Bikkatty Town Panchayat O and M Gap Filling FUND - 2025-2026

Amount

Earthwork excavation for Open Cutting and depositing on Bank within initial lead of 10mt and lift of 2mt of all soil except rock etc., complete complying with standard specification.

Earthwork excavation for foundation and depositing on Bank within initial lead of 10mt and lift of 2mt of all soil except rock etc., complete complying with standard specification.

Clean removal Old Damaged Plastered Surface The Rate including cost and conveyance of all materials to work site and labour charges etc., complete complying with standard specification.

P.C.C.1:4:8 mix using 40mm metal and the rate including cost and conveyance of all materials to work site and labour charges etc., complete complying with standard specification.

Supplying and erecting steel centering for the sides and soffits of RCC slab or plane surfaces excluding strutting and the rate including cost and conveyance of all materials and labour charges etc. Complete complying with standard specification.

Below 1 M

Above 1 m

Plain Cement Concrete 1:3:6 Mix (one part cement, three part sand and six part of aggrigate) using 20 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc. complete. Complying with std. specification

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications

Supplying, fabricating and placing in position of steel rods (M.S or RTS) including cost of binding wire and the rate including cost and conveyance of all materials and labour charges etc. complete complying with standard specification.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Supply and Fixing of (Half Cutter) RCC Hume pipe 300mm Dia and the rate including cost and conveyance of all materials to site and all labour charges etc.. complete

Plain Cement Concrete 1:2:4 Mix (one part cement, two part sand and four part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Special Ceiling Plastering in cm 1:3 mix to 10mm thick and the rate including cost and conveyance of all material and labour charges etc. Complete complying with standard specifications.

Plastering in cm 1:5 mix to 12mm thick and the rate including cost and conveyance of all material and labour charges etc. Complete complying with standard specifications.

Painting the walls two coats over the old Plastered surface of priming with best Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers etc., complete complying with standard specifications.

Supplying and fixing in position of M.S. door and MS Windows the rate including cost and conveyance of all materials and labour charges etc., complete complying with standard specifications.

Painting two coats on new ironwork using best-approved quality of ready mixed enamel paint and the rate including cost of all charges etc., complete complying with standard specifications.

Painting two coats on old ironwork using best-approved quality of ready mixed enamel paint and the rate including cost of all charges etc., complete complying with standard specifications.

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains ( SD 65 )

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm withsupporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank onwall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit (SD 125)

Supply and run of 2 of 4 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm G.I pipe (Class 'B' bent at both ends with necessary angle iron up right and end supports for mains (SD No.70) Page No -37

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC open light / fan Point (for electronic regulator) (5 points per coil) (SD 20) Page

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitablePVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mmTW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion withsuitable colour for open PVC plug point (SD 36) Page

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for15W CFL lamp with LED. SD 83

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush typeswitch with continuous earth wire connection of 14 SWG TC wire and making good of the open portion withsuitable colour for open power plug point (SD 39) Page 25

Supply and fixing of 16A TPN metal clad switch on suitable angle iron frame work with MS cable entry boxes with earth connection only (SD 146 ) Page 64

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flutube with PVC unsheathed copper leads from terminals to the fitting (SD 88 ) Page No.44

Floor finishing with fully vitified tilles using best quality of fully vitified tiles of size 60cm x 60cm x 6mm over the base plastering cement mortar 1:3 mix, 20mm thick pointing with using white cement 4kg/10sq.mt. inculing cost and conveyance of all materials and all labour charges. Etc. complete.

Supplying and fixing in position best Indian make colour glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications.

Supplying and fixing of Special Type Mirror of Size 1000 x 780 mm including cost and conveyance of labour charges for complete complying with standard specification

Supplying and fixing of SS Towel Rail including cost and conveyance of labour charges for complete complying with standard specification

Supplying and fixing of Special Type Mirror of Size 1000 x 780 mm including cost and conveyance of labour charges for complete complying with standard specification

Supplying and fixing of mild steel hallow sections of square and rectangular pipes and the rate including the cost of materials, trasporting charges, labour charges for welding and fixing charges and all other incidential charges to work site etc., complete complying with standard specification.

Supply and fixing of PUF roof panels made up of minimum 0.5mm thick PPGI corrugated Sheet at the top and a plain sheet at the bottom with a layer of rigid CFC free polyurethane foam (PUF) of density 40kg + 2 Kg/cum as insulation in between .The polyurethane foam shall confirm to latest IS 12436. The minimum thickness of PU foam layer shall be 29mm for having 30mm (min) thick PUF panel. The PPGI Sheets shall be of minimum 240 MPA Steel Grade & shall have a Zinc coating of minimum 120 GSM as per IS 277/1992, 5-7 microns of epoxy primer on both sides of the sheet & polyester top coat of 18-20 microns on one side / outer side. The PPGI Sheets / PUF Panels shall have a protective guard film of minimum 20-25 microns to avoid scratches to finished panel during transportation. Providing ridges or hips ,encasing the ends of Panel with plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers etc complete excluding the cost of trusses, purlins and inclusive of cutting to size and shape wherever required.