ADDN / ALTN TO BLDG NO T-192, PROVN OF CHAIN LINK FENCING, INTERLOCKING TILING AT BLDG NO P-117 AND PROVISION OF CHANGING ROOM AND LADIES TOILET IN MT YARD AND MTR AND S CAMP (03 JOBS) AT AFS UNDER GE(AF) SAMBRA.

Amount

Taking down chowkats or frames exc 1.5 sqm but not exc 4 Sqm each (without taking of shutters from the frame) complete all as specified and directed

Taking down chowkats or frames not exc 1.5 sqm each (without taking of shutters from the frame) complete all as specified and directed

Demolition of un-reinforced cement concrete in ground floor and pavings exc 15 cm thick (below or above ground level) and removing the debris out of MD land complete all as specified and directed

Dismantling of brickwork and stone / boulder masonry built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Excavation in trenches not exc. 1.50m wide and not exc 1.5 m in depth; for foundation etc.; or for shafts, wells, cesspits, manholes, pier holes not exc 10 sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed

M&F for PCC 1:4:8, type D-2 (using 40mm graded stone aggregates) as in foundations, mass concrete filling, etc., complete all as specified and directed

M&L for for pre-cast cement concrete block masonry with solid blocks type C1, PCC 1:3:6 (using 20mm graded stone aggregates), exc 10cm in width and setting in CM 1:6 complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed

Removing surplus excavated soil to a distance exceeding 250m but not exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed

M&L for 15 mm thick cement plaster on fair face of brick work or concrete surface in CM 1:4 in two coats (5mm setting coat mixed with WPC over 10mm thick backing coat) for wall finished even & smooth without using extra cement complete all as specified and directed. Note:-Water proofing compound shall be measured and paid separately as supply only.

M&L for applying two coats of acrylic emulsion paint of Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on new plastered surfaces of walls complete all as specified and directed

M&L for rendering 15 mm thick on stone masonary surfaces or surface other than fair face of brick work or on one side of lathing for wall in CM 1:6 to be finished even & smooth without using extra cement complete all as specified and directed

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper on walls over a coat of alkali-resistant priming paints over and including 3mm thick wall care putty complete all as specified and directed

M&L for broken stone or boulder hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 150mm thick plain cement concrete 1:4:8, type D2 (using 40mm graded stone aggregates) as in sub base of flooring complete all as specified and directed

M&L for 25mm thick plain cement concrete, type B1, 1:2:4 (using 20mm stone aggregates) as in sub base of floor complete all as specified and directed

M&L for plain cement concrete, 75mm thick, (1:3:6), type C-1, (using 20mm nominal size crushed and graded stone aggregates) for plinth protection including filling of expansion joint with bituminous mixture finished fair and even complete all as specified and directed

M&L for non skid ceramic tiles, coloured, 7 to 8mm thick (square or rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles as in floors laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450mmX350mmX7mm thick as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed

Dismantling floor, hearth / wall tiling including cement mortar bedding (but not backing) and removing tiles & rubbish off the premises complete all as specified and directed

S&F single piece white colour vitreous China floor mounted pedestal pattern wash down water closet with seat cover having PVC/CI 'P' or 'S' type trap element, rimless one piece including all accessoreis complete all as specified and directed. Make:- Cera Cat Part No. S1013217 or equivalent make as specified in list of makes of Particular Specifications

S&F health faucet ABS body with 1mtr SS braided PVC hose pipe complete all as specified and directed. Make:- Cera Cat Part No. S2030104 or equivalent make as specified in list of makes of Particular Specifications

S&F toilet paper holder with flap guard complete all as specified and directed. Make:- Cera Cat Part No. F5003110 or equivalent make as specified in list of makes of Particular Specifications

S&F towel rail 600mm long with fittings complete all as specified and directed. Make:- Cera Cat Part No. F5015103CH or equivalent make as specified in list of makes of Particular Specifications

S&F two way bib cock with wall flange and aerator complete all as specified and directed. Make:- Cera Cat Part No. F1001163 or equivalent make as specified in list of makes of Particular Specifications

S&F wall mixture with bend pipe for shower and wall flange complete all as specified and directed. Make:- Cera Cat Part No. F1017401 or equivalent make as specified in list of makes of Particular Specifications

S&F vitreous China half stall urinal of size 324mmX310mmX420mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement; 40mm bore dia CP finish cast copper alloy waste fitting and waste pipe, urinal spreader complete all as specified and directed. Make:- Cera Cat Part No. S2030104 & F8070201 or equivalent make as specified in list of makes of Particular Specifications

S&F vitreous China wash hand basin, white in colour, counter type oval shaped of size 560mmX470mmX190mm including 32mm bore dia CP finish copper alloy waste fitting/coupling, PVC waste pipe including cutting of granite top and fixing complete all as specified and directed. Make:- Cera Cat Part No. S2030104 & F8050101 or equivalent make as specified in list of makes of Particular Specifications

S&F pillar tap suitable for 15mm dia pipe complete all as specified and directed. Make:- Cera Cat Part No. F1001201 or equivalent make as specified in list of makes of Particular Specifications

S&F over head shower of size 100mm x 100mm, with 200mm long shower arm and wall flange complete all as specified and directed. Make:- Cera Cat Part No. F7020110SS or equivalent make as specified in list of makes of Particular Specifications

S&F angle cock with wlll flange complete all as specified and directed. Make:- Cera Cat Part No. F1001201 or equivalent make as specified in list of makes of Particular Specifications

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs sink cock wall mounted with with long swivel spout and wall flange complete all as specified and directed. Make:- Cera Cat Part No. F1001251 or equivalent make as specified in list of makes of Particular Specifications

S&F wall mounted Sheet glass shelf assembly (corner self) consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L for machine cut Cudappah stone slab (polished) 40mm to 50mm thick fixed to wall including cutting grooves and cutting hole for WHB complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work, (table rubbed and polished) in platform (for counter type WHB) and like in cement mortar (1:4) or pasting over cudappah stone slab including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

Dismantling and breaking up drain pipes (salt glazed ware, AC, reinforced concrete, PVC or Cast iron) set in cement mortar of size 100mm/75mm fixed over wall or in floor including clamps etc., complete all as specified and directed..

S&F PVC SWR pipe 110 mm bore, single socketed in any length with rubber ring joints fixed to walls including suitable size mild steel clamps complete all as specified and directed..

S&F PVC SWR pipe 75 mm bore, single socketed in any length with rubber ring joints,fixed to walls including suitable size mild steel clamps complete all as specified and directed.

S&F 110 mm dia PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed.

S&F 75mm dia PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed..

S&F 110 mm dia PVC (SWR) bend of any radius complete all as specified and directed..

S&F 75 mm dia PVC (SWR) bend of any radius complete all as specified and directed..

S&F 75 mm dia PVC (SWR) bend with oval access door of any radius complete all as specified and directed..

S&F 75mm bore PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement complete all as specified and directed..

S&F 75 mm dia PVC vent cowl complete all as specified and directed..

Taking up or down 15 mm bore GI/PPR/PVC tubing and connections along with fittings such as tees , bends etc fixed to walls and ceilings or laid in floors/ trenches complete all as specified and directed..

Taking up or down 25 bore GI/PPR/PVC tubing and connections along with fittings such as tees , bends etc fixed to walls and ceilings or laid in floors/ trenches complete all as specified and directed.

S&F Unplasticised PVC pipes 25mm dia of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector and fixing to existing pipe complete all as specified and directed.

S&F Unplasticised PVC pipes 15mm dia of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector, etc., complete all as specified and directed..

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/Sqmm, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. Note: Stainless steel butt hinges and necessary S.S screws shall be paid separately

S&F 100 mm long butt hinges stainless steel to door frame with necessary screwing or bolting complete all as specified and directed..

S&F 150 mm long aluminium anodised handle fabricated type complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised sliding door bolt with hasp and stapple bolt type complete all as specified and directed.

S&F door closer hydraulically regulated, cast iron body, designation No 2 universal type suitable for door shutter of 701 to 850mm in width and weight between 36 to 60 Kg including necessary fixing with shutter and door frame complete all as specified and directed.

M&L for steel work in tubular trusses, posts and supporting member for cladding including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St - 240 complete all as specified and as directed.

M&L for MS plates (plain or chequred) channel, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 W (Gde-E-250) Quality - B including fixing with riveting, bolting or welding complete all as specified and directed..

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel, or flat section) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) quality - A complete all as specified and directed..

S&F pre painted galvalume Aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed..

M&L for Mild steel work for wind ties for roof including securing bolts including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide Zinc chromate primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, not exc 10cm in width or girth, when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enemal paint over a coat of red oxide Zinc chromate primer complete all as specified and directed.

M&L for 12mm thick Gypsum board in ceiling as per manufacturer instruction over and including powder coated aluminium snap grid frame work (size of grid 605 x 605mm) supported by hangers 2 to 4 mm dia GI (up to 1200mm length /as per site requirement) adjusting level fixed to roof slab/walls/wooden/steel members by means of ceiling cleats and painting two coats of oil bound distemper over a coat of primer and preparatory work complete all as specified and directed..

S&F Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing complete all as specified and directed..

S&F Anodised aluminium powder coated door shutters, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium powder coated snap beading, screws, handle 2 Nos complete all as specified and directed.

S&F Anodised aluminium powder coated windows and ventilators shutters, side/top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium powder coated snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos), suitable handle (1 No) complete all as specified and directed.

S&F Anodised aluminium grills powder coated of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws @200 centre to centre, including cutting the grills to proper opening size for fixing and operation of handles and fixing fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

S&F figured glass, pin head type 4 mm thick, not exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed.

S&F sheet plain glass 5.5 mm thick, ordinary quality, in squares not exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws or aluminium beading complete all as specified and directed..

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F brass mortice lock, vertical type, size 100mm, 4 levers complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) three layered wall construction hoisting and fixed in position complete all as specified and directed.

S&F Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 25mm bore dia of pipe and fixed (minimum weight 25mm - 455 gms) complete all as specified and directed.

S&F Gun metal, globe valve, with iron wheel head, screwed both ends for 25mm pipe complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper on walls over a coat of alkali-resistant priming paints over 3mm thick wall care putty complete all as specified and directed.

S&F in repairs decorative stainless steel curtain rod 25 mm dia, 1.25mm wall thickness complete all as specified and directed.

S&F stainless steel brackets for fixing of 25mm dia curtain rod to wall and including decorative stops/ rollers/end cap fixed to both ends of 25mm dia stainless steel rod complete all as specified and directed. Note: Each pair inclusive of two numbers of stainless steel brackets and two numbers of decorative stainless steel stops/roller/end cap.

M&L for 100mm thick cement concrete, type D2, 1:4:8 (using 40mm graded stone aggregates) as in sub base under floor complete all as specified and directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drives ways or light traffic parking etc., of required strength thickness and size/shape, made by table vibratory method laid over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of interlocking paver blocks in to the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed..

S&F 17-18mm thick Rajshri Celuka ply or equivalent make of one side prelam/rigidlam and other side plain colour fixed with screws, solvent cement/adhesive to make cup board/ cabinet shutters/drawer front/sides, partitions, shelves etc. including 1mm thick PVC lipping/beading fixed with solvet over edges of ply of required width and colour complete all as specified and directed. Make: Rajshri Plastiwood or equivalent make as specified in list of makes of Particular Specifications

S&F sleek soft hydraulic auto closing 3D (Big bend/middle bend/straight arm type) stainless steel finish hinges openable of 0 or 15 degree crank for cup board/ cabinet shutters (sample available in GE Office) complete all as specified and directed. Make: Hettich, Harrison, Earl Bihari

S&F stainless steel handles 100mm size, D type dotted for cup board, cabinet shutters complete all as specified and directed.

Cutting exising manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1 smooth finished and reforming benching as required complete all as specified and directed..

Excavating in post holes (or similar holes ) each not exc. 0.5 cum getteting out returning filling in and ramming earth or broken rubble mixed with earth round in layers not exc. 25 cm in hard/dense soil complete all as specified and directed.

M&L for plain cement concrete type C2, 1:3:6 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed .

M&L for plain cement concrete type B2, 1:2:4 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed .

M&L for mild steel angle,flat work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for secruing wire mesh etc) including all necessary drilling, bolting or riveting etc conforming to Fe -290-GdeE-165 complete all as specified and directed.

S&F 10 mm dia MS screw bolts (machine made ) with hexqagonal or square heads at one end & screwed the other or screwed both ends ,each screwed end to be fitted with washers & one hexagonal or square nut length of bolt exc 5 cm & n.exc 10 cm long complete all as specified and directed.

Supply only mild steel, galvanised, PVC coated chain link fencing complete all as specified and directed.

Fixing only chain link fencing incl line wires any mesh size & type to any type of standards rails,straining boltsetc including provision of line wire complete all as specified and directed.

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed

M&L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregates) as in coping and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for 20mm thick Granite (of any type) tiles machine cut as in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

M&L for form work to sides of columns, pillars etc with rough finished surfaces of concrete flat complete all as specified and directed

M&L for RCC M-25 Design Mix (using 20mm graded crushed stone aggregates) as in cloumn footings/plinth beams complete all as specified and directed

M&L for RCC M-25 Design Mix (using 20mm gradede crushed stone aggregates) as in columns complete all as specified and directed

M&L for TMT bars for reinforcement 10mm dia and over cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed

M&L for TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F framed work as in doors or gates of angles or other section with gusset plats, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running, rails and guiedes) and hanging; also fastening complete all as specified and directed

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed

M&L for precast cement concerete in 1:2:4, type B1 (using 20mm graded crushed stone aggregates) as in kerb stone finished even &smooth using extra cement including necessary mould/form work and jointed in CM 1:4 struck flush with same mortar complete all as specified and directed

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping ) complete all as specified and directed

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed

M&L for form work to sides and soffits offloor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc., complete all as specified and directed

M&L for mild steel TMT bars of 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete of M-25 Design Mix (using 20mm graded crushed stone aggregates) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

M&L for reinforced cement concrete of M-25 Design Mix (using 20mm graded crushed stone aggregates) for columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete of M-25 Design Mix (using 20mm graded crushed stone aggregates) for beams, cantilevers, bressumm, lintels over 1.5m span complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1, PCC 1:3:6, using 20mm graded stone aggregate, 10cm thick in width and setting in CM 1:4 complete all as specified and directed.

M&L for rendering 5 mm thick on concrete surface in CM 1:3 for ceiling finished even & smooth without using extra cement complete all as specified and directed.

M&L for Anti termite treatment for soil under plinth protection at the rate of 5 ltr of emultion per Square metre surface area complete all as specified and directed.

M&L for Anti termite treatment for soil alongwith external perimeter of building at the rate of 2.25 ltr of emultion per metre of the perimeter wall complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 600mmX300mmX7mm thick as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles laid over and including cement screed bed15mm thick CM(1:4) complete all as specified a directed

M&L for glazed ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces as in skirting, dado, etc., laid over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified and directed.

S&F vitreous China wash down water closet (pedestal pattern), white with P trap (excluding fluhing cistern and flush pipe) including all accessoreis i.e seat cover complete all as specified and directed

S&F vitreous China squatting pan Orissa pattern of size 630mm x 450mm white with integral foot rest (excluding flushing cistern and flush pipe) including lime concrete bedding all round and finished below level of rim of pan to receive the floor complete all as specified and directed

S&F 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including necessary brackets & screws as required complete all as specified and directed.

S&F 15mm bore bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight 15mm-90gms/20mm 125gms).

S&F waste coupling 32mm size full thread wth 80mm height for wash hand basin complete all as specified and directed.

S&F high density polythelene flexible waste pipe, 32 mm dia, suitable for wash hand basin complete all as specified and directed

S&F 15mm bore pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight 15mm-110gms)

S&F Stop valve of PTMT of 15mm any colour high pressure screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight 15mm-90gms/ 20mm-92gms)

S&F PVC SWR pipe 110 mm bore, single socketed in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR pipe 75 mm bore, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) bend with oval access door of any radius complete all as specified and directed.

S&F nipple suitable for HDPE water tank.(Minimum weight 15mm-38gms/20mm?45gms /25mm- 65gm complete all as specified and directed.

S&F 125 mm long butt hinges stainless steel to door frame with necessary screwing or bolting complete all as specified and directed.

S&F 125 mm long aluminium anodised handle fabricated type complete all as specified and directed.

M/L for 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F factory made uPVC white colour glazed ventilator (louver type frame and arrangement for fixing of exaust fan with the uPVC frame) made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and directed (Glass shall be paid separately). Note:- the unit rate quoted by contractor shall includes all connected accessories. net opening will be measured for payment pourpose)

M&L for reinforced concrete pipe of 150mm dia of class NP-2 laid and jointed complete with collars complete all as specified and directed

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded stone aggregates) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of 150mm bore after they are laid and tested complete all as specified and directed .

M&L for plain cement concrete 1:2:4, type B1(using 20mm graded stone aggregates) as in coping including weathering slightly rounded or chamfered angles and throating and including necessary use and waste of form work complete all as specified and directed

M&L for pre-cast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregates) as in cover slab set in cement mortar 1:4 complete all as specified and directed. NOTE: Reinforcement shall be measured and paid separately.

M&L for round bars 12mm for handles dia cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends complete all as specified and directed

Supply only integral water proofing compound complete all as specified and directed

M&L for point wiring for the following with PVC insulated and unsheathed multi standard 1.5 Sqmm FRLSH copper Cable for one light point controlled by one way switch, and wire to be drawn in and including PVC casing capping 20/25 mm width complete with all accessories including metal GI box / MS sheet metal 1.2mm thick switch board or PVC rectangular switch board of suitable size to be fixed on wall respectively including white washing/colour washing/distembering to match the disturbed surfaces including PVC insulated and unsheathed multi standard 1.5 Sqmm FRLS copper cable as earth continuity conductor connected with common earth dolly including taking down existing point wiring complete all as specified and directed:-

One light point controlled by one, one way switch 5 Amp

One socket point on the same board with other switches

All as per Srl item No 144.00 above but one 3 pin socket outlet 15 Amps independent board with cable 4 sqmm size

S&F switch Modular single pole 6 Amps one way switch AC 230V, 50HZ supply complete all as specified and as directed. Make : Cat Part No. 800100 of Indo Aisian ELVIRA/ACWSXXW101 of Havells CRABTREE(Signia) or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F switch Modular single pole 16 Amps one way switch with indicator AC 230V, 50HZ supply complete all as specified and as directed. Make : Cat Part No.800105 of Indo Aisian ELVIRA/ACWSXIW161 of Havells CRABTREE(Signia) or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F Modular socket 5A AC 230V, 50Hz complete all as specified and as directed. Make : Cat Part No. 802800 of Indo Aisian ELVIRA/ACWKPXW063 of Havells CRABTREE(Signia) or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F Modular SOCKET combine 6A/16A multi purpose AC 230CV, 50Hz complete all as specified and as directed. Make : Cat Part No.800122 of Indo Aisian ELVIRA/ACWKCXW163 of Havells CRABTREE(Signia) or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

M&L for ceiling rose surface backelite three terminal 240 volts complete all as specified and directed

S&F in repacement LED lights fitting 1x 20W, 220V, wall mounted LED batten with Aluminum Housing & integrated electronic driver including connecting up with 0.5Sqmm three core flexible copper conductor cable from ceiling rose complete all as specified and as directed. Make:-Cat Part No: LUMILINE+BS20WLED830SPCSSIND of Havells or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F in replacement sub main wiring in PVC casing caping min 25 mm dia with 2 single core 06 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 06 sqmm copper conductor cable connected to common earth dolly complete and including PVC casing caping all as specified and as directed Note:-Two run of 6 sqmm and one run of 6 sqmm will be measured as 1 RM.

S&F in replacement sheet metal enclosure Double Door factory made distribution board 240 volts SPN 8 way, 200 Amps rated bus bar complete all as specified and as directed.

S&F in replacement MCB SPN 6 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

S&F in replacement MCB SP 06 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers including cutting the wall as round shape for exhasut the air all as specified and directed.

M&L for point wiring for the following with stranded FRLSH copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including MODULAR METAL FLUSH BOX ,modular white cover plate any size with support frame any size module complete all as specified and as directed. cover of approved make, for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed:-

One light point controlled by one, one way switch 5 Amp

One socket point on the same board with other switches

One light point controlled socket point on indpendent board

All as per Srl item No.157 above but one 3 pin socket outlet 15 Amps independent board with cable 4 Sqmm size

S&F LED lights fitting 1x 10W, 220V, wall mounted LED batten with Aluminum Housing & integrated electronic driver including connecting up with 0.5Sqmm three core flexible copper conductor cable from ceiling rose complete all as specified and as directed. Make:-Cat Part No: LUMILINE+BS10WLED865SPCSS of Havells make or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metre depth below normal ground level) with top edge of plate at a depth not less than 1.5 mtr below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to galvanized earth wire 04 mm dia with and including bolts, nuts, check nuts and washers of galvanised iron or steel and riveted to earth plate and one end and connecting to main switch board or metallic bodies of HT/LT equipments etc at the other end, GI wire encased in and including 15 mm bore GI light grade pipe with all fittings, from top of electrode to body of equipment fixed with and including flatiron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI light grade and including funnel, wire mesh, copper lugs etc from bottom of earth pit to top of electrode complete with earth pit in PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate and CI cover complete all specified and shown in electrical plate No 03 of SSR Pt-I connecting earth electrode to test point with and including earthing lead including neessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50m, material and labour complete all as specified and as directed by Engineer-in-Charge. (Notes 1. The rate quoted shall be deemed to include for all the above provisions. 2. PCC chamber shall be constructed at least 1.5 m away from the earth electrode and pipe for watering shall be provided in slanting maner) .

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured,electric power cables (heavy duty) 1100Volts grade with stranded aluminium conductor of size 6.0 sqmm, 2 core complete all as specified and directed

S&F ENDURA SUN DOWN energy saving and environmental friendly long life LED street light made of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP66 protection and impact resistance of IK08 LED street light of 35 Watt with sutable size bracket made to shape of 40 mm dia GI pipe medium grade of 1.4 mtr length including MS clamps 25 x 4 mm - 02 Nos with nut bolts washers complete all as specified and directed. Make:- Havells Cat Part No - ENDURASUNDOWNSL35WLED765PASYBOPC of Havells make or any equivalent make as specified in list of makes of Particular Specifications as approved by GE.

RAJENDRA KRISHNA SARAF (BID ID -3374084)

M/S MAHADEV M PATIL (BID ID -3371057)

M/s. N D KALING (BID ID -3373663)

PURVIK CONSTRUCTIONS (BID ID -3374421)

Sadhana Constructions & suppliers (BID ID -3374175)

M/s PRATAP VIJAYSINGHRAO DESAI (BID ID -3372872)

DHAIRYASIL RAMAKANT DESAI (BID ID -3374516)