138WE/L-67/24-25

Amount

M&L for 200mm dia MS ERW pipe heavy grade 'C' Class complete heavy grade class, 'C' with welded ends laid in ducts over the angle iron supports/ fixed on the walls including fittings complete all as specified and directed by Engr-in-Charge. (Note : The item rate is inclusive of cutting to any levels/shapes like elbows, tees, bends etc, welding joints wherever necessary as per the site requirement)

All as per item No.1 here in before but of size 150mm

All as per item No.1here in before but of size 100mm

All as per item No.1 here in before but of size 80mm

All as per item No.1 here in before but of size 50mm

All as per item No.1 here in before but of size 40mm

All as per item No.1 here in before but of size 32mm

All as per item No.1 here in before but of size 25mm

All as per item No.1 here in before but of size 20mm

Cutting the existing CI Pipe line any size in position for insertion of new Butterfly valve of size as per ground required directed for tapping out branch connection complerte including joints, ( Note :- Butterfly valve excavation to messured sepperatly)

M&L for replacement of Cast iron Butterfly valve of size 200mm dia Class PN 1.6 with SG Iron Dice flanged ends (integrally cast) horizontal type, conforming to IS-14846 (ISI marked) with stainless steel spindle and iron wheel non rising type including jointing material complete such as rubber or fibre board insertion packing rings with requisite numbers of nuts, bolts & washers etc including taking out existing unserviceable valve complete all as specified and directed.

All as per serial item no 11 here in before 150mm dia

All as Above item no 11 here in before 100mm dia

All as above item no 11 here in before 80mm dia

Taking out the unservicable insulation from MS ERW pipe of size 150mm bore of pipe and providing for Insulation of MS Pipe with PUF slab 40 mm thick and applying bituminuous compound and GI cladding with 26 gauge GI sheet complete including complete earthwork for clearance around the pipe compete all as specifid and as directed.

All as per item No.15 here in before but of size 100mm

All as per item No.15 here in before but of size 80mm

All as per item No.15 here in before but of size 50mm

All as per item No.15 here in before but of size 40mm

All as per item No.15 here in before but of size 32mm

All as per item No.15 here in before but of size 25mm

All as per item No.15 here in before but of size 20mm

S&F in replacement of inlet/outlet forged brass ball valve 20 mm with Y Stainer for FCU, hot water for -25 to 90 degree temperature as per existing, including supply and fixing GI nipple of size 3/4 inch including welding work, cutting the existing rusty unserviceable MS/GI nipple complete including taking out existing unserviceable valve complete all as specified and directed.

S&F and replacement of Inlet/outlet forged brass ball valve 25 mm with Y Stainer for FCU, hot water for -25 to 90 degree temperature as per existing, including supply and fixing GI nipple of size 3/4 inch including welding work, cutting the existing rusty unserviceable MS/GI nipple complete including taking out existing unserviceable valve complete all as specified and directed.

S&F and replacement of Forged steel globe valve, bolted bonnet outside screw & yoke type rising stem for 25mm dia complete including taking out existing unserviceable valve complete all as specified and directed.

All as per item No.25 here in before but of size 40 mm

All as per item No.25 here in before but of size 50 mm

Brass flare nuts of size 20/15 mm bore and fix the brass valves/FCUs including taking out existing unserviceable valve complete all as specified and directed.

S&F in replacement of FCU connection flexible pipe 20/16 mm as per existing, complete all as specified and directed. Make- Jindal/Kitetac or equivalent in ISI marked make as approved by GE.

Material and labour for complete cleaning and checking the serviceability of fan coil unit of any capacity for having continuous sreviceability of FCU for any number of time as desired by Engr-in-Charge including replacement of minor spare part like Gasket, Teflon tape, flare nut, tightening of any loose glycol line connections, shifting FCU from one place to another place if required, heating up the freezed glycol line anywhere about the premices and cleaning with the chemical solution by pressure pump from inlet to outlet to have continuous flow of glycol fluid, repairing the insulation of pipe line of any size by providing shallow tape / GI wire as deemed fit, for fastening the insulation with pipe line, stopping any kind of leakage from any size of pipe line, tightening the loose electrical connections as related with FCU / Heating system, cleaning the air filter including radiator of FCU to the entire satisfaction of Engineer-in- Charge all as directed at site.

S&F in replacement of fan coil unit duel shaft electric motor 1/12 HP, 30 watt 930 RPM, 3 speed as per existing, complete all as specified and directed. Make- Maratan/CEG or equivalent in ISI marked make as approved by GE.

Welding the leakage portion of MS pipe line including earhwork complete and materials as required for welding the pipe line of size 25 mm to 200 mm including testing on full pressure complete all as specified and directed.

M&L for cleaning of MS overhead POL storage tank of capacity 2000 Ltr including all type of T&P and chemical required for the same, including welding work to leakage surface including opening and refixing the existing insulating materials to the external surface of storage tank.

M&L for Pressure gauge 100mm dia, rating 0 to 80 Kg/Sqcm including taking out existing unserviceable gauge complete all as specified and directed. Make :AE/IEBIG or equivalent in ISI marked make as approved by GE.

Material and labour for replacement of old unserviceable centrifugal motor 3 phase 415 volts of capacity 7.5 HP with Mechanical seal complete fittings with accessories , complete all as specified and directed. Make : Kirloskar/Havells//Texmo or equivalent in ISI marked make as approved by GE.

Material and labour for replacement of old unserviceable centrifugal monoblock pump KDI-515+ 3 phase 415 volts of capacity 5 HP with Mechanical seal complete fittings with accessories , complete all as specified and directed. Make : Kirloskar/Havells//Texmo or equivalent in ISI marked make as approved by GE.

Material and labour for replacement of old unserviceable centrifugal monoblock pump 3 phase 415 volts of capacity 3 HP with Mechanical seal complete fittings with accessories , complete all as specified and directed. Make : Kirloskar/Havells//Texmo or equivalent in ISI marked make as approved by GE.

T&P alongwith Labour only for attending of complaint for day to day / daily complaints by employed skilled staff, checking the serviceability of fan coil unit of any capacity for having continuous sreviceability of FCU for any number of time as desired by Engr-in-Charge including replacement of minor spare part like Gasket, Teflon tape, flare nut, tightening of any loose glycol line connections, shifting FCU from one place to another place if required, heating up the freezed glycol line anywhere about the premices to have continuous flow of glycol fluid, repairing the insulation of pipe line of any size by providing shallow tape / GI wire as deemed fit, for fastening the insulation with pipe line, stopping any kind of leakage from any size of pipe line, tightening the loose electrical connections as related with FCU / Heating system, cleaning the air filter including radiator of FCU to the entire satisfaction of Engineer-in- Charge all as directed at site. Note :-(i)Attending any complaints of different nature in a single day in Corps HQ COmplex Plant Room inside / outside will be considered as one job. ii)Any kind of replacement of major items shall be measured and paid for separately under respective item of schedule 'A' iii) . Any nature of complaint related with FCUs, radiators, bursting/cracking/leakage of MS pipe lines, replacement of valves etc will be completed round the clock by suitable trademen (welder with suitable T & P,(including portable heating materials)-01,Skilled mechanic of CHS-01, Plumber/Fitter with helper-each o1, Supervisor-01 as per descreation of Engineer-in- Charge.iv)Job slip will be maintained by the contractor Supervisor under supervision of concerned JE E/M CHS, suitable communication shall be maintained through JE incharge round the clock. v) Any delay in attending complaint will be directly reported to higher authorities and suitable penalities will be incured from the contractor (Rs 1000/-Per job)

Dismantling of burner assembly at HQ 14 Corps CHS and removing of side cover of boiler capacity 10 lakh kilo/cal/hr and complete servicing the boiler including exhaust outlet i.e chimmney by removing the complete carbon/oil deposits with suitable coil shine chemical including repair to coil assembly by welding if there is any leakage found or any other repair required at site and reassembling/ testing the same, complete all as specified and directed.

S&F in replacement of Radiator Coil for 10 lakh kilo/cal/Hr capacity hot water generator not calcified under Indian boiler Act 2023 as per existing shape size & dimension as per manufactures recommendation all as specified and directed by Engr-in-Charge

S&F in replacement of photo cell as per existing suitable for 10 lakh kilo Cal/hr burner rod assembly, complete all as specified and directed.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 7.5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 3 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 2 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

Material and labour for rewinding of electric motor 3 phase 415 volts of capacity 0.5 HP with superior quality super enameled copper winding wire of appropriate size and gauge as existing including varnishing , cotton tape, PVC sleeves etc, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of High pressure fuel pipe 1.5 mtr as per existing, complete all as specified and directed.

S&F in replacement of plug top 15 Amps, 3 pin as per existing, complete all as specified and directed.

S&F in replacement of rotary type ON/OFF switches for Fan Coil unit 22mm dia as per existing, complete all as specified and directed.

S&F in replacement of contactor type MNX 12 (AC-15) : 4A, 415 V, 12 A for 5.5 KW with auxillury contactor MNX-A, A600.P600 complete all as specified and directed by Engr-in-Charge. Make : L&T

S&F in replacement of phase failure relay VSP D1 complete all as specified and directed by Engr-in-Charge. Make : Minilec.

S&F in temp controller digital type Sz-7510P with sensor, complete all as specified and directed. Make- Subzero.

S&F in replacement of over load relay 5A, 240 V AC/5A 28V, DC, 3A 150V, AC. Make - OMRON, LY4 (2873C), complete all as specified and directed.

S&F in replacement of over load relay 10A, 110 V AC, 1/2 HP, 20V AC, 10A 220V, AC. Make - OMRON, LY4 (2282H3), complete all as specified and directed.

S&F in replacement of over load relay 3A, 150V AC/5A 240V, AC, 5A 28V, DC. Make - OMRON, MY4, (2935C), complete all as specified and directed.

M&L for replacement of diesel filter as per existing (upto 1 ltrs) complete all as directed by Engr-in-Charge

S&F in replacement of burner nozzle suitable for 10 Lakh K Cal/Hr complete all as directed by Engr-in-Charge

S&F for sequence controller LOA 24 for burner rod assembly of 10 Lakh K Cal/Hour, complete all as specified and directed . Make- Siemens as per exisiting model

S&F in replacement of Ignition Transformer electronic type suitable for 10 Lakh K Cal/hr burner rod assembly, complete all as specified and directed. Make- Denforce.

M & L for replacement of burner rod assembly single phase 220 volts, Make Bentone Type ST-120, Model-ST-120K, or Equavelent Eco flame Capacity 02-5.6KG/hr, suitable for 10 Lac Kcal/hr boiler complete all as specified and directed by Engr-in-Charge.

Supply, connection and testing of thermal heater wires on water supply pipe lines (GI/MS/PPR) for heating of water through minimum 25 Watt per meter in spiral/ straight line shape above outer diameter of pipe with aluminium tape insulation to preserve heat, fiber glass layer, second layer of aluminium tap to hold fiber glass by glass wool minimum 40mm thick with essential tapes complete. Make: HTC Chromalox or equivalent in ISI marked make as approved by GE.

Supply and fixing and replacement of Chilled/Hot Water wall mounting indoor type Fan Coil Unit 600 /1.5TR (CFM/TR) Capacity incl 02 Nos of 20mm valve with stainer (inlet&outlet) incl heavy duty PVC pipe for connection complete all as specified and directed by Engr-In-Charge. Make : Carrier/Zeco or equivalent ISI Marked as approved by GE

Supply and fixing in replacement of wall mounting (ECO Panel) Convector heater 2.5KW/Hrs Two heat output setup with auto control and LED temperature display. Diemension-Width 1200mm, height, 450mm depth 90mm with complete fixing accessories complete all as specified and as directed.

Supply and fixing and replacement of Chilled/Hot Water Fan coil Unit (FCU) vertical type Floor Mounting 600/1.5TR (CFM/TR) Capacity complete all as specified and directed by Engr-In-Charge. Make : Carrier/Zeco or equvalent ISI Marked make as approved by GE.

Supply and fixing and replacement of Chilled/Hot Water Fan coil Unit (FCU) vertical type Floor Mounting 2400/6TR (CFM/TR) Capacity complete all as specified and directed by Engr-In-Charge. Make : Carrier/Zeco or equvalent ISI Marked as approved by GE

national engineering (BID ID -3125079)

EESSI (BID ID -3102321)