Certain special repair, minor works and revenue works in the AoR of AGE E/M under GE Kapurthala

S&F ceiling fans complete with blades, canopy, suitable regulators down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CMM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and connecting up and including provision of twisted three core PVC insulated flexible cord of 0.75 Sqmm copper conductor of required length from ceiling rose/connector to fan complete all as specified and directed. Make : Atomberg/Havells/Bajaj/Crompton

M&L for excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and getting out including trimming of sides complete all as specified and directed by Engineer-in-Charge.

M&L for returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer compete all as specified and directed by Engineer-in-Charge.

Supply, laying jointing and testing under ground XLPE armoured cable insulated and PVC seathed LT 1100 volt grade (heavy duty) with stranded aluminum conductor of size 35 Sqm 3.5 core confirming to IS laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed by the Engineer-in-Charge.

(ii) size of base plate 520mm thick 25 mm dia complete all as specfied each set-01 Nos (iii) Lantern Carriage:- Lantern carriage ring with class BMS pipe/tube having sleeve on carriage ring 535 mm (ID) dia suitable to mount 08 Nos of lentern fitting symetrically -01 Nos. (iv) Winch :- Winch double drum type having operating speed 180 RPM and gear ratio 53 : 1 working operating manually/electrically with stainless steel wire rope 6mm dia two point suspension system including timble copper Talurit capacity 500 Kgs (per Drum) make lubrication arrangement self lubricant in permanent oil both bath type SAE-90/140 or equivalent each Job -01 No. (iv) Winch :- Winch double drum type having operating speed 180 RPM and gear ratio 53 : 1 working operating manually/electrically with stainless steel wire rope 6mm dia two point suspension system including timble copper Talurit capacity 500 Kgs (per Drum) make lubrication arrangement self lubricant in permanent oil both bath type SAE-90/140 or equivalent each Job -01 No. (v) Stainless steel wire rope:- Diameter of SS rope 6 mm, AISI 304 grade, construction of SS rope 7/19 , stainless steel of centre core material DIN 3060, 3 Nos rope of 6 mm for Lantern Carriage, 2 Nos of 6 mm for Double drum Winch, breaking load capcity of SS wire rope are 2350 Kgs per SS rope. (vi) Trailing Cable :- Copper conductor cable PVC sheathed 1100 volt grade of size 4.00 Sq mm PVC insulataed from electrical box to street light fittings separately for nine fittings each Job -01 No. (vii) Push button control 415 Volt 3 phase 50HZ 1440 RPM single speed 1100 watt torque lifting capacity 750 Kgs adjustable mechanically tripping device complete all as specified. (viii) Power Tool:- 1.5 HP motor integral model, single speed, reversible 415 volts/240 Volts with mechanical tripping facility.

ing cable, push button, power tool etc as specified by the manufacturer. (a) Bottom dia - not less than 485 mm . (b) Top dia - not less than 200 mm suitable for bearing wind velocity as per IS 875 (Part III) (c) Lighting protection finial -G. single spike of length 1200 mm

CI pipe 150 mm bore complete all as specified.

GI pipe of 15mm bore complete all as specified.

GI pipe of 20mm bore complete all as specified.

GI pipe of 25mm bore complete all as specified.

GI pipe of 40mm bore bcomplete all as specified.

Refixing old rerived srviceable GI pipe line on trench/wall/floor/roof of following sizes

CI pipe 150 mm bore complete all as specified.

GI pipe of 15mm bore complete all as specified.

GI pipe of 20mm bore complete all as specified.

GI pipe of 25mm bore complete all as specified.

GI pipe of 40mm bore bcomplete all as specified.

CI pipe 150 mm bore complete all as specified.

GI pipe of 15mm bore complete all as specified.

GI pipe of 20mm bore complete all as specified.

GI pipe of 25mm bore complete all as specified.

GI pipe of 40mm bore bcomplete all as specified.

DI K7 pipe 150 mm bore complete all as specified.

CI pipe 100 mm bore complete all as specified.

DI K7 pipe 150 mm bore complete all as specified.

CI pipe 100 mm bore complete all as specified.

(ii) Lantern Carriage:- Lantern carriage ring with class BMS pipe/tube having sleeve on carriage ring 535 mm (ID) dia suitable to mount 09 Nos of lentern fitting symetrically -01 Nos. (iii) Winch :- Winch double drum type having operating speed 180 RPM and gear ratio 53 : 1 working operating manually/electrically with stainless steel wire rope 6mm dia too point suspension system including timble copper Talurit capacity 500 Kgs (per Drum) make lubrication arrangement self lubricant in permanent oil both bath type SAE-90/140 or equivalent each Job -01 No. (iv) Stainless steel wire rope:- Diameter of SS rope 6 mm, AISI 304 grade, construction of SS rope 7/19 , stainless steel of centre core material DIN 3060, 3 Nos rope of 6 mm for Lantern Carriage, 2 Nos of 6 mm for Double drum Winch, breaking load capcity of SS wire rope are 2350 Kgs per SS rope. (v) Trailing Cable :- Copper conductor cable PVC sheathed 1100 volt grade of size 4.00 Sq mm PVC insulataed from electrical box to street light fittings separately for nine fittings each Job -01 No. (vi) Push button control 415 Volt 3 phase 50HZ 1440 RPM single speed 1100 watt torque lifting capacity min 750 Kgs adjustable mechanically tripping device complete all as specified. (viii) Power Tool:_ 2 HP motor integral model, single speed, reversible 415 Volts with mechanical tripping facility.

DI K7 pipe 100 mm bore complete all as specified.

Supply and fix in replacment of gun metal globe or gate valve with iron wheel head screwed both ends suitable for galvanised pipe 20 mm bore complete all as specified.