Special repair to Bldg No TN-231, TN-232 and TN-233 (ORs Line) at Nagrota.

Amount

Schedule 'A' Part-I (B&R Work)

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm each and n. exc. 4.00 sqm each and removing from site, complete all as specified and directed.

M&L for 20-25 mm thick machine cut kota stone flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding & polishing (mirror finish) over and including 20 mm thick screed bed in CM 1:4 and including dismantling of existing tile, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab in skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding & polishing (mirror finish) over and including 15mm thick beding layer in CM 1:4 and including dismantling of existing tile, complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-1, (using 20 mm graded crushed stone aggregate) as in sub base of floor surface finished even and fair to receive top layer, complete all as specified and directed.

S & F Pressed steel door frames of size 125x60mm, factory made, made out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S&F 100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed for PVC door, type C-21, complete all as specified and directed.

S & F 150mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S&F 150mm aluminium handles cast type, complete all as specified and directed

Supply and fixing factory made box type steel window/ventilators including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded, complete all as specified and directed

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality any size and any stype of frame and glazing with oil putty or beading in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

Prepration of new or previously untreated steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4, complete all as specified and directed.

All as per ser item No. 1.17 here in before but except bricks.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels), complete all as specified and directed.

M&L for 50mm thick PCC, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and fair without using extra cement, complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including 3mm thick wall putty, complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying two coats of oil bound distemper over and including 3mm thick wall putty, complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete, 1:2:4, type B-2 ( using 40 mm graded crushed stone aggregate ) as in sub base of flooring/hard standing, complete all as specified and as directed.

M & L for 25mm thick chequered cement concrete tiles set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over and including 20 mm thick screed bed in CM 1:4 and 100 mm thick PCC, 1:2:4, type B2 (using 40 mm graded crushed stone aggregate) sub base, complete all as specified and as directed.

Dismantling of framed trusses n exc 10 m span including vertical post, complete all as specified and as directed.

M&L for mild steel rolled work as in roof trusses ( framed) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing( Beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc. , conforming to grade Fe 410-S, complete all as specified and directed.

S & F prepainted galvatume zluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws as per manufacturer instruction including dismantling of old existing sheet, complete all as specified and directed.

S & F prepainted galvatume zluminium zinc coating GI based semi plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws as per manufacturer instruction including dismantling of old existing sheet, complete all as specified and directed.

M&L for Mild steel work as in wind tie mild steel flat for roof including scecuring bolt, complete all as specified and directed.

GI T Grid system in 600 x 600 mm module which includes providing and fixing wall angle along the perimeter of the room with nylon sleeves and wooden screws at 300 mm centre to center. Suspendeding the main tee of size from the soffit, soffit cleat, rawl plugs and wire rod & leveling spring clip at 1200mm center to center cross tee, interlockined into the pre-cut slots in the main tees at 600 mm centre to center in direction perpendicular to the main tee to make a grid of 600x 1200mm. Finally 1200 mm cross tees are interlocked in the pre cut slots in the 1200mm tees at 1200 mm center to center in direction parallel to the main tee. Cross Tees having length more than 600 mm are to be supported independently. 6 mm thick aquesostic tile square edge of size 595x595 mm shall be placed into the grid size of 600x600mm. (a) Main T-24x32 thickness 0.3 mm and length 3600. (b) Cross T-24x25 thickness 0.3 mm and length 1200. (c) Cross T-24x25 thickness 0.3 mm and length 1600. (d) Wall angle - 24x24 thickness 0.4 mm and length 3000. Make : Gyproc Saint Gabin Gyproc/Everest.

Built in bed side steel locker over all size shall be 760mm long x 600mm wide x 1100mm high, having three shelves and four compartments.Top, sides, back, doors, shelves and base and legs shall be made up of MS Sheet of 1mm thick (nominal) locker shall weigh 49 Kgs. Two Handles shall be 100mm long Chromium plated. Hasp & Staple of size 75mm long to be provided for closing of Shutters. All steel surfaces internally and externally shall be given two coats of synthetic enamel paint over a coat of red oxide after preparation of steel surfaces, wherever feasible painting work shall be done with spray machine and locker shall be fixed in position with four Nos. of mild steel bolts embeded in PCC block in wall all as shown in Drg No. FD-1029 Sheet 1/1, including dismantling existing lockers of any description and size,complete all as specified and as directed.

Schedule 'A' Part-II (Internal Electrification)

Taking down carefully unserviceable aluminium point wiring (light, fan, socket bell or power) complete, (fittings such as switches, ceiling rose lamp holder, regulators, sockets, pendants) stacking at site and keeping in safe custody for taking credit, complete all as specified and directed.

Taking down ceiling fan any sweep, removing blades, cleaning the fan completly for dust and dirt and hanging the same back to its original position including connecting the 3 core flexible copper wire to ceiing rose etc after the completion the point wiring including replacement old unservicable fan hook, rubber pad, nut bolts and washers etc, complete all as specified and directed by Engineer in charge.

Point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;-

One ceiling fan/exhaust fan point controlled by one switch 5Amp

One ceiling fan/exhaust fan point controlled by one switch 5Amp

One socket out let 5Amp controlled by one switch on same board.

One socket out let 5 Amp controlled by one switch on independent board.

All as per item No 2.03 here in before but point wiring with 2.5 sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5 sqmm cable as earth continuity conductor for one 15 Amp socket outlet controlled by one 15 Amp switch on independat board, complete all as specified and directed.

S & F Switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S & F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type, complete all as specified and directed.

S & F Switch socket combination 2 in 1 5 pin 5 /15 Amps flush type, complete all as specified and directed.

S&F Ceiling rose 3 terminal complete PVC/polycarbonate isolated body, complete all as specified and directed.

S & F in repairs Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed

S & F in repairs Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, Cat part No. BLRB DB 118 ( for batten fitting) & Cat part no. BLRB18W CW LED (for LED 18 watt ) of Bajaj or equivalent in approved make, complete all as specified and directed.

S & F in repairs LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S &F Lamp holder PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S & F LED bulb 7 watt , complete all as specified and directed.

S & F in repair Sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S & F MCB SPN 63 Amps, 10 KA, 230 volts 'C' series, complete all as specified and directed.

S & F MCB single pole 6 to 40 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

Supply and laying or fixing 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one meter apart including 4 mm dia suspension GI wire including taking down of existing cable , complete all as specified and as directed by Engr-in-Charge.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - III) Amount of Rs. 77210.00 during AOC Note:- Tenderers shall not quote for this Schedule

M/s R.K. Builder and Engineers

ASHISH CONSTRUCTION COMPANY

Hare krishna engineering const.

M/S MANISHA BUILDERS

BHARTI CONSTRUCTIONS

M/S STAR CONSTRUCTIONS

M/S KARAN SINGH CONTRACTOR