Loading
Loading…
Loading…
Tender Value
₹4.0 Cr
EMD Value
₹8.0 L
Closing Date
24 Aug 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
+ Capital Works)
S AND T
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB of SGCC, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender (b)(i) In case of composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. Note: Separate completed works of minimum required values for each component shall also be considered for fulfilment of technical eligibility criteria. (b) (ii) In such cases, what constitutes a component in a composite work shall be clearly predefined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (iii) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. The similar single work means: Any Indoor or combined indoor/outdoor signaling including supply, Installation. Testing and commissioning of relay interlocking (RRI/PI) system for passenger carrying lines.
Defination of Similar Work :- "Trenching cable laying location and signal foundation/erection/termination/wiring in connection with any signaling work." OR "Any indoor or combined Indoor/ Outdoor Signaling work including Supply, Installation, Testing and commissioning of Relay Interlocking (RRI/PI) system for passenger carrying lines".
5 conditions · 4 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderers shall submit a copy of certificate stating that all their statements/documents submitted along with bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexurc-V, in case of other than Company/Proprietarv firm. Annexure -V(A) shall also be submitted by each member of a Partnership Firm / Joint Venture (JV) / Hindu Undivided Family (HUF / Limited Liability Partnership (LLP) etc, as the case may be. Non submission of above certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document.
Contractor shall employ following Qualified Engineers during execution of the allotted work- a] One Qualified Graduate Engineer when cost of work to be executed is Rs. 200 Lakh and above, b] One Qualified Diploma Holder Engineer when cost of work to be executed is more than Rs. 25 Lakh, but less than Rs. 200 Lakh. C] If the total cost of the tenderer's offer is Rs.25 Lakh or more, the tenderer(s) shall also give a declaration along with his/their tender to the effect that he/they shall engage and continue in service for the period of the contract, one Engineering Degree holder/one Engineering Diploma holder in line with above sub clause (a) and (b).
Mandate form dully signed by Bank Authority with seal to be attached.
GST Registration certificate of the tenderer to be uploaded alogwith tender document.
Various signaling work in connection with:(A)Provision of goodshed at Various location (i)Circulating Area & Road Widening at Kherwadi(ii)Concrete Approach Roads to GS-1 & GS-2 at Lasalgaon(iii)Provision of Office, Labour & Merchant Room at Savda & Malkapur/Akola/ Paras along with other Facility Renovation & (v)High Level Platform & COP Development at Nashik.(B)Provision of One Common room at various location of Bhusawal division, two stabling lines in DN direction at Nasik road, Development of Track machine siding at Nepanagar Station, Extension of passenger platform and stabling line at Dhule Station and Development of Rail Grinding Machine Siding at Bhusawal coaching complex yard.(C)Provision of MRIDC work:(i)ROB & LHS at Rly.Km.666/07-08(ii)ROB at Badnera Rly.Km.662/18- 19(iii) RUB at Rly.Km.545/21-22N.(D) Provision of ROB between New Amravati- walgaon Stations.(E) Elimination of Manned LCs by providing subway in lieu of (i)LC no-13 at kms 693.596 (ii)LC no-14 at kms 695.764 (iii)LC no-15 at kms 698.685 on BD-CNDB Section and (iv)LC no-17 on Badnera-Narkher Section. (F)Elimination of Manned LCs by providing subway in lieu of(i)LC no.05 on Badnera- Narkher Section (ii)LC no-12 at kms 690.09 & (ii)LC no-11 at kms 685.62 on BD- CNDB Section.(G) Elimination of Manned LCs by providing subway of size 5.0x4.5 m by push through method in lieu of LC no.(1)JK-2@ Kms 538/08-09 (2)LC noJK-5 @ Kms 543/05-06.
BSL-N-SNT-25-2026-27
BSL-N-SNT-25-2026-27
Open
Works - General
12 Months
Jalgaon, Maharashtra
₹0
₹8.0 L
24 Aug 2026
31 Jul 2026
10 Aug 2026
828 items across 20 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 43,05,871.02 | ||
| — | 6.00 | — | — | ||
| Supply of Indoor Jumper Wire of various colour as per Railways standard practice of type ATC 1 x 0.6 mm dia. conforming to IRS 76/89 (Amdt 3) or latest.(Inspection by RDSO) | — | — | — | 58,112.61 | |
| — | 3.00 | — | — | ||
| Supply of Time Element Relay (Clock work type) AG timer Siemens Make (No RSSK 30/0052). or GIC make or functional equivalent. (Inspection by RDSO) | — | — | — | 26,186.56 | |
| — | 18.00 | — | — | ||
| Supply of QTA2 AC immunised track relay, 9 Ohm,2F.1B, along with plug board, retaining clip and connectors conforming to BRS:939A, 966, & appendix F2, IRS:S34& IRS:S23. (Inspection by RDSO) | — | — | — | 77,813.97 | |
| — | 96.00 | — | — | ||
| "Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 A) With holder 1.6 A (System, Rapid or Mainad Make)."(Inspection by RDSO) | — | — | — | 8,593 | |
| — | 96.00 | — | — | ||
| Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 B) With holder 0.6 A (System, Rapid or Malnad Make) (Inspection by RDSO) | — | — | — | 8,299.47 | |
| — | 600.00 | — | — | ||
| Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92. D) Without holder 1.6 A (System, Rapid or Malnad Make). (Inspection by RDSO) | — | — | — | 15,469.44 | |
| — | 600.00 | — | — | ||
| Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92. e) Without holder 0.6 A (System, Rapid or Malnad Make) (Inspection by RDSO) | — | — | — | 15,469.44 | |
| — | 3.00 | — | — | ||
| "Resin cored wire as per specification No. IS:1921-1975 with Alloying element percentage as 63% SN (Tin) and / 37% Pb (Lead) with percentage of various impurities not exceeding the values Sb (Antimony) 0.2% maximum , Cu (Copper) 0.1% maximum, As (Arsenic) 0.05% maximum, Fe (Iron) 0.02% maximum & other impurities mainly Al, Zn & Cd shall be limited. The flux shall be free from corrosive action as per clause 5.2 & flux percentage may be used as per requirement." (Inspection by Consignee) | — | — | — | 4,208.67 | |
| — | 30.00 | — | — | ||
| Lacing thread rolls, black, wax coated (100 mtrs) (Inspection by Consignee) | — | — | — | 2,222.64 | |
| — | 26.00 | — | — | ||
| Supply of Phenolic 10mm thick sheet, grade P3 in standard size of 1.22X1.22 Mtr as per spec. No IS 2036 of 1995.(Inspection by RITES) | — | — | — | 1,52,893.98 | |
| — | 7700.00 | — | — | ||
| Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006(Rev - 2) with latest amendments and RDSO Drg.No.SA-23741 Alt.4., SA-23745 Alt 5, SA-23746, SA-23748 Alt -4 & SA-23756 Alt-3.(Inspection by RDSO) | — | — | — | 6,26,188.64 | |
| — | 60.00 | — | — | ||
| Supply of cartridge fuse block made of PBT as per RDSO Drg No SA-23748 Alt 4,SA- 23749 & Spec No IRS S 75/2006 with latest amendment. Fuse block shall be suitable for round head type voltage fuses.(Inspection by RDSO) | — | — | — | 10,949.57 | |
| — | 60.00 | — | — | ||
| Supply of round head type non detoriating type low voltage cartridge fuse as per Specn No IRS/S/78/92 with latest amendments (i) 2A/4A/6A capacity (Inspection by RDSO) | — | — | — | 4,712.74 | |
| — | 24.00 | — | — | ||
| Supply of Tik-tak, piano type switches,5 A Make-Anchor or Cona(As per IS specification).(Inspection by Consignee) | — | — | — | 898.06 | |
| — | 140.00 | — | — | ||
| Supply of Lamp 110V/24W,2 Pin for Loc.(Inspection by Consignee) | — | — | — | 3,564.06 | |
| — | 26.00 | — | — | ||
| Supply of Apparatus Case with godown locks or miniature 'E' type locks with deatachable handle on both the doors. (i) Single Case as per Drg No SK 783-1&2. with latest alteration.(Inspection by RITES) | — | — | — | 4,66,503.86 | |
| — | 12.00 | — | — | ||
| Supply of Apparatus Case with godown locks with deatachable handle on both the doors. (b) Half Case as per Drg No SK 783-1&2. with latest alteration.(Inspection by RITES) | — | — | — | 1,72,756.95 | |
| — | 38.00 | — | — | ||
| Supply of earth electrode assembly as per Drg.No.CR/S&T/SK/815(Inspection by Consignee) | — | — | — | 45,883.08 | |
| — | 24.00 | — | — | ||
| Supply of Track Lead Juction Boxes as per C.Rly Drg. No.RST 11509 made from fiiber glass along with terminal blocks.(Inspection by Consignee) | — | — | — | 28,169.7 | |
| — | 24.00 | — | — | ||
| Supply of B type choke to specn.No.IRS.S.65/83 (Amdt -3) with latest amendments. (Inspection by RDSO) | — | — | — | 98,551.49 | |
| — | 24.00 | — | — | ||
| Supply of adjustable Track Feed Resistance disc type 7.5/15/30 ohms as per RDSO Drg. No. SA 20161-66/M (Adv) with latest amendments (with Phenolic moulded base).(Inspection by RDSO) | — | — | — | 34,625.2 | |
| — | 24.00 | — | — | ||
| Supply of Track feed battery chargers, 110V AC input 2, 4 to 6 V DC Output to Specn. No.IRS. 89/2013/Ver 1.0 with latest amendments. Charger shall be suitable for charging 80 AH battery.(Inspection by RDSO) | — | — | — | 65,326.46 | |
| — | 3000.00 | — | — | ||
| Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No IRS S 17-75 Revision 3 .(Inspection by Consignee) | — | — | — | 6,753.6 | |
| — | 1200.00 | — | — | ||
| Supply of PVC jacketed wire rope for Track Lead connections. PVC jacketed wire rope should be of Galvanised steel wire rope 6 mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS:2266:2019. Reclaimed or recycled material should not be used.(Inspection by Consignee) | — | — | — | 70,277.76 | |
| — | 24.00 | — | — | ||
| Supply of Hydrometer, Exide make or similar for measuring specific gravity of Battery Graded acid with mounting stand in location Boxes.Consignee inspection under manufacturer certificate.(Inspection by Consignee) | — | — | — | 7,624.24 | |
| — | 162.00 | — | — | ||
| Supply of GI pipe, inner dia. 100mm dia. B-class as per spec. No.IS 1239 PT.1/2004 or latest with sockets and fittings. TATA/JINDAL/ZENITH BIRLA Make.(Inspection by RITES) | — | — | — | 1,86,759.82 | |
| — | 378.00 | — | — | ||
| Supply of DWC HDPE Pipe with one snap fit coupler and 'O' ring fire resistant, anti rodent,in 6mtr length of size 120 mm outer dia as per RDSO /SPN /204/2011/Ver 1.1 with Amdt 1 or latest.(Inspection by RITES) | — | — | — | 1,36,080.6 | |
| — | 3732.00 | — | — | ||
| Supply of RCC pipe half round of size 300mm dia outer and 250 mm dia internal 1 mtr long. matching to IS No.458/2003 amendment-1 with Rev.4.(Inspection by RITES) | — | — | — | 17,64,937.44 | |
| — | 1200.00 | — | — | ||
| Supply of Modular Terminal block of 2.5 sqmm 2 IN 2 out type disconnect type terminal along with as per RDSO Specn.No.RDSO/SPN/189/2004 Rev 3.0. The current capacity of 16 Amps & more,The terminal should have marking at centre to view description from front.Material to be procured from RDSO approved firm only.(Inspection by RDSO) | — | — | — | 1,57,409.28 | |
| — | 18.00 | — | — | ||
| Supply of DIN channel for the terminals 1 Mtr each(Inspection by Consignee) | — | — | — | 4,369.28 | |
| — | 48.00 | — | — | ||
| — | 12.00 | — | — | ||
| Supply of thermo shrink Jointing kit (Reinforced) TSF-2 type generally conforming to R D S O Specification No.RDSO/SPN/TC/77/2015 Rev 1 with modified kit contents as per CSTE Specification No.CR/SPN/TC/57 (A)/2015 dtd 06.01.2015(Table -A) to be suitable for jointing both 10/20/50 pair PIJF and 4/6 Quad cables along with sub-kit(Table-B) for armour continuity. (Inspection by RDSO) | — | — | — | 40,212.08 | |
| — | — | — | 67,40,866.88 | ||
| — | 1.00 | — | — | ||
| Supply of Relay Rack Assembly complete with scaffolding, fixtures and accessories including MS Bars for fixing of relay plug board, string rods, fuse strips with bracket, 11 Way Bus Bars with cover and mounting brackets, runway for cable/wires, frame, base assembly etc. Siemens type & as per extant practice on C. Rly. Typical part list as per Annexure-II and Rack arrangement as per Sketch no SK-727 and Rack plan as approved by Engineer incharge. (Inspection by CONSIGNEE) | — | — | — | 32,388.7 | |
| — | 10.00 | — | — | ||
| Supply of Tag Blocks 200 / 160/120 way with polycarbonate cover as per IRS S 77- 2006 (Rev 1 ) RDSO DRG. NO SA 24751, SA 24752 & SA 24753 Requirement of each type shall be specified by Engineer incharge . (Inspection by RDSO) | — | — | — | 12,981.52 | |
| — | 1.00 | — | — | ||
| Supply of Tag Blocks 96/ 100 way with polycarbonate cover as per IRS S 77-2006 (Rev 1 ) Requirement of each type shall be specified by Engineer incharge . (Inspection by CONSIGNEE) | — | — | — | 1,373.53 | |
| — | 1.00 | — | — | ||
| Supply of Main Cable Termination rack complete with scaffolding, fixtures & accessories including square bars for mounting 8-way terminal blocks, ladder, string rods, frame, base assembly, insulators, J bolt, nut/bolts & fasteners, backelite sheet, etc. Siemens type and as per extant practice on Central Railway. Typical part list as per Annexure-III and rack arrangement shall be as per sketch No. SK-727 with latest alterations. (Inspection by CONSIGNEE) | — | — | — | 27,895.67 | |
| — | 5.84 | — | — | ||
| Supply of PVC Indoor Cable 1x60x0.6mm dia colour coding of insulation of inner core shall be in six colour Viz Blue , Red , Grey ,Green, Brown and Black conforming to IRS 76/89(Amdt 3) or latest. (Inspection By RDSO) | — | — | — | 16,11,081.12 | |
| — | 5.41 | — | — | ||
| Supply of PVC Indoor Cable 1x 40x0.6mm dia. Colour coding of insulation of inner core shall be in eight colour viz blue, Red, Grey, Green, Brown, Black, Yellow & white. conforming to IRS 76/89 (Amdt 3) or latest. (Inspection by RDSO) | — | — | — | 9,79,086.88 | |
| — | 0.50 | — | — | ||
| Supply of PVC indoor cable 1 x 24 x 1 mm dia. Colour coding of insulation of inner Conductor shall be in eight colour viz Blue,Red,Grey,Green,Brown,Black, Yellow & white.conforming to IRS 76/89 (Amdt 3) or latest. (Inspection by RDSO) | — | — | — | 1,34,247.58 | |
| — | 6.60 | — | — | ||
| Supply of Indoor Jumper Wire of various colour as per Railways standard practice of type ATC 1 x 0.6 mm dia. conforming to IRS 76/89 (Amdt 3) or latest. (Inspection by RDSO) | — | — | — | 52,366.21 | |
| — | 0.50 | — | — | ||
| Supply of Indoor Jumper Wire ATC 1 x 1 mm dia. conforming to IRS 76/89 (Amdt 3) or latest. (Inspection by RDSO) | — | — | — | 6,006.66 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCAllcorrectionslips.pdf
ATTACHMENT
SORdrawingDrawingsAnnexures_compressed.pdf
ATTACHMENT
Annexure-ASafety-CriticalSignalingItemsbyRDSO.pdf
ATTACHMENT
CorrectionslipGCC13032026.pdf
ATTACHMENT
TenderDocument25-26-27.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .