Special repair to SMC and certain revenue works at Air Force Station Jaisalmer

Amount

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc or for shafts, wells cesspits, menholes, pier holes, laying of cables and pipes lines etc not exceeding 10sqm on plan and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engineer-in-Charge. Note :- Approved soft soil suitable for filling in floors shall be brought by the contractor from outside MD land.

15mm thick plaster in cement mortar (1:6) on stone masonary surface or other than fair face of brick work or concrete surfaces or stone masonry surfaces of wall, finished even and smooth without using extra cement including taking down old cement plaster complete all as specified.

10mm thick ceiling plaster in cement and sand mortar (1:3) on uneven faces of concrete surfaces of ceiling on fair and finished even and smooth without using extra cement and including taking down old cement plaster complete all as specified and directed.

Praparation of newly plastered surfaces and applying one layers ready mixed wall putty on entire surface of wall/ceiling to smooth finish surfaces with appropriate sand paper and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of newly plastered surfaces or unplastered surfase of walls and applying two coats of distemper oil emullsion over a coat of chalk whitening complete all as specified and directed.

Preparation of old decorative surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed.

Complete removal of existing treatment, filling up undulation and applying one layer of ready mixed wall putty on entire surface of wall/ceiling to smooth finish surfaces with appropriate sand paper and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of old decorated plastered surfaces of ceiling surfaces by washing, rubbing down and stopping of distempered and painted sufaces and applying two coat of distemper oil emulsion of any tint etc complete all as specified and directed.

Preparation of old surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of cement based paint in different tints on surfaces of wall any colour as approved by GE complete all as specified and directed.

Preparation of old decorated wall surfaces of any description and applying one coat of oil emulsion distemper of any tint etc complete complete all as specified and directed.

Preparation of old decorated surfaces of ceilings of any description and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted wooden surfaces or wood based materials of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

Preparation of old painted steel surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint any colour as approved complete all as specified and directed.

Preparation of newly or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of newly plastered surfaces or unplastered surfase of ceiling surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) as in ground floors, copings and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified

100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring/hard standing/paving finishing cement concrete surface fair and even complete all as specified and directed.

40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring, finished even and smooth with using extra cement complete all as specified and directed).

100mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring, finished even and smooth with using extra cement complete all as specified and directed).

PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in parapets, copings and like including weathering slightly rounded or chamfered angles and throating, necessary formwork as required etc complete all as specified and directed.

Precast cement concrete (1:3:6), type C-1 (using 20 mm graded stone aggregate) solid block masonary exceeding 10cm and set in cement and sand mortar (1:6), complete all as specified and directed.

Precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, chajjahs water troughs, mangers, shelves and similar articles with plain faces including use and waste of form work and set in cement sand mortar (1:6) complete all as specified & directed.

Machine cut kota stone flooring 20-25mm thick laid in floors in squares or rectangular pattern over and including 15mm thick cement screed bed in cement and sand mortar (1:6) set and jointed neat cement slurry and pointed in coloured cement to match the shade of the slab including rubbing and polishing including dismantling floor, hearth or wall tiling and cement mortar bedding complete all as specified

Machine cut Kota stone slab 20 to 25mm thick, as in skirting, riser of step, dado and pillar etc. laid over and including rendering of 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling floor, hearth or wall tiling and including cement mortar bedding complete all as specified and directed.

Vitrified Ceramic Tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement and sand mortar 1:6 including dismantling floor, hearth or wall tiling and cement mortar bedding complete all as specified.

Coloured Non Skid Ceramic Tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc over and including 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match including dismantling floor, hearth or wall tiling and cement mortar bedding complete all as specified and directed.

Coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc over and including 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match and including 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sub base of flooring complete all as specified and directed

Coloured glazed ceramic tiles of size 450x300x7mm or 300x200x7mm thick on vertical surfaces, dado and skirting over and including 10mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile including dismantling floor, hearth or wall tiling and cement mortar bedding complete all as specified and directed

Seamless calcium silicate ceiling made out of 1800x1200x12mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at including hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with Gl cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.20m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including taking down existing complete all as specified and as directed.

12mm thick perforated particle board/tiles for insulation and accoustic purposes, 600mmx 600mm in size, fixed with screws to timber frame work or with staples on snap grid in ceiling, flat or sloping including taking down existing complete all as specified and directed.

Vitreous china squatting pan 'Orissa Pattern' of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with P' or 'S' trap complete including jointing and making good to floor with provision of PCC 1:5:10 bed including taking down existing complete all as specified and directed.

Vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic PVC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinges device including taking down existing complete all as specified and directed.

Vitreous china urinal, full stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60mm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe including taking down existing complete all as specified and directed.

Vitreous china wash hand basin white flat back of size 550x400mm with including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10x7.5x15cm with and including 32mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange including waste pipe fixed complete all as specified and directed.

Vitreous china wash hand basin white flat back of size 550x400mm with 40x40x5mm angle iron brackets duly painted with synthetic enamel paint including cutting for and pinning in ends of brackets and embedded in PCC 1:3:6 type C-1 blocks of size 10x7.5x15cm with CP pillar tap fancy type copper alloy with capsten handle scrubbed down high pressure screbbed shanks and fly nuts screwed for iron pipe 15mm dia PVC connection 450mm long with PTMT nuts high pressure ncluding 32mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange fixed complete all as specified and directed.

PVC valve less syphonic action type, 10 litres capacity low/high level flushing cistern, white with inlet, ball valve float and handle including brackets fixed to wall with bracket and screwed including PVC flush pipe including taking down existing complete all as specified and directed.

Sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm including taking down existing complete all as specified and directed.

Sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed.

15mm bore fancy type chromium plated pillar taps with long nech/swan neck with elbow operated handle, screwed down high pressure with long screwed sharks and fly nuts screwed down for iron pipes complete all as specified and directed.

Chromium plated Hand Shower (Health Faucet) with 1.0 to 1.50 metre long flexible tube & wall hook and anodised hanging device complete all as specified and directed.

Chromium plated Jet spray with flexible tube 1.0 to 1.50m length complete all as specified and directed.

15mm bore fancy type, chromium plated Bib taps with elbow operated handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

15mm bore fancy type, long body, chromium plated Bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

200mm bore Reinforced concrete pipe, class NP-3, laid and jointed complete with collars including taking down existing complete all as specified & as directed.

Taking up or down steel water tubing including connected fitting, fixture land specials and disconnection of fitting such as stop valve bib tap etc including cleaning of pipe for re-fixing or removal to store of size 15 to 40mm bore complete all as specified and directed.

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings complete fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Galvanized steel water tubing medium grade of 32mm bore with & including all fittings complete fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Galvanized steel water tubing medium grade of 40mm bore with & including all fittings complete fixed to walls and ceiling or laid in floors, complete all as specified and directed.

15mm bore fancy type with two way angle cock, cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified and directed.

15mm bore fancy type chromium plated stop valves/angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed including taking down existing complete all as specified and directed.

15mm bore fancy type chromium plated stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

20mm bore Gun-metal globe or gate valves (ISI marked), with iron wheel head, screwed both ends for iron pipe and fixed including taking down existing complete all as specified and directed.

PVC connection suitable for 15mm bore with PTMT nuts of 600mm length including taking down existing complete all as specified and directed.

32mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

40mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cemented complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 22.5cm and not exceeding 30cm long and dia of neck 16 to 20mm complete all as specified and directed.

Rolled mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe-410), quality 'A' complete all as specified and as directed.

4mm dia plain mild steel wire, galvanized class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. (each line of wire to be measured) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 5mm dia to 10mm for stirrups, bent to shape required, including cranking, binding spirraly for hoppijng for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Mild steel for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, conforming to Fe-290 (Gde-E-165) drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete including necessary welding etc and fixing in position complete all as specified and directed.

Mild steel flat as in hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

1.00mm thick mild steel, plain, black sheet in wall cladding, steel gates, etc., cut to size, holes punched including rounded headed screws, clout nails or revets and fixed to wood or steel framing or fixing to MS clamps with necessary bolts and nuts with plain 40mm lap joints welded to frame including taking down existing complete all as specified and directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium snap beading complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and including taking down existing complete all as specified.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down existing complete all as specified and directed.

75mm bore PVC (SWR) bends any radius provided with access door including taking down existing complete all as specified and directed.

PVC (SWR) floor trap dia of outlet 75mm, with grating including jointing with solvent cement for trap including taking down existing complete all as specified and directed.

Cutting openings through stone masonry walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed.

Cutting holesin exceeding one brick wall but not exceeding two brick walls, stone masonary built in cement mortor for inserting hold fasts and making good dismantled portion in cement concrete (1:2:4) type B-1 complete all as directed and directed.

Cutting of existing 15mm bore steel tubing for alteration or additions (Each cut measured) necessary done in position without taking down complete all as specified and directed.

Taking down frame with shutters (without taking off shutters from the frames), area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified and directed.

Anodised aluminium extruded sections, expanded metal mesh, as in frames for doors, windows, ventilators, partitions with one or more rebates including necessary joining cleats, glazing clips, rubber neoprene packing for fixing, anodised aluminium snap beading screws complete all as specified and directed. Note:- (i) The rate quoted under this item deemed included for necessary jointing cleats, glazing clips, aluminium beading, screws, rubber packing, locking device in built handles, roller for sliding window.

100mm Butt hinges medium weight, cold rolled mild steel ISI marked complete all as specified and directed.

125mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified.

125mm long mild steel pressed handles ovel type stove enameled black complete all as specified and directed.

150mm long Aluminium handle cast type, anodized complete all as specified and directed.

200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and directed.

200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

250mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked including taking down existing complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in door, overall length of cover plate 150mm complete all as specified and directed.

Mortice lock brass, vertical type, size 100mm 4 lever complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, with & including replacement of floor tiles if any broken during repair work and making good surfaces matching to the existing including taking down existing complete all as specified and directed.

Taking down and refixing aluminium door/window shutter not exceeding 2.50 sqm each in the same opening after repair/replacement/changing defected/unservicable of anodised aluminium section, handle, locking device, roller including necessary joining cleats glazing clips, rubber neaprene packing, anodised aluminium snap beading screws etc. complete all as specified and directed. Note:- (i) The rate quoted under this item deemed included for necessary jointing cleats, glazing clips, aluminium beading, screws, rubber packing, locking device, in built handles, roller for sliding window etc & fitting of old glass. However, no element on account of weight will be taken into consideration for these items. (ii) Section of aluminium for repair/replacement shall be provided as per existing paid for separatly and glass, wire mess will be paid for seperatly.

Double legged informatory sign board of size 1.20mx1.20m fixed on single frame, both side and meeting back to back on the stainless steel 50x50x3.65mm square pipe. The board are of high intensity grade reto-reflective sheeting of avery dennison made out of 2 mm thick alcoband sheet/aluminium sheet confirming is 736,colour as approved by Engg-in-charge and stainless steel square pipe of size 50x50x3.65mm with nut and bolt. The letter writing will be computerised cut to high intensity grade white sheeting (Avery Dennison) and mechanically fixed on board over verticle post 50mm stainless square pipe, 3.65 mm thick 3.20 m long having 2 Nos flat iron strip of strip 40x5 mm, 0.30mm long on bottom and fixed with PCC 1:3:6 in post holes of size 450x450x750mm complete all as specified and directed.

500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water storage tank complete all as specified and directed.

Point wiring for one light point controlled by one, one way 6 Amp switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non metalic rigid PVC conduit 20mm dia with accessories fixed to cutting chases in walls by cutter and making good surface in cement and sand mortar 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surfaces conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes (as per site requirement) including providing new 3mm thick plastic laminated sheet cover (Hylem) including taking down existing point wiring complete all as specified and directed. Note: (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor/Formica including machine screws and washer etc for fixing switches sockets etc including 1.5 sqmm copper conductor, strandad (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified.

All as per serial item No. 97.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No. 97.00 here-in-before but for one 3 Pin, 6 Amps, socket outlet controlled by one 5/6 Amps switch on independent board.

All as per serial item No. 97.00 here-in-before but for one 3 Pine, 6 Amps, socket outlet controlled by one 5/6 Amps switch on same board.

Point wiring for one light point controlled by one, one way 16 Amp switch with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non metalic rigid PVC conduit 20mm dia with accessories fixed to cutting chases in walls by cutter and making good the surface in cement and sand mortar 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surfaces conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes (as per site requirement) including provision new 3 mm thick plastic laminated sheet cover (Hylem) including taking down existing point wiring complete all as specified and directed. Note: (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor/Formica including machine screws and washer etc for fixing switches sockets etc including 2.5 sqmm copper conductor, strandad (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified.

Modular switch 6 Amps, 250 Volt, AC, one way, one module (ISI Marked) including disconnecting and taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5734 00 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular switch 16/20 Amps, 250 Volt, Single Pole, AC, one way with indicator one module (ISI Marked) including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5720 63 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Socket shuttered, 6 Amps, 250 volts, 2/3 Pin combined, Single Pole, universal India two module (ISI Marked) including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5734 70 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Socket shuttered, 6/16 Amps, 250 volts, 3 Pin combined, Single Pole, Indian two module (ISI Marked) including disconnecting & taking down existing complete all as specified and directed Make : Legrand (Arteor) Cat Part No 5734 71 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Metal flush mounting box of 3 Module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 6890 08 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Metal flush mounting box of 4 Module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 6890 09 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Metal flush mounting box of 6 Module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 6890 10 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular Metal flush mounting box of 8 Module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 6890 42 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

White colour modular blanking plate, one module blank including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5736 49 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

White colour plates with frame for modular switch of 3 module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5757 20 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

White colour plates with frame for modular switch of 4 module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5757 30 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

White colour plates with frame for modular switch of 6 module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5757 40 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

White colour plates with frame for modular switch of 8 module including disconnecting & taking down existing complete all as specified and directed. Make : Legrand (Arteor) Cat Part No 5757 50 or equivalent in Schneider (Opale)/Anchor(Ave) as approved by GE.

Modular fan step regulator, 120 Watts - 2 module, flush type and connecting up, ISI marked, 240 Volts including disconnecting & taking down existing complete all as specified and directed

Ceiling rose surface bakelite 65mmx17.5mm with two or three terminal PVC/Polycarbonate, isolated body (ISI Marked) including disconnecting & taking down existing complete all as specified and directed

Sub main wiring with 2x4.00 sqmm, single core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) 1100 volts grade conforming to IS 694 and including 4.00 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit including taking down existing sub main wiring complete all as specified and directed. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit.

Surface and wall mounted LED tube light fittings capacity 20 watt, robust and high performance integrated IP20 LED batten to create a sustainable lighting environment with surface/suspended mounting, basic all purpose surface and wall mounted LED batten with luminaire comprises of extruded channel in thermally conductive material. High translucent serrated milky white diffuser to get glare free and smooth light distribution efficacy 110 lumen/watt including taking down existing complete all as specified and directed. Make : Cromton Greaves Cat Part No. CIS-350-40-57-SL-DP-NWH or equivallent in Havells/CG Philips/GE as approved by GE.

Energy Efficient LED street light fittings of 45 Watt, pressure die cast alluminium housing & toughened glass with IP-66 degree of protection, individuals LED's should have lenses for better throw across & along road range 140-280 volts fittings should be provided 5 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, should have lumens output of 110 lumens watt minium protections facility in drivers, driver should be potted type for viberation proof performance & includings making electrical connections including taking down existing complete all as specified and directed. Make: Cromption Greaves Cat Part No. LSTS-45-CDL-M or equivalent in Philips / Orient /Havells / Wipro as approved by GE. Note :- Driver should be BIS registered with "R" marking.

Ultra Modern designed architectural, LED Recessed mounted bottom opening 2X2 LED, CRCA powder coated bousing, Glare free uniform illumination with longer life and less maintenance, luminaire of capacity 24 watt which provides soft-light and suitable for armstrong/grid ceiling including taking down existing complete all as specified and directed. Make : Crompton Greaves Cat Part No. LCBOR-24-CDL or equivallent in Philips/GE/Havells as approved by GE.

Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amps rated copper bus bar 240 Volts, 8 way, SPN DB, suitable for fixing MCB as outgoing and MCCB Triple Pole 100 Amp, rupturing capacity 25 kA as main incoming duly painted including fixing of lugs in main incoming and outgoing line and fixing of cable glands of suitable size including grouting the same in wall by means of nut bolts, angle iron and making good distrurbed surfaces including taking down existing complete all as specified and directed. Make : Standard Cat Part No. DSDNSHODIW08 or equivalent in Legrand/Indoasian /Siemens /Schneider as approved by GE.

Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amps rated copper bus bar 415 Volts, 4 way, TPN DB, suitable for fixing MCB as outgoing and MCCB Triple Pole 100 Amp, rupturing capacity 25 kA as main incoming duly painted including fixing of lugs in main incoming and outgoing line and fixing of cable glands of suitable size including grouting the same in wall by means of nut bolts, angle iron and making good distrurbed surfaces including taking down existing complete all as specified and directed. Make : Standard Cat Part No DSDNTHODIW04 or equivalent in Legrand/Indoasian/ Siemens/ Schneider as approved by GE.

MCCB, 3 Pole, 63 Amps rating, rupturing capacity 16 kA, 415 Volt grade, AC, 50 Hz, Magnetic adjustable thermal fixed type and making connections using suitable size copper lugs/thimbles and crimping tool, including taking down existing MCCB complete all as specified and directed. Make : Indo Asian Cat Part No. 830226 or equivalent L&T/Legrand/ Siemens/HPL/C&S as approved by GE.

MCB, Single Pole with Neutral, 40 to 63 Amp, 240 Volt, repturing capacity 10 kA, ‘C’ Curve, including taking down existing complete all as specified. Make : Legrand Cat Part No. 4086 18 or equivallent Havells/C&S/Standard as approved by GE.

MCB, Single Pole, 40 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 410 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles including taking down existing complete all as specified and as directed. Make : Legrand Cat Part No. 4085 95 or Seimens/Havells/ABB as approved by GE.

Metal clad box with top plug and socket, capacity 10 to 20 Amp and including 20 Amp, MCB Single Pole including taking down existing complete all as specified and as directed. Make : Siemens Cat Part No. 8GB0501RC or equivalent Havells/Legrand as approved by GE.

Exhaust Fan 300mm sweep, BEE approved, ISI Marked with mounted in suitable opening arrangement with louvers and shutters suitable for operation on 240 volts, Single Phase, AC supply and connecting upto including three core PVC insulated PVC sheathed copper conductor flexible cable 23/0.0076 from ceiling rose or connector block including marking of MES number complete all as specified and as directed.. Make : Crompton Greaves/Usha/Bajaj/Orient/Havells as approved by GE.

Ceiling Fan 1200mm sweep, Single Phase, AC supply, 240 Volt, including canopies, three number blades, down rod, double ball bearing with capacitor of 2.5 mfd, and including PVC insulated PVC sheathed copper conductor flexible 3 core cable 23/0.0076 from ceiling rose or connector to fan including marking of MES number complete all as specified and as directed. Make : Crompton Greaves/Bajaj/Orient/Havells as approved by GE. (Note: Length of suspension rod shall be adjusted by cutting, threading as directed and its cost is deemed to be included in rate of hanging of ceiling fan).

Earthing complete with galvanized steel earth plate electrode 60cmx60cm x6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 23 mm thick sand stone slab pit cover including taking down existing earthing complete all as specified & as directed. Note: PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT electric power cable (ISI marked) with aluminium stranded conductor 1100 volt grade cross sectional area 25 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out existing cable complete all as specified and directed.

Schedule 'A' Part-II Price worked out by the Department for **Rs. 22,008.00 “Credit Schedule" as listed in Schedule ‘A’ Part-II on serial Page No. 18 of CA.

deepaktraders