Construction of office cum training Centre on the plot of land at community Centre , Saket , New Delhi

GRAND TOTAL 5668,33,961.26

and dressing complete.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 1.5 cm.

deep and disposal of rubbish lead upto 50 m and lead upto 1.5 m

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up

5 2.31 to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of sqm 1,320.00 17.60 17.12 22,604.74

50 m outside the periphery of the area cleared.

TOTAL (CARRIED OVER TO SUMMARY CIVIL WORKS) 119,30,300.85

Digitally signed by

PRADYUMNA MUKHERJEE

SH-4: SH CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work upto plinth level.

6.1 4.1.8 1:4:8 (1 Cement:4coarse sand:8 graded stone aggregate 40 mm nominal size) cum 268.79 6,812.00 6,628.08 17,81,545.30

Providing and laying cement concrete in retaining walls, return walls, walls(any thickness) including

attached pilasters,columns, piers, parapets, coping, bedblocks, anchor blocks, plain window sills, fillets,

sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

7.1 4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). cum 2.83 9,895.20 9,628.03 27,237.70

TOTAL OF CONCRETE WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 18,08,783.00

SH-5: SH REINFORCED CEMENT CONCRETE WORK

8 5.9 Centring and shuttering including strutting, propping etc. and removal of form for:

a) 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 2,057.40 842.50 819.75 16,86,561.58

Suspended floors, roofs,landings, balconies and access platform with water proof ply 12 mm thick

c) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 3,866.00 961.30 935.34 36,16,043.38

d) 5.9.7 Stairs, (excluding landings) except spiral-staircases. sqm 844.00 764.95 744.30 6,28,186.12

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping

9 5.11 etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every - -

additional height of 1 metre or part thereof (Plan area to be measured)

9.1 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 2,743.06 384.30 373.92 10,25,694.95

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

10.1 5.22.6 Thermo-Mechanically Treated bars kilogram 5,16,702.00 107.85 104.94 542,21,700.31

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete above plinth level.

11.1 5.22A.6 Thermo-Mechanically Treated bars kilogram 6,86,850.000 107.85 104.94 720,76,699.64

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of

centering, shuttering, finishing and reinforcement - All work upto plinth level.

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20

mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses,

plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. up to floor five

13 5.2 level,excluding cost of centering, shuttering, finishing and reinforcement : - -

13.1 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) cum 264.03 10,852.95 10,559.92 27,88,167.45

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete to site of laying, curing, carriage

14 5.33 for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction - -

of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 110% of the specified minimum

cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra

14.1 5.33.1 All works upto plinth level - -

14.1.1 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 1,994.6 9,655.70 9,395.00 187,38,914.42

14.1.2 5.33.1.3 Concrete of M35 grade with minimum cement content of 370 kg /cum cum - 9,806.70 9,541.92 -

14.1.3 5.33.1.5 Concrete of M50 grade with minimum cement content of 410 kg /cum cum 1,339.00 10,108.65 9,835.72 131,70,024.33

14.2 5.37.2 All works above plinth level upto floor V level - -

14.2.1 5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 1,852.00 10,011.35 9,741.04 180,40,412.65

14.2.2 5.33.2.3 Concrete of M35 grade with minimum cement content of 370 kg /cum cum 2,050.00 10,162.35 9,887.97 202,70,331.43

14.2.3 5.33.2.5 Concrete of M50 grade with minimum cement content of 410 kg /cum cum 491.48 10,464.30 10,181.76 50,04,109.14

15 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. cum 938.71 355.65 346.05 3,24,837.71

Constructing cast-in situ RCC diaphragm wall by providing and laying machine batched, machine

mixed, self compacting, ready mix reinforced cement concrete, tramie controlled, of M-30 grade using

minimum 400 kg. cement per cum of concrete including providing and mixing required admixtures in

recommended proportions as per IS : 9103, as approved by the Engineer-in-charge, for achieving 150-

200mm slump, for diaphragm wall having thickness as per approved structural design not exceeding

600 mm, in pannels of required depth and lengths as per approved drawing, including constructing

16 5.49 necessary guide walls as required and as specified including boring in all kinds of soils and rocks, - -

including working in or under water and / or liquid mud, in foul conditions and pumping or bailing out of

water and removing slush, including disposal of earth/ rock / slush etc. for all leads and all lifts,

including preparing, providing and re-circulating bentonite slurry in the trench as and when required for

all depths, including agitating bentonite slurry during trenching etc., providing and fixing stop ends or

form tubes, upto the required depth of diaphragm wall including extracting the same after casting,

including chipping off the bentonite adulterated concrete or unsound concrete up to the cut off level for

obtaining the sound concrete, dressing undulations on the exposed face of diaphragm wall after

excavation by chipping / chiseling etc. including filling the depression/ cavities with sound concrete etc.

complete and as directed by the Engineer-in-charge, including providing recess for bearing plates and

fixing insert boxes for inclined rock anchors etc. complete as per the specifications and approved

design and as directed by the Engineer-in-charge, but excluding the cost of reinforcement and inserts.

(rates include cost of all inputs of labour, material and T & P, cost of handling, lifting & placing in

position the reinforcement cage in the trench, including the additional cost of welding the reinforcement

bars etc. involved in the work and all other incidental expenditure for completing the work as directed by

the Engineer-in-charge), However, the actual area of the diaphragm wall, correct to two places of

decimal, from design bottom level to the design cut off level (including portion anchored in the rock upto

the design bottom level) only shall be measured for payment.

Digitally signed by

PRADYUMNA MUKHERJEE

“Excess/less cement used for design mix including the extra cement required for under water

concreting is payable / recoverable separately

TOTAL OF R.C.C WORKS CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-6: SH BRICK WORK

Providing and laying autoclaved aerated cement blocks masonry with 150mm/200mm/300 mm thick

AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel

17 6.47 level with approved block laying polymer modified adhesive mortar all complete as per direction of cum 1,488.48 8,333.65 8,108.64 120,69,544.95

Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately)

TOTAL OF BRICK WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-9: SH WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

framed and fixed in position :

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory

windows, including ISI marked stainless steel butt hinges of required size with necessary screws,

excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-

19.1 9.5.1 Second class teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for

doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside

grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to

Extra for providing ISI marked stainless steel butt hinges instead of MS pressed butt hinges bright

finished of required size with necessary screws.( Shutter area to be measured )

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and

priming coat on unexposed surface etc.

22.1 9.40.1 2nd class teak wood

Providing 40x5 mm flat iron hold fasts 40 cm. long including fixing to frame with 10 mm dia. Bolts,nuts

23 9.53 and wooden plugs and embedding in cement concrete block 30x10x15 cm. 1:3:6 mix ( 1 cement :3 each 867.00 228.85 222.67 1,93,055.80

coarse sand 6 graded stone aggregate 20 mm nominal size )

Providing and fixing bright finished brass towerbolts( barrel type ) with necessary screws etc. complete

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of

lever handles of approved quality with necessary screws etc. complete

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than

grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws

26 9.96 etc. complete : - -

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade

AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.

27 9.97 complete : - -

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC

10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.

Providing and fixing aluminium hanging floor door stoppers,ISI marked,anodizes,(anodic coating not

29 9.101 less than grade AC10 as per IS :1868) transparent or dyed to required colour and shade,with - -

necessary screws etc. complete

Providing and fixing aluminium casement stays,ISI marked,anodises ( anodic coating notless than

30 9.102 grade AC10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws each 6.00 71.50 69.57 417.42

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of

16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete

mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire

31 9.136 seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size metre 237.60 1,709.25 1,663.10 3,95,152.62

and make, including applying a coat of approved brand fire resistant primer etc.complete as per

direction of Engineer-in-charge (Dash fastener to be paid for separately).

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming

to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable

mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200

mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR

insulation material and fixing with necessary stainless steel ball bearing hinges of approved make,

including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-

in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm

screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including

applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I.

beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS

16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having

33 9.138 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of sqm 192.90 40,405.55 39,314.60 75,83,786.37

insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass

should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011

and accredits labs as per gitating bentonite slurry during trenching etc., providing and fixing stop ends

or form tubes, upto the required depth of diaphragm wall including ex

TOTAL OF WOOD WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-10: SH STEEL WORK

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S.

34 10.5 gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming

coat of approved steel primer.

34.1 10.5.1 Using M.S. angles 40x40x6 mm for diagonal braces. sqm 3.00 5,804.35 5,647.63 16,942.90

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked

together through their entire length and jointed together at the end by end locks mounted on

specially designed pipe shaft with brackets, side guides and arrangements for inside and outside

locking with push and pull operation complete including the cost of providing and fixing necessary

27.5cm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters.

35.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 7.92 3,653.20 3,554.56 28,152.14

36 10.7 Providing and fixing ball bearing for rolling shutters. each 6.00 492.35 479.06 2,874.34

Digitally signed by

PRADYUMNA MUKHERJEE

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

37.1 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area sqm 48.00 1,281.35 1,246.75 59,844.17

Extra for providing grilled rolling shutters manufactured out of 8 mm dia. MS bar instead of laths as per

design approved by Enginer-in-charge ( area of grill to be measured )

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc.as required

39.1 10.25.2 In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works kg 12,904.00 172.60 167.94 21,67,095.18

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

40 10.28 accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of kg 1,460.15 772.40 751.55 10,97,371.35

the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for

payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc).

TOTAL OF STEEL WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-11: SH FLOORING

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.

41 11.3 complete.

41.1 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 176.08 614.20 597.62 1,05,228.03

42 11.24 Extra for pre finished nosing in treads of steps of marble stone metre 1,388.00 719.90 700.46 9,72,242.23

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry

mixed with pigment to match the shade of the slab including rubbing and polishing complete with base

of cement mortar 1:4 (1 cement : 4 coarse sand):

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of

44 11.48 organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / - -

grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the

manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile

adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of

joints (Payment for grouting of joints to be made separately).

Size of Tile 800x800 mm

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and laying C.C.of mix M-25 with ready mixed concrete from batching plant. The ready mixed

concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally

finished by floating, brooming with wire brush etc. complete as per specifications and directions of

Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content

considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/

recoverable separately).

TOTAL OF FLOORING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-12: SH ROOFING

Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm

and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm

long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing

and finishing to a flush finish of tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both

sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with :

47.1 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board sqm 588.00 1,529.10 1,487.81 8,74,834.81

Fully Perforated Gypsum Plaster Board of size 1200 x2400x12.5 mm having approximate 15%

perforatedv area with perforation size and pattern as approved by Engineer -in -Charge and as per

manufactures specification with all 4 sides tapered and backed by accoustical tissue with NRC value

not less than 0.60

TOTAL OF ROOFING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-13: SH FINISHING

12 mm cement plaster of mix:

49 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :

Digitally signed by

PRADYUMNA MUKHERJEE

50 13.16 6 mm cement plaster of mix

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to pepare the

surface even and smooth complete .

52 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm. over and including priming coat of exterior

primer applied @ 2.20 kg/10 sqm).

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less

than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever

required, to achieve even shade and colour

New wor (Two or more coats) over and including water thinnable priming coat with cement primer

having VOC content less than50 gram/ litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

54 13.83 Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than

50 grams/ litre

55.2 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre sqm 844.66 73.95 71.95 60,775.88

56 13.63 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

TOTAL OF FINISHING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-16: SH ROAD WORK

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The

ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process

and finally finished by floating, brooming with wire brush etc. complete as per specifications and

directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:-

Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix

is payable/ recoverable separately).

TOTAL OF ROAD WORKS CARRIED OVER TO SUMMARY OF CIVIL WORKS

SH-22: SH WATER PROOFING

Providing and laying integral cement based treatment for water proofing on horizontal surface at all

58 22.1 depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting

Digitally signed by

PRADYUMNA MUKHERJEE

(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base

of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to

IS:2645 in the recommended proportion over the leveling course (leveling course to be paid

separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing

compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm

thoroughly embedded in the 2nd layer

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing

specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound

conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone

slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing

compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20

mm thick with neat cement punning mixed with water proofing compound in recommended proportion

complete at all levels and as directed by Engineer-in-charge :

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions

of WC's,Kitchen and the like consisting of :

Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound confirming to

(i) IS 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 ( 1 cement :3 coarse sand ) mixed with water proofing

(ii) compound in recommended proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg.per sqm of area

IVth course of 400 micron thick PVC sheet( Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and laying integral cement based water proofing treatment including preparation of surface as

required for treatment of roofs,balconies,terrace etc. consisting of following operations.Applying a slurry

coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming

to IS. 2645 and approved by E-in- Charge over the RCC slab including adjoining walls up to 300 mm

height including cleaning the surface before treatment..Laying brick bats with mortar using broken

bricks/brick bats 25mm to 100mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and approved by E-in- Charge over

20mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and as approved by E-in Charge to required slope and treating

similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.After

61 22.7 two days of proper curing applying a second coat of cement slurry admixed with water proofing

compound conforming to IS : 2645.and approved by E-in-Charge.Finishing the surface with 20mm thick

jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by E-in -Charge including laying glass fibre cloth of approved

quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and

making of 300 x 300 mm square 3 mm deep.The whole terrace so finished shall be flooded with water

for a minimum period of two weeks for curing and for final test. All above operations to be done in order

and as directed and specified by the Engineer-in-Charge.

61.1 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 cms. sqm 689.43 1,684.60 1,639.12 11,30,055.61

TOTAL OF WATER PROOFING WORK CARRIED OVER TO SUMMARY OF CIVIL

SH-25: EXTERIOR FINISH (FAÇADE)

I) ACP CLADDING

Designing, fabricating, testing, installing and fixing in position Aluminium Composite Panel Cladding,

62 8.32 with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels

etc. including:

Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen

a) principle as required, proper drainage of water to make it watertight including checking of all the

structural and functional design.

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan

shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel

material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets

(each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar

500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face #

1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts,

washers, cleats, weather silicone sealant, backer rods etc.

Digitally signed by

PRADYUMNA MUKHERJEE

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and

serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of

approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to

perform as per specification and drawing The item includes cost of all material & labour component, the

cost of all mock ups at site, cost of all samples of the individual components for testing in an approved

laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding,

cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing

c) over of the building for occupation. Base frame work for ACP cladding is payable under the relevant sqm 238.31 5,015.05 4,879.64 11,62,867.88

aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding,

having all the performance characteristics all complete , as per the Architectural drawings, as per item

description, as specified, as per the approved shop drawings and as directed by the Engineer-in-

Charge. However, for the purpose of payment, only the actual area on the external face of the curtain

wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm.

up to two decimal places."

63 II) DHOLPUR STONE CLADDING

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine

cut edges sand stone ) on walls at all heights using MS square/rectangular tube in the required pattern

as per architectural drawing,including cost of cutting,welding etc..The frame work shall be fixed to the

wall with the help of MS brackets/lugs of angle iron /flats etc. which shall be welded to the frame and

embedded in the brick wall with cement concrete blocks 1:2:4 ( 1 cement :2 coarse sand :4 graded

stone aggregate 20 mm nominal size ) of size 300x230x300 mm including cost of necessary centering

and shuttering and with approved expansion hold fasteners on CC/RCC surface,including drilling

necessary holes.Approved cramps/pins shall be welded to the frame work to support stone cladding,the

steel work will be given a priming coat of zinc primer as approved by Engineer -in -Charge and painted

with two or more coats of epoxy paint.( Shop drawings shall be submitted by the contractor to the

engineer-in charge before execution). The frame work shall be fixed in true horizontal and vertical

lines/planes.( only structural steel frame work shall be measured for payment,stainles steel cramps

shall be paid for seperately and nothing extra shall be paid)

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone

Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired

pattern @ 43.04 kgs/10 sqm to form film of 11.5 mm thickness after scrapping and properly cleaning

the surface to remove loose particles from the plaster surface, followed by top coating with Premium

Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43

litres/10 sqm, complete as the direction of Engineer -in-Charge.

III) HIGH PRESSURE LAMINATE

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

65 9.127 finish with high density protective surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

VI) TEXTURED PAINT

Digitally signed by

PRADYUMNA MUKHERJEE

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior

primer applied @ 2.20kg/10 sqm

TOTAL OF EXTERIOR FINISH (FAÇADE) 24,77,457.08

BARRICADING WORK

Providing and erecting barricading for height above + 2.0 m and up to +12.0 m high at site and 2.0 m

platform alround the building to retain any material during dismantling/construction as per drawing

/direction of Engineer-In Charge including required signages etc complete consisting of following items

Providing and fixing pre-coated galvanised iron profile sheets (size, shape and pitch of corrugation as

approved by Engineer-incharge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120

grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the

sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns

minimum to avoid scratches during transportation and should be supplied in single length up to 12

metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping

screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape

wherever required. (Note :One time payment shall be made for providing barricading from start of work

till completion of work i/c shifting. The barricading provided shall remain to be the property of the

contractor on ion of the work). Vertical nd U value of 3.0 to 3.3 W/m2 K etc.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including

cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

(Note :- One time payment shall be made for providing barricading from start of work till completion of

work i/c shifting. The barricading provided shall remain to be the property of the contractor on

completion of the work after deducting salvage value of material through separate item)

Credit for salvage value of sheeting and structural steel of Item no. 2a and 2b (50% of total value)

TOTAL OF BARRICADING WORK 10,85,235.97

IV) GRC (Glass Reinforced Concrete)

Providing & Fixing Glass Reinforced Concrete (GRC) panels including all items required & as the

direction of Engineer -in-Charge.

V) STRUCTURE GLAZING

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of

67 NS2 structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights

and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads

conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure

without any failure), including functional design of the aluminum sections for fixing glazing panels of

a) various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts,

bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)cum-smoke

seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and

protection against fire hazard including:

Digitally signed by

PRADYUMNA MUKHERJEE

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of

required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving

perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel

framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent

bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and

in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone

sealant compatible with the structural silicone sealant of required bite size in a clean and controlled

c) factory / work shop environment , including double sided spacer tape, setting blocks and backer rod,

all of approved grade, brand and manufacture, as per the approved sealant design, within and all

around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and

d) profiles, as required as per the site conditions, to seal the gap between the building structure and all

its interfaces with curtain glazing to make it watertight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it

watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at

bottom (if required), making necessary holes of required sizes and of required numbers etc. complete.

This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium

grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc.,

enabling temporary structures and services, cranes or cradles etc. as described above and as

specified. The item includes the cost of getting all the structural and functional design including shop

e) drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also

includes the cost of all mock ups at site, cost of all samples of the individual components for testing in

an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning

and protection till the handing over of the building for occupation. In the end, the Contractor shall

provide a water tight structural glazing having all the performance characteristics etc. all complete as

required, as per the Architectural drawings, as per item description, as specified, as per the approved

shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section

capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall

be paid for separately under relevant items under this sub- head. However, for the purpose of payment,

only the actual area of structural glazing (including width of grooves ) on the external face shall be

measured in sqm. up to two decimal places.

Note:- 2. The following performance test are to be conducted on structural glazing system if area of

structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National

Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies,

India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of

testing on the basis of cost of the work, cost of the test and importance of the work. Performance

Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1) Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per

ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

2) Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range

3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range

Digitally signed by

PRADYUMNA MUKHERJEE

4) Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind

pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test.

Tests to be conducted on site.

6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 m

7) Openable Insert Vent (Top Hung)

System: AWS 48.NI

Design, Fabricate, deliver (to job site) and install Non-insulated all glass look insert unit as Outward

open able projected top-hung window system AWS 48.NI from Schueco India Solar & Windows Pvt.

Ltd. or equivalent. The system should be seamlessly integerated with Troptec SC 50.NI Façade system

from Schueco or Equivalent. All aluminium profiles should be made of Aluminium Alloy 6063 T6 with

Vent frame(shutter) basic depth of 48mm & minimum vent face width of 29 mm. The system should

withstand upto a wind load of 1.75 kPa. Without any performance failure. The system should

accommodate upto 32mm DGU . All gaskets to be EPDM. The system should have already been

tested/accredited by an international independent testing laboratory. The system should comply with an

Air infiltration requirement of ±600 Pa when tested in accordance with EN 12207. The system should

comply with an water tightness requirement of ±720 Pa when tested in accordance with EN 12211. The

system should also comply with a proof load of ±2.5kPa (1.5 times design wind load). The Friction stay

& Handle operations must be tested for durability –minimum of 20,000 cycles. Heavy duty friction stays

with opening angle upto 40 ° angle should be used. Handles to be fitted with fully concealed fittings with

no visible fixing screws. Locking technology with Single point or Multi-point depending upon the tested

criteria is acceptable. Where multi-point locking is required due to testing parameter, demonstration on

maintenance and serviceability is required. All exposed profiles should be powder coated to a minimum

8) Openable Insert Vent (Parallel Pop-Out)

Digitally signed by

PRADYUMNA MUKHERJEE

Thermally insulated, aluminium, parallel-opening window, with non-stepped insulating glass and UV-

resistant edge seal, bonding at glass position 4

For use in mullion/transom constructions with external cover caps, horizontal and vertical, or with

vertical cover caps only or horizontal cover caps only.

Due to bonding on position 4 of the insulating glass with the vent frame, project-specific approval is

required to bring the product onto the market. National regulations must be observed.

Design features:

The parallel-opening units consist of a thermally broken insert outer frame with a room-side face width

of 31 mm and a vent frame with a face width of 20 mm, for motorised or manual operation.

The basic depth of the vent frames is 93 mm (adhesive surface outside up to inside edge of vent).

The insert outer frame has a plastic profile attached on the outside with a variable supplementary

profile depending on the situation.

The top supplementary profile has a soft fin.

The insert units must be fitted with three continuous rebate gaskets.

The vent frames are glazed in the factory with insulating glass.

The side edge of the insulating glass is covered on all sides by a plastic glass frame profile.

Select follow-on text in accordance with the legal provisions.

If units with an installation height > 8 metres are designed, the glazing must also be mechanically

secured by means of a glass retention frame.

9) Glass for Vision Area

Coloured Insulated glass (6 mm SKN 144 II performance glass +12 mm air gap +6 mm clear Toughned

glass) having properties as visible Light transmittance (VLT) of 22%, Light reflection internal 29%, light

reflection external 21 %, shading coefficient (0.25- 0.28) and U value of 5.6 W/m2 degree K etc.

10) Spandrel Panel

Extra Over for Item-A, Providing & fixing Glass wool of approved make 50mm Thk. (Density : 48 Kg. /

M3) insulation of approved sample / make with Woven Fabric Black veil enclosed in a 1 mm thk G.I.

back pan with SS 304 hardware. All taxes applicable shall be extra.6mm single toughened/HS tinted

shade matching with vision glass, or as per architect/engineer in charge choice

Quote extra over on item (a.1) for providing and fixing the the fire stop for 2 hr Fire rating with smoke

seal at all floor slab levels required as per local fire authority. 100mm thickness & 100 Kg/m3 density of

Rockwool slab with 1.2mm GI flashing to hold the assembly shall be fixed in compressed form between

the gap of Building RCC and Curtain wall system at floor level. The whole assembly also to act as

acoustic assembly between the floors. The fire stop assembly shall run vertical side where there is a

shear wall condition or break in horizontal fire stop. The floor closure shall be provided continuously at

floor level with 1mm thk GI flashing closing gap between transom and building line with minimum of

10mm gap filled with smoke seal intumescent.

12) Single Glass for spandral

6mm thick ST series toughened glass of approved colour and shade matching with vision panel

Credit for Surplus excavated earth/ rock removed by contractor from the site for his own use or sale.

Digitally signed by

PRADYUMNA MUKHERJEE

Total Surplus earth available after back filling will be measured in this item. cum 16,807.00 (69.69) -11,71,279.83

72 NS4 Post-tensioning work for roof slab including designing, providing & fixing all complete MT 42.60 2,07,641.00 88,45,506.60

73 NS5 Full Height Partitions

Providing Full Height partition which shall be a modular system with overall thickness of 75mm for

creating rooms/spaces and enclosures of varying sizes and offer multiple elevations incorporating

together functional and decorative finishes. The system also shall offers features and options of doors,

shelf and worktop fixing while having provisions for mounting of accessories like motorized blinds,

access control. The offering shall include both single and double glazed partition. Main Frame

Structure: Main structure shall be a combination of different Aluminum Sections made from Aluminum

alloy 63400-WP and shall be powder coated with Epoxy Polyester or Anodized, varying in heights and

widths to make a full height cabin up to 3000 mm below the false ceiling level. The frame structure shall

be made by joining Aluminium Extrusions by means of brackets made of 3 mm Thk HR (IS-2062) and

screws. Overall thickness of panel assembly shall be 66 mm. In elevations, the width of tiles shall vary

from 300mm to 2400mm in pitch of 150mm and heights shall vary from 600 mm to 2400 mm (actual

534 mm to 2136 mm) in pitch of 600 mm. The system shall provide to make junctions straight partition

panels as per approved layout. The super structure above false ceiling level shall consist of True ceiling

mounting bracket which shall hold wooden batten frame work made from Rubber wood (50x50xlength

of partition). The partition panel extrusions shall be grouted to this superstructure. The system shall

have provision for leveling adjustment to compensate for floor unevenness ( up to 40 mm) as well as

false ceiling height difference(up to 15 mm). Provision shall be provided Horizontal adjustment at wall

side with adjustment up to 20 mm. Fabric Tile: Fabric Non-tack tiles shall be made of 9.0 mm thick PLB

/ PLT boards(IS: 12823:1990 ) edge banded with 0.5 mm thick PVC lipping, and upholstered with

approved fabric on front side. The overall thickness of tile shall be 10mm.

Digitally signed by

PRADYUMNA MUKHERJEE

Fabric Tackable tiles shall be made of 0.7mm thick GI Sheet (IS-277), with 8mm thick P.E. foam glued

to it on front side which are fabric upholstered on front side. The overall thickness of tile shall be 9 mm.

Stiffeners made of GI Sheet (IS-277) shall be provided at the back of the tile. White Board tile: Back

painted glass of 5 mm Shall be provided for glass finished writing board in the panel itself. Alternatively

regular wooden white board shall also be provided as per approved finishes. Wooden DL tiles: Wooden

DL tile of 9 mm thK PLB edge banded with 0.5 mm thk PVC lipping with approved design of laminate

shade shall be provided as per approved panel elevations. Glass Door With Hinges: Single side

opening Glass door shall be provided with Hinges, Lock with handle and Door Closer. The door shall be

made of 10mm Thk clear Toughened glass (IS-2835). Single Side Opening door shall have provision

for opening on LH side and RH side. Door Shutter Size shall be of 2200 x 956 mm. Doors shall of 1050

mm width and 2250 mm height only. Door including the frame width shall be of 1050mm. The full glass

panels shall range from 300 mm to 1200 mm max. Height of single panel of glass shall be up to 8’0”. sqft 38720.00 3,115.00 1206,12,800.00

Full height of panel shall be max up to 10’ with skirting ht shall be of 120 mm. Worktops for cabin

module shall be provided in opaque partitions and shall be of sizes – 1500, 1650 and 1800 mm width

and with 600/750 mm depth. Return worktop shall be of size 900mm – 1800 mm ( in pitch of 150 mm).

Provision of wire management through the panels vertically shall be possible. Wiring intake into the

panel from flooring as well as ceiling shall be provided. Provision in panel width up to 1200 mm width

for 2 slots of 100 x 25 at a distance of 100 mm from the edge of the panel shall be provided. Beyond

1200 mm to 2400 mm, the slots shall increase from 2 to 4 nos. the intermediate slots shall be

equidistance from the end slots. The end slots shall be same as the ones in the 1200 mm w panels.

Provision to provide wire management in full glazed panel in separate power post should be possible.

Digitally signed by

PRADYUMNA MUKHERJEE

74 NS6 Raised Access Floors with Homogeneous Antistatic/Esd 2 MM Vinyl

Factory finished 2 MM thick PVC Tile/Sheet Flooring conforming to EN ISO 24346 (EN 428) weighing

3300 gms/smt conforming to EN ISO 23997 (EN 430), European classification EN ISO 10874 (EN 685)

(Class 34-43); Fire Rating EN 13 501-1 (Bfl-s1); Static electrical propensity EN 1815 (kV < 2), Electrical

resistance EN 1081; Wear resistance conforming to EN 660.2; Dimensional stability conforming to EN

ISO 23999 (EN 434); Residual indentation conforming to EN ISO 24343-1 (EN 433); Thermal

Conductivity conforming to EN ISO 10456 (EN 12524); Colour Fastness conforming to EN 20 105-B 02;

Chemical Products fastness conforming to EN ISO 26987 (EN 423); TVOC after 28 days conforming to

ISO 16000-6 (µg/ m3 < 10) on Calcium Sulphate core panels, with 0,5 mm thick Hot Dip galvanised

steel tray on the bottom side in panel of size 600 x 600 mm in 34 mm thickness. Panel edges finished

with a 0,5 mm ABS edge. All panels shall be completely interchangeable and the raised access floor

surface shall support Concentrated Load of 4,2 kN placed on a 625 mm2 (using a square indentor)

anywhere on the panel with a maximum top surface deflection of 2,5 mm. (According to EN standard

12825) Panel shall not exceed a permanent set of 0,25 mm, after the load is removed. Panel shall be

capable of withstanding an Ultimate load of 7 kN applied onto a 625 mm2 area (using square

indentor) anywhere on the panel (According to EN Standard 12825). The raised floor surface

supported by U-shape, Clip-on Stringers of dimensions of 25 mm width by 30 mm height by 1 mm

thickness rolled formed out of Hot Dip galvanised steel and adjustable Pedestals, manufactured out of

steel of 2.5 mm thickness applied with corrosion resistance galvanisation finish, bottom & head plate of

dia 90 mm. Bottom plate screw fixed to 16 mm dia threaded rods and Head Plate mechanically fixed to

a steel tube, with a dia of 21 mm allowing various lengths for the correct height adjustment of the

pedestal. Stringers and Pedestal heads supported with black PVC washers, for sound deadening

TOTAL OF NS ITEMS CARRIED OVER TO SUMMARY OF CIVIL WORKS 1448,97,482.14

Digitally signed by

PRADYUMNA MUKHERJEE

COST SUMMARY OF PLUMBING WORKS

S. NO. DESCRIPTION AMOUNT ( NSR )

1 SANITARY FIXTURE & FITTINGS 20,81,862.23 7,57,209.96

2 SOIL, WASTE , VENT WATER PIPES 24,50,390.45 5,10,629.03

3 INTERNAL WATER SUPPLY 7,69,254.58 4,05,127.79

4 SEWERAGE & DRAINGE SYESTEM 40,679.72

5 PUMPS, WATER TREATMENT & ALIED EQUIPMENT 56,54,657.53

7 ELECTRICAL PANEL BOARDS FOR PHE WORKS. 4,48,856.93

8 RO SYSTEM 2,31,823.82

9 ROOF TOP SOLAR SYSTEM 88,846.97

10 HARVESTING PITS & TUBEWELL 6,79,068.40 -

11 LANDSCAPE IRRIGATION SYSTEM 5,320.70 47,453.52

TOTAL ( DSR+NSR ) 141,71,181.64

Digitally signed by

PRADYUMNA MUKHERJEE

BOQ FOR PLUMBING & WATER SUPPLY WORKS

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

SECTION A- PLUMBING WORKS.

SUB HEAD I - SANITARY FIXTURE & FITTINGS

1.1 17.78 Providing and fixing white vitreous china extended wall mounted water closet of size 780X

370X690mm of approved shape including providing and fixing of white vitreous china cistern with dual

flushing fitting of flushing capacity 3 liter/6 liters (Adjustable to 4liter/8liters) including sheet cover , and

cistern fittings, nut bolt gasket etc complete.

1.2 17.7 Provinding and fixing was basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of

approved quality and make, including painting of fittings and brackets, cutting and making good the - -

walls whereever required :

17.7.4 White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer

1.3 17.5 Providing and fixing white vitreous china flat back half stall urinal of size 580 x 380x350 mm with white

P.V.C automatic flushing cistern, with fittings, standard size C.P brass flush pipe, spreaders with unions

and clamps (all in C.P brass) with waste fitting as per IS : 2556, C.I trap with outlet grating and other - -

coupling in C.P brass including painting of fittings and cutting and making good the walls and floors

whereever required

17.5.2 Range of two half stall urinals with 5 litre P.V.C automatic flushing cistern 11 11 Each 18,008.75 17,522.51 1,92,747.65

1.4 NSR 1 Providing & fixing chinaware urinal partition of 90X 320X 720 mm with fixed with expandable anchor

fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete

complete including cutting and making good the walls wherever required.

1.5 NSR 2 Providing and fixing 8mm thick beveled edge glass mirror with side polished complete including fixing

over marine plywood frame work with silicon at all levels & height including fixing of molded ,screw and 20 20 sqm 1,035.35 20,706.99

silicon etc. incl labors, tools, scaffolding at all heights as per Direction of EIC

1.6 17.31 Providing and fixig 600x450 mm beveled edge mirror of superior glass (of approved quality) complete

with 6 mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and washers 67 67 Each 1607.95 1,564.54 1,04,823.87

1.7 17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium

angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws,rawl plugs 23 23 Each 1083.50 1,054.25 24,247.65

1.8 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass

screws with concealed fittings arrangement of approved quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm,

weighing not less than 170 gms.

1.8 18.53 Providing and fixing CP brass angle valve for basin mixture and geyser points of approved quality

confirming to IS: 8931.

1.9 18.63 Providing and fixing PTMT angle stop cock 15mm nominal bore,weighting not less than 85gms.

1.10 17.70 Providing and fixing PTMT Bottle Trap for Wash basin. - -

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm

17.70.1 from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not 67 67 Each 367.10 357.19 23,931.62

less than 260 gms.

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

1.11 18.65 Providing & Fixing PTMT soap dish holder having legth of 138mm breadth 102mm height of 75mm

with concealed fittings arrangements ,weighing not less than 106 gms.

1.12 NSR 3 Providing and fixing CP brass single lever low flow Sink mixer with 15 mm CP brass single lever pillar

cock with pop up and waste complete including cutting and making good the walls where required. 3 3 Each 3,352.80 10,058.39

1.14 NSR 4 Providing , Fixing , testing and commissioning of CP Brass Shower Mixer with provision of overhead

shower in built spout, spout/shower selector with wall flange complete with all accessories as required 23 23 Each 4,593.34 1,05,646.75

and making good the walls wherever required.

1.15 NSR 5 Providing , Fixing, testing and commissioning of CP Brass 115mm long Shower Arm with wall flange

and pressure adjustable Shower Rose complete with all accessories as required and making good the 23 23 Each 1,242.83 28,585.10

walls wherever required.

1.17 Providing and fixing 8 mm dia C.P / S.S. Jet with flexible tube upto 1 meter long with S.S triangular plate

17.16 A to Eureopean type W.C of quality and make as approved by Engineer-in-charge 87 87 Each 349.15 339.72 29,555.90

1.18 NSR 6 Providing & fixing soild state no touch operating fully highgenic SS hand drier of best quality, to be

operated with 230 volts, single phase, with fully hygienic condition, with all accessories including cutting 32 32 Each 12,450.90 3,98,428.83

and making good the walls, wherever required.

1.19 NSR 7 Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory

supplied spring loaded seal guard with integral single mould sealing fins made of flexible EVA body,

including bush/adaptor for use with C.I. Pipe as supplied with the pan connector. 87 87 Each 293.00 25,491.00

1.20 NSR 8 Providing & fixing wall mounted 700mm Galvanised powder coated grab bar including cutting & making

good the walls. 10 10 Each 5,184.28 51,842.77

1.21 18.58 Providing and fixing PTMT grating of approved quality and colour. -

1.21.1 18.58.1 Circular/square type -

b) 18.58.1.2 125 mm nominal dia/size with 25 mm waste hole. 5 5 Each 51.85 50.45 252.25

1.22 NSR 9 Providing,Fixing satin finish stainless steel AISI 316 grade wall mounted coat hook on door complete.

1.24 17.10 Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per I.S.13983 with C.I. Brackets,

stainless steel plug 40mm including painting of fittings and brackets cutting and making good the walls -

wherever required.

a) 17.10.1 Kitchen sink with drain board -

b) 17.10.2 Kitchen sink without drain board - -

1.25 18.49 Providing & fixing C.P brass bib cock of approved quality conforming to IS :8931. - -

1.26 18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and

weighing not less than 690 gms.

1.27 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions : - -

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

1.28 NSR 10 Providing, Installing & fixing storage type water heater of approved shade with copper container,

glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon

lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & -

outlet suitable for working pressure of 8 kg/sqcm complete as required.

a) Capacity 25 litres 1 1 Each 7904.81 7,904.81

1.29 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from

wall of standard shape with bracket of the same materials with snap fittings of approved quality and 32 32 Each 168.35 163.80 5,241.75

colour, weighing not less than 105 gms.

1.30 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum

distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,

weighing not less than 88 gms.

TOTAL OF SUB HEAD I - SANITARY FIXTURES 20,81,862.23 7,57,209.96

SUB HEAD II - SOIL, WASTE , VENT WATER PIPES

2.01 17.35 Providing and fixing soil, waste and vent pipes

17.35.1.2 Centrifugally cast (spun) iron socket & Spigot (S & S) Pipe as per IS 3989 900 900 Metre 1,180.75 1,148.87 10,33,982.78

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS 3989 50 50 Metre 1,186.00 1,153.98 57,698.90

17.37 Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe

embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good

2.03 17.39 Providing and fixing plain bend of required degree. - -

2.04 17.44 Providing and fixing single equal plain junction of required degree . - -

2.05 17.56 Providing and fixing terminal guard. - -

17.56.2.2 sand cast iron S & S as per IS: 3989 1 1 Each 404.75 393.82 393.82

2.06 17.58 Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of

2.07 17.60 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without

vent arm complete, including cost of cutting and making good the walls and floors.

17.60.1 100mm inlet and 100mm outlet - -

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

2.08 18.10 Providing & fixing GI pipes complete with GI fittings and clamps, including cutting & making good the

Internal work- Exposed on wall - -

2.09 18.40 Painting GI pipes and fittings with two coats of anti corrosive bitumestic paint of approved quality.

2.10 17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of

synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of - -

approved quality) for new work

2.11 17.52 Providing and fixing single unequal plain invert branch of required degree : - -

2.12 12.41 Providing and fixing on wall face unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,

including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) - -

Single socketed pipes.

2.13 Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised-

PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS:

5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

a) Single Tee with door

c) Bend 87.5 degree

f) NSR 14 110mm diameter. 4 4 Each 135.58 542.33

2.14 12.22 Making khurras 45x45 cm. with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size) over PVC sheet1mx1mx400 micron,

finished with12 mm cement plaster1:3 (1 cement : 3 coarse sand) and a coat of neat cement,

roundingthe edges and making and finishingthe outlet complete

2.16 NSR 15 Providing and fixing 100mm dia G.I. inlet fitting consisting of 100mm dia main G.I pipe with multiple G.I.

sockets (Inlets) of required diameter welded to it (as per site requirement) and fixing the same to C.I

trap and setting in cement concrete, complete as per instructions of the Engineer in charge.

2.17 NSR 16 Providing and fixing G.I reducer/hopper/elbow (Floor Drain) of 100 x 75mm, complete as per

instructions of the Engineer in charge.(grating and G.I pipe to be paid separately)

2.18 NSR 17 Providing and fixing cast brass Floor Clean Out plug with suitable insert keys for opening, male

threaded joint with G.I. socket lead caulked to soil pipe / waste pipe of C.I. and C.I.(LA) pipe as required 60 60 Each 1,398.95 83,937.27

complete as per instruction of the Engineer in charge.

2.19 NSR 18 Providing and fixing soil waste and vent pipes

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

150 mm dia centrifugally cast (spun) iron Socket & Spigot (S&S) pipe as per IS:3989. 50 50 Meter 1,692.71 84,635.72

2.20 NSR 19 Providing and fixing plain bend of required degree:

150mm Sand cast iron S&S as per IS:3989. 2 2 Each 1,047.68 2,095.35

2.21 NSR 20 Providing and fixing single equal plain junction of required degree.

150 x 150 x 150mm Sand cast iron S&S as per IS:3989 2 2 Each 1,084.65 2,169.30

2.22 NSR 21 Providing and fixing single unequal plain junction of required degree.

150 x 150 x 100mm Sand cast iron S&S As per IS: 3989 2 2 Each 922.37 1,844.73

2.23 NSR 22 Providing and fixing terminal guard

150mm Sand cast iron S&S as per IS: 3989. 2 2 Each 1,296.24 2,592.48

2.24 NSR 23 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipe of

2.25 NSR 24 Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any

colour such as chocolate, grey or buff, etc., over a coat of primer (of approved quality) for new work.

150mm diameter pipe 50 50 Metre 292.73 14,636.64

TOTAL OF SUB HEAD II - SOIL,WASTE & VENT WATER PIPES 24,50,390.45 5,10,629.03

SUB HEAD III - INTERNAL WATER SUPPLY

3.01 18.10 Providing & fixing GI pipes complete with GI fittings and clamps, including cutting & making good the

Internal work- Exposed on wall

g) NSR 25 65mm nominal bore 20 20 Metre 1,084.65 21,693.04

h) NSR 26 80mm nominal bore 30 30 Metre 1,312.68 39,380.26

i) NSR 27 100mm nominal bore 80 80 Metre 1,491.40 1,19,311.72

3.02 18.8 Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes hyaving thermal stability for hot

&coldwater supply, including all CPVC plain & brass threaded fitting, including fixing the pipewith

clampsat 1 m spacing. This includesjointing of pipes &fittingwith one step CPVC solvent cement and

cost ofcutting chases and making good the same including testing ofjoints complete as per direction

ofEngineer in Charge.

Concealed work including cutting chases and making good the walls etc.

a) 18.8.1 15mm nominal outer dia. Pipes. 150 150 Metre 497.80 484.36 72,653.91

b) 18.8.2 20mm nominal outer dia. Pipes. 600 600 Metre 537.60 523.08 3,13,850.88

c) 18.8.3 25mm nominal outer dia. Pipes. 15 15 Metre 627.25 610.31 9,154.71

d) 18.8.4 32mm nominal outer dia. Pipes. 5 5 Metre 739.30 719.34 3,596.69

3.03 18.12 Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc. - -

3.04 18.16 Providing & fixing brass stop cock of approved quality . - -

3.05 18.17 Providing and fixing gunmetal gate valve withCI wheel of approved quality (Screwed end) - -

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

g) NSR 28 100mm nominal bore 5 5 Each 3,333.05 16,665.23

3.06 18.32.1 Constructing masonary chamber 30x30x50cm, inside with 7.5 class designation brick work in cement

mortar 1:4 (1 cement : 4 coarse sand) for stop cock with C.I. Surface box 100x100x75 mm ( inside)

with hinged cover fixed in cement concrete slab 1:2:4 (1 cement:2 coarse sand:4 graded stone

aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement:5 fine sand: 1 1 Each 1,992.60 1,938.80 1,938.80

10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement

: 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard

design with F.P.S. bricks.

3.07 18.38 Painting GI pipes and fittings with synthetic enamel white paint with two coats over a ready mixed

priming coat, both of approved quality for new work.

g) NSR 29 65mm dia nominal bore 20 20 Metre 52.38 1,047.68

h) NSR 30 80mm dia nominal bore 30 30 Metre 60.60 1,818.02

i) NSR 31 100mm dia nominal bore 80 80 Metre 61.63 4,930.24

3.08 18.40 Painting GI pipes and fittings with two coats of anti corrosive bitumestic paint of approved quality.

3.09 18.41 Providing and filling sand of grading zone V or coarser grade alround the GI pipes in external work.

3.10 18.59 Providing & fixing C.I double air valve of approved quality with bolts , nuts , rubber insertion etc

complete (The tail pieces , tapers etc if required will be paid separately )

3.11 Installing & fixing cast-iron manhole cover and frame suitable for 600mm dia manhole with lockable and

lifting arrangement. The entire iterm shal be epoxy coated and approved by insecticide department

a) NSR 32 Medium duty double seal of size 560 mm dia and total weight of cover & frame to be not less than 116

KG. (Location : U/G Water Tanks Top)

b) NSR 33 Light duty double seal of size 560 mm dia and total weight of cover & frame to be not less than 116 KG.

(Location : O/H Water Tanks Top)

3.12 NSR 34 Providing and fixing M.S fabricated hot dipped galvinised coating puddle flange comprising of 600 mm

dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm

thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making

welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement

bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of

following diameter. (Location: underground/ overhead tanks.)

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

3.13 19.16 Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910

on12mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and

over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude

legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate

anchoring projections on tail length on 138mm as per standard drawing and suitable to with dtand the 10 10 Each 553.70 538.75 5,387.50

bend test and chemical resistance test as per specifications and having manufacture's permanent

identification make to be visible even after fixing, including fixing in manholes with 30x20x15cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

complete as per design.

3.14 Supply and install pressure regulating station for cold water supply comprising of 1 no gun metal ball

valves on, 1 no.inlet/outlet and bye-pass and 1 no. PRV unit (diaphram type) with flanged connection, 2

nos pressure gauge on inlet and outlet, 1no 15 mm dia safety valve. The complete system is tested to a

pressure not less than 3.0 kg/cm2 and suitable to reduce the pressure as desired including

flanges/unions, nuts, bolts and washers complete as required for application. (horizontal or vertical as

3.15 Providing, Fixing, Testing & Commissioning of nitrle rubber insulation on hot water supply pipes. K-Flex,

A-Flex, Armacell

NSR-44 32mm dia (9 mm thickness) 45 45 Metre 208.51 9382.86

NSR-45 40mm dia (13 mm thickness) 15 15 Metre 232.13 3481.98

NSR-46 50mm dia (13 mm thickness) 15 15 Metre 250.62 3759.31

TOTAL OF SUB HEAD III - INTERNAL WATER SUPPLY 7,69,254.58 4,05,127.79

SUB HEAD IV - SEWERAGE & DRAINGE SYESTEM

4.09 19.27 Constructing brick masonary road gully chamber 50x45x60 cm with bricks of class designation 7.5 in

cement mortar 1:4 (1 cement :4 coarse sand ) including 500x450 mm precast RCC horizontal grating

with frame complete as per standard design .

4.15 19.4 Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber

with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the

weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. - -

(COVER MIN. 4.5 KG & FRAME MIN.2.7 KG )

19.4.3.1 180x150mm size P type With FPS bricks 4 4 Each 2,802.15 2,726.49 10,905.97

4.16 19.21 Making connection of drain or sewer line with existing manhole including breaking into and manhole

good the wall, floors with cement concrete 1:2:4 mix ( 1 Cement : 2 Coarse Sand : 4 Graded Stone

Aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 - -

Coarse sand), finishedwitha floating coat of neat ement and making necessary channels for the drain

etc, complete: .

a) 19.21.1 For pipe 100 to 250 mm diameter 1 1 Each 810.45 788.57 788.57

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

TOTAL OF SUB HEAD IV - SEWERAGE & DRAINAGE SYSTEM 40,679.72 -

SUB HEAD V -.PUMPS, & ALIED EQUIPMENTS

5.01 NSR Domestic Water Pump.

Providing, fixing and testing of packaged fixed drive type skid mounted hydropneumatic system

comprising of :-

Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304

impellers with stainless steel SS-316L shaft as per IEC standards and GJL250 cast iron suction &

discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for

400/440 Volts, 3 phase, 50 Hz A.C. supply No. of Pumps: 3 (2 Working +1 Standby)=1 set

Control Panel with programmable logic controller (PLC) for cyclic operation of pumps. Pump working

sequence should change after every operation.Contractor overload relays and MCBs should confirm to

IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply

should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist

of cooling fan.

Pressure switches bellow type fitted with micro switch and having maximum pressure and

differential scale should confirming BS-6134 standards and IP55 protection class. Solonoid valve at

terrace tank for start stop.

Stainless steel suction and delevery header, ball valve on each pump on section delivery side, non

return valves, Y stainer complete in all respect.

Ball valves to be used should be Hot Pressed brass OT-58 with stainless steel ball and P.T.F.E seal

and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall follow following duty.

A NSR 47 For Domestic Water Supply

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity : app. 125 lpm

B NSR 48 For Flushing Water Supply

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity : app. 125 lpm

C NSR 49 Water Make up Pump to STP & Irrigation Pumps

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity : app. 200 lpm

5.02 Drainage Sump Pumps

Submersible pumps for basement drainage & Pump Room drainage.

NSR Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller

connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level

controllers, auto control, sequential change over facility with one proper working at low level & two

proper working at high level with an audible alarm including all interconnectivity cables, with both pumps

connected to common outlet header including valves, non return valves, lifting chains etc. complete in

No. of Pumps: 2 (1 Working +1 Standby)=1 set

A NSR 50 For Basement Drainage

(Solid handiling capacity 12mm)

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

Capacity- 300 lpm (Each)

B NSR 51 For Pump Room Drainage

(Solid handiling capacity 12mm)

Capacity- 200 lpm (Each)

3.15 NSR Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted

Hydropneumatic System As Follows:(A) Vertical, In-Line, Multisage, centrifugal pumps with SS-304

casing and impeller and SS-316 shaft, CI base & head CI material shouldbe CED coated TEFC motor

(with mechanical seal) with single VFD suitable for automatic operation and delivering the specified

discharge at the specified head,VFD should be of class IP-20 with pressure vessel, pressure vessel

should be matching of specied requirement of pump.(B) b. External Pump mounted or wall mounted

microprocessor PID controller and frequency inverter integrated in a single body or as separate

components with pressure sensor transmitter minimum two lined LCD display, diodes to indicate pump

ready, pump running and fault and capable to communicate with other controllers following MODBUS-

RTU or BACNET Class-2 protocall through RS485 port. System should be capable to compensate for

frictional losses at lower flows. All alarms should be displayed in the controller. System should be

equiped with dry running protection. ( C) Complete (Skid mounted wall mounted / floor mounted)

electrical control panel comprising of all accessories such as PLCs, pressure switches, pressure

transducers, control wiring and any other necessary imports etc. (list to be provided by the vendor)

(D)Precharged diaphram pressure vessel with food grade membrane, charging connection, connected

to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc complete.(E)Set of

accessories such as pressure switches, pressure transducers, inter connecting power and control

cabling etc. complete(F) Accessories like pressure gauge, MS base frame (Synthetic enamel painted

over a coat of primer)(G) GI suction and delivery header with flanges for inlet connection, common

outlet header with flanges for outlet connections as required, and inter connecting piping with flexible

connections, eccentric type reducers etc. all necessary indigenous accessories like valves, strainer &

NRV as required to complete the installation.

NSR 52 Domestic Water booster Pumps at Terrace 1 1 Each 1,65,368.34 1,65,368.34

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 200 LPM

HP 2.5 HP ( Approx.).

5.03 For Water level indicators with following details:

Underground tanks

A NSR 53 Minimum 4 level Multi level indicators with magnetic type sensor probes complete. 1 1 Each 15,252.92 15,252.92

B NSR 54 Minimum 4 level Multi level indicators with magnetic type sensor probes complete. 2 2 Each 16,793.62 33,587.24

5.04 NSR Providing, fixing and testing of factory fitted packaged type skid mounted pumping system comprising of

Horizontal inline centrifugal pumping set with CI casing and SS-304 impellers with stainless steel SS-

316L shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to

a) TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C.

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

Motor Control Panel with DOL starter MCB and controller for cyclic operation of pumps. Pump working

sequence should change after every operation.Contractor overload relays and MCBs should confirm to

IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply

b) should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist

of cooling fan and liquid level controller with controll wiring from UG tank to UG tank with float switch for

contrlloing cut-off and cut-in of pumps and dry run protection complete in all respects.

Suction and delivery header with Ball valves Hot Pressed brass OT-58 with stainless steel ball and

c) P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall follow following duty.

5.04.1 NSR 55 Filter Feed Pump

No. of Pumps: 3(2Working + 1 Stand by )

Capacity : 100 lpm

5.05 NSR Providing and fixing vertical pressure filter with dual media filter (comprising of 600mm bed depth of

graded sand gravel and 600mm bed depth of Anthracite) fabricated from high performance M.S plate

of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings

including top and bottom hub and lateral distribution and collection system complete with initial charge of

filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to

Discharge : 100 lpm

Filtration Rate : 15000 lit./m 2/h

Suggested dia app. : 0.60 m 1 1 Each 2,79,893.63 2,79,893.63

5.06 NSR 57 Activated carbon Filter (Domestic Water)

Providing and fixing vertical activated carbon filter comprising of activated carbon filter media

fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished

ends with top and bottom flanged openings including top and bottom hub and lateral distribution and

collection system complete with initial charge of filter media, face piping, valves, accessories, Epoxy

painting, testing and commissioning complete.(Tested to 6 Kg/m 2)

Discharge : 100 lpm

Filtration Rate : 15000 lit./m 2/h

Suggested dia app. : 0.60 m 1 1 Each 2,87,802.55 2,87,802.55

5.07 NSR Providing, fixing, testing & commissioning of MSEP water softening plant (suitable for 3 Kg/Sqcm

working pressure) complete with initial charge with T-40 NA Resin, multiport valve with built in ejector

for controlling all operations), regeneration system and HDPE tank, pressure gauge at inlet, outlet and

back wash (each with isolation cock), valves, fittings and water hardness testing kit & associated

works. Softener shall be suitable for the following duty:

5.07.1 Note:The successful contractor will have to carry out a test of raw water from all the sources of water

for the Commercial, Residential & apartment at their own cost from a reputed lab as approved by the

Engineer-in-Charge / Consultant. On the basis of these results the contractor has to submit his shop

drawings, design calculations and specifications accordingly.

Please note that it is ultimately the responsibility of the contractor to provide treated water for different

use as per International Standard as given in the attached guidelines.

5.07.1 NSR 58 Raw water hardness 500 Mg/L

Treated water hardness 100 Mg/L

Regeneration Period 12 Hrs.

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

5.09 NSR 59 Supplying, installing, testing and commissioning of dosing system (for domestic water treatment plant)

consisting of one HDPE tank of 100 litres capacity with a positive displacement diphragm dosing pump

having variable flowrate of 0-6 lph. The motor shall be suitable for operation at 240 V / single phase/50

Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, valves, 1 1 Set 45,707.40 45,707.40

strainers, low level switch and injection fittings. The pump shall be speed & stroke control .

The cost shall be inclusive of providing salt for the testing and operation of system before handover to

5.10 NSR 60 Supplying, installing, testing and commissioning of annunciation and indication panel with interlocking

arrangement complete in accordance to specification for level controller etc with control cabling from 1 1 Each 37,952.55 37,952.55

field to MCC as required.

The system shall be complete to ensure automatic operation of pump in accordance to water level in

respective tanks.

5.11 NSR 61 Providing & fixing level controllers for water pumps to start/stop the pump at set level. Including wiring,

cabling from pump to panel & all other accessories as required to operate the system automatically. 1 1 Each 76,110.52 76,110.52

5.12 NSR 62 Providing & fixing pressure switch for water pumps to start/stop the filter feed pump at set pressure.

Including wiring, cabling from pump to panel & all other accessories as required to operate the system 1 1 Each 15,098.85 15,098.85

5.13 NSR 63 Supply, installation, testing and commissioning of tanker inlet connection complete with 100 mm dia GI

(heavy) inlet piping, hose inlet connection, MS cabinet enclosure (epoxy painted after fabriction), pad

locking arrangement, inlet flexible hose complete with all necessary arrangement.

5.14 NSR Providing & fixing butterfly valve Rated for PN16 pressure rating. Including rubber gasket, flanges,

nuts, bolts, washers & painting complete as required.

5.15 NSR 69 Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet

basket with necessary flange/ unions nuts, bolts and washers complete as required (on pump suction).

5.16 NSR Providing & fixing dual plate CI wafer type check valve tested to a pressure of 15 Kg/sqcm. Including

rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

5.17 NSR Providing and fixing Heavy class GI pipe (IS 1239 up to 150 mm dia. and IS3589 6.35 mm thickness

above 150 mm dia.)header complete for pump suction / discharge manifold comprising of flanges,

unions, check nuts, tee elbow etc. including all flanged connections as per drawing / site requirement.

Supports from wall, floor and ceiling etc. Including dead end flanged connection complete as required.

The header size shall also include tee connections with blank flanges for the future connections. two

coats of synthetic enamel paint of approved shade as per IS : 2379 pipe colour code

5.18 NSR 76 Providing & fixing neoprene rubber double flanged rubber expansion joint (anti vibration bellow) of

standard length as per manufacturers specifications. suitable for hydrostatic test pressure of 15

kg/sqcm including all necessary fittings i.e. rubber gasket, nuts, bolts, washers etc complete as

5.20 NSR Providing & fixing brass ball valve with CW617N grade brass with hard chrome plated ball inside PTFE

(Teflon) seat & ring with chrome plated centre handle with female BSP threads tested to a pressure not

less than 15 Kg / sqcm complete:in all respects.

TOTAL OF SUB HEAD V - PUMPS & ALIED EQUIPMENTS - 56,54,657.53

SUB HEAD VII -ELECTRICAL PANEL BOARDS FOR PHE WORKS.

7.1 NSR 81 CUBICAL PANEL BOARD - PLUMBING

i) For 2 x 3.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1 stand by) 1 1 Item 4,48,856.93 4,48,856.93

ii) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)

Supply, installation, testing and commissioning of Cubical type sectionalised floor standing switch board

of 31 MVA fault capacity at 415 V complete with 3.5 strip, 160 A capacity Aluminium Bus - Bar

Electrolytic grade, cable alley, switchgears of following capacity & as per specifications.

100 A TP MCCB with heavy duty solid neutral link with (0-100A) ammeter with 3 CT and selector switch,

(0 - 500 V) voltmeter with selector switch, phase indication light with protection fuse. - 01 Set

i) i) For 2 x 3.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1 stand by)

II) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)

40 A TP MCB with 40 A DOL starter, overload relay, 96 mm (0-40A) ammeter with single CT, start /

stop push buttons, on / off / trip indication lights with protection fuse, single phase preventer. - 01 set.

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

25 A TP MCB with 25 A DOL starter, overload relay, 96 mm (0-25A) ammeter with single CT, start /

stop push buttons, on / off / trip indication lights with protection fuse, single phase preventer. - 01 set.

TOTAL OF SUB HEADVII - ELECTRICAL PANEL BOARDS. - 4,48,856.93

SUB HEAD VIII RO SYSTEM

Supplying, lifting at the terrace, assembly, erection, testing and commissioning of RO Water treatment

system including centalised water cooler for cold water provided all its components of required size as

per water test analysis to make the water suitable for drinking, complete including the following as

mentioned below. The cost will include testing of permeate water sample from a CPCB approved test

laboratory, generating and providing membrane analysis data form the licensed manufacturer's software

Permeate water quantity = 200 lit/hr.

Minimum Recovery = 70%-75%

Raw Water Characteristics - As per Water Test Analysis Report of Shriram Test Laboratory to be got

done by the supplier

Raw water Quality

Total Dissolved Solids: < 990 PPM

Turbidity : <1NTU

Chlorides : 205 ppm

Sulphates : 105 ppm

Treated Water Quality

Turbidity : <1NTU

Chlorides : < 10 ppm

Sulphates : < 5 ppm

a SS Vertical centrifugal Raw Water Pump (1 Working + 1 Stand-by)

b FRP Dual Media Filter

c Activated Carbon Filter

c Antiscalant Dosing System including pump chemical dosing pump, tanks etc.

d Polypropylene Micron/cartridge Filter and SS housing

e Stainless steel vertical multistage inline high pressure pump (1 Working) including dry running protection

f Spirally wounded 6 nos. of RO Membranes

g Composite FRP RO pressure tube/vessel

h Automatic RO Module Cleaning System including chemical pump, cartridge filter, tanks etc.

i pH correction system incl. chemical dosing pump, tanks etc.

Instrumentation including flow meters, digital TDS meter, digital pH meter, pressure gauges, low

pressure switch, high pressure switch etc. complete.

SS-316L (8 kg/cm2) piping and ABS valves for low pressure and SS-316, schedule 10 piping and SS-

316 L valves for high pressure piping in the plant.

Electrical panel including all starters, overload relays, single phase preventers, voltmeters, ammeters,

MCB's, indicating lights, push buttons, rocker switches, incomers, auto-manual switches etc. complete.

m All cabling , connections, terminations etc. required for the job. 1 1 Each 2,31,823.82 2,31,823.82

TOTAL FOR SUB HEAD - XI CARRIED TO SUMMARY OF PRICES 2,31,823.82

SUBHEAD-IX: ROOF TOP SOLAR SYSTEM

8.1 NSR 83 For Solar Water Heating System-500 LPD

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

a) Providing and fixing Solar Hot Water indirect Heating System using heating liquid medium comprising

of flat plate solar panels, including all interconnecting insulated G.I. piping, primary and secondary

recirculation pumps, pressure type insulated hot water tank, , outlet, Y stainer and a water meter on the

inlet, air release valve all mounted on galvanized MS sections complete with connection with the

existing piping. Comparising of following:-

b) Five Nos of. flat plate solar collector panels of 10 Sqm size approx. the panels enclosed in insulated

collector boxes with single piece toughned glass 4 mm thick and fixed with heat resistant gasket.

c) One Lot of Inter-connected insulated G.I. piping insulated with 9 mm thick nitrile rubber heat resitant

insulation sections ( Vidoflex or equiv.) and valves with outer mechanical protection of aluminium sheet

8.1.1 Solar Water Heating System as Describe Above 1 1 Set 88,846.97 88,846.97

TOTAL OF SUB HEAD IX - SOLAR SYSTEM - 88,846.97

SUBHEAD-X: HARVESTING PITS

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated

earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers

10.2 2.25 not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 3 3 Cum 196.00 190.71 572.12

50 m and lift upto 1.5 m.

10.3 2.26 Extra for every additional lift of 1.5 m or part thereof in. - -

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

10,4,1 4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 2 2 Cum 6812.00 6,628.08 9,942.11

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,

balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor

10.5 5.3 five level excluding the cost of centering, shuttering, finishing & reinforcement with1:2:4 (1 cement: 2 2 2 Cum 11505.50 11,194.85 22,389.70

coarse sand: 4 graded stone aggregate 20 mm nominal size)

10.6 5.9 Centring and shuttering including stutting, propping etc. and removal of form for: - -

10,6,1 5.9.3 Suspended floors, roofs, landings, balconies and acees platform 9 9 Sqm 927.25 902.21 8,119.93

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding

10,7,1 5.22.6 Thermo-Mechanically Treated bars. 150 150 Kg. 107.85 104.94 15,740.71

10.8 6.1 Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: - -

10.9 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 18 18 Cum 7132.25 6,939.68 1,24,914.23

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910

on 12mm dia steel bar conforming to IS :1786 having minimum cross section as 23 mm x 25 mm and

over all minimum length 263mm and width as 165mm with minimum 112mm space between

protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and

adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with

stand the bend test and chemical resistance test as per specifications and heaving manufactures

permanent identification mark to be visible even after fixing " including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6: (1 cement :3 coarse sand :6 graded stone aggregate

20mm nominal size )complete as per design.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved

10,11,1 19.19.3.1 HD-20 circular shape 560 mm internal diameter. 2 2 Each 1675.70 1,630.46 3,260.91

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:

2800 (part I), including collecting samples from different strata, preparing and submitting strata

10.12 23.1 chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required - -

for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground

10,12,1 23.1.1 All types of soil - -

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium

well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour

charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium

well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings &

accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in

10.15 23.5 the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 5 5 Cum 1509.80 1,469.04 6,610.66

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over

10.16 23.6 the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of 5 5 Cum 1538.25 1,496.72 6,735.23

Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in

10.17 23.7 required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer –in- 9 9 Cum 1538.25 1,496.72 13,470.46

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/

10.18 23.8 medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of 10 10 Cum 2024.50 1,969.84 19,698.39

Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well

housing/ casing pipe, removable as per requirement, all complete for borewell of:

Digitally signed by

PRADYUMNA MUKHERJEE

QTY Modified Rate AMOUNT

S.NO. DESCRIPTION OF ITEMS UNIT RATE (Multiplying

factor @ 0.973) DSR NSR

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS:

2800 (part I), including necessary bolts & nuts of required size complete.

TOTAL OF SUB HEAD X - HARVESTING PIPT 6,79,068.40 -

SUBHEAD-XI: LANDSCAPE IRRIGATION SYSTEM

Providing, laying, Jointing, Testing and commissioning of UPVC pressure pipes of 10Kg/Sqcm pressure

rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports,

and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of

surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement

concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard

design (For garden hydrants).

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by

11.8 DSR 18.60 Municipal Board complete with bolts, nuts, rebber insertions etc. (The tail pieces if required will be paid

Providing and fixing of cast iron wafer type butterfly valves (PN 10) complete with 2 nos. matching

flanges ( table-E) , bolts, nuts, washers 3 mm thick insertion neoprene gasket conforming to IS 13095.

Supply, installation, testing and commissioning of PGP Gear Driven Sprinkler with popup height of 4" &

11.10 NSR 89 radius 4-5.8 m check valve for drainage prevention seal and all other features including Swing joints and 4.00 4 Each 4,560.47 18,241.87

all assessories as per specification complete .

Supply, installation, testing and commissioning of PGP Shrub Sprinkler with radius 4-5.8 m with ASTM

11.11 NSR 90 pipe riser and all accessories as per specification. 2.00 2 Each 3,379.27 6,758.53

11.12 NSR 91 Providing and fixing brass automatic air vent at the top of each riser. 2.00 2 Each 1,499.61 2,999.23

TOTAL OF SUB HEAD XI - LANDSCAPE IRRIGATION 5,320.70 47,453.52

Digitally signed by

PRADYUMNA MUKHERJEE

BILL OF QUANTITIES FOR ELECTRICAL WORKS FOR ITO SAKET

SUMMERY OF COST

S. No. DESCRIPTION OF ITEM

DSR NON DSR TOTAL (DSR & NON DSR)

Digitally signed by

PRADYUMNA MUKHERJEE

BILL OF QUANTITIES FOR ELECTRICAL WORKS FOR ITO SAKET

(DSR 2022 ITEM)

S.No. DSR - 2022 DESCRIPTION OF ITEM UNIT LOWER UPPER RATE RATE M.F LOWER UPPER

FLRs TOTAL FLRs (DSR)

BMT BMT @1.063 BMT BMT

1.0 Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed

medium class PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single

core cable etc as required.

2.0 Wiring for twin control light point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in

surface / recessed medium class PVC conduit, 2 way

modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm. FRLS PVC insulated

1.11 copper conductor single core cable etc as required. Point 2 2 28 32 1562 1660 3321 3321 46491 53133

3.0 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed medium class PVC conduit alongwith 1 No 4

sq. mm FRLS PVC insulated copper conductor single

1.12 core cable for loop earthing as required. Metre 200 200 2880 3280 334 355 71008 71008 1022521 1164538

4.0 Wiring for circuit/ submain wiring alongwith earth wire

with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed

1.14 medium class PVC conduit as required

CIRCUIT / SUBMAIN WIRING

5.0 Supplying and drawing 2 pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored

telephone cable in the existing surface/ recessed steel/

1.18 PVC conduit as required.

7.0 Supplying and fixing of following sizes of PVC conduit

along with the accessories in surface/recess including

painting in case of surface conduit, or cutting the wall and

making good the same in case of recessed conduit as

1.21 required.

8.0 Supplying and fixing following modular switch/ socket on

the existing modular plate & switch box including

connections but excluding modular plate etc. as required.

9.0 Supplying and fixing suitable size GI box with modular

plate and cover in front on surface or in recess, including

providing and fixing 3 pin 5/6 A modular socket outlet and

5/6 A modular switch, connections etc. as required.

10.0 Supplying and fixing suitable size GI box with modular

plate and cover in front on surface or in recess, including

providing and fixing 6 pin 5/6 A & 15/16 A modular socket

outlet and 15/16 A modular switch, connections etc. as

11.0 Supplying and fixing following size/ modules, GI box

alongwith modular base & cover plate for modular

1.27 switches in recess etc as required.

11.1 1.27.1 1 Module (75mmX75mm) -For Telephone,TV outlet, data Each 2 2 34 38 298 317 634 634 10770 12037

12.0 Supplying and fixing brass batten/ angle holder including

1.34 connection etc. as required. Each 3 3 10 16 131 139 418 418 1393 2228

13.0 Supplying and fixing call bell/ buzzer suitable for single

1.38 phase, 230 volts, complete as required. Each 0 0 180 180 99 105 0 0 18943 18943

14.0 Supplying and fixing modular blanking plate on the

existing modular plate & switch box excluding modular

15.0 Supplying and fixing stepped type electronic fan regulator

on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

16.0 Installation, testing and commissioning of ceiling fan,

including wiring the down rods of standard length (upto

30 cm) with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable, including providing and

fixing phenolic laminated sheet cover on the fan box etc.

17.0 Installation of exhaust fan in the existing opening,

including making good the damage, connection, testing,

commissioning etc. as required.

18.0 Extra for fixing the louvers/ shutters complete with frame

1.51 for a exhaust fan of all sizes. Each 2 2 56 60 207 220 440 440 12322 13202

S.No. DSR - 2022 DESCRIPTION OF ITEM UNIT LOWER UPPER RATE RATE M.F LOWER UPPER

FLRs TOTAL FLRs (DSR)

BMT BMT @1.063 BMT BMT

19.0 Supplying and fixing 20 amps, 240 volts, SPN industrial

type, socket outlet, with 2 pole and earth, metal enclosed

plug top alongwith 20 amps “C” curve, SP, MCB, in sheet

steel enclosure, on surface or in recess, with chained

metal cover for the socket out let and complete with

connections, testing and commissioning

20.0 Supplying and fixing of following sizes of STEEL conduit

alonwith the accessories in surface/recess including

painting in case of surface conduit, or cutting the wall and

making good the same in case of recessed conduit as

1.20 required.

21.0 Wiring with the following sizes of FRLS insulated copper

conductor single core cables in existing surface/recessed

M.S. conduit etc. as complete as required

22.0 Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240 volts, on

surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But

2.3 without MCB/RCCB/Isolator)

23.0 Supplying and fixing following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board,

415 volts, on surface/recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc.

as required. (But without MCB/RCCB/Isolator)

24.0 Supplying and fixing of following rating 240 volts, C series

MCB suitable for inductive loads of following poles in the

existing MCB DB complete with connections, testing and

commissioning etc.,as required.

25.0 Supplying and fixing following rating, double pole, 240

volts, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

26.0 Supplying and fixing following rating, four pole, 415 volts,

isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

27.0 Supplying and fixing of following rating double pole 240

volts, resudual current circuit breaker (RCCB), having a

sensivity current up to 300 miliampere in the existing

MCB DB complete with connections, testing &

2.14 commissioning etc. as required.

28.0 Earthing with copper earth plate 600 mm X 600 mm X 3

mm thick including accessories, and providing masonry

enclosure with cover plate having locking arrangement

and watering pipe of 2.7 metre long etc. with charcoal/

29.0 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry

enclosure with cover plate having locking arrangement

and watering pipe of 2.7 metre long etc. with charcoal/

30.0 Providing, Fixing, Testing & Commissioning of following

copper strip wire on surface of wall/ trench including

insulator with heat shrinkable sleeves etc. as required.

30.1 Providing and fixing earth bus of 50 mm x 5 mm copper

strip on surface for connections etc. as required.

Providing and fixing 25 mm x 5 mm copper strip on

5.14 surface or in recess for connections etc. as required. Metre 0 0 150 150 1162 1235 0 0 185281 185281

31.0 Providing, Fixing, Testing & Commissioning of following

G.I. Strip/ G.I. wire on surface of wall/ trench etc. as

31.2 Providing and fixing 25 mm X 5 mm G.I. strip on surface

5.15 or in recess for connections etc. as required Metre 50 50 50 150 244 259 12969 12969 12969 38906

S.No. DSR - 2022 DESCRIPTION OF ITEM UNIT LOWER UPPER RATE RATE M.F LOWER UPPER

FLRs TOTAL FLRs (DSR)

BMT BMT @1.063 BMT BMT

31.3 Providing and fixing 6 SWG dia G.I. wire on surface or in

recess for loop earthing along with existing surface/

recessed conduit/ submain wiring/ cable as required.

32.0 Providing and fixing of lightning conductor finial, made of

25 mm dia 300 mm long, G.I. tube, having single prong

at top, with 85 mm dia 6 mm thick G.I. base plate

6.2 including holes etc. complete as required. Each 0 0 2 2 518 551 0 0 1101 1101

33.0 Jointing copper / G.I. tape (with another copper/ G I tape,

base of the finial or any other metallic object) by riveting /

nut bolting/sweating and soldering etc as required.

34.0 Providing and fixing G.I. tape 20 mm X 3 mm thick on

parapet or surface of wall for lightning conductor

6.7 complete as required. (For horizontal run) Metre 200 200 200 600 126 134 26788 26788 26788 80363

35.0 Providing and fixing G.I. tape 20 mm X 3 mm thick on

parapet or surface of wall for lightning conductor

6.8 complete as required. (For Vertical run) Metre 200 0 200 400 197 209 41882 0 41882 83764

36.0 Providing and fixing testing joint, made of 20 mm X 3 mm

thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts,

nuts, chuck nuts and spring washers etc. complete as

37.0 Providing and laying G.I. tape 32 mm X 6 mm from earth

6.14 electrode directly in ground as required. Metre 180 180 60 420 195 207 37311 37311 12437 87060

38.0 Providing and fixing testing joint, made of 20 mm X 3 mm

thick copper strip, 125 mm long, with 4 nos. of tinned

brass bolts, nuts, chuck nuts and spring washers etc.

6.11 complete as required. Each 4 4 4 12 0 0 0 0 0 0

39.0 Supply and making end termination with brass single

compression glands and aluminium lugs following sizes

of XLPE insulated and PVC sheathed/ XLPE aluminium

conductor cable of 1.1 KV grade of the following sizes as

40.0 Supplying and installing following size of perforated pre-

painted M.S. cable trays with perforation not more than

17.5%, in convenient sections, joined with connectors,

suspended from the ceiling with M.S. suspenders

including bolts & nuts, painting suspenders etc as

41.0 Supplying and installing following size of perforated pre-

painted M.S. cable trays bends with perforation not more

than 17.5%, joined with connectors, suspended from the

ceiling with M.S. suspenders including bolts & nuts,

4.2 painting suspenders etc as required.

42.0 Supplying and installing following size of perforated pre-

painted M.S. cable trays reducers with perforation not

more than 17.5%, joined with connectors, suspended

from the ceiling with M.S. suspenders including bolts &

4.3 nuts, painting suspenders etc as required.

43.0 Supplying and installing following size of perforated pre-

painted M.S. cable trays Tee’s with perforation not more

than 17.5%, joined with connectors, suspended from the

ceiling with M.S. suspenders including bolts & nuts,

4.4 painting suspenders etc as required.

44.0 MV CABLE LAYING-

S.No. DSR - 2022 DESCRIPTION OF ITEM UNIT LOWER UPPER RATE RATE M.F LOWER UPPER

FLRs TOTAL FLRs (DSR)

BMT BMT @1.063 BMT BMT

44.1 Laying of one number PVC insulated and PVC sheathed

/ XLPE power cable of 1.1 KV grade of following size

direct in ground including excavation, sand cushioning,

protective covering and refilling the trench etc as

44.2 Laying of one number additional PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

following size direct in ground in the same trench in one

tier horizontal formation including excavation, sand

cushioning, protective covering and refilling the trench

7.2 etc as required.

44.3 Laying and fixing of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

7.8 following size on cable tray as required.

a 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 150 240 0 390 45 48 7175 11480 0 18656

b Above 35 sq. mm and upto 95 sq. mm (clamped with

c Above 95 sq. mm and upto 185 sq. mm (clamped with

d Above 185 sq. mm and upto 400 sq. mm (clamped with

45.0 INSPECTION CHAMBER:

Constructing brick masonry chamber for underground

C.I. inspection chamber and bends with bricks in cement

mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with

frame (light duty) 455x610 mm internal dimensions, total

weight of cover with frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15 kg), R.C.C.

top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size), foundation

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded

stone aggregate 40 mm nominal size), inside plastering

12 mm thick with cement mortar 1:3 (1 cement : 3

coarse sand), finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete as per

19.3 standard design :

45.1 Inside dimensions 600x 850 mm and 45 cm deep for

19.30.3 pipe line with three or more inlets.

45.1.1 With common burnt clay F.P.S. (non modular) bricks of

45.1.1. Extra for depth beyond 45 cm of brick masonry chamber

45.2.1 With common burnt clay F.P.S. (non modular) bricks of

46.0 Providing, laying & fixing following dia RCC pipe NP2

class (light duty) in ground complete with RCC collers,

jointing with cement mortor 1:2 (1 cement : 2 fine sand)

including trenching (75 cm deep) and refilling etc. as

14.14 required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable

47.0 in the existing surface/ recessed steel/ PVC conduit as

48.0 Providing and fixing MV danger notice plate of 200

mm x 150 mm made of mild steel at least 2mm thick &

vitreous enamelled white on both sides and with

inscription in signal red colour on front side as

49.0 Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed steel

conduit conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable

1.3 etc as required.

50.0 Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5

sq. mm FRLS PVC insulated copper conductor single

1.54 core cable etc. as required.

54.0 RISING MAIN-

S.No. DSR - 2022 DESCRIPTION OF ITEM UNIT LOWER UPPER RATE RATE M.F LOWER UPPER

FLRs TOTAL FLRs (DSR)

BMT BMT @1.063 BMT BMT

Supplying, installing on wall, testing and commissioning

of following capacity Air Insulated Compact Type Rising

Mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply

with enclosure having IP-54 rating after fixing the tap off

boxes and all accessories, made of 1.6mm thick steel

sheet duly powder coated in convenient sections

complete with 4 Nos. aluminium bus bars having current

density of 130 A/ sq cm at nominal current rating,

necessary joints & expansion joints, fire barrier at each

floor, provision of tapping at every meter, continuous

earthing with 2 Nos. aluminium strip of suitable size (one

on each side) including, G.I. clamping brackets, angle

iron bracket, steel fasteners, connecting to earthing

system etc. as required.

55.0 11 KV END TERMINATION:

55.1 Supply & making of INDOOR cable end termination with

heat shrinkable jointing kit complete with all accessories

including lugs suitable for following size of 3 core XLPE

aluminium conductor cable of 11 KV grade as required.

55.2 Supply & making of OUTDOOR cable end termination

with heat shrinkable jointing kit complete with all

accessories including lugs suitable for following size of 3

core XLPE aluminium conductor cable of 11 KV grade as

10.5 required.

56.0 HT CABLE LAYING:

56.1 Laying of one number XLPE power cable of 11 KV grade

of following size in the existing masonry open duct as

57 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable

in the existing surface/ recessed steel/ PVC conduit as

TOTAL OF DSR ITEM CARRIED OVER TO SUMMARY 4044467 2254609 9988500 15966975

BILL OF QUANTITIES FOR ELECTRICAL WORKS FOR ITO SAKET

(NON DSR ITEMS )

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

S.H.-I DISTRIBUTION PANELS 840133 4398686 1546112 6784931

S.H.-II MAIN & SUB MAIN CABLES 1230156 697448 902860 2830463

S.H.-III SUPPLY & FIXING OF LIGHT FIXTURES & FANS 1922643 1922643 5632499 9477785

S.H.-VII SUBSTATION WORK 0 0 20258008 20258008

S.H.-X SOLAR SYSTEM 0 0 5796689 5578768

S.H.-I DISTRIBUTION PANEL & DISTRIBUTION BOARDS-

1.1 LIFT PANEL -

1 No. 100 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 150 Amp digital Ammeter with selector switch and

1 Set of phase indicating lamps with HRC fuses.

1 Set of ON/OFF indicating lamps with HRC fuses.

200 Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

04 Nos. 63 Amp TP+N Moulded Case Circuit Breaker.

02 Nos. 40 Amp DP Miniature Circuit Breaker.

06 Nos. 40 Amp TPN Miniature Circuit Breaker.

01 Nos. 63 Amp TPN Miniature Circuit Breaker.

Panel described as above Set 1 1 0 2 184701 184701 184701 0 369401.62

1 No. 63 Amp TPN Miniature Circuit Breaker.

100Amp TPN copper busbar.

01 No. 63 Amp FP RCBO.

02 Nos. 40 Amp DP Miniature Circuit Breaker.

Panel described as above Set 0 0 6 6 30647 0 0 183881 183881.4

1.3 TYP FLOOR PANEL-

1 No. 160 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

200Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

02 Nos. 100 Amp TP+N Moulded Case Circuit Breaker.

02 Nos. 40 Amp DP Miniature Circuit Breaker.

03 Nos. 25 Amp DP Miniature Circuit Breaker.

1.14 UPPER BASEMENT L+P PANEL

1 No. 100 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

150Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

01 Nos. 63 Amp TP+N Moulded Case Circuit Breaker.

05 Nos. 63 Amp TPN Miniature Circuit Breaker.

30 Nos. 40 Amp TPN Miniature Circuit Breaker.

Panel described as above Set 0 1 0 1 232417 0 232417 0 232416.71

1.15 LOWER BASEMENT L+P PANEL - 1, 2 & 3

1 No. 100 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

150Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

05 Nos. 63 Amp TPN Miniature Circuit Breaker.

30 Nos. 40 Amp TPN Miniature Circuit Breaker.

Panel described as above Set 0 1 0 1 218784 0 218784 0 218783.6

1.16 VENTILATION PANEL -

1 No. 200 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 200 Amp digital Ammeter with selector switch and

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

315 Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

20 Nos. 40 Amp TP+N Moulded Case Circuit Breaker.

Panel described as above Set 1 0 0 1 225600 225600 0 0 225600.15

1.17 INVERTER PANEL BASEMENT - 1, 2 & 3

1 No. 63 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

150Amp TPN aluminium busbar with coloured heat

shrinkable sleeve.

02 Nos. 63 Amp DP Miniature Circuit Breaker.

Panel described as above Set 0 0 1 1 75636 0 0 75636 75635.89

1.18 MCCB BOX WITH MCCB (INCOMMING/OUTGOING)

INCOMING/OUTGOING

1 No. 63 Amp FP Moulded Case Circuit Breaker.

Panel described as above Set 0 1 0 1 13606 0 13606 0 13605.51

2.0 END FEED UNIT-

Design, Manufacturing, Supply, Receiving, Unloading,

Shifting, Installation, Testing & Commissioning of following

End Feed Unit housing fabricated out of 14G CRCA powder

coated (as approved) sheet steel for the Rising Mains fitted

with following MCCB. The End Feed Unit should complete

with solid aluminium links of rated capacity of MCCB to

Rising Mains. The End Feed Unit should be complete with

suitable size of glands plate for incoming cables. All MCCB

shall have Ics value of 50 KA. Each end feed unit shall have

a set of 3 nos. phase LED Type indicating lights with control

3.0 TAP OFF UNIT-

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

Design, Manufacturing, Supply, Receiving, Unloading,

Shifting, Installation, Testing & Commissioning of cubical

type tap off unit box fabricated out of 2.0 mm thick CRCA

sheet, dust and vermin proof, with hinged detachable doors

and painted front, comprising LED type indication lamps

with toggle switches and 4 pole MCCB terminated directly

with tap off box with Bus Bar links on the incoming side and

suitable for cable connection on the outgoing side including

making connections, interconnections, earthing complete as

required. All MCCB shall have Ics value of 36 KA and

Thermal Magnetc release for over current & short circuit.

4.0 DG Synchronizing Cum Changeover Panel (1x625 KVA

D.G. Set + 1x250 )-

Supply, Erection, Testing & Commissioning of Main DG

Control panel with D.G. Synchronizing controller & Micro

PLC, this will be floor mounted, free standing,

compartmentalized, indoor duty, dust proof, vermin proof,

front operated, electrical panel fabricated, painted and

manufactured exactly as per specifications laid in this

document and will be complete with the main and

auxiliary bus bars, interconnection, earth terminals, earth

bus and will be powdered coated finished. All the busbar

joint shall be protected by clip on type sleeve. The DG

control panel shall use all draw out 3 position withdrawn

type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire

supply system and will have fault level of 50 KA or as

required as per consultant approval. The panel will be

made as per detailed specifications and drawings forming

part of this document. (Under no case temperature of LT

Panel shall be more at any point of the panel, otherwise

necessary exhaust fan shall be have to provided) Bus bar

calculations considering temperature derating, enclosure

derating, sleeving derating must be done and submitted

for checking. (The D.G. Set controller shall be part of D.G.

The DG vendor shall make complete protection curves and

discrimination chart for relay settings and shall adjust all

these readings at site. The bus bar size shall not be less

than the ampere sizes mentions after derating. The bidder

will show exact calculations & compare the figure of 0.66

and final calculations will be adopted for more stringent

condition. each incommer shall have surge protection

device. The PCC panel will comprise of the following :

Each incoming / outgoing breaker shall have

microprocessor release with adjustable over current, short

circuit & earth fault protection with instantaneous as

mentioned in specification. The Panel will be made as per

detailed specifications & drawings forming part of this

document. Fault level of panel shall be 25 KA.

All the MCCB up to 250 Amp shall have thermal release

with adustable overload, short circuit & earth fault protection

and above shall have microprocessor release with

adjustable overload, short circuit & earthfault protection.

The panel shall be manufactured as per BOQ, tech

specification and drawing.

One set of Generator control relay for Each D.G. Set with

accessories for AMF, Load Management, Synchronizing

and Interlocking through micro PLC.

1 Nos. 1250A and 1 nos 400A feeder incomer and Each

incomer breaker feeder shall have following: (For 625

KVA D.G. Set and 400A D.G set )-

One number incomer 3P 1250 amps EDO breaker with

1600 Amp TP neutral contactor. Each breaker shall have

microprocessor based releases for O/C,S/C & earth fault

protection with instantaneous.

3 No. indicating lamps to show the incoming power along

with HRC fuses.

1 No. digital ammeter, ammeter selector switch, digital

voltmeter, Voltmeter selector switch.

1 No. Load Manager EM 6400 with RS 485 port

1 no. REF relay

Announciation window to cover LLOP, HWT, OIL Pressure,

U/V, O/V, U/F, O/F, O/C, E/F, REF relay faults shall be

provided. 2 nos phase reversal relay shall be provided.

Engine should trip on LLOP, HWT, oil temp, O/V, O/F and

breaker should trip on other faults.

Initially U/V & U/F will be bye passed till oil pressure is

Indicating lights for ACB ON / OFF, ACB trip, neutral

contactor ON, D.G. on mains, D.G. fails to start.

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

Generator start /stop facility through push button from panel,

necessary cranking relay shall be provided.

Suitable battery charger for 24V 360 AH with d.c voltmeter

& d.c ammeter. D.C voltmeter and ammeter will be

Whenever D.G. stop through PB, load shall be

disconnected first.

Incomming Feeder from Main L.T. Panel (Grid Supply):

Transformer 2 Nos 400KVA

2 No. 800 Amp FP Electrically operated horizontal drawout

type Air Circuit Breaker microprocessor based releases for

O/C,S/C & earth fault protection with instantaneous. (For

Incommer) (25 KA)

1 Nos. 1250Amp FP Electrically operated horizontal

drawout type Air Circuit Breaker as buscoupler with

interlocking arrangement with incomers. (25 KA)

1 Sets of indicating lamps for ON & OFF of bus coupler.

1600 Amp TPN busbars of aluminium alloy as per SLD.

02 No. 1250 Amp FP MDO Air Circuit Breaker.

01 No. 400 Amp FP Moulded Case Circuit Breaker.

02 Nos 250A FP Moulded Case Circuit Breaker.

02 Nos 100A TP+N Moulded Case Circuit Breaker.

05 Nos 63A TP+N Moulded Case Circuit Breaker.

2 Nos. 0 to 500 Volt digital voltmeter with Voltmeter

Selector Switch & Protective SP MCB (96mm square) (one

for each Incoming Breaker).

2 No. 0 to 1250 Amp digital ammeter (96mm square) with

2 Sets of phase indicating lights (RYB) with protection fuses

(one set for each incoming breaker).

2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for

each incoming breaker).

2 Sets trip circuit healthy indicating lamp (one set for each

incoming breaker).

2 Sets auto trip indicating lamp (one set for each incoming

2 Nos. Multifunction Meter (one for each Incoming Breaker).

BATTERY & BATTERY CHARGER

1 No. 24V, 72AH SMF Battery with suitable battery charger

for control supply.

D.G. Synchronizing Cum Changeover Panel describe as

135 KVAR CAPACITOR BANK PANEL - 02 SET. (EACH

SET SHALL HAVE FOLLOWING)-

1 Nos. 1000 Amp FP MDO Air Circuit Breaker. (Already

Considered in Main. L.T. Panel Outgoing)-

1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter

Selector Switch & Protective SP MCB (96mm square).

1 No. 0 to 1000 Amp digital ammeter (96mm square) with

1 Sets of phase indicating lights (RYB) with protection

1 Sets breaker 'ON' & 'OFF' indicating lamp.

12 Step Automatic Power Factor Correction relay (APFC

1250 Amp TPN busbars of aluminium alloy as per SLD.

2 Nos. 125 Amp TP MCCB.

1 Nos. 63 Amp TP MCCB.

1 Nos. 32 Amp TP MCCB.

2 Nos. capacitor duty contactor (one for each 50 KVAR

capacitor unit).

2 Nos. capacitor duty contactor (one for each 25 KVAR

capacitor unit).

2 Nos. capacitor duty contactor (one for each 10/5 KVAR

capacitor unit).

4 Nos. 50 KVAR Capacitor Bank.

2 Nos. 25 KVAR Capacitor Bank.

1 Nos. 10 KVAR Capacitor Bank.

2 Nos. 05 KVAR Capacitor Bank.

9 sets of push button stations Red and Green for manual

operation of capacitor units with auto/manual selector

1 No. Indicating lamp for each 50 / 25 / 10 / 5 KVAR

capacitor unit to indicate that the unit is 'ON'.

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

1 No. Toggle switch for changing automatic to manual

operation of capacitor units.

Power factor meter.

Panel described as above Set 1 0 0 1 217921 217921 0 0 217920.63

6.0 EXTERNAL LIGHTING PANEL (OUTDOOR TYPE)-

Design, Manufacturing, Supply, Receiving, Unloading,

Shifting, installation, testing & commissioning of cubicle type

totally enclosed free standing type moisture, dust and

vermin proof Floor Distribution Panel made out of 2.0 mm

thick & front cover 1.6 mm thick CRCA sheet complete with

following equipments, including digital ammeter with inbuilt

ammeter selector switch, digital voltmeter with inbuilt

voltmeter selector switch, indicating lamps, CT's, internal

wiring with suitable size wires / cable, interconnection,

painting complete as per specification & drawing.

1 No. 63 Amp FP ( 35 KA Ics) Moulded Case Circuit

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector

1 No. 60 Amp digital ammeter with inbuilt selector switch

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set 24 Hrs TSQ Timer

1 Set 63 Amp, 4P Contactor & A/M switch and Push Button.

100 Amp TPN aluminium busbar.

08 No. 25 Amp DP MCB.

03 No. 40 Amp TPN MCB.

Panel described as above Set 0 0 1 1 163815 0 0 163815 163815.3

7.0 Supplying, installing by suspension on ceiling/along the wall,

testing and commissioning of following capacity Sandwich

Type Bus Duct (Outdoor Type) for use on 3 phase 4 wire

415 V, 50Hz A.C. supply with metal clad enclosure having

IP-54 rating after fixing the tap off boxes and all

accessories, made of 1.6mm thick steel sheet duly powder

coated in convenient sections complete with 4 Nos.

aluminium bus bars having current density of 130 A/sq. cm

at nominal current rating, necessary joints, elbow joints &

expansion joints and bends, fire barrier at each floor,

provision of tapping at every meter, adopter box and copper

flexible for joints, continuous earthing with 2 Nos. aluminium

strip of suitable size (one on each side) including, G.I.

clamping brackets, suspenders, angle iron bracket, steel

fasteners, connecting to earthing system etc. as required

8.0 Supply, fixing, testing and commissioning of automatic

Linear pneumatic Tube Detection based Novec 1230

System for Electrical Panels (Linear Pnuematic Heat

Detection Tube Panel Protection System), consisting of the

following Mentioned components-

8.1 10 LB capacity Novec 1230 , DLP Assembly with automatic

valve, push in connector for tube, 10 LB Novec 1230 gas ,

mounting bracket, End of Line adopter and low pressure

switch for monitoring system activation. No 0 0 0 1 340168 0 0 0 340168.29

8.2 Linear Pneumatic Heat detection tube with all necessary &

8.3 Master Control Unit with Audio Visual Alarm with wiring to

make complete system operational . The control Panel

should have provision for integration with fire Alarm

/SCAD/BMS System.

TOTAL OF DISTRIBUTION PANEL CARRIED OVER TO

S.H.-II MAIN & SUB MAIN CABLES

1.0 Supply of following sizes of 1.1KV grade multicore

aluminium conductor XLPE insulated and PVC sheathed

armoured cable conforming to relevant IS (Cable shall be

purchased only after approval of cable schedule by architect

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

2.0 Supply & Laying of following sizes of 1.1KV grade

multistranded copper conductor PVC insulated cable

including termination complete as required in existing cable

2.1 1Cx16 sq.mm PVC Insulated cu wire including termination

etc. for UPS neutral earthing and UPS. Meter 0 0 500 500 94 0 0 47215 47215

2.2 1Cx35 sq.mm PVC Insulated cu wire including termination

etc. for D.G. neutral earthing Meter 0 0 200 200 205 0 0 40970 40970

TOTAL OF MAIN & SUB MAIN CABLES CARRIED

OVER TO SUMMERY

S.H-III SUPPLY & FIXING OF LIGHT FIXTURES & FANS

INTERNAL LIGHTING-

1.0 Supply, Installation, Testing & Commissioning of 1x22 Watt

LED Light Fixture surface mounted as per technical

specification as per tender make.

2.0 Supply, Installation, Testing & Commissioning of 10 W

Surface Mounted LED down light as per tender make. Each 150 150 1000 1300 2192.28 328842 328842 2192280 2849964

3.0 Supply, Installation, Testing & Commissioning of 15 W

Recess Mounted LED down light as per tender make. Each 150 150 500 600 2978.25 446738 446738 1489125 2382600

4.0 Supply, Installation, Testing & Commissioning of 1x10 Watt

LED Light Fixture surface mounted as per technical

specification as per tender make. Each 0 0 76 76 749.65 0 0 56973 56973

5.0 Supply, Installation, Testing & Commissioning of Light

Fixture surface mounted.

6.0 Supply, Installation, Testing & Commissioning of GARRNET

12W LED BULB suitable for batten holder. Each 0 0 60 60 1407.77 0 0 84466 84466

7.0 Supply, Installation, Testing & Commissioning of Bracket

Light Fixture surface mounted.

8.0 Supply of following sizes of heavy duty exhaust fan for

single phase 230 volt, 50HZ AC supply complete with

motor, blades, frame, bracket, louver/ shutter etc as

required. 0 0 0 0

9.0 Supply of following sizes of ceiling fan complete with

double ball bearing, motor, blades, downrod, canopy,

capacitor etc. suitable for operation on 230 volt, 50 Hz, A.C.

supply complete as required.

17.0 Supply, Installation, Testing & Commissioning of Integral

LED aviation light comprising of aluminium housing with

polycarbonate enclosure with flasher suitable for 230V AC

complete with fitting including photochromatic switch for

automatic ON/OFF of Aviation lights complete as per

approved equivalent.

TOTAL OF LIGHT FIXTURES & FANS CARRIED OVER

V FIRE ALARM SYSTEM-

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

1.0 Supply, Installation, Testing & Commisioning of

Microprocessor based X loop fire alarm control panel

expandable upto 10 loops fully networkable with each loop

capable of taking 125 devices, 8 line x 40 character alpha-

numeric liquid crystal display. The panel shall be soft

addressable type. The panel shall be able to give pin point

location of all fire/fault conditions. Further, the panel must

be able to automatically switch off respective control

switches when ever any alarm is triggered. The panel shall

have in built rectifier, Loop cards,provision for externel &

internal printer (if required), LCD unit to indicate Fire/Fault

Signal with address and analog output, built in printer to log

all fire or fault events complete in all respects, integral SMF

lead acid batteries with sealed cells of 24 V capable of

running for a minimum of 8 hours with integral battery

charger complete as required and as per specification. The

fire alarm panel shall be suitable for software integration

with BMS & PA system.

2.0 Supply, Installation,Testing & Commisioning of Analog

Addressable Intelligent multisensor detector with two inbuilt

optical smoke sensors with light angles as well as additional

heat detector sensor with decentralise intelligence, soft

addressable Photothermal type with inbuilt fault isolator as

per NFPA style 7 wiring complete with base as required.

3.0 Supply Installation, Testing & Commissioning of Intelligent

addressable Manual Call Point / Pull station complete as

4.0 Supply, installation, testing and commissioning of

addressable control module complete as per specification.

5.0 Supply, installation, testing and commissioning of

addressable monitor module complete as per specification.

6.0 Supply Installation, Testing & Commissioning of wall

mounting loop powered addressable type hooter with all

7.0 Supply Installation, Testing & Commissioning of Response

8.0 SITC of EN54-16 compliant IP Based Digital Public Address

& Voice Alarm system. The selected system devices like

controllers and Paging Microphones, should use the TCP/IP

technologies and build on the standard network platform to

ensure expandability. The individual systems should be able

to play 4 simutaneous audio messages and also be able to

be networked over IP such that the PA systems in all 10

towers work seamlessly.

SITC of 8 zone IP based, digital Voice Alarm controller

expandable upto 128 zones. The voice alarm controller

should be able to connect directly over Ethernet. It should

have functions like the audio playing, zone control, fault

monitoring, log recording, volume control and amplifier

switchover. The Voice alarm controller should also have the

following functions:

. 255 Priorities

. Time schedule broadcasts

. Its own PTT microphone

. Capable of amplifier redundancy

. 8 trigger inputs/outputs

9.0 SITC of 1x125W Class-D Amplifier with 4 independent

channels and can provide automatic re-settable

overcurrent, overload, overheating, overvoltage, under-

voltage and DC protection .

10.0 SITC of IP based Networkable touch screen paging station

for selection of zones, supervision of system status, setting

of scheduled broadcasts with the following functions:

. Built-in monitoring loudspeaker

. Detachable goose-neck microphone

. LCD touchscreen display

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

11.0 SITC of 2x250W Class-D Amplifier with 4 independent

channels and can provide automatic re-settable

overcurrent, overload, overheating, overvoltage, under-

voltage and DC protection.

12.0 SITC of Network Resource Interface, 4 channels network

audio source, 32 dry contacts in and 8 try contacts out for

13.0 SITC of 6W ceiling mount with back box max SPL1M/1W

96dB . Frequency response of 160Hz-20KHz. The speaker

14.0 SITC of 6W Wall mount with max SPL1M/1W 96dB .

Frequency response of 160Hz-20KHz. The speaker shoud

have tappings at 6W/3W.

15.0 SITC of 10W Wall mount with tappings at 6W/3W. Nos. 10 10 130 150 1908.98 19090 19090 248167 286347

16.0 Wiring for PA system with the following sizes of FRLS

insulated copper conductor single core cables in existing

surface/recessed M.S. conduit etc. as complete as

required. 0 0 0 0

17.0 Supply, Installation, Testing & Commisioning of Analogue

Addressable Intelligent Heat Detector with fixed & rate of

rise temperature function with decentralise intelligence , soft

addressable type, with inbuilt fault isolator as per NFPA

style 7 wiring complete with base as required. Nos. 0 0 32 32 4452.84 0 0 142491 142490.88

18.0 Supply, Installation,Testing & Commisioning of Networkable

Repeater Panel (LCD indicator panel) with 2 line X 20

characters alpha numeric LCD display with all commands

such as reset, mute, silence with suitable battery backup

TOTAL OF FIRE ALARM SYSTEM CARRIED OVER TO

S.H.-VII SUBSTATION WORK

1.1 11KV H.T. METERING PANEL (INDOOR TYPE):

Supply, Receiving, Unloading, Storing, Shifting, Installation,

Testing & Commissioning of indoor type floor mounted,

dust, damp and vermin proof, cubicle HT. Metering Panel

made out of 14 gauge CRCA sheet steel complete with

5Amp electronic trivector meter, C.T.'s of 200/5Amp, 0.5

Class, 10VA Burden, and P.T's of 11KV/ /3, 110V/ /3,

100 VA conforming to relevant IS Standards and complete

as required. H.T. Metering cubicle along with C.T.'s, P.T.'s

and trivector meter shall be got tested and approved from

local electricity supply authority. The GA drawing shall be

got approved by ELECTRICITY BOARD authorities before

1.2 11KV, SINGLE BREAKER PANEL- (INDOOR TYPE)

Supply, Receiving, Unloading, Shifting, Installation Testing

& Commissioning of 11 KV VCB Single Breaker Panel

Board as Icomming / Outgoing shall be metal clad floor

mounting complete as per specification and as described.

630 A VCB Breaker of (350 MVA) 18.4 KA ruputuring

capacity at 11 KV rated, totally enclosed, air insulated metal

clad housing, floor mounting, horizontal isolation, vermin

proof, fully interlocked horizontal drawout type having

isolation features and control devices complete with the

Manually and motor operated, spring charged (release

closing mechanism) trip free type, triple pole truck mounted

draw out, VCB, incorporating mechanical as well as

electrical ON/OFF indication. Spring charge/discharge

mechanical indication"OFF" push buttons for emergency trip

(shrouded) test/service position limit switches with 6

NO/6NC breaker auxilliary contacts in service position, 24

Volts DC shunt trip coil and strip heater to prevent moisture

INCOMMING PANEL - 1 NO. (Incomming Panel shall

have following)-

1 No 630 A VCB Breaker of (350 MVA) 18.4 KA ruputuring

capacity at 11 KV rated, totally enclosed, air insulated metal

clad housing, floor mounting, horizontal isolation, vermin

proof, fully interlocked horizontal drawout type having

isolation features and control devices complete with the

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

3 No. Single Phase double core current transformer 200/5-5

Amp epoxy cast resin insulated class of insulation E.

Core 1-15VA burden class 1.0 for metering.

Core 2-15VA burden class 5P10 for protection.

P.T's of 11KV/1.732, 110V/1.732, 100VA with suitable

rating H.T. & L.T. fuse conforming to relevant IS Standards

and complete as required.

One no. numerical microprocessor based three phase over

current (IDMT element) with earth fault relay with

instantaneous elements.

1 No. Anti Pumping device.

1 No. Circuit breaker control switch for electrical (T/N/C).

1 No. limit switch for test & service position.

1 No. Voltmeter (0-12KV) with selector switch. (96mm

1 No. Ammeter (0-200Amp) with selector switch. (96mm

1 No. electronic type digital energy analyser having 30 days

memory and parameters of KW, KWH, Power factor,

frequency etc. Suitable for BMS compatible with all

1 Set Power Pack Unit.

1 Set of following indicating lamps.

Red, Yellow & Blue for phase indication.

Amber for Trip indication.

Red `ON' Green `OFF'

Spring charge indication.

Auto trip indication.

1 No. hooter with hooter acceptance and reset push button.

1 No. master trip relay. (Electromechanical Type)

1 No. Over voltage relay. (Static Type)

1 No. Under voltage relay. (Static Type)

12 window announciator for all electrical and transformer

1 No.Trip ckt supervision relay (Electromechanical Type)

1 Set of fuses, ferrules, wiring etc. as required.

1 Set of battery and battery charger suitable for 12 Hour

backup for all control supply.

1 No. control Transformer of 1KVA for giving supply to

indication lamps etc having 11 KV/415-230V AC rating

epoxy cast resin dry type Transformer. The connection for

control transformer shall be taken from the cable side

before the circuit breaker tapping.

Note: All spare contacts of breaker or any other equipment

inside the breaker shall be wired upto the outgoing terminal

strip with appropriate ferrules / coding. The terminal strip

rating shall be suitable for connecting two wires of 2.5sqmm

subjected to providing minimum size strip suitable for

H.T. Panel describe as above Set 0 0 1 1 631533.99 0 0 631534 631533.99

11 KV HT VCB Three Breaker Panel Board (Indoor

Type) (1 Incomming + 2 Outgoing)

Supply, Receiving, Unloading, Shifting, Installation Testing

& Commissioning of 11 KV Three Breaker Vacuum Circuit

Breaker Panel Board as 1 Incomming & 2 Outgoing shall be

metal clad floor mounting complete as per specification and

630 A Vacuum circuit breaker of (350 MVA) 18.4 KA

ruputuring capacity at 11 KV rated, totally enclosed,air

insulated metal clad housing, floor mounting, horizontal

isolation, vermin proof, fully interlocked horizontal drawout

type having isolation features and control devices complete

with the following.

Manually and motor operated, spring charged (release

closing mechanism) trip free type,triple pole truck mounted

draw out, vacuum circuit breaker, incorporating mechanical

as well as electrical ON/OFF indication. Spring

charge/discharge mechanical indication"OFF" push buttons

for emergency trip (shrouded) test/service position limit

switches with 6 NO/6 NC breaker auxilliary contacts in

service position, 24 Volts DC shunt trip coil and strip heater

to prevent moisture absorption.

INCOMING PANEL - 1 NO.

1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA

ruputuring capacity at 11 KV rated, totally enclosed,air

insulated metal clad housing, floor mounting, horizontal

isolation,vermin proof,fully interlocked horizontal drawout

type having isolation features and control devices complete

with the following:

3 No. Single Phase double core current transformer 200/5

Amp epoxy cast insulated class of insulation E.

Core 1-15VA burden class 1.0 for metering.

Core 2-15VA burden class 5P10 for protection.

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

P.T's of 11KV/1.732, 110V/1.732, 100VA with suitable

rating H.T. & L.T. fuse conforming to relevant IS Standards

and complete as required.

One no. numerical microprocessor based three phase over

current (IDMT element) (2 O/C+1E/F) with earth fault relay

with instantaneous elements.

1 No. Anti Pumping device.

1 No. Circuit breaker control switch for electrical (T/N/C).

1 No. limit switch for test & service position.

1 No. Voltmeter (0-12KV) with selector switch. (96mm

1 No. Ammeter (0-80Amp) with selector switch. (96mm

1 No. electronic type digital energy analyser having 30 days

memory and parameters of KW, KWH, Power factor,

frequency etc. Suitable for BMS compatible with all

1 Set of following indicating lamps.

Red, Yellow & Blue for phase indication.

Amber for Trip indication.

Red `ON' Green `OFF'

Spring charge indication.

Auto trip indication.

1 No. hooter with hooter acceptance and reset push button.

1 No. master trip relay. ( Electromechanical Type )

1 No.Trip ckt supervision relay. (Electromechanical Type )

600A color coded heat shrinkable sleeved TP Copper

busbar of 350 MVA fault rating.

1 Set of fuses, ferrules, wiring etc. as required.

1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete

1 No. control Transformer of 1KVA for giving supply to

indication lamps etc having 11 KV/415-230V AC rating

epoxy cast resin dry type Transformer. The connection for

control transformer shall be taken from the cable side

before the circuit breaker tapping.

Note: All spare contacts of breaker or any other equipment

inside the breaker shall be wired upto the outgoing terminal

strip with appropriate ferrules / coding. The terminal strip

rating shall be suitable for connecting two wires of 2.5sqmm

subjected to providing minimum size strip suitable for

OUTGOING PANEL - 2 NO. (Each outgoing feeder shall

have following)

1 No 630 A Vacuum circuit breaker of (350 MVA) 18.4 KA

ruputuring capacity at 11 KV rated, totally enclosed,air

insulated metal clad housing, floor mounting, horizontal

isolation,vermin proof,fully interlocked horizontal drawout

type having isolation features and control devices complete

with the following:

3 No. Single Phase double core current transformer 100/5

Amp epoxy cast insulated class of insulation E.

Core 1-15VA burden class 1.0 for metering.

Core 2-15VA burden class 5P10 for protection.

One no. numerical microprocessor based three phase over

current (IDMT element) (2 O/C+1E/F) with earth fault relay

with instantaneous elements.

1 No. Anti Pumping device.

1 No. Circuit breaker control switch for electrical (T/N/C).

1 No. limit switch for test & service position.

1 No. Voltmeter (0-12KV) with selector switch. (96mm

1 No. Ammeter (0-100Amp) with selector switch. (96mm

1 No. electronic type digital energy analyser having 30 days

memory and parameters of KW, KWH, Power factor,

frequency etc. Suitable for BMS compatible with all

1 Set of following indicating lamps.

Red, Yellow & Blue for phase indication.

Amber for Trip indication.

Red `ON' Green `OFF'

Spring charge indication.

Auto trip indication.

1 No. hooter with hooter acceptance and reset push button.

1 No. master trip relay. ( Electromechanical Type)

1 No.Trip ckt supervision relay (Electromechanical Type)

1 Set of fuses, ferrules, wiring etc. as required.

3 No. VAA33 auxiliary relay for transformer fault, alarm and

12 Annunciator window for all electrical and transformer

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

Note: All spare contacts of breaker or any other equipment

inside the breaker shall be wired upto the outgoing terminal

strip with appropriate ferrules / coding. The terminal strip

rating shall be suitable for connecting two wires of 2.5sqmm

subjected to providing minimum size strip suitable for

H.T. Panel describe as above Set 0 0 1 1 1894602 0 0 1894602 1894601.957

1.4 TRANSFORMER 800 KVA (11 KV / 0.415 KV): 0 0 0 0

Design, manufacture, supply, installation, testing and

commissioning of 11 KV /0.415 KV, 3 phase, 50 Hz

delta/star-11 connected, door type, transformer (rating as

specified below), oil immersed ONAN cooled, complete

with all fittings such as oil conservator, silica gel breather,

thermometer, explosion vent with on Load Tap changing

(OLTC) arrangement on HV side with Tapping for variations

of high voltage from (+) 5% to (-) 15% in steps of 2.5% each

with integrated microprocessor based RTCC Panel, bi-

directional roller, diagrams & rating plate, Oil temperature

indicator, & Winding temperature indicator, Buchholz relay,

weather proof Marshalling Box, lifting lugs, first filling of oil,

weather proof H.T/L.T cable box etc. complete as per

specification. All relays, contacts & CT terminals to be wired

upto marshalling box. Transformer shall be as per latest

IS:1180, 1 Star.

2.0 11 KV H.T. CABLE:

Supplying of 11 KV grade aluminium conductor, cross linked

polyethylene (XLPE) insulated individual core screened, flat

steel/strip armoured PVC sheathed cable complete as

3.0 DIESEL GENERATING SET: 625 & 250 KVA

Design, Manufacturing, Supply, Receiving, Unloading,

Shifting, Storing, Installation, Testing and Commissioning of

Radiator Cooled DG sets of following capacity (rating in

kVA) compact packaged silent type, with Outdoor type

Acoustic Enclosure to reduce the noise level as per

requirements of central pollution control board, 415Volts, 3

phase, 50 Hz AC alternator coupled to diesel engine with

Electronic Governer Suitable for Auto Load Sharing and

Auto Synchronizing System complete with all accessories,

standard specifications tool kits, service manual, self

starting device, fly wheel, coupling with guard, V velt,

radiator, instrument panel (starting switch with key, Water

Temperature indicator gauge, Lub OIl Pressure gauge,

Lube oil temperature gauge, Battery Charging Ammeter,

indicating lamp, hour counter etc., residential silencer,

common bed plate, anti vibration isolation pads, extended

cable termination box, grouting bolts, first charge of engine

oil, gear oil, high speed diesel oil, 24 volt maintenance free

chargeable battery set with Trickle/Boost Battery charger,

interface card for BMS connectivity complete as required of

rating 415 Volts, 3 phase, 50 Hz. AC alternator coupled to

Diesel Engine complete with all accessories. NOC from

concerned goverment authority for installation and operation

of D.G. set shall be taken by contractor.

3.1 625 KVA D.G. Set with suitable capacity of day oil fuel Tank

with PCC 3.3 or equivalent as per CPWD specification &

Latest CPCB regulation. Set 0 0 1 1 6156621 0 0 6156621 6156621

3.1.1 250 KVA D.G. Set with suitable capacity of day oil fuel Tank

with PCC 3.3 or equivalent as per CPWD specification &

Latest CPCB regulation. Set 0 0 1 1 3690123 0 0 3690123 3690122.67

3.2 EXHAUST PIPE & CHIMNEY 0 0 0 0

EXHAUST PIPE 0 0 0 0

Supply, installation, testing and commissioning of following

sizes MS exhaust piping heavy duty conforming to IS: 3589

complete with all accessories such as bends, flanges,

stainless steel flexible bellows etc as complete as required.

3.3 Providing & Fixing of Insulation of Exhaust Pipe with

rockwool of min 75 mm thickness min. 64 Kg/m3 density

and 26 SWG Aluminium cladding

3.4 Supply, Fabrication, & erection of MS structure for

supporting of DG emission, exhaust piping with RCC

foundation and in cable trench for cable support etc.

4.0 SAFETY EQUIPMENT 0 0 0 0

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

4.1 First aid box as approved by St.John Ambulance Brigade

/Indian Red Cross society conforming to IS : 2217 - 1963.

4.2 Shock treatment chart duly mounted on a wooden frame

with glass on, as required in 2 languages (Hindi & English).

4.3 Rubber mat 1000 mm. Wide to withstand 1.1 KV, 2.0 mm

thick dielectric strength as per latest IS 15652-2006.

4.4 Rubber mat 1000 mm. Wide to withstand 11 KV, 2.5 mm

thick dielectric strength as per latest IS 15652-2006.

5.0 EXTERNAL LIGHTING WORK- 0 0 0 0

5.1 Supply, Installation, Testing & Commissioning of 6 Mtr

High hot dip Galvanized Octagonal Pole with bottom

130mm A/F, top 70 mm A/F made up of 3 mm thick HT

plate and 220x220x12 mm base plate and 1000 mm long

single arm bracket type GLDG 1024 complete with 4 Nos

M20 x 700 mmlong " J type " foundation bolts, RCC

foundation etc as complete as required. Each 0 0 5 5 16841 0 0 84205 84204.55

5.2 Supply, Installation, Testing & Commissioning of 7 Mtr

High hot dip Galvanized Octagonal Pole with bottom

150mm A/F, top 75 mm A/F made up of 3 mm thick HT

plate and 240x240x12 mm base plate and 1000 mm long

single arm bracket type GLDG 1024 complete with 4 Nos

M20 x 700 mmlong " J type " foundation bolts, RCC

foundation, light mounting bracket etc as complete as

5.3 Supply, Installation, Testing & Commissioning of 16 Mtr

High hot dip Galvanized Himast suitable for 8 nos 120 watt

LED light, ring, gear etc as complete as required.

5.4 Supply, Receiving, Unloading, Shifting, Installation, Testing

& commissioning of Bollard Light 170 mm dia, 780 mm

height made out of cast aluminium lighting fixture, glass

diffuser, stainless steel screw, extruded aluminium poles,

corrossion & UV resistant coation of 1 x 18 watt CFL (TC-

5.5 Supply, Receiving, Unloading, Shifting, Installation, Testing

& commissioning of gate light 1 x 70 watt SON as per

5.6 Supply, Receiving, Unloading, Shifting, Installation, Testing

& commissioning of spike light 1 x 50 watt GU-10 Light with

lamp of approved make.

5.7 Supply, Installation, Testing & Commissioning of LED street

light fixture 36 watt, integral driver, protection IP 65, CLASS

I as complete as required. Each 0 0 5 5 12051 0 0 60255 60255.05

5.8 Supply, Installation, Testing & Commissioning of LED light

fixture 120 watt, 12800 lumen, clour cool white , integral

driver, protection IP 66, CLASS I as complete as required.

5.9 Supply, Installation, Testing & Commissioning of Smart LED

wall bracket light fixture , 1500 lumen, as required.

5.10 Supply, Receiving, Unloading, Shifting, Storing, Installation,

testing & Commissioning of 28 watt solar LED light fixture

with pole , solar panel, battery for 36 hour backupas per

S.H.-IX UPS SYSTEM

1.0 Supply, installation, testing & commissioing of 40 KVA UPS

in paralleling mode at 0.99 input power factor with SNMP

card as per specification given in the document with

following broad features.

THD(i) shall be less than 3% in the entire loading range.

Input power factor shall be more than 0.95. from 25% to

UPS shall carry design output at 40 deg.

S. No. DESCRIPTION OF ITEM UNIT LOWER RATE LOWER

UPPER BMT FLRs TOTAL UPPER BMT FLRs (NON DSR)

Shall have soft start and hold of for incoming supply.

Invertor capability to supply 150% load for 5 sec.

Three Phase Input and Three Phase Output. (Input - 340V -

470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three

Phase, 4 Wire.)

Shall not allow deep discharge of the battery and shall not

go to 10.5 volts in case of 12 volt cells.

SMF Battery shall be external type with rack and suitable for

30 minute backup on 100% load.

UPS shall be compatible for minimum 2 nos unit in parallel

operation. (Synchronize). Parallel operation kit shall be

supplied with UPS.

3.0 Supply installation , testing & Commissioning of following

rating of invertor with battery and trolley as complete as

required. Invertor shall be suitable for 90 minute backup on

full load as per spercification.

TOTAL OF UPS SYSTEM CARRIED OVER TO

S.H.-X SOLAR SYSTEM

1.0 SOLAR PHOTO VOLTAIC POWER GENERATION

Supplying installation testing and commissioning of 40 KW

Grid interactive roof top solar photo voltaic power

generation system including PV solar panel structure, Grid

Tie Inverter, AC & DC cabling, Cable Termination, earthing

system etc as complete as required. KW 0 0 2 2 2789384 0 0 5578768 5578768.12

Net metering for 40 kwp solar system No 1 217921 0 0 217921 0

TOTAL OF SOLAR SYSTEM CARRIED OVER TO

FIRE FIGHTING WORKS

ABSTRACT OF COST

S. NO. DESCRIPTION AMOUNT (DSR-2022) AMOUNT (NSR)

FIRE FIGHTING WORKS

1 FIRE PUMPS, EQUIPMENT, PIPING, VALVES & ACCESSORIES - 82,66,640.00

2 FIRE HYDRANT SYSTEM - 36,63,293.00

3 SPRINKLER SYSTEM: - 45,13,860.00

4 FIRE EXTINGUISHERS & GAS FLOODING SYSTEM - 10,25,318.70

5 ELECTRICAL PANEL ROOM GAS SUPPRESSION SYSTEM - 3,42,643.00

TOTAL (DSR+NSR) 178,11,754.70

Digitally signed by

PRADYUMNA MUKHERJEE

BOQ FOR FIRE FIGHTING WORKS

S.NO. DESCRIPTION OF ITEMS TOTAL QTY. UNIT RATE

SECTION B- FIRE FIGHTING WORKS.

SUB HEAD I - FIRE PUMPS, EQUIPMENT, PIPING, VALVES & ACCESSORIES :

1.0 NSR Electric Motor Driven Hydrant / Sprinkler Pump/ Water Curtain Pump (Location - Plant Room) :

Supplying, installing, testing and commissioning of Fire authority approved Electrical driven fire pump

suitable for automatic/ manual operation consisting of the following:

Horizontal split casing, high pressure single/ multistage centrifugal type fire pump running at 1450 RPM

complete with gland packing, proper connection to suction and delivery line, and including bypass

arrangement for testing of pumps, having a name plate indicating suction, delivery, head, discharge,

stages, RPM and direction of rotation.

Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65 %

of rated head. The shut off head shall not exceed 120% of rated head.

Squirrel cage, induction motor, TEFC type, efficiency class. eff-1, suitable for 415 + 10%V, 3 phase, 50

Hz, AC supply, of suitable HP rating for the above pump with asynchronous speed of 1450 RPM

conforming to IP 55 protection & class 'F' insulation. The motor shall conform to IS 12615 : 2004 and

IS 325 : 1978 (up to date) with flexible coupling and coupling guard.

Common base plate for mounting pump and motor fabricated of mild steel channel as per

manufacturer's recommendation with heavy duty Anti Vibration pads (6 Nos., heavy duty).

Suitable reinforced cement concrete pump foundation as per manufacturer's design including

foundation bolts, washers as required.

v) Flexible Coupling and coupling guard for direct coupling of pump and motor.

vi) Drain Pipe with Valve (50 mm dia)

Rate should include interconnection cables and foundation bolts, grouting of Foundation bolts and

other accessories required.

b) NSR 2 Main Fire Pump

Discharge : 2850 LPM

Pumping Head : 100m

Motor H.P. (Approx) : 100 HP or As per manufacturer

recommendation.

2.0 NSR Diesel Engine Driven Fire Pump [Stand by pump] (Location - Plant Room) :

Supplying, installing, testing & commissioning of fire authority approved Diesel Engine driven fire pump

suitable for automatic/manual operations consisting of the following :

Horizontal split casing, high pressure single centrifugal type fire pump running at 1500 RPM complete

with gland packing, proper connection to suction and delivery line, and including 80 mm bypass

arrangement for testing of pumps, having a name plate indicating suction a delivery head, discharge,

stages, RPM and direction of rotation.

Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65%

of the rated head. The shut off head shall not exceed 120% of rated head.

Heat Exchanger Water cooled diesel engine of required BHP or as per manufacturer recommendation

ii) at 1500 RPM for the above pump complete with standard accessories & suitable cooling system as

described in specifications.

Common base plate for mounting pump & engine of required strength manufactured out of M.S.

iii) channels as per manufacture's recommendation with heavy duty Anti Vibration pads. (Cushy foot) (8

nos., heavy duty).

iv) Flexible Coupling & coupling guard for direct coupling of engine & pump.

Suitable reinforced cement concrete pump foundations as per manufacturer design including

foundation bolts, washer as required.

1 No. 8 hours capacity day oil storage tank fabricated from 3 mm thick M.S. plates. Tank shall be

provided with inlet, outlet, overflow, air vent, drain connections, filling connection & magnetic level

vi) indicator. Tank shall be mounted on a suitable steel structure (Painted with 2 coats of red oxide paint).

Tank shall be provided with epoxy coat from inside & two or more coats of synthetic enamel paint

outside over two coats of red oxide primer. Diesel storage tank shall be double skin.

24 volts 180 AH lead acid battery (12 volts - 2 Nos) with boost/Trickle charger for starting the engine

automatically complete as required.

Rate should include inter connecting cables & foundation bolts, grouting of Foundation bolts and other

accessories required.

a) NSR 3 Diesel Engine Pump

Discharge : 2850 LPM

Electrical Motor Driven Jockey Pump

(Location - Plant Room) :

Supplying, installing, testing & commissioning of fire authority approved electrically driven Jockey pump

suitable for automatic/manual operation consisting of the following:

Horizontal / Vertical mounted multistage jockey pump having cast iron body, S.S. impeller, stainless

steel shaft with gland packing with running at 2900 RPM including bypass arrangement (with 25 mm

i) GM stop valve and up to 5 meter G.I. class 'C' pipe) for testing of working of the pumping set as

required. The pump should meet the recommended requirement and must be approved by the local

fire authority.

Squirrel cage induction motor suitable for 415 + 10%V, 3 phase, 50 Hz, AC supply of suitable HP rating

ii) for the above pump with asynchronous speed of 2900 RPM T.E.F.C type having effliciency class eff-1

as per IS 12615 : 2004, connected to pump with flexible coupling and coupling guard .

Common base plate for mounting pump and motor fabricated of mild steel channel as per

manufacturer's recommendation with heavy duty 4 Nos. Anti Vibration pads.(Cushy foot)

Suitable reinforced cement concrete pump foundations as per manufacturer's design including

foundation bolts, washers as required.

v) Drain pipe with valve (25 mm dia)

vi) Rate shall include inter connecting cables, grouting of Foundation bolts and other accessories required.

a) NSR 4 Jockey Pump

Discharge : 180 LPM

Pumping Head : 100m

Motor H.P. (Approx) : 15 HP or As per manufacturer

recommendation.

Providing, fixing, testing and commissioning of precharged air vessel (size 450 mm dia & 1500 mm

height) fabricated shell from 8 mm thick & dished end 10 mm thick M.S. Plate for pressurization of

hydrant/ sprinkler system complete with adequate pressure switches (as per design / requirement) with

valve to operate as per operating sequences including 25 mm dia drain valve, air release valve with

ball cock on top, 80 mm dia flanged inlet with isolating valve duly painted from inside and out side

complete as required.

Providing, fixing, jointing, testing and commissioning of heavy duty (class 'c') MS pipe conforming to IS :

1239 (Part I) pipes up to 150 mm dia with all necessary fittings like tees, elbows, flanges, reducers,

gaskets, nuts and bolts etc. welded or screwed joints as required including fixing the pipe with

necessary structural supports including painting of two coats of synthetic enamel paint over two coats

of red oxide primer including all civil breakage’s and making good the same, GI Pipe sleeve of suitable

6.0 NSR higher size shall be provided whereever the pipes are crossing the walls/ floors and sealing the sleeves

with glass wool in between & fire sealant compound at either end all as per project Manger/

Consultants requirement including cutting holes and chases in brick, RCC work. All hangers, clamps

brackets etc shall be of galvanized Iron unless specified other wise and then supply of the same shall

be included for the rates under this head. Welding of any kind on the galvanized support / hanger shall

not be permitted including synthetic enamel paint of approved make over a coat of zinc.

Providing, fixing, testing & commissioning of heavy duty MS pipe class 'C', IS : 3589 marked with all

necessary fittings like tees, elbows, flanges, reducers, gaskets, nuts and bolts etc. welded or screwed

joints as required including fixing the pipe with necessary structural supports (for delivery/suction

manifold related to the pumps) including painting of two coats of synthetic enamel paint over two coats

of red oxide zince chromate primer including all civil breakages and making good the same [Location :

a) NSR 16 200 mm dia (6 mm thick) with necessary supports etc. as required. 15 15.00 RM 7,730.00 1,15,950.00

b) NSR 17 250 mm dia (6 mm thick) with necessary supports etc. 15 15.00 RM 8,868.00 1,33,020.00

Providing, fixing, testing & commissioning of flanged end basket strainer made from MS body with

8.0 NSR bottom and top removable flanges with nuts, bolts etc having filteration area at least 6 times the cross

sectional area of the pipe.

Providing, fixing, testing & commissioning of C.I. Butterfly valve conforming to IS : 13095 with flanges,

nuts, bolts and washers complete for following sizes :- [PN 16 rating)].

g) NSR 25 200 mm dia (Gear operated) 2 2.00 Each 54,138.00 1,08,276.00

Providing, fixing, testing & commissioning of C.I. dual plate non-return valve [PN 16 Rating (16 kg/cm

10.0 NSR pressure rating)] complete with 2 nos. matching flanges, rubber insertion, with nuts, bolts and washers

etc of following sizes .

Providing & fixing dial type (150 mm dia) pressure gauge with isolation ball valve suitable for working

11.0 NSR 32 pressure of 250 PSI cost shall be of inclusive of providing any short pieces, nipples, elbows etc as 32 32.00 Each 3,207.00 1,02,624.00

required. having calibration of 0-15 Kg/cm2.

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators

12.0 NSR suitable for raw water up to 45oC temperature, working pressure 8.8 Kg/cm2 and test pressure 20

Providing, fixing water flow meter on test line complete with all accessories for flow indication ,

monitoring & testing of fire pumps with bypass arrangment including piping & bypass valves.

Providing, fixing, testing & commissioning of M.S. class 'C' diesel pump exhaust pipe including all

fittings like bends, tee, clamps/structural steel support of suitable dia for the engine . The insulation of

the exhaust pipe shall be carried out with rock wool with specific gravity of 100kg/cm2 and cladded with

22 gauge aluminium sheet complete with all fittings & accessories.

Providing & fixing pressure switch for water pumps to start/stop the filter feed pump at set pressure.

15.0 NSR 39 Including wiring, cabling from pump to panel & all other accessories as required to operate the system 5 5.00 Each 6,168.00 30,840.00

16.0 NSR ELECTRICAL WORKS:

16.1 NSR FIRE FIGHTING ELECTRICAL PANEL:

Supply, installation, testing and commissioning of following fire fighting panel suitable for 415V, 3

phase, 4 wires, 50 HZ power distribution system. The panel shall be free standing floor mounting sheet

metal sheet inclosed dust and vermin proof conforming to IP-52, Compartmentalized design, fabricated

out of 14SWG sheet steel, painting, earthing numbering, danger plate as per specifications and

drawings, flush front with Aluminium busbars, separate earth to be provieded throughout the length of

16.1.1 NSR the panel. The incoming and outgoing feeder breakers, fuses, indicating lamps etc shall bne

accommodated in modular multitier arrangement. The painting shall done as relevant IS codes/as

specified in the specifications. Adequate size cable alley shall be provided al round the panel and in the

back for each cable bending and termination. The panel shall be fabricated by TAC/Fire authority

approved vendor. The outgoing feeders inside the panel shall be connected through solid bus bars.

Flexible cable links are not acceptable.

Bus bars shall be provided with heat shrinkable sleeves and shall be colour coded . The panels shall

be suitable for cable entry from top. The minimum fault rupturing of all incoming and outgoing

switches/breakers shall be 35KA. The panels shall be fabricated after the approval of fabrication

i) For Wet Riser, Sprinkler & Water Curtain Pumps

ii)For Jockey Pumps

Supply, installation, testing and commissioning of non draw out Cubical type sectinalised floor

standing powder coated switch board of 31 MVA fault capacity at 415 V complete with 4 strip, 800 A

capacity Aluminium Bus - Bar Electrolytic grade, cable alley & supplying & fixing of following

switchgears as per specifications including connections & interconnections.

(i) One (1) No. 630 A TPN MCCB (35KA).

(ii) 800 Amps Aluminium bus bar shall be insulated with heat shrinkable sleeves and shall be coded.

(iii) Three (3) Nos. current transformer (630/5A).

(iv) One (1) No. ammeter (0-600) Amps with selector switch.

(v) One (1) No. (0-500V) voltmeter with selector switch.

(vi) 1 Set (3 Nos.) of phase indication lamps with HRC fuses.

(vii) Indication for control supply 'healthy'.

(i) Three (2) Nos. 400A TPN MCCB 35KA.

(ii) One (1) 40A TPN MCB 10KA

Three (2) Nos. Star Delta Starters complete with over load realy with single phasing protection feature.

(iii) On / Off & TRIP, indication lamp, contactors, ammeter with suitable C.T's suffcient nos. of potential free

spare contacts, etc. Suitable for 100 HP Motor.

(iv) Pressure Switch.

(v) Wiring from pressure switch to starter - Lot

One (1) No. DOL Starter with over load relay with single phase protection feature. ON/OFF & TRIP,

(vi) indication lamp, contactors, ammeter with suitable C.T's sufficient nos. of potential free spare contacts,

etc, suitable for 10 Hp motor.

(vii) One (1) No. pressure Switch.

(viii) Wiring from pressute switch to starter -Lot

(ix) Set of control system to make the system automatic as per functionl as requirements.

Provision for starting the diesel engine fire pump with battery charger for trickle & boost charging. The

(x) diesel engine driven fire pump shall start automatically in the event of pressure dorop beyong preset

limit on mains faulure or failure of electrical driven pumps to start.

(xi) Pressure Switch.

(xii) Wiring from pressure switch to Diesel engine control panel.

Note:- CABEL CONNECTION

(i) Control Scheme as per specification

(ii) Following provisions to be made in the fire panel:

Audio visual alarm & indications having disconnect/reset facility with a range of 1/2 km. Annunciator to