Nagercoil Corporation Providing Partition arrangments at new office building

Amount

Providing Partition arrangments

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Supply and fixing Perculated gypsum board false ceiling using 18 mm thick of approved Quality and design suspended from the ceiling using ‘U’ shaped Galvanised Iron channel of size 25 x 25 x 0.55 mm thick at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing ‘U’ shaped G.I. Channel of size 50 x 30 x 0.55 mm thick at 0.60 m centre to centre on cross direction and fixing of ‘U’ shaped G.I. channel of size 50 x 10 x 0.55 mm thick at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W. reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design/pattern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using kit ply 12 mm thick and opening should be covered with Acrylic panel etc. complete complying with standard specification and as directed by the dept officers. All the materials should be got approved before use work.

Supply and fixing of invertr 1.5 AC

Supply and fixing of Partigle Board Almirah

Supply and Providing of steel Table

Supply and Providing of S-Type Chair

Supply and Providing of Plastic Chair

Supply and Providing of Office Table (AEE Room)

Supply and Providing of Executice Chair (AEE Room)

Supply and Providing of AC Point (AEE Room)

Supply and Providing of Fan Point (AEE Room)

Providing and fixing 600mm depth shelf with doors made to shape, pattern as per drg., and Using 18 mm thick BWP plywood finishing with 1mm thick approved Laminate shown in Architect drawing.The rate shall be inclusive of supply and fixing of ebco or equivalent make hardwares like soft close type hinges,Intermediate Laminate shelves,adhesives and wastages etc, as required to be completed as per standard practice and detailed drawing

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

ARK Construction (BID ID -1181159)