REPAIR/REPLACEMENT OF INTERNAL ELECTRIC WIRING FITTING / FIXTURES GARDEN LIGHT AND METER PANEL INCL ITS CONNECTED ITEMS AT SALARIA OFFICERS ENCLAVE UNDER GE WEST DELHI CANTT- 10

Amount

Taking down carefully point wiring (light/fan/socket/power/call bell) complete from existing concealed conduits and making good the disturbed surfaces of wall/floors/ceiling etc) and all modular flush box ,frame plate and switch socket fitting fixtures deposited to MES store Yard complete all as specfied and as directed.

M&L for point wiring with 3x1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable (phase, neutral and earth wire) in existing concealed conduit, earth wire connected to common earth dolly. Existing pressed steel sheet Metal sunken box and modular frame plate ,switches ,Sockets are fully intact at site and need not to be replaced under this items, this item includes only replacements of the light point/5 Amp independent board point/power point circuits wire (phase,neutral,earth) at site all as directed. Work to be completed carefully without damaging any existing items. Note: (a) Site will be available in peace wise/completely to contractor as per availability. (b) Any damage/breaking of wall surfaces to be make good by the contractor without any extra cost and make the surface match with the existing colour and texture of walls.

One light/fan/bell point controlled by one way switch 5 amps.

One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

One Two Way switch point controlled by 2-two way switch 5 amps.

All as per item No. 2.00 here-in-before but with 2x2.5 Sqmm and 1x 2.5 sqmm cable for earth connection for one 2 pin socket outlet 15 amps independent board in existing conduit complete all as specfied and as directed.

All as per item No.2.00 here-in-before but with 2x4.00 Sqmm and 1x 4.00 sqmm cable for earth connection for AC/Geyser points in existing conduit complete all as specfied and as directed.

Supply, laying and drawing submain wiring in existing concealed PVC rigid conduit in walls 02 runs of IC x 10.00 sqmm (Main Cable and neutral) and one run of IC x 10.0 sqmm (as earth wire) of stranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including taking out old wiring connection making good surface of distubed area complete all as specfied and as directed.

Taking down ceiling/exhaust fan, ceiling cable end, dismantling blades and removing fan and blades to store and refixng the same complete all as specfied and as directed.

M&L for rewinding of ceiling fans of any type and make complete with super enamelled copper wire (HTP) in the workshop wire with appropriate gauge suiatble for existing make including necessary lathingmon shaft, both sides of rewinding covered with high quality varnish, replacement of ball bearing of SKF/NBC make and provisions of new nuts and pins for 1200/1400 mm sweep including taking out old burnt wind of copper/aluminium complete all as specfied and as directed.

Supply and fix in repair exhaust fan motor up to 300 mm copper windings as per sample complete all as specfied and as directed.

Supply and fix in repair PVC Fresh air fan motor 300 mm copper windings as per sample complete all as specfied and as directed.

M&L in repair louver shutter made out of GI sheet suitable for exhaust fan 300 mm sweep size at the height from 3mtr to 6 mtr height making good surface of distubed area dully fixed with gitti,pech.screw with all accessories complete all as specfied and as directed. Note: Contractor shall arrange suitable T&P including necessary form work, scoffolding and safety measures to make it functional complete all as specified and directed.

Supply and fixing in repair of Incomer 160A FP MCCB 25KA Microprocessor Based with O/L & S/C and E/F (LSIG) Protection (Make: Schneider/ ABB/ Siemens) along with Aux. (1NO+1NC)+ Trip for 160A FP MCCB (set of 2) with IFM or equivalent MODBUS Interface Module for 160A FP MCCB (Make: Schneider/ ABB/ Siemens), BSCM (Breaker Status and Control Module) for 160A FP MCCB (Make: Schneider/ ABB/ Siemens) with 1.3m NSX cord for 160A FP MCCB dully fixed in LT panel complete all as specfied and as directed.

Supply and fixing in repair of Outgoing 63A DP MCB 10KA C-Curve (Make: Schneider/ Siemens/ ABB) for residential flats in block. The outgoing shall be enabled with Energy sensor, PowerTag Monoconnect (or equivalent) 16A 1P+N top position and smartlink or equivalent modbus converter (Make: Schneider/ Siemens/ ABB) dully fixed in LT panel complete all as specfied and as directed.

S&F in Replacement of Copper Heating Element 2000 watt suitable for Geyser make Bajaj model Montage of 25 Ltr capacity as per sample complete all as specfied and as directed.

S&F in Replacement of thermostat suitable to work at water temperature 30° to 75° C electric cut up suitable for Geyser make Bajaj model Montage of 25 Ltr capacity as per sample complete all as specfied and as directed.

Supply and fix in repair metal plug top 20 Amps 3 pin 230- volts complete all as specfied and as directed.

Supply and fix in repair metal plug socket 20 Amps 3 pin 230- volts complete all as specfied and as directed.

Supply and fix in repair SS braided pipe of 12 mm (internal dia) suitable for hot/ cold water, with brass nuts and rubber washers complete all as specfied and as directed.

Supply and fix in repair MCB SPN 63 Amps, 10KA, 240V, 'C' series complete all as specfied and as directed.

Supply and fix in repair MCB SP 6-32 Amps,10KA,'C' series complete all as specified and as directed.

Supply and fix in repair LED batten luminaire surface mounted 2 feet system wattage of 10 watts and system lumen ≥100 output ,CRI > 80, power factor > 0.95, THD < 10%, color temperature 3000K- 6500 K , IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specfied and as directed.

Supply and fix in repair LED batten luminaire surface mounted 4 feet system wattage of 20 watts and system lumen≥100 output ,CRI > 80, power factor > 0.95, THD < 10%, color temperature 3000K- 6500 K , IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specfied and as directed.

Supply and fix in repair 10 watts bulkhead fitting with powder coated die cast with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is ≥100 lm/W , Power Factor >0.95, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<10%, CRI>80, Color Temperature 3000K-6500K, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specfied and as directed.

Supply and fixing ceiling fans in repair complete with blades, down rods, with remote and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specfied and as directed.

Supply and fixing ceiling fans in repair complete with blades, down rods, with remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specfied and as directed.

Supply and fix exhaust fan in repair made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specfied and as directed.

Supply and fix in repair decorative, wall mounting, champagne gold finish fixtures with plastic body with acrylic cover suitable for 9 Watt led lamp B22 base complete all as specfied and as directed.

Taking down carefully old rusted meter panel along with MCCB -01 No, MCB SPN/DP -04 nos , and taking down & refixing of 04 Nos Smart meter in new metering panel complete all as specfied and as directed.

Supply and fixing in repair of a polycarbonate type metering panel board (make: Rittal, Takachi, Hensel, Schneider) dully designed for mounting one nos of 160A MCCB (incomer), and 4 x 63A DP MCBs (out going), 01 x DDC Controller and 04 Nos Smart energy meter for consolidated residential building monitoring and recording of parameters with panel specifications as below: The board/panel shall be made out of modular Polycarbonate of suitable size to accomodate the following alongwith a tariff meter which shall be environment friendly, recyclable, UV resistant, halogen & silicon free, anti- acid & anti corrosive, Glow Wire test for 960 deg. Cent. The manufacturer of panel shall submit a copy of test report, Degree of Ingress Protection IP 65 in accordance with IEC 60529. The gasket material shall be Polyurethane, while the gasket shall be internally embedded. The manufacturer of board/panel shall submit a copy of type test report in accordance with respective IECs for power switchgear and control gear assembly. The technical parameters shall be as follows: Type of Enclosure: Polycarbonate Bus bar: 160A Copper Degree of Protection: IP 65 System Voltage: 415V, 50Hz Finish Shade: Enclosure & accessories RAL 7035/ or as approved by the GE Installation: Indoor/Wall Mounting Note :- (a) MCCB/MCBs/DDC will be measured and paid separately (b) Four Nos of Electric meter obtained from taking down of LT panel to be fixed in this panel properly dully making all the connections

Supply and fixing in repair of water level sensors capable of measuring the water level in tank having depth upto 1m. Said water level sensors shall have following parameters: Media: Liquid Material: SS and PTFE IP Protection Class: IP68 Max Overload: 150% Communication interface: RS485 Modbus Burst Pressure: 300% Accuracy: +-0.5% FS/year Power Supply: 24V/ 230V Ambient Temperature: 85 Degree capable of transmitting and recieving measured live date signnals wirelessley to DDC Wherein the said water level sensor shall be wired with the ddc type controller in the meter board of the building tower to communicate level data every 15min/ 30min/ 1 hr (customizable)

Supply, Installation, Testing and Commissioning of Residential facility Management System software. The said software shall have dashboards and screens for monitoring of MCCBs, MCBs, Metering and water level sensors (Make: Schneider, Siemens, GoPower, RightWatts, Regin) a) Must have user customizable dashboards and SLD (without any coding/ scripting). Dashboards shall be enabled with SVG based mimics only (PNG, JPEG images for functional mimics shall not be allowed) b) Multi-site data viewing within same interface without any physical cable connection of sites to single website c) System must be accessible over internet and must have adequate security with dual factor authentication with username/ password along with OTP on email. d) All device communication with the server must be secured using TLS/SSL encryption. Central System must not support non-secure connections.

Supply and fix in repair LED LAMP 9 Watts pin type including taking any type of lamp complete all as specfied and as directed.

Supply and fix in repair canopy for ceiling fans (Set of two) complete all as specfied and as directed.

Supply and fix in repair ceiling fan capacitor for 1200/1400 mm sweep 2.5 mfd complete all as specfied and as directed.

Supply and fix in repair modular switch 5A ,indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular switch 15A indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular socket 5A, 5 pin, indo Asian as per sample complete all as specfied and as directed.

Supply, Installation, Testing and Commissioning of reporting software plugin for the following: Periodic reporting shall be enabled according to the format decided by the engineer-in-charge. All runtime/ development licenses must be included in the above for creation and maintenance of the system. The same shall be installed on a workstation/ personal computer and shall have the following functionalities. (1) The central system software will report online trend for monitoring and should be capable of controlling devices. It should have all basic functionalities such as monitoring, historian (For trend analysis), alarm generation, and reporting. (2) The software with various reporting options and can store minimum 12 months of data. (3) The software have bidirectional operation on at least on MQTT, Modbus and Bacnet protocols and shall have more than 5000 tags. It must support SVG and PNG formats of assets.

Supply and fix in repair modular fan regulator 1 module indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular socket 15A, 2 in 1 indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular bell push 5A indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular two way switch 5A indo Asian as per sample complete all as specfied and as directed.

Supply and fix in repair modular cover plate 3 module as per sample complete all as specfied and as directed.

Supply and fix in repair modular cover plate 4 module as per sample complete all as specfied and as directed.

Development, Programming, Testing and Commissioning of all Building management software screens, Annual Reporting Modules, Alerts and Alarms as follows: 1. Programming and development of schedulars to ensure that local jobs are not down; and to kickstart the same. Development of site-based scheduling algorithms for the same. 2. Reports as per MES requirements to multiple mailboxes. The module shall be self programmable with training and support. Programming, configuration and customisation of the Smart Platform with respect to the residential facilities module as per actual site conditions and requirement of the engineer. Creation of Day wise Reports for :- (i) MCCB and MCB working status (ii) Individual meter monitoring of each household from MCB extension terminal. Monitoring of each water level sensor. (iii) ON/OFF/Trip status of each MCB/ MCCB (iv) Configuring notifications and alerting. (v) Consumption Patterns - Daily, Weekly, Monthly and Annual reports for the following must be provided.

Supply and fix in repair call bell electric 240 volts, AC supply, Ding Dong type complete all as specfied and as directed.

Supply and fix in repair ceiling rose3 phsae pvc/polycarbonate isolated body complete all as specfied and as directed.

Supply and fix in repair PVC flexible two core copper 1.5 sqmm size complete all as specfied and as directed.

Supply and fix in repair Single core copper conductor 1.5 sqmm size complete all as specfied and as directed.

Supply and fix in repair Single core copper conductor 2.5 sqmm size complete all as specfied and as directed.

Supply and fix in repair Single core copper conductor 4.0 sqmm size complete all as specfied and as directed.

Supply and fix sheet metal enclosure MCB distributioon board single pole and neutral 2 way 240 volts complete all as specfied and as directed..

M&L for Providing PCC 1:2:4 type B-1 20 mm graded aggregate for GI tubing post for pathway light pole complete all as specfied and as directed.

Supply and fix in repair MCB SPN 16 Amp "C " curve complete all as specfied and as directed.

Supply and fix in replacements Aluminium extruded epoxy grey powder coated garden light aesthetic design for most effective thermal management ,injection moulded opal poly carbonate diffuser provide uniform glare E37 free garden light with inbuilt LED 12 watts and driver, IP 66, LM 79, LED make Osram/Seoul/, CRI≥75, , Luminaire Efficacy≥ 100lm/watt, rated voltage 240V,50 Hz, Light wattage 12 watts THD @ 240V ≤ 10 % , BIS Approved, Aluminium Extruded pole length 800mm dully fixed in PCC and making connection complete all as specified and directed. MAKE- Prima Nx model No PGBL-12/ Equivalent K-light/BAJAJ/Philips

Supply and lay cable PCV insulated screened PVC bedded, multistranded copper conductor wire of size 1.5 sqmm 3 core 1100 volts , dully fixed in Rigid PVC Conduit Pipe on wall/ ground complete all as specfied and as directed.

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3323628)