongwith 1.5 sqmm earth wire of multi strand copper conductor (with same specification) connected to common earth dolly and drawing through PVC concealed conduit pipe with Modular box covered with modular sheet (cover plate) for mounting switches, sockets or fan regulators etcfor one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.complete all as specified and as directed.

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

All same as per srl item No 157 here-in-before but with 2.5sqmm FRLS copper wire with 2.5sqmm FRLS copper wire as earth wire for socket point on independent board.

S&F modular switch flush type, 6 amps one way,SP,230 volts AC all as directed.

S&F modular socket outlet 6 amps 5 pin 2 module all as directed.

S&F modular socket outlet 6 & 16 amps 6 pin multipurpose combined 2 module all as directed.

S&F modular switch flush type, 16 amps one way,SP,230 volts AC all as directed.

S&F modular Step Fan regulator, 120 watts single module all as directed.

S&F modular switch bell push flush type, 6 amps one way,SP,230 volts AC all as directed.

S&F Bell push piano single pole , 5/6 Amps, 240 volts.

S&F socket two-in-one 3 pin, 5/6 Amp complete all as specified and as directed.

S&F piano type Step fan regulator, 120 watts single module, complete all as specifed and as directed.

Material and labour for replacement of submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm (same specification) as earth wire complete all as directed.

Material and labour for replacement of submain wiring complete with 2 x 10.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 10 sqmm (same specification ) as earth wire complete all as directed.

S&F in replacement LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 20 Watt cool/warm white as per site requirement complete all as specified and as directed.

S&F in replacement LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound 10 Watt , cool/warm white as per site requirement complete all as specified and as directed.

S&F of bell DINGDONG type, 6 Amps, 240 volts, SP all as specified and directed. .

S&F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection SPN 08 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed.

S&F in replacement of Modular AC Socket with 25 Amps SP mini MCB, 230 Volts, 50Hz. In 4 module sheet metal enclosure complete all as specified and as directed.

S&F in replacement of Ventilating fan 250 mm sweep plastic body type including self cousing louver and making all electric connections, complete all as specified and as directed.

S&F of metal body exhaust fan with copper winding 225 mm sweep 230 volt AC with inbilt grill , complete all as specified & directed.

Taking down of fan any type size complete with blades, fan clamp etc and depositing to MES store yard after dismentling blade complete all as specified and as directed.

S&F BLDC (Brushless Direct Current) Ceiling Fan ( energy efficient), 1200 mm suitable for regulator, not less than 6 service value, voltage 220V,having full copper motor winding & ribbed 3 Nos A/M blades with suitable size down rod. The fan shall have BEE 5 star rating and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan complete all as specified and directed.

M & L in replacement for ceiling fan down rod fabricated out of MS pipe medium grade 15 mm dia cut to length as per site requirement duly painted white with synthetic enamel paint over a coat of red oxide primer having through hole and cut of suitable size at both end for fixing ceiling fan and clamp etc complete all as specified and as directed

S&F Geyser 25 litre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners (4No.) for hanging and CP and PVC connection for inlet and outlet upto stop cock, complete including taking down and depositing the old u/s to MES store yard all as specifed and as directed.

SREE BABA TRADERS

M/s Shubh Enterprises

Akhil Enterprises

garnet engineers contractors