SPECIAL REPAIRS TO JCOs MD ACCN BLOCK NO P1 AND P5 AT MCEME UNDER GE MCEME SECUNDERABAD

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding (including backing coat backing ) removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 450x300x 7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backing coat in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

M & L for coloured tiles, Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

M&L for Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and directed by Engineer-in-Charge.

Rounding off edges of granite platform/urinal partition, complete all as specified and directed by Engineer-in-Charge.

M&L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement plaster 1:6, complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in roofs / floors other than ground floor of any desctription and position, complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, complete all as specified and directed by Engineer-in-Charge.

M & L for rendering 10mm thick in cm (1:3) on concrete surfaces of roof padding with integral water proofing compound (water proofing compound to be paid separately ) finished even & smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-Charge.

M&L APP based polymeric membrane minimum weighting 3 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gm/Sqm) laid on primed surface by forced application over a coat of a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces, complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in any position otherwise not specifically provided for, complete all as specified and directed by Engineer-in-Charge.

M & L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type E-2, 1:5:10 (using 40mm graded stone aggregate) as in filling and mass concrete as in sunken floors, complete all as specified and directed by Engineer-in-Charge.

M& L Rendering15 mm thick in CM (1:3) on sunken concrete floor surfaces mixed with integral water proofing compound finished even and smooth without using extra cement (WPC shall be measured & paid separately) complete all as specified and directed by Engineer-in-Charge.

M&L for providing and applying brush applied water based PU dispersed polymer modified Elastomeric liquid membrane, ShaliUrethane BTD with Zero VOC or of any approved make-STP/Fosroc/BASF to form the membrane in situ at site with 3 layers of monolithic, seamless finish having >500% elongation. The first layer is to be formed mixing with clean water in the ratio of 1:1 @ 400 Gms per Sqm and shall act as the prime coat to fill in the cavities. This can be brush or roller applied. For spray application, using any airless spray system with recommended nozzle size at 30:1 at 2 bar pressure. Providing and applying the second coat @ 1 kg per Sqm using the soft brush, roller or spray system with the recommended nozzle size on to the primed surface. Providing and applying 50 Gsm fiber cloth over the 1st coat, when substrate till the coat is tacky. Providing and applying 3rd coat @ 1kg/Sqm to finish the application for a thickness of 1.5mm membrane formed in place. The second coat should be applied perpendicular to the first coat for cross linkage and complete as per the specification and all as directed.

Demolition of Brick work or stone boulder masonry, built in cement mortar or cement lime mortar, complete all as specified and directed by Engineer-in-Charge.

M&L Brick work with fly ash modular bricks, straight or curved on plane exc 6m mean radius built in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls of any description including racking out joints hacking for keys scrubbing down with water, complete all as specified and directed by Engineer-in-Charge.

Rendering 10mm thick in CM 1:6 on brick work or concrete surface is to be finished even and smooth (without using extra cement) , complete all as specified and directed by Engineer-in-Charge.

Rendering 15mm thick in two layers, 5mm thick in CM 1:4 over 10mm thick in CM 1:6, on brick work or concrete surface is to be finished even and smooth, without using extra cement, with integral water proofing compound (water proofing compound to be paid separately ) , complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5 mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L for Two coats of Distempering with oil emulsion distemper on newly plastered surfaces of walls over two coat of wall care putty over a coat of alkali resistance primer including preparation of wall surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation newly plastered surfaces of wall and cornices and applying two coats of acrylic weather proof painting over one coat of primer on wall to make surfaces smooth and good, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old decorated wall surface and applying two coats of OBD over two coat of wall care putty, complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatement including preparation of old decorated surfaces of wall and cornices and applying two coats of acrylic weather proof painting on wall to make surfaces smooth and good, complete all as specified and directed by Engineer-in-Charge.

M&L Preparation of old decorated surfaces of ceiling and applying one coat of white wash , complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description area exc 1.00 Sqm and not exc 2.00 Sqm each , complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters n.exc 1.5sqm (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.50 Sqm and not exc 4.00 Sqm each , complete all as specified and directed by Engineer-in-Charge.

Taking down,Chowkhats or frames exc. 1.5 sq. m and n.exc. 4 Sqm each, but with shutters (without taking off shutters from the frames), complete all as specified and directed by Engineer-in-Charge.

S/F pressed steel door frame 125 x 60mm with one or more rebats including fixing lugs, hinges, lock strike plate etc complete all as specified and directed

S/F pressed steel door frame 105 x 60mm with one or more rebats including fixing lugs, hinges, lock strike plate, complete all as specified and directed by Engineer-in-Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frames shall be covered with head moulded plain colour PVC ‘C” channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, and bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded and sealed to the stiles rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing , complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinges extruded aluminium alloy with brass/bronze hinge pin in lieu of mild steel min , complete all as specified and directed by Engineer-in-Charge.

S/F 150mm size aluminium anodised handles, fabricated type , complete all as specified and directed by Engineer-in-Charge.

S/F 150mm long aluminium anodised barrel tower bolt of extruded section , complete all as specified and directed by Engineer-in-Charge.

S & F 35 mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on face is covered with decorative face veneer both sides , complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description fixed in any position with nails, complete all as specified and directed by Engineer-in-Charge.

M & L for 18/19 mm thick, Prelaminated particle board, interior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work, complete all as specified and directed by Engineer-in-Charge.

M & L 2nd class hardwood exc 3 & n exc 6 sqcm plain fillets.'square,rectangular or triangular insection, clean sawn, secured with nails orbrads , complete all as specified and directed by Engineer-in-Charge.

S&F continuous (Piano ) Hinges 30 mm width of flaps, mild steel bright finish or elecrogalvanised complete all as specified and directed by Engineer-in-Charge.

S&F 100mm aluminium barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm size Hasp and staple, Aluminium anodised, wire type, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished all as specified and as directed.

M&L mild steel Mortice locks 65 mm size 4 lever type for cupboards , grade- 1 vertical type complete all as specified and directed by Engineer-in-Charge.

S&F of 35mm thick Second class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc. divided in to square with plain chamfered or rounded mitred and rebated sash bars, any numbers, edges of framing plain chamfered or , complete all as specified and directed by Engineer-in-Charge.

S&F Windows/ventilators (NCL ECO–4000 Series Windows (Double Rebate Windows) or equivalent) fabricated from roll framed sections made of galvanized steel colour coated/powder coated (Base steel as per IS-513 “D” quality galvanized as per IS-277 with zinc of 120 gms/Sqr. Mtr.) with total coated thickness of 0.58mm. Sections for Frame should be of 72x55mm, Section for Mullion should be of 72x50mm, Section for Shutter Frame should be of 47mm x 20mm, Section for Fixed Glass Bead should be of 12x12mm, and Section for Fly Mesh should be of 40x20mm Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined with Frame/Mullion using Mullion Cap Ethyl Propylene Damien Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. Spoon Section should be used around Fly mesh to fix Mesh in Mesh Shutter including SS Pivot Hinges–1 set, Seccolor Handle & Seccolor Stay and 4mm Plain Float Glass and Stainless Steel 32 gauge Fly mesh of 25 holes per SqCM and powder coated Grill made of 10mm sq. MS Bars welded at 150mm c/c, 6x12mm MS flat and fixed to window frame with screws , complete all as specified and directed by Engineer-in-Charge.

S/F Stainless Steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless Steel wire staples along with frame work of windows / ventilators with all necessary arrangements, complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium butt hinges extruded aluminium alloy with galvanised anodise and of size 100mm (Type C-21) , complete all as specified and directed by Engineer-in-Charge.

S&F 200mm long Aluminium anodised or matt finished barrel tower bolt of extruded section , complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodised handles fabricated type of size 150mm , complete all as specified and directed by Engineer-in-Charge.

S & F for Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 250 mm, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm size hasp and staple, safety type, aluminum anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge.

S & F for Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing,rames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles,Articles n exc 5 kg each, complete all as specified and directed by Engineer-in-Charge.

M&L for PVC (SWR) floor trap,plain with grating incl jointing with solvent cement 75mm bore, complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm bore PVC(SWR) pipe single socket in any length with rubber ring joints fixed to walls/laid in floors incl removal of old pipes, complete all as specified and directed by Engineer-in-Charge.

M&L for PVC (SWR) pipe 110mm dia fixed to walls and floors single socket with rubber ring joints, complete all as specified and directed by Engineer-in-Charge.

M&L for bends PVC (SWR) 110 mm dia of any radius,fixed to walls/laid in floor , complete all as specified and directed by Engineer-in-Charge.

- do - all as per item no. 63 above but 110mm with oval acess door, complete all as specified and directed by Engineer-in-Charge.

M&L for bends PVC (SWR) 75mm dia of any radius,fixed to walls/laid in floor , complete all as specified and directed by Engineer-in-Charge.

- do - all as per item no. 65 above but 75 mm with oval acess door , complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia complete all as specified and directed by Engineer-in-Charge.

S/F 15mm bore fancy type stop valve brass CP (concealed ) screwed down,high pressure,with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed , complete all as specified and directed by Engineer-in-Charge.

S&F CP bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe of dia 15mm, fancy type fixed in repairs complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for 15mm dia stop valves/ angle valves , with crutch or butterfly handles, fancy type, chromium plated, screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-Charge.

S & F 140mm long floor door stopper aluminum body with rubber shoe nut (2 each in one stopper) with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge.

M&L Rotational moulded polyethylene water storage tanks 1000Ltr (cylinderical vertical with closed top) including dismantling water tanks and also necessary float ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed .(Minimum weight 20mm - 210 gms) hoisted and fixed in position , complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Gun metal gate valve, with iron wheel head screwed both ends for 20 mm bore pipe, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Brass chromium plated shower rose 125 mm size with or without swivel joints , any size including fixing to steel pipe or union, complete all as specified and directed by Engineer-in-Charge.

S&F SS soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed by Engineer-in-Charge.

M/L for preparation of new wooden surfaces of any description,over 10cm in width or grith with two coats of synthetic enamal paint over a coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

M/L for preparation of old wooden surfaces of any description,over 10cm in width or grith with one coats of synthetic enamal paint, complete all as specified and directed by Engineer-in-Charge.

M/L for preparation of new steel surfaces of any description,over 10cm in width or grith with two coats of synthetic enamal paint over a coat of red oxide complete all as specified and directed by Engineer-in-Charge.

M/L for preparation of old steel surfaces of any description,over 10cm in width or grith with one coats of synthetic enamal paint including preparation, complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china Orissa pattern squatting pan 580 x 440mm with integeral foot rests including P or S trap, complete all as specified and directed by Engineer-in-Charge.

S&F in repair, PVC valveless, 10 litrs, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, etc complete all as specifed and directed.

S&F 15 mm dia 600 mm long PVC water connection with PTMT nuts and washers, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Wash basin vitruous china 550 X 440mm long white colour flat back incuding and MS brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, Bore dia of pipe in 15 mm, etc complete all as specifed and directed.

S & F for Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms), Bore dia of discharge pipe in 32 mm, complete all as specified and directed by Engineer-in-Charge.

Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches, Bore of pipes in 32mm, complete all as specified and directed by Engineer-in-Charge.

Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches, Bore of pipes in 40mm, complete all as specified and directed by Engineer-in-Charge.

M & L for Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed Bore dia of pipe in 40 mm, complete all as specified and directed by Engineer-in-Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engineer-in-Charge.

S&F Grating round 125 mm size of PTMT (minimum weight 40 gms) , complete all as specified and directed by Engineer-in-Charge.

S&F Brass chromium plated Tubular towel rail in repair , 20 mm dia , D type 60 cm long between flanges, complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing & connections , 15 mm dia , complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing & connections , 20 mm dia , complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia, steel water tubing 'Medium grade' galvanised with all fittings & fixed complete to walls & ceilings or laid in floors , complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm dia, steel water tubing 'Medium grade' galvanised with all fittings & fixed complete to walls & ceilings or laid in floors , complete all as specified and directed by Engineer-in-Charge.

Cutting chases ,pinning in making good to facing where required of brick walls and pointed in cement mortar 1:3 for concealed water tubing etc cutting not exc 10 cm girth, complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long MS ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed by Engineer-in-Charge.

S&F CP curtain rod/drapery rod 20mm dia of approved pattern and quality with decorative stainless steel backets of approved quality, complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/ dense soil , complete all as specified and directed by Engineer-in-Charge.

Excavating over areas, n exc 1.5m deep and getting out hard/dense soil, complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in surface channelor drain, complete all as specified and directed by Engineer-in-Charge.

M&L brick work with sub class 'B' bricks old size straight or curved on plan exc 6 mtr mean radius built in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

M&L cement type C2 1:3:6, using 40mm aggregate in surface channel and drains etc., complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping, including formed work, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in precast RCC manhole covers including all form work and set in cm 1:4, complete all as specified and directed by Engineer-in-Charge.

M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, TMT bars,etc, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm , complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point in soils, complete all as specified and directed by Engineer-in-Charge.

M&L for sand cushion/bed for laying interlocking tiles / paver blocks, complete all as specified and directed by Engineer-in-Charge.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with gery cement and no pigment, , complete all as specified and directed by Engineer-in-Charge.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / Hylam sheet/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specified and directed by Engineer-in-Charge.

Material and labour for concealed point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multistranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked of suitable dia conduit concealed wiring including Tee, Junction boxes and provision of 2.0mm thick MS terminal boxes duly painted with red oxide metal primer and covered with 3 mm thick sheet cover of suitable size including suitable screws with washer for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to common earth dolly including cutting and chassing of wall complete all as specified & as directed for One light point controlled by one, one way switch 5 amps, SP complete all as specified and directed by Engineer-in-Charge. Note:- Wiring to be carried out in existing pipe in celing/roof.

All as per item No.113 above but for One light point controlled by two 2 - way switches

All as per item No. 113 above but for One Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator

All as per item No 113 above but for One bell point controlled by one bell push switch

All as per item No. 113 above but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

All as per item No. 113 above but for One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No. 113 above but using 4.0 Sqmm single core copper conductor cable multistranded PVC insulated unsheathed 1100 volts grade for 3 pin 15 Amps switch socket combination point including running 4.0 Sqmm copper conductor PVC wire as earth continuity conductor on independant board.

Supply and fixing of Switch piano , single pole one way, flush type 5 Amps capacity 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing bell push 5 Amps, single pole flush type one way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 2 way switch 5 Amps, single pole flush type complete all as specified and directed.

Supply and fixing of socket outlet 2 in 1 multipurpose 2/3 pin 5 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of switch socket combination 2 in 1 multipurpose 2/3 pin 5 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch socket combination 2 in 1 multipurpose 3 pin 5/15 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of electronic ceiling fan regulator stepped type suitable to work on 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Bell ding dong, AC 230 Volts, SP complete all as specified and directed.

Supply and fixing of ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed by Engineer-in-Charge.

Material and labour for concealed Submain wiring with 2 runs of single core 6 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid PVC conduit and conduit accessories of medium grade not less than 25 mm dia including one run of single core 6 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board including cutting and chassing of wall & removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified and as directed.Note:-Two runs of cable, one run of earth contuinity conductor and one run of conduit shall be measured as one unit length complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed . Make:- Havells/Bajaj/Crompton.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed Make:- Havells/Bajaj/Crompton.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Make:- Havells/Bajaj/Crompton.

Supply and fix LED energy efficient building security light fitting of capacity of 35 W for fixing in GI pipe bracket on wall all as specified and directed. NOTE : GI bracket, clamp, nut and bolt etc will be measured in separate item. Make:- Havells/Bajaj/Crompton.

Supply & fixing galvanised iron tube bracket of 40 mm dia light grade and 1.2 mtr length for fixing building security light, with all fixing arrangement including necesssary clamp, nut and bolt etc. as required size all as specified and as directed.

Supply and fixing lamp holder insulated body with back plate for angle batten fitting fixed with round block including LED bulb 9 W non dimmable type complete all as specified and directed.Make:- Havells/Bajaj/Crompton.

Supply and fix sheet metal enclosure with double pole and Earth Metal Plug & Socket including 20A SP MCB 240V C curve complete including taking down unserviceable enclosure all as directed by Engr in Charge.

Disconnecting and removing ceiling fan of 1200/1400 mm sweep from any height from electrical connections, bringing down, taking out defective winding and rewinding of the ceiling of any size complete with equivalent new super enamelled copper wire as per existing gauge and weight as per manufacturer's design , cleaning internally and externally, replacement of split pins, cotter pins and check nuts etc , reassembling, replacement of minor worn out/ defective parts, changing of capacitor , rotor , shaft etc and painting of celing fan with sythetic enamel paint by spray painting and testing on completion and refixing in original position complete all as specified and directed. NOTE: Cost of rewinding/capacitor/clamps/rotar/shaft or any connected items is deemed to be included in quoted rate.

Disconnecting and taking down geyser 25 Ltrs , cleaning , servicing, and refixing with anchor bolts complete all as specified and directed.

Supply and fixing PVC cold water connection pipe 60 cms long 15 mm dia for Cold / Hot water apparatus (Geyser 25 / 50 Ltrs Capacity) all as specified and directed.

Supply and fixing Gate valve 20 mm dia for inlet pipe connection of the geyser all as specified and directed.

Supply and fixing Geyser element 2000 watts any type for Hot water apparatus (Geyser 25 ltrs) all as specified and directed

Supply and fixing thermostat for Hot water apparatus(Geyser 25 lits) all as specified and directed.

Supply and fixing Exhaust fan, heavy duty, 230/300 mmsweep metal body with louvers, AC single phase, 230 Volts, 1400 rpm and connecting up with and including necessary 3 core PVC insulated copper flexible cord of size 23/0.019 from exhaust fan to the ceiling rose including making hole in the wall and making good edges in cement plaster complete all as specified and directed. Make:- Havells/Bajaj/Crompton.

Supply and lay on wall/in ground/on pole ISI marked XLPE insulated armoured, heavy duty, electric cable with aluminium conductors 1100 volts laid in trenches, floors, ducts, pipes drawn across the road/paths/drain/along poles/walls/floor/equivalent etc including jointing & testing complete all as specified of size 35 Sqmm , 3.5 core all as specified and directed. Make:- Havells/Gloster/Finolex

Excavation in trenches not exceeding 1.5 mtr width and not exc 1.5 mtr in depth and getting out in hard /dense soil for laying / repairing of LT cable / GI pipe complete all as specified and directed by Engineer-in-Charge.

Supply, spread river sand of approval in cable trenches providing for cable cushioning as directed. NOTE :- Punned thickness of sand only will be measured and paid complete all as specified and directed by Engineer-in-Charge.

Removal of surplus soil to a distance not exc 50 mtrs away and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Returning , filling incl spreading levelling watering and well ramming in layers not exc 25 cm thick complete all as specified and directed by Engineer-in-Charge.

Supply and lay PCC cable covers for LT cable protection, Class LV, Type 1 of size 250x150x40mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing medium grade GI tubing of 50 mm dia for XLPE cable protection complete all as specified and as directed

S & in replace of Vertical type MCCB TPN DB 4 way double door made out of CRCA sheet housing with powder coating complete all as specified and directed.

Supply and replace MCCB 4P, 415V,16KA, 100 amps suitable for Vertical MCCB DB all as specified and directed .

Supply and replace MCB double door DB SPN 8 way with 200 Amps busbar including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair MCB SPN 40 Amps 240V C curve for fixing on MCB DB complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair MCB SP 6 to 40 Amps 240V C curve for fixing on MCB DB complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground to a depth not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 m below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, checknuts and washers all as shown in Electrical Plate No.3 of SSR Part-I and connected to main switch board including excavation and earth work, PCC chamber in 1:3:6, RCC Cover in 1:2:4 type B-1 reinforced with 8 mm dia MS bars at 10 cm c/c, 20 mm dia medium grade GI pipe with funnel and wire mesh complete and watering arrangement all as specified. (Note: GI pipe 15mm dia, GI wire 4mm dia upto 7.5m deemed to be included in quoted rate.) complete all as specified and directed by Engineer-in-Charge.

M/s D.Krishna Varma

MAHALAKSHMI INFRA PROJECTS

P VIJAY KUMAR

K LAKSHMAN SINGH AND CO

A SOMA RAJU

STANDARD AGENCIES