REPAIR AND RECANING OF FURNITURE ISSUED TO OTM AND MD ACCN UNDER GE NORTH DELHI CANTT 10

Amount

CHARPOY G I PIPE PLY TOP/CHARPOY PLY TOP : S&F in repairs to 12mm thick plywood BWR Grade, single piece of approved quality with suitable steel screw and cup washer including removal of damaged plywood, rest all as shown on drg and as directed by Engr-in-Charge. . Drawing No FD-220/MAP or similar

CHARPOY G I PIPE NYLON NEWAR (Drawing No FD-220 or similar).

Removing of unserviceable nylon newar from charpoy GI pipe, tightening of all loose components (i.e. complete charpoy), S&F ply wood of size 1980x900x12mm thick BWR Grade ISI marked of approved make. Plywood should be fixed with suitable numbers of mild steel galvanised iron nuts & bolts alongh with washer. 02 No. MS flat iron of size 40x6mm shall be fixed over long rails with nut and bolt complete duly painted with two coats of synthatic enamel paint over a coat of red oxide primer all as specified and as directed by Engineer-in-charge.

Taking out old damaged & worn out following parts of charpoy GI pipe and replace the same with new part without damaging other parts all as per drg or as directed by Eng-in-charge

LONG RAIL: Made of 32mm dia GI pipe medium grade ISI marked of approved make including both side threading complete all as specified and directed

SHORT RAIL: Cutting the unserviceable portion from existing unserviceable long rail obtained from Sl item 2.03 here-in-before and converting into short rail including threading both side and fixing the same in the existing charpoy frame complete all as directed.

LEGS: Cutting the unserviceable portion from existing unserviceable short rail obtained from Sl item 2.04 here-in-before and converting into legs including threading one side for screwing and other side/bottom of leg should be covered with 4mm thick round MS plate complete all as directed.

S&Fixed in repairs GI Elbow 32 mm dia three way medium grade of approved make suitable for fixing the long rail/short rail/legs rest all as shown on drg and as directed by Engr-in-Charge.

S&F of GI check nut 32mm,6mm dia siutable for fixing long rail and short rail complete all as specified and directed.

CHAIR VERANDAH (Drawing No FD-19(M), FD-256,FD-333, FD-359)

Repair/replacement of broken Leg, each one piece made of MS conduit pipe 16G, 19/20mm dia including welding all as per drg and as directed by Engineer-in-charge.

Welding joints of broken leg of 19/20mm MS tube & other joints as per drg

Hard PVC/Nylon shoes as per drg

Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable cane/plastic newar from seat & back and recaning the seat & back of complete chair with approved 4mm white plastic cane as per matt Pattern all specified on drawing or as directed by Engineer-in-charge.

CHAIR DINING (440MMx430MMx890MM) (Drawing No FD-228/FD-279 or similar)

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 30x55x890 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 30x55x460mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and proving new Teak wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and proving new Teak wood rear rail including drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65 mm including drilling holes at 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair dining with best quality of approved plastic cane 2mm wide, 0.4mm thick and border with 3x0.60 mm cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge.

CHAIR WRITING (535MMx470MMx890MM) (Drawing No FD-202/FD-250/FD-280)

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 55x30x890mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 55x30x660mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new Teak wood back rest of size 50 x 15mm slightly curved made out of 50x35mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm including drilling holes at @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail and providing new Teak wood rear rail of size 30x65mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65mm including drilling holes @ 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest of size 60x25 mm and providing new Teak wood arm rest complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair writing with best quality of approved plastic cane 2mm wide, 0.4mm thick and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge.

CHAIR EASY (Drawing No FD-229 or Similar)

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 55x25 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 50x25mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new Teak wood arm rest of size 65x25x610mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front frame and providing new Teak wood front frame of size 55x25 mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 50x25 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rails and providing new Teak wood rear rails of size 50x25mm complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 2mm wide, 0.4mm thick cane and border with 3x0.60 mm cane complete all as specified on drawing or as directed by Engineer-in-charge.

COMMON FOR CHAIR DINING/WRITING :Removing the existing unserviceable stiffeners and providing new Teak wood stiffeners of size 25x20 mm complete all as specified on drawing or as directed by Engineer-in-charge. Drawing No FD-228/ 279/280 or similar

Removing of existing unserviceable/broken PVC Shoes from chairs, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg in the chair dining, chair writing & chair easy as specified & directed by Engr-in-charge. Drawing No FD-228/229/279/280 or similar

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. for the following furniture articles:-

Chair dining, FD-228/279 or Similar

Chair Easy, FD-229 or Similar

Chair Writing, FD-280 or Similar

Anand Construction

NAVEEN TRADERS

SUNIL TRADERS

SMS Enterprises