COMPREHENSIVE MAINT OF INTERNAL ELECTRIFICATION CEILING FAN EXHAUST FAN ELECTRIC WATER HEATER DBS EARTHING LIGHT AND CONNECTED ITEMS AT KANJOLI LINE DAYAL BAGH MES IB AT MIL STN BHARATPUR

Amount

Disconnecting & taking down the ceiling fan of any sweep for carry out preventive maintenance and re hanging the same after cleaning the dust etc with air pressure, cotton cloth & brush, taking out ball bearing and bush, cleaning with kerosine oil, lubricating greasing, oiling, cleaning to winding including supply and replacement of nuts, bolts, rubber seal, split pin, connector and copper cable PVC size 3 core 0.5 Sqmm upto required lenght from ceiling rose to connector of ceiling fan including hanging, connecting up and testing complete all as specified.

M&L for 02 X coat of spray painting of ceiling fan of any sweep complete with blades, down rod etc with synthetic enamel paint of approved colour by spraying including filling cavities with filler, preparation of surfaces cleaning all dust etc and writing of MES No of size not exc 5cm thick using black enamelled paint complete all as specified. Note:The cost of disconnecting & taking down fans and refixing after painting is deemed to be including item no.01

M&L for cutting and dismantling the existing winding of ceiling fan of 1200mm sweep and rewinding with super enamelled copper winding wire of suitable gauge including varnishing, lubricating, greasing, oiling and testing including replacement of ball bearing-02 Nos if required complete all as specified. Note:- The cost of bearrings is deemed including in quoted rate.

All as per ser item No 03 above but 1400mm sweep ceiling fans including replacement of ball bearing-02 Nos if required complete all as specified. Note:- The cost of bearrings is deemed including in quoted rate.

following parts/components suitable for ceiling fan 1200/1400 mm sweep Shall be paid as supply only.

(a) Capacitor 2.5/3.15 mfd, oil filled, 400V AC, 50 HZ, 85 degree C ISI marked Make : Asian/Unistar/Usha.

(b) Hanging clamp complete with rubber real Make as existing /sample kept in AGE E/M office complete all as specified.

(c) Fan Hook complete as standard real existing fixed to GI Pipe/Existing Channel complete all as specified.

(d) Ceiling fan blade suitable for ceiling fan of any sweep (set of three blades) complete all as specified.

(e) Down rod 50 cm long 15mm internal dia heavy duty duly painted including clamp, rubber ring, nut and bolts complete with canopy

(f) Down rod 1 mtr long 15 mm internal dia heavy duty duly painted including clamp, rubber ring, nut and bolts complete with canopy

(g) BLDC ceiling fan controller 50Hz,230V, single phase, 2Amp,5kVA surge protector complete all as specified.

Disconnecting & taking down the exhaust/wall fan of any sweep for carried out preventive maintenance and re hanging the same aftercleaning the dust etc with air pressure, cotton cloth & brush, taking out ball bearing or bush, cleaning with kerosine oil, lubricating greasing, oiling, cleaning to winding including supply and replacement of nuts, bolts, rubber real, split pin, connector and copper cable PVC size 3 core 0.5 Sqmm upto required lenght from ceiling rose to connector of exhaust fan including hanging, connecting up and testing complete all as specified. (Note for Srl item No 01 and 6 here in before : (i) Minor parts such as nut, bolt, washer,rubber real, split pin, connector copper cable pvc insulated 0.5 sqmm 3 core are deemed to included with unit rate of item.(ii) Parts/components replaced other than mentioned above will be measured and paid separately under respective items as supply only. (iii) The services of ceiling fan shall be carried out door to door.(iv) After completion of work all fans shall be tested to the entire satisfaction of Engr-in-charge Note:Major item such as capacitor, fan blade etc shall be measured and paid seperately.) as supply only.

M&L for 02X coat of spray painting to exhaust/wall fan of any sweep complete with blades, down rod etc with synthetic enamel paint of approved colour including filling cavaties with filler, preparation of surfaces cleaning all dust etc and writing of MES No of size not exc 5cm height using black synthethic enamelled paintcomplete all as specified. Note:- the cost of disconnecting & taking down fans and refixing after painting shall be deemed to be including quoted rate of item no. 06.

M&L for cutting and dismantling the existing winding of exhaust/wall fan of any sweep with super enamelled copper winding wire of suitable gauge including varnishing, lubricating, greasing oiling testing incl replacement of ball bearing/GM bush as required complete all as specified. Note:- The cost of ball bearing shall be deemed to be including quoted rate.

Supply and replacement of following parts/components suitable for exhaust fan 200-450mm sweep(PVC & Steel ,body) shall be paid as supply only.

(a) Capacitor 4 mfd, oil filled, 400V AC, 50 HZ, 85 degree C ISI marked Make : Asian/Unistar/Usha.

(b) Fan blade set (set of three) for exhaust fan of 380mm sweep complete all as specified.

(c) Fan blade set (set of three) for exhaust fan of 450mm sweep complete all as specified.

(d) Exhaust fan mounting bracket incl nuts,fastners complete all as specified.

(e) Exhaust fan motor of 200-300mm sweep as per existing PVC exhaust fan complete all as specified.

(f) Exhaust fan motor of 380-450mm sweep as per existing steel body exhaust fan complete all as specified.

(g) Louvers and shutters of PVC/ MS as per existing exhaust fan complete all as specified.

Taking down the existing unserviceable water storage type geyser of capacity 25/35/50 ltr by disconnecting from water connection and reinstallation at the same location after carrying out necessary repair/replacement of unserviceable parts such asReset type thermal cut out, fusible plug fuse,Non return valve vertical type spring loaded, ISI marked,Iron neck ring, Brass inlet/outlet assembly complete without element and thermostat,Aperture plate made of brass,Element holding clip made of mild steel,Bolts with washer 25mm long for aperture plate,Rubber gasket, plate type for aperture plate, Indicator bulb square/round type complete with necessary connection wire of red & green colour complete, Pressure release valve of size 15mm, ISI marked, Anti vaccum valve with GI tee of 15mm bore, ISI marked, including one coat of spray painting with synthetic enamel paint and testing complete all as specified.

Supply only following parts required for repair of the geyser water storage type 25/35/50 ltr capacity.

(a) Thermostat switch adjustable type complete all as specified.

(b) Water storage tank made out of SS body with covering of non corrosive protection on both sides of sheet with 100% pure Salem stainless steel sheet/electro statically powder coated body made of min 1.5mm thick CRCA sheet complete all as specified.

(c) Heating element 1500W with rubber ring clamping screws etc complete all as specified.

(d) Heating element 2000W with rubber ring clamping screws etc complete all as specified.

M&L for removing unserviceable grouted "Anchor" type bolts and nuts from the wall and S&F new "Anchor" type bolts (04 Nos of 12mm dia) grouted properly in wall to hold 25/35/50 ltr capacity water storage type geyser with and including nuts and washers and marking good the disturbed surface in cement mortar 1:3 complete all as specified. Note: The cost of taking down of existing geyser is deemed to be included in quoted rate.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc and making good, cutting exc 10cm and not exc 20cm girth in brick or stone wall including making same texture of cutting surface as per existing wall complete all as specified.

Taking up or down the existing unserviceable GI steel tubing and S&F new 15mm bore galvanised steel water tubing, medium grade with all fittings complete to walls and ceilings or laid in floors complete all as specified.

S&F in repair PVC cable 3 core copper conductor of size 2.5 Sqmm to water storage type geyser of capacity 25/35/50 ltr including taking out old cable complete all as specified.

Taking down U/S plug top and S&F new 3 pin plug top 16 amps, 230 volts, ISI marked complete all as specified.

Taking down U/S plug top and S&F new 3 pin plug top 5 amps, 230 volts, ISI marked complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, bell,same board, independent or power) complete fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials and making good disturbed surfaces of wall, floor & ceiling etc complete all as specified.

Dismantling of old U/S sub main wiring and service wire of any size & make complete all as specified.

Dismantling of old U/S rusted main switch/DB of any size capacity and make complete all as specified.

M&L concealed point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe size not less than 20 mm dia with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface and making good the disturbed surfaces of wall/ceiling by means of Wall putty and matching colour of existing wall, PVCsleeve/dash fastners with cadmium plated screws including suitable size of PVC boards/ sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm PVC insulated but FRLS unsheathed copper earth continuity conductor to common earth and connected to earth dolly complete all as specified for the following :-

(a) One light point controlled by one way switch complete all as specified.

(b) One fan point controlled by one way switch complete all as specified.

(c) One 3 pin 6 Amp socket point outlet on the same board complete all as specified.

(d) One 3 pin 6 Amp socket point outlet on the independent board complete all as specified.

(e) One bell/buzzer point controlled by one push button complete all as specified.

(f) One light point controlled by 2 way Switch complete all as specified.

All as per item No 21 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in and including PVC casing and caping double locked box type with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the surface of wall/ceiling by means of PVCsleeved/dash fastners with cadmium plated screws including suitable size of PVC boards for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated FRLS unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly for the following :-

(a) One light point controlled by one way switch complete all as specified.

(b) One fan point controlled by one way switch complete all as specified.

(c) One 3 pin 6 Amp socket point outlet on the same board complete all as specified.

(d) One 3 pin 6 Amp socket point outlet on the independent board complete all as specified.

All as per item No 23 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps switch socket outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified.

S&F ceiling rose surface bakelite three terminal ISI marked including suitable size of PVC board complete all as specified.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type multi purpose flush type 230 volt complete all as specified.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified.

S&F switch piano flush button single pole one way 16 Amps 230 volt grade complete all as specified.

S&F socket 3 pin 16A, flush type complete all as specified.

S&F bell push flush type 5 Amps 230 volts grade complete all as specified.

M&L bell multi musical type 230 volts grade complete all as specified.

S&F in repair step type electronic fan regulator EME type 450 watt complete all as specified.

S&F in repair modular socket 6 Amps 2 /3 pin 2 module 230 volt complete all as specified.

S&F in repair modular switch 1 way 6 Amps 1module 230 volt grade complete all as specified.

S&F in repair modular switch 2 way 6 Amps 1module 230 volt grade complete all as specified.

S&F in repair modular switch socket combination 2 /3 pin 6 Amps 2 module 230 volt complete all as specified.

S&F in repair modular Switch socket outlet multipurpose 3 pin, 15 amp and two pin, 5 amp controlled by one switch 230 volt complete all as specified.

S&F in repair modular bell push flush type 5 Amps 230 volts complete all as specified.

S&F in repair modular step type electronic fan regulator 2 module 80 watt complete all as specified.

S&F in repair white cover plate with frame,2 module complete all as specified.

S&F in repair white cover plate with frame,3 module complete all as specified.

S&F in repair white cover plate with frame,4 module complete all as specified.

S&F in repair white cover plate with frame,6 module complete all as specified.

S&F in repair white cover plate with frame,8 module complete all as specified.

M&L concealed submain wiring complete with 10 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 10 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 25 mm dia with all PVC accessories complete all as specified. Note: Two runs of 10 sqmm and one run of 10sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

M&L concealed submain wiring complete with 6 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 6 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 20 mm dia with all PVC accessories complete all as specified. Note: Two runs of 6 sqmm and one run of 6sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

M&L concealed submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 20 mm dia with all PVC accessories complete all as specified. Note: Two runs of 4 sqmm and one run of 4 sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

Supply and fixing of distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt, 415V of the following DBs :-Makes -L & T / Legrand.

(a) 4 way TPN with busbar 415 volts (double door) complete all as specified.

(b) 8 way SPN with 200 amps rated busbar 240 volts (double door type) complete all as specified.

(c) 4 Way SPN with 200Amp rated busbar 240V (Double door type) complete all as specified.

S&F MCCB's, MCB's of following capacity :-

(a) MCB TPN 63 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(b) MCB TPN 32 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(c) MCB SP 6-32 Amps, 240 volts,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(d) MCB SPN 6-32 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(e) MCB SPN 40 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

Supply and fixing in replacement of 20 watt LED tubelight fitting retro fit type 4Xfeet long with replacable rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified.

Supply and fixing sensor based 20 watt LED tubelight fitting batten type 4X feet long with rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified. Make Havells of Model No: R20RBA or equivalent in crompton / Phillips

S&F in repair lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all incl 9watt LED lamp complete all as specified.

S&F in repair modular sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 25 Amps, 240 volts complete all as specified.

S & F in repair street light GI bracket of 0.6 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 40 x 6mm including nuts bolts & washers complete necessary fixing arrangements on pole complete all as specified.

S&F in repair 35/36 watts LED street light fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light source with warranty option of 5 years and suitable drivers etc and connecting with 2.5 sq mm solid aluminium conductor PVC insulated twin core weather proof cable from fittings to over head lines or to the jucntion box and fixing to complete all as specified. Make crompton Cat: LSTS-36 CDL-M or equivalent in Bajaj/Havells/Phillips

S&F in repair LED light fitting 14 W,230V decorative wall mounting type with multicolour ABS housing with poly carbonate rings and glass shade with lamp holders & Bulb with connector block,etc complete with all accessaries pre wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified. Make Havells of Model No:LHFOECE1TZ1O014 or equivalent in crompton / Phillips

Supply and fixing LED mirror light fitting with high out put with low energy consumption of capacity 6 watt,waterproof moisture anti-fog anti-corrosion anti-rust,curved LED off-white including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

Supply and fixing in repair LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified.

Supply and fixing round/square shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

M & L in repair for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.50 Mtr below the ground level connected to GI earth wire 4mm dia by means of bolts, nuts and washers protected by GI tubing light grade 15 mm dia uptoTest point, 20 mm dia GI watering pipe medium grade with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates with 8 mm reinforcement bors @ 15 cm c/c bothway complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in soft/loose soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm complete all as specified. (Note:- Up to7.5Mtr length of pipe of 15 mm dia and GI wire shall be deemed tobe included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5) will be measured separately under respective item

S&F in repair LED drivers rated voltage 12/24 volt max out put power Panel Driver for 600 mm x600 mm ceiling light of capacity 24 W/ 36 W complete all as specified.

M/L for taking out Unsv U/G cable PVC insulated armoured PVC sheathed Al. Conductor, LT cable of any size complete all as specified.

Excavation in trenches, n. exc 1.5 Mtr wide and n. exc 1.5 Mtr in depth for foundation / laying of cable and getting out in soft/loose soil complete all as specified.

Returning filling in including spreading levelling, watering and well ramming in layers not exc 25 cm thick using suitable excavated soil complete all as specified.

Removing excavated soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified.

Supply & laying unwashed local river sand for sand cushioning and covering the under ground cable in trenches complete all as specified. (Note :- Punned thickness shall be measured.)

M & L for brick protection with sub class B bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as specified.

Supply, laying, testing & commissioning of LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole of the following sizes:-

(a) 25 Sqmm 4 core

(b) 16 Sqmm 4 core

(c) 10 Sqmm 2 core

(d) 6 Sqmm 2 core

Taking out old unsv gang box and S&F Gang box switch socket combition for 5 Amp complete all as specified.

Taking out old unsv gang box and S&FGang box switch socket combition for 15 Amp complete all as specified.

Taking out old unsv copper conductor and S&F 1.5sqmm copper conductor complete all as specified.

Taking out old unsv copper conductor and S&F 2.5sqmm copper conductor complete all as specified.

Taking out old unsv socket and S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type multi purpose type 230 volt complete all as specified.

Taking out old unsv switch and S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified.

Taking out old unsv socket and S&F Socket outlet 3 pin 15 amp flush type multi purpose type 230 volt complete all as specified.

Taking out old unsv switch and S&F switch piano flush button single pole one way 16/15 Amps 230 volt grade complete all as specified.

Taking out old unsv lamp and S&F LED lamp of cap 9 watt,6500K complete all as specified.

Taking out old unsv lamp and S&F LED lamp of cap 14 watt,6500K complete all as specified.

S&F Lighting Poles Made from CRCA,witjh decorative side arms,antiquely designed for architectural street lighting applications,suitable for mounting double street fittings with LED Street light (40W capacity - 02 No.) antiquely designed aesthetically appealing landscape cum steet light,made from aluminium housing,clear polymer diffuser to provide uniform and pleasant light output IP65 Type with complete accessories and complete all as specified.

S&F Globe LED Post Top Gate light 15 watt capacity made from engineerining grade polymer supplied along with B22 bulb white/warm white ,IP65 type fixing on wall with connecting suitable wire complete accessories and complete all as specified.

Supply and fixing based 20 watt LED tubelight fitting batten with rechargable with backup minimum 30 minutes 4 X feet long with rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified.

Supply and fixing of Lithium base Energy efficient integrated Solar street light of 30 watt in Aluminium Die casting body ,corrosion resistance,built in high efficiency solar panel and long life lithium ferro phosphate battery with high efficiency microprocessor based charge controlar Automatic dusk to input voltage 12.8 V with minimum 30 AH battery capacity ,Driver efficiency .85%,PV module minimum output capacity 60 W/h Mono itself will be used to sense the ambient light to switch ON/OFF the Lamp from outside from Light fittings and controled from Pole controlling switch,inbuilt MPPT charge controller,IP65,both PIR and fixed dimming available,4500 lumens (at full brightness) with grater than 150 lumen per watt,5700ANSI,,CRI.70,moptical used, Metal core PCB,Low voltage cutoff ,high power LED,wide beam Angle(135/85 degree) with PIR Sensor LED Life 50000 hrs (LM80 cerified LED),weight less than 15 kg with Green/Red indicator with with battery rating 12.8V-BIS standard along with 5 year warranty covered complete all as specified. Make : Orient / Havells / Phillips

unique traders (BID ID -3386163)

Balaji Associates (BID ID -3387106)

Sadhana Enterprises (BID ID -3379942)

krishna Associate (BID ID -3373515)

BUILDTECH ASSOCIATES (BID ID -3379281)

M/S MAMTA CONSTRUCTIONS (BID ID -3379202)

PD GUPTA AND COMPANY (BID ID -3386812)