SPECIAL REPAIRS TO BLDG NO P 110 AND OTHER SANCTIONED WORKS UNDER AGE BR 1 AT ITARANA ALWAR

Amount

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) all as specified & as directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying or cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

Material and labour 100 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

Material and labour 75 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L factory made 60mm thick vibratory moulded precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as Specified & directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for precast cement concrete (1:2:4 type B0 using 12.5mm graded crushed stone aggregate) louvers and jallies, 35mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 all as specified & as directed.

Material and labour glazed ceramic tiles (Ist quality) (coloured) 300mm x 450mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) (Ist quality) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular) polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 25 thick cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in levelling coarse for tiles.

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15mm bore Stop valve fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&F 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F 15mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair 15mm bore Two way Angle valve chromium plated screwed plated screwed down,high pressure with capstan heads screwed both ends for iron pipe or for union.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) all as directed.

S&F in repairs PVC connection 750 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete.

S&F salt glazed stone ware gully trap square or round mouthed type 'P' of size 100 x 100 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C1 block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete, all as specified and as directed.

S&F cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified & as directed.

S& F CP grating round type 125mm dia size..

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, Jet spray including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple, complete all as specified & as directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

Supply and fixing as in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repair pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Material and labour brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

M&L for 5mm thick rendering over top of roof slab/chajjas in CM 1:3 mixed with water proofing compound @ 3% by weight of cement or as per manufacturer’s instructions, finished even and smooth without using extra cement all as directed. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 15mm thick in cement plaster 1:4 on stone masonry or bricks or concrete surfaces of walls, finished even & smooth without using extra cement with water proofing compound @ 3% by the weight of cement, ( WPC measured and paid for separately) complete all as specified.

Supply only integral water proofing compound (ISI marked).

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified.Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L rendering 15mm thick in cement mortar 1:6 on surface other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls including 2mm thick white wall care putty all as specified & as directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including white wall care putty (make-Birla/JK/Asian) on walls all as specified & as directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L brooming down old decorated plastered/asbestos cement surfaces of ceilings & applying two coats of white wash complete all as specified.

M&L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L preparation of new untreated wooden surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of pink primer.

Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/chajja etc., removing complete layer of bitumen under concrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment all as directed by Engineer-in-charge.

M&L PCC padding (1:2:4) type B0 using 12.5mm graded stone aggregate over roof slab laid to slope in average consolidated thickness of 50mm and surfaces finished even and smooth without using extra cement complete all as specified.

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 Kg/Sqm conforming to IS : 3384 and applying a layer of APP based polymeric membrane not less than 3mm thick weighing not less than 3.50 Kg/Sqm, reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) and upper side of membrane thermally insulated with white gravel finish uniformly embedded during manufacturing process. It shall be laid by torch application having side over lap 75 mm and at the end 100 mm, all overlaps and joints shall be sealed by torch application. For parapet, membrane shall be taken to a height of minimum 60 cm and inserted inside the parapet in a groove to a depth of 65 mm. The same shall be finished by a membrane flashing. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) complete all as specified

Taking down chowkat or frame with shutters area t exc. 1.5 but not exc 4sqmSqm each (without taking off the shutters from the frame) complete all as specified

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

M & L for Cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3, exc half brick & not exc one brick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)

Supply & fixing factory made ‘Z’ type section steel windows with side hung shutters including box type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) complete all as specified & as directed.

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

Supply and fixing brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified. Make :- Godrej / Harrison / Link

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S&F anodized aluminium grill of approved pattern for windows / ventilators / doors complete as directed and all as specified.

Supply and fixing 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165(Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete. Note : Cost of welding butt hinges to the door frame deemed to included in quoted rate and butt hinges shall be measured & paid for “Supply only” separately under relevant item of this Schedule.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar works of Gde E-165(Fe 290) including welding etc. complete all as specified & as directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified.

M&L welding in repairs exc 2.5cm but not exc 5cm in length, thickness of metal to be welded not exc 6mm, complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, glazing in repairs, complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

S&F 4mm thick frosted glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

Supply and fixing 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply and fixing 100 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.

Supply and fixing 200 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified

Supply and fixing 150 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified

Supply and fixing 150 mm long mild steel pressed handle, oval type, stove enameled black complete all as specified

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type B-21 anodised complete all as specified.

Supply & fixing butt hinges of size 100mm medium weight, aluminium anodised ISI marked complete all as specified

Supply and fixing 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F 6mm thick High Pressure Steam Curved (HPSC), Non asbestos fibre cement building boards in celing flat or slopping, jointless finish with jointing compound and jointing tape as per manufacturer's instructions, fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified & directed.

S&F Anodised aluminium snap grid frame work for false ceiling complete all as specified & directed.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F in repairs stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 20mm bore of pipe.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 15mm bore of pipe.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.

All as per serial item No. 120.00 here-in-above but 8mm dia.

All as per serial item No. 120.00 here-in-above but 6 to 10mm dia in stirrups, spacers and binders.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete (nominal mix) 1:2 :4 type B1 using 20mm graded stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L for formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L for formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

Supply and fixing 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable pipe of any type with fittings and making good around complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors including necessary excavation and earthwork complete all as specified

Supply and fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified

Supply and fixing 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable pipe of any type with fittings and making good around complete all as specified and directed.

Supply and fixing in repair 75 mm bore UPVC (SWR) bends any radius with access door complete all as specified.

Supply and fixing in repair 110 mm bore UPVC (SWR) bends any radius with access door complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F 75mm bS&F 75mm bore PVC (SWR) branch piece, single (Single ‘Y’) equal or unequal.

Supply and fixing CI cowl for 100 mm bore CI pipe complete all as specified

Supply & fixing vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A', ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

M&L cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

Add to (or deduct from) serial item No. 150 here-in-above for each 25mm girth or part thereof over or under 30cm inner girth.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in kerb block with plain fair faces, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

S&F CP toilet paper holder with cover complete all as specified and directed.

S&F Towel rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms).

S&F brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed.

S&F vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F health faucet, brass chromium plated, including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F vitreous china urinal, Silky off white / Ivory, concealed DC, including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including, CP urinal spreader, CP grating and union for discharge pipe including waste pipe complete all as specified & as directed.

S&F 100mm bore cast iron bend (any radius) with duck's foot or heel rest complete all as specified & as directed.

S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

Supply and fixing 100 mm bore cast iron, spun pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors including dismantling

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

Taking down carefully, copper/aluminium unserviceable /perished point wiring any type for light/ fan/ socket or power complete including fittings such as switches, ceiling roses, pendant holders, lamp holders, bracket holders, regulators sockets, light fittings, lamps etc, and making good to disturbed surfaces of wall/floor/ceiling etc, complete, all as specified and directed.

Material and labour for point wiring for one light point controlled by one, one way switch with multistrand 1.50 Sqmm unsheathed copper conductor PVC insulated FRLS cable including continuous earth wire 1.5 Sqmm in green colour unsheathed copper conductor PVC insulated FRLS cable connected to common earth dolly in PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS in on New wooden boards fixed on wall for mounting switch, socket, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete, all as specified.

All as per description of serial item No. 164.00 above but for one fan point controlled by one switch and regulator complete all as specified and directed.

All as per description of serial item No. 164.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp on same board.

All as per description of serial item No. 164.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp independent board.

All as per serial item No. 164.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts.

Supply and fixing switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts.

Supply and fixing socket outlet for 2 & 3 pin, 5 Amp, flush type 240 Volt.

Supply and fixing socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt.

Supply and fixing ceiling rose surface Bakelite 65x50mm two or three terminals.

Supply and fixing decorative ultra slim liner LED lighting fixture with extended polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride and connecting up with and including white coloured flat/round twin core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete, all as specified & directed. Make :- Havells Cat Part No LHEXBLP7PN1W018 or equivalent of Syska / Crompton Greaves as approved by GE

Supply and fixing in repairs sheet metal enclosure, double door type, suitable for fixing MCCBs 100 Amps, TPN with 200 Amps rated bus bar, vertical DB 4 way TPN including incoming MCCB 100 Amps, 415 volts.

Supply and fixing sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 240 volts.

Supply and fixing sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 8 way, 240 volts.

Supply and fixing MCB 32 Amps, single pole & neutral, 240 Volts.

Supply and fixing MCB 6 to 32 Amps, single pole, 240 Volts.

Supply and fixing 2nd class hard wood rectangular block open recessed of size 30x25x5 cm depth with 3mm thick hylum/Bakelite sheet on top grouted with 4 Nos bolts.

Supply and fixing LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make :- C&S Cat Part No LTESS20WLED or equivalent of Havells / Syska / CG as approved by GE

Supply and fixing new fan regulators electronic step up type socket size and connecting up, ISI marked flush type, 240 Volts complete all as specified and directed.

Supply and fixing sub main wiring on and including PVC casing caping, 1100 Volts grade cable, PVC insulated copper conductor and over all PVC unsheathed for sub main wiring multistranded conductor of 6 Sqmm single core cable and earth wire of 6 Sqmm unsheathed copper conductor complete. (Two run of cable with one run of earth wire should measured as one length) including taking down existing unserviceable sub main wiring.

Supply & fixing and testing exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

Material and labour earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, 75 mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 m away from the earth electrode. The pipe for watering shall be provided in slanting manner

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 35 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including taking down old unserviceable cable complete all as specified. .

M & L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M & L for dry sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and directed. Note :- Thickness after punning shall be considered for payment.

Cutting & inserting TEE, L bow , Bend/ Collar and tapping the connection from the existing 50mm GI tubing line for taking branch connections including tapping accessories complete all as directed.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings complete laid in trenches. Note :- Excavation & earthwork shall be measured & paid for separately.

M/s Laxmi Enterprises

M/s ASK Enterprises

M/S JINDAL ENTERPRISES

B.S Constructions

S.S Enterprises