ADDITION / ALTERNATIONS AND SPECIAL REPAIR TO ROLLING SHUTTERS, GALVALUME SHEETS AND VALLEY GUTTER OF PATLIPUTRA (BUILDING P-36) UNDER GE HADDO PORT BLAIR

Amount

M & of submain wiring in rapair with 2 runs of 6.0 Sp mm multistranded copper conductor PVC insulated (FRLS), 1100 Volts grade and one run of 6 sqmm PVC insulated (FRLS) multistranded copper earth continuity conductor including lugs of suitable size drawn in and including rigid PVC casing & caping of suitable size but not less than 32 mm width complete all as directed. Make of wire: Polycab/Gloster/Anchor/Havells/ Finolex and make of PVC conduit: Modi/ Precision/ Supreme/ Finolex/ Polycab NOTE: Tow runs of 6.0 Sqmm cable, one run of 6 Sqmm cable alongwith PVC casing & caping shall be measured as one unit.

S & F SPN DB sheet metal enclosure double door suitable (IP-43) Protection 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated compete. Make : Indo Asian/ Havells/ L & T.

Supplying & fixing MCB SPN 40 Amps (`C’ series) having current rating 10 KA complete all as specified and directed Make : Indo Asian/Havells/L&T

Supplying & fixing MCB single pole, 6 to 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed Make : Indo Asian/Havells/L&T

Supplying, installatin, commissioning testing of Motorized Heavy duty Industrial Rolling Shutter of size: 05 mtr (wide) x 5.5 mtr (hight)mtr made of 1.25mm thick steel sgheet with all ball bearing or specified including top cover anchoring rod and hasp and staple with fire resistance paint, control unit with electric control device, additonal mechanical control unit for emergency operation fabrication, fitment and all fixing and arrangement as per requirements all as specified and directed by Engineer-in-Charge. Note:- The above quoted rate is included for civ work (any type), cutting, welding work etc for completetion the entire work.

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion.

Dismantling plain or corrugated steel sheeting any gauge, thickness including similar pattern roof coverings.

S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering fixed with self tapping screws complete all as specified and directed by Engg-in-Charge..

S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws complete all as specified and directed by Engg-in-Charge.

S&F for fibre glass reinforced transulcant corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc., 2 mm thick of any colour as in roof covering fixed with self tapping screws complete all as specified and as directed.

M&L plain aluminium flat section not less than 0.68 Kg per Rm as in wind tie fixed with aluminium self tapping screws etc.complete all as specified and directed by Engg-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed or fixed with beads at roof level complete all as specified and as directed by the Engineer-in-Charge.

S&F solid poly carbonate sheet 4 mm thick with required side lap fixed in position on steel frames up to 10 m in height with required screws etc., in wall cladding at roof level complete all as specified and as directed.

Dismantling structural steel work complete all as specified and directed by Engg-in-Charge.

M&L for rolled sections as in main and cross beam, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates of grade Fe 410 (grde E-250)

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Dismantling of 150mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out if reqd.

S&F for 150mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F for 150mm dia PVC (SWR) bends any radius complete all as specified.

Taking down cement plaster on brick /stone masonry / concrete surfaces of wall / ceiling incl raking out joints, hacking for key, scrubbing down with water etc and deposited the debris outside the MD land complete all as specified and directed.

M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth (without using extra cement) all as specified.

Taking down of damaged, loosened cement concrete/cement mortar in RCC walls/soffits of slabs, beams columns and similar structure members up to depth of 20mm to 40mm cleaning the dismantled portion with wire brush etc remove dust , dirt and other foreign particles etc and washing with water with pressure and applying bonding agent on old concrete surfaces all as per manufacturers instruction, Over prepared surfaces provide 20 mm thick High build polymer modified cement sand mortar ( 1:2.5 ) mixed with 10 liters (minimum) Nitobond SBR per 50 kilogram of cement of M/s FOSROC chemical ( India ) Pvt Ltd or Equivalent product of manufacturer all as manufacturers instruction including necessary scaffolding up to 12 m complete all as specified and directed by Engg-in-Charge.

M&L for preparation of newly plastered wall surfaces with 3 mm average thick wall care putty and applying two coat of oil bound distemper over one coat of alkali resistant primer including leveling the surface which undulation found with cement putty etc complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall by washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of acrylic emulsion distemper over one coat of alkali resistant primer including filling of cracks, holes and including leveling the surface which undulation found with wall care putty etc.. all as specified.

M&L for preparation of old steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer all as directed.

A PALANI

CARTWHEEL CONSTRUCTION

Reliance Sales Agency

CHANDER SEKER ENTERPRISE

M/s Ramesh Lal

M/s K Moorthi