8326 SPECIAL REPAIRS TO BUILDING NO 195 C NO 36 42 OF RAC DEPARTMENT AT NAVAL DOCKYARD MUMBAI

Amount

Demolition of cement concrete un-reinforced in ground floors and paving n exc 15cm thickness below or above GL complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for for below GL complete all as specified and directed.

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers including taking down existing steel tubing and connection complete all as specified and directed

S&F 20mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl the holes in walls and floors shall be made by drilling with drill or jumper and not by dismantling the brick/concrete and made good with CM 1:3 properly including taking down existing steel complete all as specified and directed

M&L for 25mm thick cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in floor complete all as specified and directed

Dismantling of wall ceiling board (fibre, pulp, insulation, etc) or insulation board / slab/ blankets, any thickness,including cover fillets complete all as specified and directed.

S&F GI (Cold rolled) snap grid size of 600mm x 600mm frame work of 24x38x0.6mm, Tee section (bottom pre-coated) and 24x24x5mm thick angle alongwith the wall incl suspenders as per manufacturer's instuction as in ceiling with asbestos free calcium Silicate designer board 4mm thick complete all as specified and directed. (Make : Gabson eternit/Everest )

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing) and rubbish off the premises complete all as specified and directed.

M&L Non skid ceramic coloured tiles 8 to 10 mm thick (Square/rectrangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc over and including 15 mm thick cement screed bed in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No. 09 here in before but as on vertical surface such as skirting, dados and risers over and including 10mm thick backing coat in CM 1:4

M&L Non skid ceramic coloured tiles 7 to 8mm thick (Square/ rectrangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc over and including 15 mm thick cement screed bed in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface size of each tiles 350x250x7mm/ 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situation complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brick work work with old size subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement plaster on brick work or stone walls, etc incl raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surface or surface other than fair face of brickwork in 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of stone wall surface with water proofing compound @ 2% by weight of cement and finished surface even and smooth without using extra cement in CM 1 :6 complete all as specified and directed. (Note:-WPC compound shall be paid separately).

M&L for 100mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub-base of floors all as specified and directed.

S&F Solid PVC door frame of size 50mmX47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet (edges will be painted to match with prelam sheet) reinforced with MS square tube, supplying & fixing in opening as per specification complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6mm raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specified.

S&F 100mm size butt hinges extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed type C-21 etc complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed on door shutter complete all as specified and directed.

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed.

M&L for 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

M&L Stainless steel wire cloth 0.36mm nominal dia or wire and average width of aperture 1.40mm and fixed with stainless steel wire stap complete all as specified and directed.

M&L for Cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting n exc 10cm girth. pinning in, making good to facings where required and pointing in CM 1:3 on stone walls complete all as specified and directed.

S&F in repair 15mm bore brass bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (weight not less than 400gms) complete all as specified and directed.

S&F 15mm bore stop cock (Concealed type) CP fancy type with, screwed down, high pressure for iron pipes or for unions fixed in repairs (weight not less than 400gms) complete all as specified and directed.

S&F CP pillar tap cast copper alloy chromium plated fancy type high pressure with or without lettered hot or cold with long screwed shank and fly nut screwed for iron pipe 15mm dia fancy type (weight not less than 400gms) complete all as specified and directed.

S & F in repairs white vitreous china washed down water closet pan, (pedestal pattern), white, with and including P/S trap, PVC solid type seat cover etc complete all as specified and directed.

S&F vitreous china wash basin, oval shape, white, size 550 X 400mm incl brackets or beding in cement mortar to wall complete all as specified and directed.

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580 X 440 mm white, with integral foot rests incl flush pipe, provn of lime concrete bedding complete all as specified and directed.

M&L Sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, incl bedding in cement mortar to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm bowl size 410mm X 160mm complete all as specified and directed.

S&F 75mm dia CP shower rose swivel type with & incl 460mm long brass CP heavy duty, fixed in repairs complete all as specified and directed.

S & F in repair for health faucet (Jet) 1 m long PVC tube with wall hook chromium plated fitted to stopcock 15 mm bore complete all as specified and directed.

S&F in repairs of vitreous china urinal, half stall type complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugs with and including 60 mm brass screws, pointing around urinal back in cement, flush pipes, inlet, outlet etc complete all as specified and directed.

M&L 32mm dia waste coupling, PTMT for glazed ware sinks, basin, etc with long shanks and fly, flange end complete all as specified and directed.

S&F 10 ltrs capacity PVC low level flushing cistern valve less white or coloured with inlet, ball valve float and handle incl brackets complete all as specified and directed.

S&F PVC connection on pipe 450mm long with brass nut bolt complete all as specified and directed.

S&F PVC waste pipe 32mm dia 800mm long with socket suitable for WHB/Sink complete all as specified and directed.

S&F 75mm dia of outlet cast iron floor trap with grating including jointing to waste pipe in cement concrete (1:2:4), type B-1 complete all as specified and directed.

S&F Brass chromium plated tubular towel rail 600mm long between flanges, 20mm dia, D type etc complete all as specified and directed.

S&F PVC (SWR) Pipe single socketed in any length with rubbering joints laid in trenches or in floor for 110mm dia complete all as specified and directed.

All as per Srl item No 46 here in before but 75mm dia

S&F PVC (SWR) Pipe single socketed in any length with rubbering joints 110mm dia fixed to walls with clamp complete all as specified and directed.

All as per Srl item No 48 here in before but 75mm dia.

S&F PVC Bends any redius 110mm dia provided with access door complete all as specified and directed.

All as per Srl item No 50 here in before but 75mm dia

S&F PVC (SWR) Junction single T equal or unequal 110mm dia provided with access door complete all as specified and directed.

All as per Srl item No 52 here in before but 75mm dia

M&L 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) incl finished even and smooth with using extra cement as in plinth protection incl necessary form work to edges complete all as specified and directed.

M&L RCC 1:2:4 (nominal mix) type B1 (using 20mm graded stone aggregate) as in landing, cooking platforms, shelves and the like complete all as specified and directed.

M & L RCC 1:2:4 (nominal mix) type B1 (using 20mm graded stone aggregate) as in chajjas complete all as specified and directed.

M&L for providing precast cement concrete (RCC) nominal mix, 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc), chullah hoods, chajjas, water troughs mangers, shelves and similar articles with plain faces and setting in cement mortar 1:4 complete with joints to match including necessary form work complete all as specified and directed.

M&L for Use and waste of formwork to soffits of suspended slabs, landings, shelves and similar work n exc 200mmm thick horizontal or sloping complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over cut to length bend to shape as required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410-O or Fe 310-O complete all as specified and directed.

All as per Srl item No 59 here in before but 6 to 8mm dia bars

M&L two coats of synthetic enamel paint over a coat of pink primer on newly wood/wood based surfaces over 10cm width or girth incl preparation of new surface complete all as specified and directed.

M&L One coats of synthetic enamel paint on old painted wood/wood based surfaces over 10cm width or girth incl preparation of old painted surface complete all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of red on steel surfaces over 10cm width or girth incl preparation of new surfaces complete all as specified and directed.

M&L One coats of synthetic enamel paint on old painted steel surfaces over 10cm width or girth incl preparation of old surfaces complete all as specified and directed.

M&L for two coat of oil bound distemper over 2mm thick of birla white putty including preparation of newly surface etc complete all as specified and directed.

M& L for complete removal of existing treatment and applying one coat of Oil bound distemper over 1mm thick birla white putty including preparation of surface.

M&L for Cutting into existing manholes for connecting new drains,making good to pipe and rendering,cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished,and reforming benching as required complete all as specified and directed.

S&F mild steel framed work such as in frames gates, grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, framed balusters, walk ways, railings, framework of water tank and similar work conforming to Fe-290. Gde E-165 complete all as specified and directed.

M&L for Complete removal of existing water proofing treatment of any description in any position including cleaning, wire brushing, watering, removal of debris upto 1500 mtr distance complete all as specififed and as directed.

M&L PCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining roof/chajja slope complete all as specified and as directed.

M&L for brushing neat cement slurry with 3 Kg of cement per square meter all as specified and directed.

M&L for applying oil bound primer @ 0.40 Litre/Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg/Litre at 25 degree celsius on the prepared dry roof surface and provide and lay 4mm thick APP modifed water proofing membrane reinforced with non-woven polyster matt with physical properties as given in particular specification. The laying shall got be done through authorized applicator of manufacturer as specified in paticular specifications. Provide over the membrane finishing with two coats of solar reflective bituminous aluminium paint @ 0.10 Kg/sqms prescribed by manufacturer of membrane including Ten years guarantee on prescribed from complete all as per particular specification, manufacturers instructions and as directed by Engineer-in-Change. Note : Rate including to taking down and re fixing of existing lightning arrestor system including provision of new PCC block for damaged PCC block complete all as specified and directed.

M&L for rendering 20mm thick cement plaster in CM (1:3) on roof top surface finished even and fair including WPC by weight of 3% of total cement concrete complete all as specified and as directed. [Note : WPC shall be measuerd and paid separately]

Supply only integral water proofing compound.

M&L for cement concrete tiles 25cmx25cmx22 mm thick, machine pressed, (with grey cement & pigments) set jointed and pointed in neat cement slurry in floors over and including 15mm thick bedding layers in CM 1:3 all as specified & directed by Engr-in-Charge.

M&L for Complete removal of New treatment of walls and applying two coats of acrylic (antifungal) exterior grade paint of over one coat of primer on wall/roof including scaffolding complete all as specified and directed

M&L for Complete removal of existing treatment of walls and applying two two coats of acrylic (antifungal) exterior grade paint of over one coat of primer on wall/roof including scaffolding complete all as specified and directed

M&L for Making the Chajjah tops surface clean, free from dust dirt, grease, oil, followed by applying 2 coats of approved Rubberized / polymer water proofing treatment POLY ALK WP or equivalent of approved make as per the manufacturer’s specifications as specified and directed.

M&L for taking down, chipping and removing the loose, split, damaged cement concrete, cement mortar surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement, wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned rebar surface wash the rebar with clean water for removing all rusts from the old rebar surfaces, fixing new reinforcement for strengthening the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortar in CM 1:3 mix , 40mm thk in two coats, using polymer as per manufacturer's instructions complete all as specified and directed. Make : Dr. Fixit/Sunanda/chemestik/Fosrok Note:- (New reinforcement and MS Sections will be measured and paid separately)

Material & labour for providing and applying jacketing around columns / beams / other RCC members with Micro concrete (Molith-MC) including all lifts, shuttering, drilling holes and fixing shear anchor / deficient reinforcement as per manufacturer's specification complete. Note: Reinforcement shall be measured and paid separately. (Rates quoted shall be including jacketing, formwork and micro concrete). Make :- Dr. Fixit, STP, Fosroc as approved

S&F welded steel wire fabric, cut to length, fixed to steel members / reinforcement steel, weight per Sqm not exc. 4 Kg.

M&L for preparation of existing surfaces of roof top, RCC Gutter and parapet wall, crack filling with prime seal chemical and cement @ the ratio of 1:4, applying two coats of water proof chemical (Newcoat of dr. fixit or equivalent) and finally applying a coat of SBR latex and silicon powder paste not less than 2 mm thick complete all as specified and as directed.

M&L for providing grouting 12 mm dia holes of 75mm deep @0.6 m c/c at junction of beams and columns as co-ordinal points for inserting/pouring mixture of Lw+, high proof chemicals and cement slurry by pressure grouting for column, beams and slabs, including sealing the holes with CM 1:3, all as specified and as directed.

M&L for micro concrete works in repairs of patches like edges, chajjas, lintels and other RCC members etc complete all as specified and directed.

Supply only polymer SBR Latex or equivalent as approved. Make:- Dr. Fosrok, Sunanda, Dr. Fixit

M&L for erection & dismantling of MS tubular double scaffolding (H frame) upto height of 30m & with necessary brazing, provision of necessary safety equipment to the skilled workers to carry out the work and covering with green cloths for carrying out external face work of walls all as specified and as directed.

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets / power) complete with switches, sockets, ceiling roses, lamp holders, brackets & other fitting & Fixtures connected, and making good to disturbed surfaces complete all as specified and directed.

Taking down old U/S tube light fittings single / Twin, Recess mount fitting , etc and making good the disturbed surface matching with existing surface all as per directed.

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuity conductor connected to common earth dolly with and including modular box with cover plate frame in any module ( Make : Schneider Elect/Legrand Mosaic/Anchor Ave) complete for One light/fan/bell point controlled by one 5A switch complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One Exhaust fan point controlled by one bell push

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts (ISI marked), FRLS grade drawn through & including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuity conductor connected to common earth dolly for 15 Amp swich socket on independent board with and including PVC moulded box with cover plate complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Switch socket measured & paid separately.

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm size, 1100 volts (ISI marked), FRLS grade drawn through & including non metalic rigid, PVC non metallic Conduit, ISI marked, not less than 25mm dia with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuity conductor connected to common earth dolly with and including PVC moulded box with cover plate complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Switch socket measured & paid separately.

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One Exhaust fan point controlled by one 5 amp switch

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts (ISI marked), FRLS grade drawn through & including non metalic rigid, PVC non metallic Conduit, ISI marked, not less than 25mm dia with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuity conductor connected to common earth dolly for 15 amp swich socket on independent board with and including PVC moulded box with cover plate complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - Green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Switch socket measured & paid separately.

Supply and fix switch sockets combination 5 pin 5 Amps flush type 240 Volts AC all as specified and directed. Make: Anchor/Roma/Legrand.

Supply and fix in replacement switch socket combination multi purpose 3 pin 15 Amps controlled by one switch flush type 240 Volts AC all as specified and directed. Make: Anchor/Roma/Legrand.

S & F in replacement of fan regulator electronic step type socket size and making all necessary connections all as specified and directed. Make: Anchor/Roma/Legrand.

S & F in replacement of Ceiling rose, PVC/polycarbonate insulated body type, 3 terminal, 240 volts, 5 Amps all as specified and directed. Make: Anchor/Roma/Legrand.

S & F in replacement 20 Amps Single pole and neutral enclosure with a Two Pin and earth plug and socket complete with one single pole MCB and making connections complete all as directed. Make -Legrand Cat Part No. 5078 14 or equivalent in Siemens /GE/ C&S

S & F in repairs LED light fitting 20W, 230 V, 4 feet surface mounted, indoor decorative aluminium extruded T- 5 LED batten, integrated type etc., complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos including connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed. Make- C & S cat part No. LTTB4F20WLED/W (Nakshatra series) or equivalent cat part in Crompton/Wipro /Philips

S &F in repair Ultra slim edge lit type recess mounting LED 2X2 Luminaire 36 watt and extruded aluminium housing with anti-glare diffuser provides high quality ecomonic energy saving lighting LED Luminaire suitable for 600 x 600 mm modular/POP/Gypsum ceiling complete all as specified and as directed. Make: Crompton cat No LCPL-36-CDL(2X2) / C&S cat No LTCRSLM36WATT2X2 or equivalent Cat part in Surya / Philips

S & F in repairs 120 watt flood light (ORION SERIES), PDC aluminium housing with aim & adjustable bracket, Matt finished reflector for glare elimination, SMD LED with secondary lens, IP65 with high power LED's as light source, suitable for high lighting architectural façade highmast and general purpose complete with all acessories and fixing arrangement all as specified and directed. Make- C & S CAT Part No.- LTEF120WHPLED BAYLIGHT or equivalent Cat Part in Philips/ Havells

S & F in repairs LED Street light 90 Watt (INDUS SERIES) PDC aluminium housing with sealed toughened glass cover, SMD LED with secondary lens complete with all acessories and fixing arrangement all as specified and directed. Make- C&S CAT PART NO-TESS90WLED/LS or equivalent Cat Part in Philips/ Havells

S & F in repirs 120 WATT LED Highbay/Mediumbay LED IP65 luminaire (CORVUS-E SERIES) with high efficiency, PDC aluminium housing with polycarborate diffusers dedicated mounting eye bolt complete with all acessories and fixing arrangement al as specified and directed. Make- C & S CAT Part No.- TEHB120WHPLED/LS/WOR or equivalent Cat Part in Philips/ Havells

S & F in replacement of MCB 0.5 to 4 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make- Legrand/Siemens/GE

S & F in replacement of MCB 6 to 32 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make- Legrand/Siemens/GE

S & F in replacement of MCB, SPN 40 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make-Legrand/Siemens/GE

S & F in replacement of MCB, SPN 63 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make-Legrand/Siemens/GE

S & F in replacement of MCB, 4 Pole, 63Amps capacity, C Curve type suitable for 415 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make - Legrand cat No 4087 02 or equivalent in Siemens/GE .

S & F in replacement 63 Amps Triple pole and earth enclosure with a three pin and earth plug with socket complete with one single pole MCB and making connections complete all as directed. Make -Legrand Cat Part No. 5078 64 or equivalent in Siemens /GE/ C&S .

S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 5076 41 or equivalent in Siemens /GE/ C&S

S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 5076 42 or equivalent in Siemens /GE/ C&S

S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting TPN 8 way, 440 voltsvolts with copper bus bar rating 100 Amps for each phase with 2 neutral bar, dust and vermin proof suitable for incorporation of MCB’s etc complete all as directed. Make - Legrand cat part no 607737 or equivalent in Siemens /GE/ C&S NOTE FOR ITEM No. 108 to 110 : [i] MCB DBs shall be concealed in wall wherever possible including making good the surface to match with surrounding. [ii] The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quoted rate)

M&L for sub-main wiring with 2 runs of 4.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade non metallic PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unserviceable sub main wiring and making good the disturbed surfaces/location complete all as specified and directed.

M&L for sub-main wiring with 2 runs of 6.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade non metallic PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unserviceable sub main wiring and making good the disturbed surfaces/location complete all as specified and directed.

M & L in repair street light wiring with single run 4 Sqmm 3 core core multistranded PVC insulated & unsheathed copper conductors 1100 volts FRLS grade ISI make drawn through & including PVC non metallic conduit with Accessories fixed on wall/ceiling/pole etc including one run PVC insulated & unsheathed multistranded copper conductor 4Sq. mm FRLS grade ISI make as earth continuity conductor connected to common earth as earth dolly

S & F exhaust fan of sweep 300 mm heavy duty type complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230 Volts single phase 50 Hz AC supply and connecting up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection and fixed by using 4 Nos 200 mm long 12 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 completed all as specified and directed. Make: Havells/CG/ Khaitan

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25sq mm 3½ core, laid in duct / along pole/wall etc including making connection including taking down old unsv XLPE cable of any size complete and making good the disturbed surface matching with existing surface complete all as directed. Make of wire : Polycab/ Havells/ Gloster / Plaza Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level connected and incl galvanised earth lead using 25 x 4 mm GI Strip by means of nuts & bolts, check nuts and washer of galvanised incl PCC (1:2:4) type B-1 cover reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25mm x 25mm x 3mm excavation and earth work in any type of soil, charcoal dust, salt light grade GI watering pipe 20mm dia with funnel and wire-mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES sch 2009 (part-I) connected main switch board all as specified and testing on completion .

OM SAI POWER SYSTEMS

Garima Construction Co

RAJENDRA CONSTRUCTION

Shree Ayyappa Engineering

ASHOK CONSTRUCTION

Nexus Infratech