Request for Proposal For Selection of Agency for Redevelopment of Khel Parisar Ground with Hockey Field, Athletic Track and Other Outdoor sports with Specialised work, as per Sport Standards under Smart Cities Mission

Civil Work

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed.

Filling by available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth under floors including, watering, ramming consolidating and dressing complete. Moorum/Hard copra

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. Cement concrete grade M-10 (Nominal Mix) with 20 mm maximum size of stone aggregate

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement. including Admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. M-25 grade reinforced cement concrete by using 410 kg. of cement per cum of concrete. All work up to floor 2 level.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire upto floor two level including all wastage etc. complete. Thermo-Mechanically Treated bars. (Grade 550/600)

Making plinth protection 50mm thick of Cement concrete grade M- 10 (Nominal Mix with 20 mm maximum size of stone aggregate) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Centering and shuttering including strutting, propping etc.and removal of form for : Foundations, footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting, propping etc.and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc.and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc.and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound (Dr. Fixit or Equivallent) consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately For the purpose of measurement the entire treated surface will be measured.

Providing and laying autoclaved aerated concrete (AAC) masonary blocks (Size in mm length 400,500,600 Height 200,250,300 width 100,150,200,250) confirming to IS 2185 PART 3 , having compressive strength not less than 3MPa (Grade II), and the block is jointed with ready mix build fast and eco friendly wet mix pre-polymerized/polymer modified adhesive (make such as Kerakoll, Ultratech, Mageicrete, Fairmate, Ball Endura, Letecrete or equivalent) having minimum compressive strength and minimum splitting tensile strength of not less than 5MPa and 0.34 MPa respectively as per ASTM international and ensuring long lasting thermal insulation according to European norms (EN13501-2) suitable for highh performance of external & internal concrete masonary units in superstructure including striking joints, racking out joints faces and scaffolding and all labour etc. complete, the surface of masonary units (AAC- Block) should be slightly wet prior to application of jointing mortar and there is no need to post cure the wall with water.

12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Washed stone grit plaster on exterior walls of height upto 10 M. above level in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square meter, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (Payment for providing grooves shall be made separately).

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing and applying 1.5 mm thick (in two coat) white cement based wall putty of best quality, over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Two or more coats applied @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr/10 sqm.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing Ist quality ceramic glazed wall tiles (300mmx600mm) conforming to IS : 15622 (6 to 7mm thick) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Antiskid endura floor tiles (300mmx300mm), 12 mm thickness with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand ) including grouting the joints with white cement with matching pigments etc. Complete.

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded (wherever required) and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in flooring laid over 20mm thick base of cement mortar 1:4 (1Cement : 4 Sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. Black - Area of slab more than 0.50 sqm

Providing and fixing 16mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of Black colour - Area of slab over 0.50 sqm.

Extra for providing full edge moulding to 16mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer- in- Charge. Granite work.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Other then teak wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters using following hinges. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing factory made UPVC door frame made of UPVC extruded section having an overall dimension as below (tolerance ±1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be mitred and welded of plastic, galvanized brackets and stainless steel screws. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge Extruded section profile size 42x50 mm.

24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides.The styles and rails mitred and joined at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ± 0.1 mm wall thickness.The lock rail made up of 'H' section, a UPVC hollow section of size 100x24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers,complete as per manufacturer's specification and direction of Engineer-in- charge. (For W.C. and bathroom door shutter).

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing PTMT Butt hinges with necessary screws etc. complete. 100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod weighing not less than 53 gms

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm dia

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern.

Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour.weighing not less than 105 gms.

Providing and fixing square-mouth S.W. gully trap grade 'A'‟ complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With Modular Bricks class designation 40. 180 x 150 mm size P type.

Incinerator for Girls-Toilet Construction of Manualy operated fire based incinerator for girls-toilet i.e. (i) Fire and ash collection chamber 0.60 m X 0.60 m , made of calcium silicate bricks, having 12 mm dia steel bars grating @ 10 cm c/c, i/c MS mesh welded on top including 300mm X 450 mm MS openable door of half grill and half MS plate (3mm Thick) (ii) 0.80 m X 0.80 m incinerator chamber made of calcium silicate bricks with R.C.C. top having opening of size 0.40 m X 0.40 m, for stacking of sanitary napkins. (iii) 0.40 m X 0.40 m duct made of 1.6 mm thick MS sheet for dropping napkins from the toilet opening. (iv) 150 mm dia Class 'C' heavy duty MS pipe conforming to IS 3589/1239 for gas emission with cowel, up to 2.10 meter height above terrace level. (v) Opening in wall having MS flap (1.6 mm thick) of size 0.25X0.25 m, finished with granite. etc complete as per standard drawing no. 5313-B-NB4-9919-R1 Dated 21.02.2017 For Ground Floor Building

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 20 mm nominal bore

Providing and placing on at all floor levels high design HDPE (polyethylene) water storage tank (3 layer) ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 15 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes.

Providing laying and jointing following P.V.C. pipes with solvent cement joint for 6,8 and 10 kg/sqcm pressures including testing of joints, cost of jointing material etc. complete in all respect. ( Conform to IS 4985:2000 and IS 7634 (PT-3) 110 mm dia (6 Kg/cm2)

Manufacturing, providing and supplying spirally welded/ERW/SAW/ fabricated M.S. Pipes (Commercial Quality) including procurements of plates, gas cutting to required size rolling, tack welding assembling in suitable lengths to form pipes, welding on automatic welding machine and forming "V" edge on both ends of pipes including all taxes (Central and local), railway freight, insurance unloading from railway wagon, loading in to truck, transport to stores / site unloading, stacking etc, complete as per IS 3589 and IS 5504 as applicable as per specification (No negative tolerance in thickness in permissible)

Providing and fixing uplasticised PVC connection pipe with brass unions 30 cm length 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Providig and Fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped gavanized steel sections (galvanized @ 120 grams/ sqm both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm ade from 0,30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long sapced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fastners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-Sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-In-Charge. 8 mm thick fully perforated calcium silicate board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable cryslalline structure with minimum compressive strength 225 kg/sq cm, bending strength 100 kg/sq cm, of size 595x595 mm, having perforation of dia 10 mm with minimum perforated area 18% with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg/cum backing.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (For Drain Cover by Grating)

Providing and laying 100 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction and of approved size and design/ shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with coarse sand etc. all complete as per the direction of Engineer-in-charge.

Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with on prepared surface, mixing by mix in place method at OMC, and compacting with vibratory roller to achieve the desired density, complete in all respect and as per relevant clauses of section-400. for Grading- II Material

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (height from crown level of the road and bottom of the sign board shall not be less than 1.5 m.) firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing including painting of vertical post as per specification. 80 cm x 60 cm rectangular

Porviding,erecting, testing and commissioning solar street light system on 80 mm heavy duty galvanised iron pipe 6 meter height with 30cm x 30cm x 2mm base plate installed own cement concrete padestal casing complete with solar panel, solar battery with charger,other accessories with control panel in weather proof pole box,solar fitting LED type or CFL type 18 watt to 20 watt (set of 2 nos.)

Brick work with modular bricks of class designation 40 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete from ground level up to plinth level in cement mortar 1:6 (1 cement : 6 coarse sand).

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material etc. and as per relevant clauses of section 300 & 2100 in Soil upto 3 m depth

Providing and laying Plain/Reinforced cement concrete (mixed in concrete mixture) in open foundation including form work shuttering etc. complete as per drawing and technical specifications and as per relevant clauses of sections 1500, 1700 & 2100 with. PCC Grade M15 with 40 mm maximum size of aggregate

Centering and shuttering including strutting, propping etc.and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor two level excluding cost of centering, shuttering, finishing and reinforcement Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate

Underground RCC Water Tank

Providing and supplying of single phase Tullu Pump of 0.5 HP

Sanitary Pad Vending Machine

Dust Bin (Large)

Dust Bin (Small)

Hand Dryer Conformity to IS: 302-2-30: 2007 latest

Precast Drain 300x450 (Including All)

Electrical Work

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 3CX4Sq,mm ( 2 X 4 sq. mm + 1 X 4 sq. mm earth wire)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying of approved make TPN MCB DB Metal Double Door with provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoing inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator ): 6 way (4+18)

Supplying and installing of RCBOs (Residual current circuit breaker with overload and short circuit protection) ISI marked complete as per I.S. standard confirming to IEC:61009-2-1 & IS:12640- 2:2001,240/415V 50 Hz with 10 kA short circuit withstand capacity for earth leakage, overload & short circuit protection including connection in existing enclosure in approved manner as per specification. DP(4 module) 2 pole 63 Amps, 30 mA sensitivity

Supplying of ISI Marked and accepted standard of Miniature Circuit Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle, 10 kA Value AC supply confirming to IS: 8828: 1996, IEC: 60898 :2002 but without enclosures :- a) Single pole (SP) 6 Amp to 32 Amp Rating

SUB HEAD - II : SHOP ELECTRICALS:

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet (near equipment point) and 25 A modular SP MCB, “C” curve (at accessible point) including connections, painting etc. as required.

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 3½ CORE 120 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 3½ CORE 35 Sq.mm(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 16 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 10 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 6 Sq.mm.(XLPE)

Laying of one number PVC insluated and PVC sheated power cable of 1.1kV grade of size not exceeding 25 Sq.mm direct in ground including excavation, sand cushioining, protective covering and refilling the pit etc. as required.

Laying of one number PVC Insulated and PVC sheathed power cable of 1.1.kV grade of size exceeding 120 Sq mm but not exceeding 400 Sq.mm direct in ground including excavation and cushioning protective covering and refilling the pit etc. as required.

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. Gland Size 45mm 3/3½ x 120 Sq.mm, 3½ x 95 Sq.mm 3 x 150 Sq.mm.

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. Gland size 32mm for 2/3, 3½, 4 x 25 Sq.mm OR 2/3, 3½ x 35 Sq.mm OR 2/3 x 50 Sq.mm.

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. Gland size 28mm for 3/4 x 16 Sq.mm

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. Gland Size 22mm suitable for cable 2/3, 3½, 2/4 x 10 Sq.mm or 2x 16 Sq.mm

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. Gland Size 22mm suitable for cable 2,3,3½ & 4 x up to 6 Sq.mm

SUB HEAD - VI: LIGHTNING PROTECTION:

Providing and fixing of lightning conductor finial made of 25mm dia 300mm long G.I. tube having single prong at top with 85 mm dia 6 mm thick G.I. base plate including holes complete as required.

Providing and fixing G.I. tape 20mm X 3mm thick on parapet and surface of wall of lightening conductor as required ( for Horizontal runs )

Providing and fixing G.I. tape 20mm X 3mm thick on parapet and surface of wall of lightening conductor as required ( for Vertical runs )

Providing and fixing " Testing Joint" made by 20mm X 3mm thick G.I. strip 125mm long with 4 Nos of G.I. bolts, Nut, check nuts and spring washers etc. complete as required .

Providing and laying copper tape 32mm X 6mm thick for earth electrode directly in ground as required

Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt ) complete as required.

SUB HEAD - VII: EXTERNAL POWER SUPPLY:

Supply of 11/0.4 kV, 315 KVA to 11/0.4 kV, 630 KVA (Indoor), compartmentalized (indoor) with 11kv/433V with encloser made of electronically Galvanized with all associated switch gear and protection equipments

RMU (SF6 Type) with 3 Isolator + 1 Breaker with all associated switch gear and protection equipments

11 KV Cables: 11k V , 3 Core, 400 Sqmm XLPE UG Cable Using Conventional Laying with Excavation in Soil, Straight Through Jointing Kits HS Type, Cable Termination Kit\ Outdoor /Indoor HS Type, Cable Covering Tiles 250x125x40 mm or 125x125x40 mm, Sand, RCC Hume Pipe, 2000 mm Long, 150mm Dia., Collars for RCC Hume Pipe, GI Pipe, 150 mm Dia for drain crossing, cable raising with Route and Joint indicating stones etc., per relevant IS standard required to complete the work.

Lightning and surge voltage protection: Supply of all earthing/Lightning arrestors equipments as per relevant IS standard and applicable IE rules to complete the work. As required as per design.

Metering System: Supply and erecting metering unit with wireless monitoring, having capabilities of remotely switchable ON /Off, with MPEB approved energy meter, enclosed in an encloser conforming to IP 65 for existing metering points(Feeder) with microprocessor based class 0.2 accuracy energy meter conforming to relevant IS/IEC standard for 11 KV outgoing feeder suitable for interfacing with GPS time synchronisation equipment. Provision for mouting Floor Mounted as well as wall munted. The accuracy class shall be 1 of the metering system with Total Connected Load of 500 kW. The intergration of the system metering system with MPEB shall be part of the vendor.

Earthing with Copper Earth plate 600mm X 600mm X 3mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt) complete as required.

Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt ) complete as required.

Providing and fixing 25mm X 4mm G.I. strip on surface or in recessed/concealed for connection etc. as required.

Supplying and laying 50mm X 6mm G.I. strip at 0.5 metre below ground level / surface as strip earth electrode including jointing etc. as required.

Supplying and laying 6SWG (5.6mm) G.I. wire at 0.5 Metre below ground level as conductor earth electrode including soldering etc. as required.

Supplying and fixing 33/11/0.4 KV enamel coated danger board size 200x250mm with clamp on existing HT/LT structure / poles.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor 3½ CORE ARMOURED 300 Sq.mm.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor 3½ CORE ARMOURED 120 Sq.mm.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor 3½ CORE ARMOURED 95 Sq.mm.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor 3½ CORE ARMOURED 35 Sq.mm.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor ARMOURED 2 Core 6 Sq.mm.

Laying of one number PVC insluated power cable of 1.1.kV grade of size exceeding 25Sq.mm but not exceeding 120 Sq.mm direct in ground including excavation, sand cushioing, protective covering and refilling the pit etc. as required.

Laying of one number PVC insulated and PVC sheathed power cable of 1.1 kV grade of size exceeding 25 Sq.mm but not exceeding 400 Sq mm in the existing RCC/Hume Stoneware/G.I. Pipe as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core 300 sq. mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core 120 sq. mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core 95 sq. mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core 35 sq. mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 core 6 sq. mm.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. a) 150 mm dia

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. a) 300 mm dia

SUB HEAD - VIII : AREA LIGHTING:

Supply, erection, testing and commissioning of Decorative type pole of 4.0 meter height with 30/35 Watt LED post top mounted on top of pole and The pole shall have decorative MS PU painted base pole more than dai 89mm & top 76mm from base plate to top of the pole. The pole average thickness not less than 3mm.The pole shall have M.S base plate of size 300mm x300mm x10mm at bottom with arangement of fixing 4 nos foundation bolts for proper fixing of pole. The pole shall have service window atbottom profile. The pole shall be provided with built in control box for 3core 2.5sq.mm copper conductor cable, MCB control and 2nos of 40mm dia Class B GI pipe for incoming and outgoing cable etc.The Pole shall be coated with PU painted with rust free and with require sutaible items.

Supply, erection, testing and commissioning of Decorative Bollard 10 /11W Warm White in Color suitable for outdoor location. Fixture shall be IP 65 Protected made up of Aluminum with PU Painted Matt Black Finish including stainless steel screw, corrossion & UV resistant coat, including suitable size of CC foundation, grouting bolt, plastering etc as complete as required.

Earthing with G.I. Earth pipe 4.5 Metre long and 40 mm dia with masonary enclosure in cement mortor, cover plate having locking arrangement on the top etc.(but without charcoal or coke and salt) complete as required.

Providing and fixing 6 SWG (5.6mm) G.I. wire on surface or in recessed/concealed for loop earthing as required.

3 M Decorative Light with Pole

SUB HEAD - IX : D G Set:

Supply, Installation, Testing and Commisioning of 120 kVA 415V Prime Rating Radiator Cooled DG Set With Acoustic Enclosure designed at 40Deg C,having Remote Monitoring feature, G3 Governing Class for DG set and Alternator with AREP windings.with 850 Litre In-Built fuel tank, Residential Silencer, cable Termination Box, AMF Panel, Exhaust System, Laying of Power cable with Cable Tray, Factory Testing for 4 Hour, 990 Lit Fuel Tank in addition to in-built Fuel Tank, Electrical Inspector Approval etc.

"B" Monoblock type pumping sets 10 H.P.

OutDoor Field

Construction of Embankment/Sub grade/ earth shoulders, as per clause 305 & its sub-clauses, Where required but with approved materials/soil like morrum CBR value not less then 7% i/c all lead & lifts i/c excavation, cost of watering, compaction and maintenance of surface during construction to ensure shedding & preventing ponding of water (clause 305.3.6) shaping & dressing (clause 305.3.7), finishing etc. complete but excluding scarifying existing granular/bituminous road surface vide clause 305.6.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

EXCAVATION - Excavation to a depth of 6 inches to remove all weeds and grass from its roots, create a slope of 1” in every 10’ in the sub-base on the shorter axis. Extreme care would need to be taken to ensure a correct slope of 1” in every 10’. Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed.

COMPACTION - Compaction of the sub-base will be by 8 – 10 ton roller.

ANTI TERMITE & WEEDECIDE - Carry out anti termite and weedicide on the total area by making 9” deep holes spaced 12” apart and injecting the chemicals and also spraying.

WATER BOUND MACADAM (WBM) - 200 mm thick Lay a 1st layer of 75mm compacted water bound macadam with good earth (not moorum). WBM to be densely compacted by keying and interlocking the stones to ensure no settlement takes place. Lay a 2nd layer of water bound macadam (75mm thick) same as above except the stone size will be smaller.

BITUMINOUS MACADAM - (Bitumen @3.5 % by weight) Lay a 50mm compacted thick Hot Mix asphalt BM course.

ASPHALTIC CONCRETE - (Bitumen @5.0 % by weight) Lay a 25 mm compacted thick Hot Mix A.C. course

SEAL COAT - Seal Coat with stone dust.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 4mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. Cement concrete grade M-10 (Nominal Mix) with 20 mm maximum size of stone aggregate

Basket Ball Flooring

Edge Wall (350 mm height) Laying a 6" retaining wall keeping the top level straight

Drain - Making an open saucer drain at the lower end

Synthetic Acrylic (8 Layers) - ITF Classified Category 1,2,3,4 & 5 In this system we shall apply 1 layer of resurfacer 5 layers of cushion, 2 layers of colorand court markings. This is a cushioned system which makes for comfortable and enjoyable play. The product must be an ITF classidfied product in all the categories i.e. 1,2,3,4&5

Tennis Accessories American designed tennis net post and export quality tournament nets. They are of excellent quality and are used in all the major tournaments in the country - Net

Tennis Accessories American designed tennis net post and export quality tournament nets. They are of excellent quality and are used in all the major tournaments in the country - Net Post

Tennis Accessories American designed tennis net post and export quality tournament nets. They are of excellent quality and are used in all the major tournaments in the country- Water Removing Roller

Basketball Accessory 8” Round pipe 5.2mm (W.T) with 2.2 mtr distance from the board. Plus 25mm back board transparent Acrylic with International Standard die made framecoated die made frame with built in brackets for mounting. Plus Dunking Rim withthree Spring Mechanism.

Volleyball Accessory - Volleyball net with post

Earth work in excavation by mechanical means (Hydaulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, for all lift and lead, including getting out the excavated soil and disposal of surplus excavated soils as directed, within all lead and lift. All kinds of soil.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming , watering, etc. and disposing of surplus excavated soil as directed , within all lead and lift. - All kinds of soil - Pipes, cables etc. exceeding 80mm dia. but not exceeding 450 mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying non-pressure NP2 class (light duty) R.C.C. S & S jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 300 mm dia. R.C.C. pipe

Constructing brick masonry chamber 90x90x100cm inside, brick work in cm 1:4(1cement:4coarse sand) for sluice valve,electrical cable etc with RCC top slab 1:2:4 mix(1cement:2coarse sand:4 graded stone aggregate 20mm nominal size)i/c necessory excavation,foundation concrete 1:5:10((1cement:2coarse sand:4 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3(1cement:3coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

12 mm cement plaster of mix : 1:4 (1 cement : 4 coarse sand)

Neat cement punning

Consolidation of subgrade with power road roller of 8 to 12 tonne capacity to required slope including making good the undulations etc. with earth or quarry spoils etc.and rerolling the subgrade.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per MORTH specifications and directions of Engineer-in-Charge. - With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site,for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per MORTH specifications and directions of Engineer-in-Charge.

Providing and applying tack coat using cold bitumen emulsion including spraying the bitument with mechanically operated spray unit fitted on bitumen with preparing the existing road surface as per specifications: On W.M.M. @ 0.75 kg./sqm.

Providing and applying tack coat using cold bitumen emulsion including spraying the bitument with mechanically operated spray unit fitted on bitumen with preparing the existing road surface as per specifications: On bituminious surface @ 0.5 Kg/sqm

Providing and laying Bituminous macadam on prepared surface with specified graded crushed stone aggregate for profile corrective base/binder course including loading of aggregate with FE loader and hot mixing of stone aggregates and bitumen in hot mix plant, transporting the mixed material by tipper to paver and laying the mixed material with paver finisher fitted with electronic sensing device to the required level and grade and rolling by road roller as per MORTH specifications, to achieve the desired density and compaction, but excluding the cost of primer /tack coat. 50/75mm average compacted thickness with bitumen of 60/70 grade @ 3.5% (percentage by weight of total mix)

Providing and laying Dense bituminous concrete on the prepared surface with specified graded crushed stone aggregate for wearing course including loading of aggregate with FE loader and hot mixing of stone aggregate, filler and bitumen in hot mix plant, transporting the mixed material by tipper to paver and laying the mixed material with paver finisher fitted with electronic sensing device to the required level and grade and rolling by road roller as per MORTH specifications, to achieve the desired density, but excluding the cost of primer / tack coat. 40/50mm compacted thickness with bitumen of grade 60/70 @ 5.5% and lime @ 3% (percentage by weight of total mix)

Providing and laying IAAF Approved Synthetic Athletics Track : Sandwich system with minimum 13 mm thick layer including line marking which complies with class II certificatin from World Athletics. The product should be from American/ European/ Australian origin only.

Construction of RCC Long Jump pit as per IAAF standard and drawings including cost and conveyance of all materials and labour charges to the site to fill the sand in pits and complete finished item as per drawing and as directed by Engineer-in-Charge (Size 10 X 3m X 0.5m)

Polevault boxes with cover

Take off board for long jump and triple jump plus wooden board

Short put rings

Hammer cum Discuss RING

Aluminum Kerbing

Supplying & Installation of FIH approved National category synthetic hockey artificial turf (Full PUR with minimum 13mm height) and laying, jointing and fixing the same on the bituminous sub base with minimum 15mm thick rubberized shock pad layer as per the FIH requirements and the pasting of synthetic grass as per specification of the National category FIH competition including all marking on the surface as per FIH rules and standard etc. as per the FIH requirements complete as per the instructions of the engineer-in-charge.

Supplying and fixing of aluminum goal post of FIH approved drawing and design including all fitting and net.

Providing, laying & jointing in position HDPE pipe conforming to IS:4985:2000 and suitable for the respective working pressures with all fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc. jointing as per manufacturers' instruction, including excavation of trenches, refilling(Earth work includes 450mm of soil cover over the pipe and width of 300mm) HDPE pipe 160mm-10kg/cm2(PE-100)

Providing, laying & jointing in position HDPE pipe conforming to IS:4985:2000 and suitable for the respective working pressures with all fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc. jointing as per manufacturers' instruction, including excavation of trenches, refilling(Earth work includes 450mm of soil cover over the pipe and width of 300mm) HDPE pipe 90mm-10kg/cm2(PE-100)

Providing & Fixing of Pop up Sprinkler with Gear driven mechanism having 2" female inlet, dia of coverage 84.0-92.0 m at 6.0-7.0 bar, capable of delivering discharge 9.08-15.6 lps and trajectory of throw 23°. The Sprinkler shall be available in (5) numerically coded interchangeable nozzle, the sprinkler nozzle assembly shall incorporated diffuser screw facility for radius reduction and shall be suitable for use in extremely saline and/ or dirty water condition, so that sprinkler shall not require secondary filtration of any kind. The sprinkler shall provide both part and continuous forward full circle adjustment from 40°to 360°. Sprinkler shall have minimum 16cm Pop up Stro ke to bring the rotating nozzle in clean environment. It shall be suitable for sports fields like Football, Rugby, Hockey, Cricket, Soccer & Baseball. It should have a feature of special internal rubber folding top, avoids the passage of powder, sand and dirty water around the telescopic pipe.

Providing and fixing of connecting assembly for 2" PGP.

Providing & Fixing of 1 1/4" Two piece Aluminium Quick Coupling Valve (QCV) It has auto close lid made of heavy duty rubber when QCV is not in use. Dubble piece construction,having stainless steel valves as approved by Engineer -in- charge.

Providing & Fixing of 1 1/4" Steel Quick Coupling Valve (QCV) key with handle with 11/4" outlet as approved by Engineer -in-charge.

Providing & Fixing of Metallic Service Saddle 90mm X 1 1/4"

Providing & Fixing of 4" Butterfly Valve for Head Unit. It shall be with integral synthetic rubber lining. It shall be lever operated quarter turn and offers bi- directional smooth operation. The hydraulic body test pressure of the cast iron buffer type Butterfly Valve is 15 bar and hydraulic seat test pressure of the product is 11 bar as approved by Engineer -in-charge.

Providing & Fixing of 2.5" Gun Metal Ball Valve for bypass arrangment. It shall be full bore, two piece design, lever operated, screwed Female BSP parallel threaded of 2.5" dia. as approved by Engineer -in-charge.

Providing and fixing of 4" Foot valve as approved by Engineer -in- charge.

Providing & fixing of Valve box 20" Rectangular Valve Box with cover. The valve boxes shall be high strength, high density polyethylene constructed material. It should be UV stablizer with anti oxidants, resistant to moisture. It should be minimum 12" height and 25" length as approved by Engineer -in- charge.

Providing and fixing of Aluminum pilot Pressure relief valve size 2" along with bypass arrangement, cover & necessary fittings. It shall be adjustable Pressure setting from 22 PSI - 120 PSI for maximize performance. It should be high strength cast Aluminum body, Stainless Steel shaft offer, strength and corrosion resistant. Oil tempered coil spring provides quick response for individual pressure range as approved by Engineer -in- charge.

Providing & fixing of a double acting Continuous Air release valve 2" made of high strength plastic with fiber glass reinforced . The Continuous Air release valve shall be capable of both releasing and admitting air from and into the line during system operation. The working pressure shall be 10 Bars and testing pressure shall be 16 Bars as approved by Engineer -in- charge.

Providing & fixing of disc filter (120 mesh) 50m3/hr having an inlet & two outlets connections of 3", 2 pressure guaze ports of 3/4", a helix made of fibre glass reinforce polyamide at base of disc filter cartridge to create a helical effect in the incoming water, spinning particulate in suspension away from tec filtering element and so minimizing cleanings frequency, 3/4" outlet for flushing at bottom of filter & maximum working pressure of 14 bars.

Providing and fixing of pressure guaze ( glycerine filled), 4" dial ( 0- 10kg/cm2)

Providing & Fixing of 2" BSP Straight flow Solenoid valve with flow control and "pressure regulation unit" which shall be normally closed 24 VAC 50/60 cycle solenoid actuated angle pattern design. The valve pressure rating shall not be less than 10.5 bar. The valve body shall be constructed of high-impact, weather- resistant Nylon Glass Filled with heavy duty diaphragm and stainless steel screws, fasteners and components. The valve shall have manual open/close control (internal bleed) for manual opening and closing of valve without electrically energizing the solenoid, manual bleed can be removed for " tamper proof" operation. The valve shall operate with minimum 24 VAC at 10.5 bar. The valve must open or close in less than 1 minute at 10.5 bar, and less than 30 seconds at 0.7 bar. The valve construction shall provide for all internal parts to be removable from the top of the valve without disturbing the valve installation as approved by Engineer -in- charge.

Providing and fixing of DBR connector It shall be pre filled, low voltage, dry splice, direct bury , waterproof wire connector that protect electrical connection from corrosion, and moisture. Each splice kit contains two wire nuts, water proof, Gel-filled housing and ideal splice organizer.

Providing and fixing of 1.5 sq. mm single core copper conductor cable (live wire) as approved by Engineer -in-charge.

Providing and fixing of 1.5 sq. mm single core copper conductor cable (Common wire) as approved by Engineer -in-charge.

Providing and fixing of 10 sq. mm single core copper conductor cable (Common wire) as approved by Engineer -in-charge.

Providing and fixing conduit pipe 32mm dia as approved by Engineer -in-charge.

Providing and fixing of booster pump capable of 30 HP ,Discharging 13.25 lps at 75mtr head , Non return volve, suction and delivery assembly.

Providing and fixing of control panal 30 HP with ammeter, voltmeter and necessary protection as approved by Engineer -in-charge.

Providing & fixing of (9 Station) Controller having three programs with three start times per program, one minute to 6 hr run times per station, and 7 day calender with odd/even day watering option. The controller having 365 day calender with leap year, indoor model with plug in transformer and optional outdoor case with locking door. It has start times automatically " stack" in case of overlap programming, water budget 0-200% with pump/master valve standard, non volatile memory and battery back-up.

Providing and fixing of water level sensor controller as approved by Engineer -in-charge.

providing and fixing of pump start relay - as approved by Engineer -in-charge.

Providing and fixing of stablizer for controller. as approved by Engineer -in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. Complete : 25 to 40 mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. Complete : 50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

providing and construction of R.C.C. storage tank sumpwell of 55000 liter to 80,000 liter capacity complete incuding all excavation and earth work , disposal of surplus soil to disdance 250 mtr. Atleast or as desired by engineer -in-charge and to his satisfaction. One maintenace hole cover and iron ladder to be provided as per the dirction of the Engineer-in -charge including carriage of materials within all leads and lifts and other incidental.

Bore well 6 inch dia with outer casiing upto a depth of maximum 100m , including 1.5hp submergible motor and panels

CHEST PRESS DOUBLE APPROX DIMENSION: - 2040 x 860 x 1950 mm. MAX USER WEIGHT 120 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also, with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics. BEARING: - Bearings of ISI standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotation. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process - 0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS. PAINT: - All components are PU paint over two coat of apoxy primer are free of edges and excess weld splatter and cleaned apoxy primer to prevent flash rusting before coating. The coating has a super tough finish with maximum exterior durability and will have superior adhesion characteristics.

TWIST STEPPING MACHINE APPROX DIMENSION: - 1500 x 900 x 1950 mm. MAX USER WEIGHT 110 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics. BEARING: - Bearings of ISI standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotation moment and applied weight. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process - 0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS. PAINT: - All components are PU paint over two coats of apoxy primer are free of edges and excess weld splatter and cleaned apoxy primer to prevent flash rusting before coating. The coating has a super tough finish with maximum exterior durability and will have superior adhesion characteristics.

HORSE RIDER APPROX DIMENSION: - 950 x 300 x 1250 mm. MAX USER WEIGHT 110 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics BEARING: - bearings of ISI standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotation moment and applied weight. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process - 0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS. PAINT: - All components are PU paint over two coat of apoxy primer are free of edges and excess weld splatter and cleaned apoxy primer to prevent flash rusting before coating. The coating has a super tough finish with maximum exterior durability and will have superior adhesion characteristics.

SHOULDER PRESS DOUBLE APPROX DIMENSION: - 2040 x 860 x 1950 mm. MAX USER WEIGHT 110 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also, with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics. BEARING: - bearings of ISI standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotation moment and applied weight. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process -0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS.

SQUAT PUSHING APPROX DIMENSION: - 2268 x 634 x 1590 mm. MAX USER WEIGHT 120 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also, with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics. BEARING: - bearings of ISI standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotation moment and applied weight. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process - 0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS PAINT: - All components are PU paint over two coats of apoxy primer are free of edges and excess weld splatter and cleaned apoxy primer to prevent flash rusting before coating. The coating has a super tough finish with maximum exterior durability and will have superior adhesion characteristics.

CYCLE APPROX DIMENSION: - 1150 x 300 x 1250 mm. MAX USER WEIGHT 110 KG. All Structure made up of galvanized pipe maximum ∅ 100 mm to minimum ∅ 25 mm NB, B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components are electrical resistance welded, hot rolled, and high strength steel tubing.it is used in the various parts. also, with API 5 licence/monogram. SUPPORT STRUCTURE: - The handrail manufactured of 25mm & 32mm O.D. galvanized tube B class conforming to IS 1239:2004 P.U coated with the layer thickness of 60 micron. All tubing used to manufacture components shall be an electrical resistance welded, hot rolled, high strength steel tubing with API 5 licence/monogram. PLASTIC PART: - (FRP) A polymer is generally manufactured by step-growth polymerization or addition polymerization. When combined with various agents to enhance or in any way alter the material properties of polymers the result is referred to as a plastic. Composite plastics refer to those types of plastics that result from bonding two or more homogeneous materials with different material properties to derive a final product with certain desired material and mechanical properties. Fiber-reinforced plastics are a category of composite plastics that specifically use fiber materials to mechanically enhance the strength and elasticity of plastics. BEARING: - bearings of isi standards for smooth rolling action. (skf, rbc) these bearings are designed and arranged dynamically to absorb the vertical thrust due to rotational moment and applied weight. WELDING: - We use process according to maintain its material properties and good surface finish. according to the thickness of material. 1. MIG welding process - 0.5 TO 3 MM THICKNESS 2. ARC welding process - 1.5 TO 5 MM THICKNESS. PAINT: - All components are PU paint over two coats of apoxy primer are free of edges and excess weld splatter and cleaned apoxy primer to prevent flash rusting before coating. The coating has a super tough finish with maximum exterior durability and will have superior adhesion characteristics.

Sports Facilities co Pvt Ltd

L R Brothers

Syncotts International